Search Documents

By B P. Wrench, N R. Steward, C Wu

A gold mine in southern China has transitioned from an open pit operation to a fully underground mine. An overhand mining method is used which requires the mined stopes to be filled with backfill having an unconfined compressive strength of at least 0.35MPa. Tailings from the process plant is deposited into separate flotation and Carbon in Leach (CIL) tailings storage facilities. The tailings has a high fines content and the thickener on site could only produce a dilute flotation tailings at a solids content of about 30 wt%. This resulted in two undesirable outcomes: the density of flotation tailings in the Tailings Storage Facility (TSF) was significantly lower than planned so that the TSF could not store the life of mine tailings and that the backfill product had to include a high percentage of manufactured aggregate and increased cement content to achieve the required strength. This paper presents results of a tailings study which identified that the flotation TSF would be capable of storing the remaining life of mine tailings if an amended backfill product made up of 100% of flotation tailings could be introduced. A 100% tailings backfill with the addition of 8% cement was developed by classifying the tailings and using the coarser fraction in the backfill. This backfill allowed 60% of the flotation tailings to be placed underground and only the remaining 40% in the flotation TSF. A new thickener was designed and installed to thicken the tailings and rheological testing of the tailings, using a closed loop pilot plant, provided parameters to upgrade the underground reticulation system to deliver cemented backfill to stopes throughout the mine and to deliver thickened tailings to the TSF. The revised design was implemented and has resulted in considerable cost savings. CITATION:Steward, N R, Wrench, B P and Wu, C, 2018. Optimisation of surface tailings storage and tailings backfill – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 454–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By James D, Dawson N

The alternate mineral dressing tech-niques for the production of ilmenite roaster feed from heavy mineral concentrate and the reasons for the selection of wet high intensity magnetic separation (WHIMS) at Richards Bay Minerals are outlined.Initial flowsheet studies were under-taken using laboratory scale equipment followed by on site pilot testing. Flowsheet development culminated with an extensive test programme conducted at Readings of Lismore in 1975.

Jan 1, 1986

By Johns AS

Comissioning of a new residue disposal tcluding upgraded classification for none backfill preparation, new variable speed pumps and a new residue dam took place in 1¦76. The system is described.

Jan 1, 1978

By Bourgeois F

The population balance concept has provided a useful framework for the description of the operating behavior of the ball mill. This approach finds expression in the so-called selection breakage function model for batch and continuous mills. This model produces very good descriptions of the size distribution of the products from ball milling operations and the model is very useful for the description of batch and continuous mills and, when combined with models for classifiers and other unit operations, provides a solid basis for flowsheet simulation procedures. The breakage and selection function model is essentially descriptive and not predictive because the parameters in the model cannot as yet be related to the fundamental material properties of the material that is broken and to the fracture mechanics that govern the comminution of brittle particulate material during the rapid impact and compression events that occur with high frequency in a ball mill. The population balance approach smears over the individual processes and regards the ball mill as a continuum with breakage occurring continuously in time and space. New experimental techniques, particularly the adaptation of the Hopkinson bar as the ultrafast load cell (UFLC) to the problem of observing the extremely rapid impact fracture of particulate solids, have made it possible to make accurate and consistent measurements of particle strength, particle fracture energy and the single-impact breakage function. These quantitative measurements have been incorporated into a new conceptual model for the description of the ball mill. The model is based on identifying all events that give rise to particle breakage, and using the fundamental experimental data obtained on the UFLC and other single-particle fracture tests, the probabilities of these events can be independently determined. The distribution of impact energies that occur in the ball mill has been established by discrete element simulation of the media motion. The probabilistic description of the individual fracture events and the distribution of impact energies are combined to make a priori predictions of ball mill performance under a variety of operating conditions. The new model is used to calculate the selection and breakage functions for quartz in a small batch mill.

Jan 1, 1993

Computer-based block modelling of orebodies is now used at Renison Tin mine for the estimation of ore reserves. It is considered that this has resulted in improved reserve estimation for complex 'stratafault' orebodies. The results for all orebody types are more easily understood by the mine planning section and provide greater scheduling capability than those from the previous manual isoline reserve estimation method. A structural overview of the deposit can be gained by combining geological block models for the various orebodies. It is anticipated that upon completion of block modelling for all the orebodies the time spent on the annual ore reserve estimate will be significantly reduced.

Jan 1, 1990

By X Li, H Alehossein

The oscillating disc cutter (ODC) is an innovative technology for the continuous excavation of hard rock. This paper will discuss:the reasons for its development;its method of operation;current experimental results and mathematical modelling undertaken at the CMTE; andapplications in the mining and rock excavation industry.

