Search Documents

By G W. Wilson

Rehabilitation of tailings impoundments is one of the most challenging aspects in mine closure, as not only does the potential for producing leachate pose a challenge to the rehabilitation designer, but also other aspects such as stability and settlement must be considered. The water balance of a tailings impoundment is unique in the sense that it usually hosts a pond that in turn causes a phreatic surface in the impoundment. The position of the phreatic surface defines the saturated and unsaturated zones in the impoundment, which of course varies spatially and temporally. Predictive modelling for this hydrologic system becomes difficult, as numerical models capable of analysing the combined saturated/unsaturated zones are not adequately refined to accurately solve the flux boundary problem for infiltration at the surface of the tailings. This paper describes the development of a flux boundary model that enabled accurate modelling of the unsaturated zone in the tailings impoundment at Kidston Gold Mine, Queensland, Australia. The technique made it possible to accurately predict the spatial variation of infiltration to the tailings as a result of the presence of the phreatic table. The conceptual model defines the boundaries for the Kidston tailings dam, based on a generalised cross-section through the dam. Firstly the shape of the top boundary is described as a function of the particle size of the tailings associated with particle segregation that occurs due to the hydraulic placement of tailings. This function was rigorously tested using in situ infiltration tests and laboratory materials testing. Defining the bottom boundary of the section, ie the phreatic level was done by physically monitoring the phreatic level with 42 piezometers strategically located on the tailings dam. Analysis of this data led to the fixing of this bottom boundary through the introduction of a function that mimicked the shape of the phreatic level. The material properties of the surface layer, specifically the saturated permeability that would govern the infiltration/exfiltration rates of moisture through the top boundary layer were defined on the basis of extensive field and laboratory material testing. A function for the saturated permeability was developed on the principles of particle segregation. Finally a procedure is described for the application of the new conceptual model for the evaluation of the spatial infiltration to a tailings surface using the rigorous one dimensional surface flux boundary code SoilCover. The solution of the calculation described above was then used as the top boundary condition in conventional three dimensional saturated/ unsaturated flow codes, and verified against measured seepage rates from the tailings impoundment under drains. It was concluded that the developed spatial flux function was in deed a most rigorous representation of reality. Although the methodology presented here was applied to the Kidston tailings impoundment only, the authors believe that the principles are directly transferable to any tailings impoundment that has a varying phreatic zone thickness due to the presence of a pond. The mathematical equations describing the typical cross-section would be site specific, but the approach and ultimate solution methodology would be directly transferable.

Jan 1, 2003

The history of the down draught Dwight- Lloyd system of iron ore sintering in Australia is developed. Characterisation of the broad process is given for one plant, and regional divergences from the reference practice are noted and briefly analysed. The subject of the development of high basicity sinters is introduced, and regional differences in approach and results are Examined.

Jan 1, 1972

By M Lellis

During the last decades, maintenance has changed from an ordinary repair activity to a complex function that plays an essential role contributing for the companyÆs results. The increasing level of complexity of modern equipment motivates maintenance personnel to improve both techniques, and management systems, in order to face the new challenges. Managing properly those modern means of production requires knowledge of methods and planning systems, controlling and performing maintenance tasks, in such a way that two objectives are achieved at the same time: system efficiency and cost-effectiveness. This paper shows CVRDÆs experience on evolving and implementing a model to plan and manage maintenance activities in order to achieve a higher level of performance on its operations.

Jan 1, 2003

The three main types of iron ore deposits in Australia are bedded, massive and residual. Some character- istics of iron ore, important in its process behaviour, are related to its mineralogy which is a result of its geological history. World iron ore resources are extremely large but there are problems in quantifying re- serves, defined as that part of re- sources from which a useable commodity can be extracted economically. The relationship between the discovery and exploitation of iron ore resources and the process of industrialization is examined in historical and present day contexts.

Jan 1, 1976

By C. P. BATES

In November 1969, New Zealand Steel Ltd pioneered the commercial use of the SL/RN solid fuel direct reduction process to make sponge iron as a feed material for electric arc furnaces. Serious process problems with the use of green balls and coal injection were progressively overcome. The process was developed by New Zealand Steel along a radical route, of feeding the fine grained raw ironsand concentrate and coal directly to the kiln. Contemporaneously with this development of direct reduction, steelmaking process innovations were made that enabled the arc furnaces to operate successfully with the high volumes of acid slag.

