Search Documents

By Zhiqing Zhang, Changyun Chen, Qing Liu, Lin Lin, Zhihong Jia, Guangjie Huang, Lipeng Ding

The effect of interrupted quenching (IQ) treatments on natural aging and bake hardening response of Al-Mg-Si alloy was investigated by hardness measurements, tensile test, differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The results show that interrupted quenching at 100oC could effectively suppress natural aging and improve bake hardening response. The optimized interrupted quenching treatment is 100oC for 45min, which gives the alloy a relatively low T4 temper strength and higher bake hardening response. The formation of highly dense cluster(2) during the interrupted quenching could be the reason for suppressing the natural aging and accelerating the precipitation of ß? phase during the paint bake treatment. In addition, interrupted quenching at higher temperature (170oC) results in unfavorable properties in both T4 temper and paint bake treatment. The formation of large precipitates is responsible for these undesired effects.

Jan 1, 2015

By A. Dubé

Introduction It is common experience that on re-heating a fully martensitic steel below the Ac, point, a softer and tougher structure is formed as the tempering temperature is raised. The mechanism of tempering of plain carbon and low-alloy steels has been the subject of many investigations. In a very comprehensive study, Cohen and associates have recently established three different tempering stages, the last of which reaches completion at about 700°F., with heating rates of 5°F. per minute. This latter stage has been established ta be the carbide-forming stage, so that the steel consists of a mixture of ferrite and carbide, which are the metastable equilibrium phases. Any subsequent changes which take place at higher temperatures below the Ac, point in the absence of graphitization or carbide lattice conversion normally consist of agglomeration of the carbide particles. This naturally results in the softening of the steel. However, in many cases the Ac, point, as determined by dilatometry, thermal analysis, etc., only gives a rough estimate of the temperature where the reaction, ferrite plus carbides to austenite, is initiated. This appears to be especially true in the case of alloy steels in which three phases can co-exist in certain temperature ranges. Bain has given data on the three-phase equilibrium in both manganese and nickel steels. In these steels, the formation of austenite at temperatures just above the AeIL apparently involves the diffusion of the alloying elements to the first pools of austenite, thereby making the process very sluggish. As a consequence, the critical Ac points determined by ordinary methods at normal rates of heating can be quite distant from the true equilibrium Ae temperatures.

Jan 1, 1946

By Wael Abdellah

Mine haulage drifts are the primary access to the mining blocks of an orebody in a multilevel mining system of a tabular ore deposit. The stability and functionality of haulage drifts are thus crucial to the success of a mining operation. Drift instability could lead to serious consequences such as injuries, production delays and higher operational cost. In this paper, the performance of the haulage drift stability is evaluated on the basis of the primary rock support system comprising 1.8 m resin grouted rebars in the drift walls and 2.1 m long bolt in the back. Two failure criteria namely the extent of Mohr-Coulomb yield zones around the drift, and linear elastic brittle shear failure are adopted and compared, with respect to lower level and same-level mining and filling sequence in the vicinity of the haulage drift. The case study is one of the #1 Shear East zone of the Garson Mine in Sudbury, Ontario. Random Monte Carlo (RMC) technique, which has been previously established to assess the haulage drift stability, is employed in this investigation. The RMC technique is used in conjunction with finite difference modelling software FLAC for random assignment of model input parameters in the FLAC grid. Deterministic model results reveal the drift behaviour in terms of deformation (convergence) and mining-induced stress distribution. Comparison between the two different criteria is carried out to determine which method is most suitable in evaluating unsatisfactory drift performance. The results are presented in terms of probability of instability and categorized with respect to failure condition and mining step. It is shown that the brittle shear failure condition based on linear elastic response calls for enhanced support system at a later mining step than what Mohr- Coulomb yielding condition does. The paper presents a detailed discussion of the stochastic analysis results.

Jun 1, 2012

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By Gordon L. Kidd

The object of this paper is to show the relations of the East Coulee coal area to the near-by Willow Creek, Wayne, Rosedale, and Drumheller areas, all being parts of the Drumheller field. The word ?area? is here used in a more local sense than that employed by Dr. J. A. Allan, whose. 'area' is rather comparable with the 'mining division' in British Columbia. I have drawn freely from the published information, particularly from Dr. Allan's report on the "Geology of Drumheller Coat Field, Alberta", and from Dr. E. Stansfield's paper on " A Chemical Survey of Alberta Coals", to whom thanks are due. The Drumheller field is served by branch lines of the two principal Canadian railways. The C.N.R. traverses the district by its Goose Lake line from Calgary to Saskatoon; and the C.P.R. by a line from Calgary to Acme and then southeasterly to Drumheller, where it effects a junction with the C.N.R., over which the C.P.R. has running rights as far as Rosedale. From Rosedale, a joint line built during the summer of 1928 extends about forty miles down the Red Deer river to the mouth of Bull Pond creek. From that point the C.P .R. turns more southerly to connect with the Bassano-Empress line. The C.N.R., it is expected, will eventually proceed eastward to connect with a transcontinental line. The joint line from Rosedale down the Red Deer river opened up the Willow Creek and East Coulee areas.