Jan 1, 1999

By Hall C. E, Chrisholm J. M

Resource calculations for shear hosted deposits of any type are difficult regardless of which calculation technique is used. One of the main problems is the determination of the geometry of the mineralisation. Once this has been elucidated then the appropriate resource calculation methodology can be employed with a search distance and orientation that is relevant.

Jan 1, 1993

By Evans R, McCallum P

Modem blast initiation systems allow users many options for connection and application in the field, and have resulted in more innovative and complex uses of sequencing to influence blast outcomes. However, no tool existed which allowed the blaster to easily and quickly assess the effect of different options. The original requirement was for a computer program which allowed the easy input of blast patterns and the associated initiation sequence, and then permitted the evaluation of different options with respect to established criteria such as the number of holes per delay and angle of initiation. The implementation of this goal saw the development of the SHOTPIan blast sequence design software, with particular emphasis on an easy-to-use menu driven interface and visualisation of the blast sequence. Extensive trialling during development saw the incorporation of additional features requested by industry such as the ability to import from established mine design software packages, and further features such as the calculation of burden relief times. Case studies of the use of the program are provided, where the rapid evaluation of a number of options has enabled blast results to be optimised. Examples are also given of cases involving two-path initiation

Jan 1, 1995

By H G. Poulos

Prediction of ground deformation caused by soft ground tunnelling is an important problem facing design engineers. The ground deformations are caused by the closure of the gap formed around the tunnel due to the tunnelling procedure and soil intrusion via the tunnel face into the tunnel. There are three different approaches that are commonly used in practice to estimate the ground deformations due to tunnelling, namely, empirical methods, analytical methods and finite element methods. One of the important issues of tunnelling in urban areas is the assessment of the likely impact on adjacent pile foundations of ground movements arising from tunnel construction. The main objectives of this paper are two-fold: first, to assess the available methods to estimate the tunnelling-induced ground deformations, and second, to examine the effect of such ground deformations on adjacent piles. Analytical solutions to predict the tunnelling-induced ground deformation developed by the authors are used in this study. These estimated ground deformations are imposed on the pile in simplified boundary element analyses to compute pile responses. The influence of various factors such as tunnel geometry, ground loss ratio, pile diameter and ratio of pile length to tunnel depth are examined in this study.

Jan 1, 1999

A relationship is predicted between oxidic nickel in slag, oxygen in matte and Ni/Fe ratio in matte after the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters. Oxidic nickel in slag is found to increase with increase in oxygen content of matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1979

The use of rubber-tyred equipment in a decline mining system requires that roadways be kept free of running water. At Renison this is achieved by the use of stage pumping or gravitating to a major pump station and pumping from there directly to the surface. The frequent use of pick-up lines and pump boxes in the decline system provides a method of water control and reduces the amount of slimes in pump lines. The Bassett Fault structure, which lies on the hangingwall of the mine is the major source of ground water. This is encountered in diamond drill holes and exploration develop- ment. Dewatering of this structure is possible by controlling the flow from selected holes. Future pumping requirements may be predicted by analysing changes in the level of the water table and by calculating dewatering rates required to maintain ore reserves available for production.

Jan 1, 1977

By B Bendtsen, L McQueen

The use of shotcrete as an efficient means of both temporary and permanent ground support has continued to grow over the last 30 years, with its use underground now commonplace around the world. However, the development of analytical design methods has lagged advances in material and application technologies. Historically, part of the reason for this was a lack of understanding of how shotcrete linings actually worked. Considerable progress has been made in this area in recent years and this paper attempts to summarise the current state of practice with respect to shotcrete lining design. It then concludes by summarising areas where the authors consider future research and development is still required.

Jan 1, 2008

The mining industry has been slow at adopting the latest management philosophies from other industry sectors, such as manufacturing, and in retrospect, with good cause. With the plethora of three-letter-acronyms such as TQM, JIT, TPM and now, BPR each touted as the panacea for profit improvement, you wonder if you must choose one or attempt to embrace them all! In truth, each new insight into organisational behaviour bears some investigation. This paper looks at the underlying principles and elements of successful change strategies, and how several mining companies, including coal mines, in Australia, Chile and Canada, are applying these principles to their operations. These examples illustrate the need to think radically, and to view mining as an overall process delivering value to the customer rather than a collection of functional silos. They also show that often, a continuous improvement initiative is not enough when a fundamental redesign, a paradigm shift, is needed for a performance breakthrough.