Jan 1, 1980

Geologists employed by Metals Exploration Pty. Ltd. discovered nickel enrichment at Greenvale, 180 kilometres West of Townsville, in 1967. Subsequent drilling proved an ore body containing 45 million dry tonnes of ore containing an average of 1.5% nickel and 0.11% cobalt. The Freeport Minerals Company, who had experience in treating lateritic nickel ore, were invited to participate in development of the ore body. This resulted in the formation of the operating company Queensland Nickel Pty. Ltd., jointly owned by Freeport Queensland Nickel Inc. and Metals Exploration Queensland Pty. Ltd. With the completion of successful pilot plant testing of Greenvale ore at the Freeport research facilities at Belle Chasse, Louisiana, a treatment plant was constructed at Yabulu, 24 kilometres North West of Townsville. A 225 kilometre railway line was built connecting the Greenvale Mine and Yabulu Treatment Plant. The ore reduction and ammonia/ammonium carbonate leaching flowsheet is similar to that constructed and operated by the Freeport Minerals Company during World War II at Nicaro, Cuba. Modifications to the Nicaro flowsheet implemented at Yabulu include facilities to recover cobalt in a mixed nickel/cobalt sulphide product and the reduction of nickel

Jan 1, 1978

By A Purchase, C Stacey

The procedure for operation of deluge systems installed in road tunnels is still a subject of debate. The work undertaken in this paper assists in the understanding of the effects of deluge in road tunnels, and thus aims to help inform the development of operational policy. Analysis was undertaken using computational fluid dynamics (CFD) simulations to help explore the deluge interaction with the tunnel ventilation (including smoke exhaust) and combustion products. It was found, for the scenarios considered, that: Deluge activation can decrease the required critical velocity for smoke backlayering, and this in turn can improve the effectiveness of a smoke exhaust system.The dominant parameter for deluge effectiveness is the vehicle configuration, with shielded scenarios (such as a fire in the passenger compartment) showing almost no water reaching the fire. The water delivery rate (5 mm/min versus 10 mm/min) has only a minor effect on the smoke duct damper inlet temperatures and downstream smoke temperatures for small fires (5 MW). For large fires (50 MW) the higher water delivery rate gives slightly improved performance (lower damper inlet temperatures and lower downstream smoke temperatures). A one-dimensional transient tunnel model incorporating different operational and deluge response policies (ie deluge activation times) was developed. It was used to examine the influence of different operational parameters on life safety risk and tunnel damage risk. It was found, for the scenarios considered, that: The life safety risk for different scenarios has a sensitivity to deluge activation policy with the case of delaying the deluge activation for a long time giving the worst outcomes. However, the most critical parameters for life safety risk are operator response time (for all response activities, not just deluge) and the type of fire (configuration, size and growth rate).There is a reduction in risk of tunnel damage when the deluge is activated earlier, although the fire configuration (ie whether or not the seat of the fire can be reached) has the greatest influence on the outcome. It is concluded that the deluge activation policy should be case-dependent. It will depend on the tunnel, the safety systems provided, and most particularly the vehicles involved. The current policy in Australian tunnels is for manual activation of the deluge by the tunnel operator as soon as practical after the fire is confirmed (see also PIARC, 2007). This is a good policy. However, future work may be helpful to improve the skills of operators to make the best judgement as to when deluge should be activated, balancing all risks. This work could include research to further the understanding of deluge and fire in road tunnels, training programs and consideration of historical fire events.

Jan 1, 2008

By Somasundaran P

Controlled modification of mineral/liquid interfacial properties by adsorption is critical for mineral processing operations such as flotation, filtration, dispersion and flocculation. Ionic/nonionic surfactant mixtures usually show enhanced surface activity and salt tolerance over ionic surfactants, and this is especially beneficial for flotation of salt type minerals in which case dissolved multivalent cations in high concentrations usually cause loss of anionic surfactants by precipitation. Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied with sodium dodecylsulfate as the anionic surfactant and octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactants was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in flotability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also' for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant species at the interface. Also, based on the results obtained with surfactant adsorption, a hydrophobically modified polymer was used successfully to disperse graphite particles in aqueous solution.

Jan 1, 1993

The direction taken by mineral processing in the next 20 years will be determined by sharing of Australia's resources to fill world needs; by the low energy costs in Australia; by environmental considerations; and by Re- search and Development contributions. Examples of the interplay of these factors are given by consideration of eight minerals.

Jan 1, 1981

By Kister H

Hoesch HUttenwerke AG, Dortmund, West Germany, is an integrated steel work of the Estel-group. The nominal annual production capacity-is about 7 Mio tons of steel. Hoesch has along experience in operation of diffe-rent types of slag granulation plants and of utilization of the granulated product. This experience is used to granulate a large amount of blast furnace slag and to process it in own cement plants and produce blast fur-nace cement.

Jan 1, 1979

Following plant trials in 1972 Mount Lyell installed an AMDEL On Stream Analysis system for measuring copper and density on the flot- ation feed and final plant tailing streams, in August 1973. As a result of poor performance of the final tailing system these probes were changed over to the rougher tailing stream, back to the final tailing stream and finally to the final copper concentrate stream where the system is currently performing satisfact- orily. The history of the development of the system to its current operational status is Described.