Jan 1, 1929

By Eiichi Sato, Koichi Kitazono, Hiroshi Masuda, Kenta Higane

"The present study investigated the low-temperature creep mechanisms in ultrafine-grained (UFG) aluminum manufactured by accumulative roll bonding. UFG aluminum with grain size 0.39 µm showed steady state creep even at room temperature under low stresses as confirmed by the creep curves in the strain rate–strain plot. The low-temperature behavior was divided into four regions by three distinctive stresses, sI, sII and sIII: sI (=45 MPa) is denoted as the micro-yielding stress with which dislocations start movement, sII (=85 MPa) the dislocation-multiplication stress above which dislocations multiply with creep deformation, and sIII (=171 MPa) the conventional yield stress above which macroscopic plastic strain is generated. During low-temperature creep, below sI, negligible plastic strain is generated. Between sI and sII, creep deformation with stress exponent 2.5 occurred, which is accommodated by dislocation absorption into grain boundary and grain boundary sliding, similarly to the low-temperature creep of HCP metals. Between sII and sIII, creep deformation with stress exponent 7.0 occurred, whose mechanism is similar to the low-temperature creep of coarse-grained aluminum. Above sIII, power-law breakdown occurred.INTRODUCTIONIt is well understood that the creep deformation brings about at high homologous temperatures (T/Tm) of >0.4, where Tmis the melting point, with diffusion processes. Recently, the importance of aluminum is increasing for cryogenic temperature parts such as a metallic liner or a cap in high pressure-hydrogen vessels, and the presence of creep behavior in aluminum at room temperature has become recognized (Matsunaga, 2013;Kassner, 2015).In HCP metals and alloys, especially intitanium, steady-state creep behavior appears at room temperature with apparent activation energy of1/10 of that for self-diffusion(Neeraj, 2000; Matsunaga, 2009).On the other hand, Kassner (2015) claims that aluminum shows creep behavior at room temperature with apparent activation energy of 4/5of that forself-diffusion, but never reaches the steady state. We should note that it is derived from the data obtained from short-term creep tests of few hour, and Matsunaga (2013) already claimed the presence of steady state in room temperature creep in aluminum with activation energy of 1/5of that for self-diffusion.The mechanisms for low temperature creep are considered different between HCP and FCC metals: in HCP metals, grain boundary sliding is observed and is thought to accommodate piled-up dislocations at grain boundaries through absorbing them. The so-called slip-induced grain boundary sliding occurs with low number of activated slip systems(Matsunaga,2009).On the other hand, in FCC metals, many activated slip systems bring about work hardening with dislocation cell structure formation. In the initial stage of creep, it results in primary creep (Kassner, 2015), but Matsunaga (2013) claimed that once the annihilating of a cross-slipped dislocation to another reaches balance, steady state is established. It has been, however, strongly required to show more convincing experimental verification for the presence of steady state in FCC metals at low temperature."

Jan 1, 2018

By Stephen Hardcastle

Presentation Outline ? Introduction ? Mine Ventilation Facts ? Ventilation-on-demand (VOD) ? Sensors/Controls ? Continuing Work ? Conclusions ? Mine ventilation engineering practices were published in 1556 in Agricola?s De Re Metallica (wind sails, bellows, etc.) That was then? This is today? Large fan installations handling >1M cfm

Nov 1, 2011

By Bern Klein, Tichang Sun, Daozhen Gong, University of Science and Technology Beijing, Chunbao Sun, Stefan Nadolski

"This paper is focused on the effect of modifying the SAG mill/ball mill transfer size on the energy efficiency of SABC circuits. The transfer size is considered to be a parameter which provides operators with the opportunity to improve comminution circuit performance. In this study, the Moly-Cop tools package was employed to predict the energy consumption of SAG mill and ball mill circuits under different operating conditions. An Energy Benchmarking model was adopted to calculate grinding energy efficiency. The SABC circuit at the Huckleberry mine was selected for this case study. It was observed that after increasing circuit transfer size (T80) from the existing 3.3 mm to 4.8 mm, the Benchmark Energy Factor (BEF) of the SABC circuit decreased from 4.30 to 4.05. In terms of energy consumption of the SABC circuit, 1.17 kWh/t of specific energy saving was achieved through the transfer size optimization.It was also observed that when a transfer size was selected such that both SAG mill and ball mill circuits operated at their highest energy efficient states, the entire SABC circuit was the most energy efficient. The maximum energy efficiencies of these three circuits were all approximately 25% when compared to the minimum practical energy required to carry out an equivalent comminution duty. Single-particle compression breakage testing was used to determine the minimum practical energy associated with the Huckleberry mill feed. In combination with geo-metallurgical data, this study also provides an opportunity to perform dynamic optimization of SABC circuits."