Jan 1, 1998

By Wygralk A, Hallenstein CP

On a world scale, many Mid-Proterozoic fluvial sediments are prospective for low grade, large-tonnage gold deposits. A significant area of the Northern Territory is covered by such Mid-Proterozoic sediments, the gold potential of which has been barely tested. The geological knowledge of these sediments is summarised. The Westmoreland Conglomerate, the basal Mid-Proterozoic formation of the McArthur Basin, has been subjected to detailed sedimentological studies in order to determine the paleoenvironments and to assess the possibility of paleoplacer occurrences. The results indicate that the sandstones and conglomerates of the formation were deposited by braided rivers and debris flows as an alluvial fan which originated in source areas to the north east. The formation contains several upward-fining cycles of sedimentation, which are related to repeated periods of uplift in the source areas. The formation of placer-type gold occurrences is possible in such depositional environments. Very limited heavy mineral sampling has indicated a cassiterite- wolframite-gold suite in the sediments of the Westmoreland Conglomerate. Disconformities at the base of sedimentation cycles are deemed to be the most likely sites for large-tonnage paleoplacer concentrations.

Jan 1, 1984

By Haines P. W, Sweet I. P, Rawlings D. J, Page R. W, Plumb K. A

Current regional geoscientific studies across the McArthur Basin as part of the National Geoscience Mapping Accord by the Northern Territory Geological Survey and Australian Geological Survey Organisation have provided a significant amount of new data which has enabled revision of the stratigraphic and chronologic framework of the basin. This paper provides an overview of these results, with particular emphasis on new results from Arnhem Land.

Jan 1, 1994

Ore Reserves estimation for the two producing copper orebodies at Isa Mine, Mount Isa, Queensland is discussed. The principal estimation techniques used and discussed are first, a computer based inverse power distance weighted assay meshing technique, and second, a manual arithmetic averaging technique. The principles involved in these techniques are compared, and their areas of application indicated. A general comparison of the estimation of reserves with eventual production is presented.

Jan 1, 1979

The transportable moisture limit of a mineral concentrate (TML) is of great importance in the shipping of that material from Australian ports. Each year Australian mining companies incur substantial costs as a consequence of delaying shipments and/or multi-handling concentrates so as to comply with transportable moisture limits. Despite this there is a general lack of in-depth knowledge concerning factors that influence the parameter. Eight major Australian mining companies supplied sizing, specific gravity and TML data for their concentrates. Zinc, lead, copper and bulk concentrates were represented in their data. Estimated surface areas of the concentrates, as calculated from their normalised sizing data, correlated strongly with the reported transportable moisture limits. This high correlation prevailed in spite of the acknowledged limitations associated with the use of multi-sourced data and the adoption of simplistic approaches in the normalisation of sizing data and the estimation of surface area. Based on the broad range of concentrates studied, concentrate sizing data were concluded to offer potential as an alternative means of reliably estimating transportable moisture limits.

Jan 1, 1993

Programmes of environmental investigations to identify and minimise impacts and satisfy government and community requirements have become an integral and rate determining component in the planning and development of new mines in Australia. This paper reviews the essential features of the environmental project management Function.

Jan 1, 1983

By Weller KR

A study of high pressure rolls grinding of a number of Australian ores and minerals has been carried out using a pilot-scale machine with rolls 300 mm diameter and 70 mm wide. The results from this study have been used in conjunction with plant survey data to construct computer simulation models of various comminution circuits and these have been used to investigate options for incorporating high pressure grinding rolls into these comminution circuits. Possible rolls options for three of these circuits are presented, and likely energy savings over the existing circuits are discussed together with potential improvements in plant throughput and/or product sizing. A scale-up procedure for predicting full-scale machine performance from small-scale testing is described, and the effects of rolls operating conditions are also discussed.

Jan 1, 1991

By J Johansson, B Johansson

The mining industry needs to attract and recruit young talented people. An important task is, therefore, to create an attractive mining workplace that engages with, and motivates youngsters who are not particularly interested in working in the industry. This paper aims to illustrate a way forward for the mining industry to form healthy and safe workplaces honouring key components such as knowledge, skill, co-operation, continual development and acceptance of diversity. This is a way to create a vision of healthy and safe mining work. The mining industry must work towards zero vision; a future without accidents and hazardous environments. In this paper the authors discuss different aspects of an ‘attractive workplace’ and summarises lessons learnt in 26 statements dealing with safety, both physical and social work environments, and social responsibility. The authors hope these recommendations will provide some guidance for how attractive workplaces should be designed for future deep mining.The paper is based on lessons from two large European projects, a Swedish-Polish project: The Smart Mine of the Future; and a European Union project: Sustainable Intelligent Mining Systems (SIMS). One of the authors was the WP leader of health and safety in both projects.CITATION:Johansson, J and Johansson, B, 2017. Attractive workplaces in future underground mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 99–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017