Jan 1, 1978

By Spencer PA, Winborne DA

The Porgera mineral deposit in Papua-New Guinea contains gold as finely divided, probably submicroscopic (1 um) particles dispersed in a pyrite sulphide matrix. Only 25-30% of the gold in pyrite can be extracted by direct cyanide leaching and fine grinding the pyrite does not increase gold extraction significantly. This work is concerned with the application of alkaline leaching at atmospheric pressure to oxidise the pyrite prior to gold recovery by cyanidation. The paper presents and discusses results of a comprehensive set of testwork using sodium carbonate, sodium hydroxide and calcium hydroxide alkaline media. Best results, at 60-70% gold extraction, were obtained with sodium hydroxide systems.

Jan 1, 1984

In both surface and underground coal mines, the detection of geological structures ahead of workings is recognised as being fundamental to the efficient operation of the mine. Mining into zones of unexpected structures has a drastic effect on a mine's productivity. For the prediction of structures, geophysical methods can be applied from the air, from the ground surface, from boreholes and from underground workings. There are several improvements to report in the geophysical methods being developed for these purposes. These include developments in three-dimensional seismic reflection surveying, cross-hole seismic reflection methods and radar systems. The recent development of the radio imaging method for use in underground mine workings will complement existing in-seam seismic methods. Geophysical techniques for use in horizontal boreholes are also under development.

Jan 1, 1988

Gold recovery by catalytic copper ammonium thiosulphate solution has been studied. Such a process strategy is very attractive for leaching certain difficult-to-treat ores and presents lessened lixiviant toxicity compared to cyanide. Newmont Gold Company has evaluated the ammonium thiosulphate heap leach process for gold recovery from low-grade carbonaceous sulphidic refractory ores following biooxidation. The ammonium thiosulphate leach process has been studied in laboratory, pilot plant and demonstration scale. Satisfactory test results support the continuation of process development. However, the thiosulphate leach chemistry was found to be very complex. Maximum control of the stability of the leaching system is a key factor for success, especially for the heap leach process. Important solution chemistry is discussed in this paper.

Jan 1, 1997

The scale and seriousness of AustraliaÆs social and environmental problems are no longer in doubt. We are consuming the opportunities of future Australian generations by our lifestyle choices. And at the global level, human activities are altering the very systems on which our species depends. Doing nothing about such problems as climate change is not an option. It is possible to move to a sustainable future but it will require fundamental changes to our values and national social institutions. We must recognise that we share a common future with the entire human family and the other species with which we share the planet. It is not just our humanitarian duty to improve the lot of the poorest people of the world. It is also enlightened self-interest because a world of increasing inequality will be a world of increasingly destructive tension.

Jan 1, 2004

The annual growth in lead consumption in the Western world has declined sharply in the past ten years, as lead has suffered a wave of substitution by other materials, and has also been the object of concern about its toxicity in daily applications. Like most metal industries, the lead industry has tended to be more production-oriented than market-oriented than is the case with some of its competitors. However, in recent times this pessimism and preoccupation with weathering the threats from environmental legislation, substitution and low prices appears to have been replaced with a new optimism in some sectors of the industry. This is indicated by renewed promotional activities and efforts to find more applications and market opportunities.

Jan 1, 1985

Using a new type of laser surveying instrument named Particle Dynamics Analyser (PDA), the distributions of the radial and axial components of the mean velocity, the size and the concentration of solid particles at selected positions within a transparent hydrocyclone were directly measured out for the first time, from which profiles of the flow field of solid particles were obtained. And some new points were put forward such as the locus of zero vertical velocity (LZVV) of solid particles was not the same as that of liquid, and some particles in inner helical flow could also be separated. The results are of great significance to farther ascertain the separation principle of hydrocyclones and improve the separation efficiency.

Jan 1, 1993

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007

By Shiels O. J

The paper reviews developments in general galvanising in Australia, including a brief history of the industry and its technology. The changes in galvanising process technology are covered, as well as developments in galvanising bath design, materials handling and pre-treatment. Developments in zinc management through the use of aluminium and nickel alloys are discussed. The paper addresses the cost components of general galvanising and relates this to the competitive position of general galvanising against other coatings used for protecting steel. The environmental aspects of the general galvanising industry in Australia are outlined with respect to the utilisation of process chemicals, problems associated with their disposal and developments in filtering and regeneration of process solutions. The current status of the industry is assessed in terms of zinc usage and usage trends. Likely changes in technology which may impact on the general galvanising industry in the future are reviewed.

Jan 1, 1993

By Brown P. L

A study has been made of the geochemistry of the Ronneburg mine district as input to the overall management strategy for the rehabilitation of the mine site. The study drew on the geological data and information store developed over the 40 years of mineral exploration and mining at Ronneburg, and on chemical data from the literature which described the chemical processes of weathering, oxidation, dissolution and precipitation of minerals. The geochemical processes were divided into three groups based on their rate of reaction. Fast processes were assumed to proceed to equilibrium and were modelled using equilibrium chemistry equations; slow processes were assumed to be proceeding at a quasi-steady state rate and were modelled using chemical rate equations; very slow processes were assumed to have no role in describing the geochemistry for rehabilitation purposes.

Jan 1, 1995