Jan 1, 2016

By N. Lecuyer

"During early 1980, pre-production work commenced at the ""Les Mines Gallen"" project, north of Noranda, Quebec. As a result of the acid mine water associated with this property, a major pre-production phase included the installation of a water treatment plant to render the water environmentally suitable.This paper emphasizes the planning, installation and operational factors of the treatment plant necessary to the success of the mining operations and the maintaining of a clean environment.Introduction,T he Gallen Project is a zinc, gold and silver open-pit mining operation approximately 10 kilometres north of Noranda, Quebec. This property has a long history, with initial diamond drilling done in the early 1930s and underground mining taking place between 1953 and 1962. This property was reactivated in 1980, with production scheduled a t a rate of 45,000 ton s per month.Included in the reactivation plans for the property was the installation of a water treatment plant to treat the acidic mine water.Plant DesignThe requirements for the Gallen water treatment plant were two-fold. Firstly, it was necessary to neutralize the acid water and secondly to produce a sludge containing metal hydroxides and sulphates which would be stable when stored, and a clarified overflow meeting governmental regulations to be discharged to the environment.The flow sheet (Fig. I) will explain the process in treatment of the acid water.Acid mine drainage is treated with lime to increase the pH to 9.50. Metals in solution are precipitated as metal hydroxides and the 504 as calcium sulphate. The precipitate slurry is then aerated to convert ferrous iron to ferric iron, which is more stable for storage and disposal.The precipitate is next flocculated with a polymer flocculant and settled in the thickener to produce a sulphate/Hydroxide sludge and a final effluent discharged to the environment."

Jan 1, 1983

By R. Amata

"The Gakara Rare Earth deposit in Burundi (East Africa) is unique for its high grade (e.g., 54.3% TREO on average) and low uranium and thorium levels. The majority of the light rare earth (RE) elements in material from Gakara are contained within the familiar RE minerals bastnaesite and monazite. Extensive metallurgical test work was conducted by SGS Minerals Services on mineral samples collected from the Gakara deposit. Various whole ore hydrometallurgical processing routes were examined in a scoping level test program. Preliminary beneficiation testing was also conducted, though it was determined that only marginal upgrading would be achieved with significant RE losses. Thus a hydrometallurgical process on whole ore was developed to minimize the overall process complexity and achieve maximum RE recovery. Results from the test work will be presented, along with the selected base case flowsheet involving agitated atmospheric sulphation of the RE minerals, RE double sulphate precipitation, caustic conversion, redissolution, and carbonate precipitation. Following the base case flowsheet, a purified cerium free mixed RE carbonate with low levels of radioactive elements was produced.INTRODUCTIONRainbow Rare Earths Limited (Rainbow) is a mining company engaged in the exploration and development of the Gakara rare earth deposit in Burundi; Figure 1 shows the project location. The project is located in the Bujumbura Province and 45 km from the Burundi capital of Bujumbura. Notable for its exceedingly high in-situ grade – 54.3% on average total rare earth oxide (TREO), low uranium and thorium levels and familiar rare earth minerals, bastnaesite and monazite – Gakara is the world’s richest rare earth deposit. The project, a previously operating mine from 1948–1978, has a significant mineral inventory base, a long life of mine, well understood mineralogy, and robust economics. Rainbow is focused on bringing Gakara into production in the near term, ramping up to produce 5,000 t/y of a 54%+ TREO concentrate."

Jan 1, 2016

By Chantale Doucet

L?utilisation du remblai en pâte dans les exploitations en vrac est de plus en plus importante. Puisque la technologie existe pour fabriquer du remblai en pâte sans construire une usine coûteuse, il est maintenant possible d?élargir le domaine d?utilisation du remblai en pâte pour y inclure des gisements filoniens où le besoin annuel de remblai est moindre. Dans certains cas, l?utilisation du remblai en pâte pourrait permettre de réaliser d?importantes économies telles que la réduction de la dilution, la stabilité des ouvertures, la récupération d?une plus grande partie du minerai par la réduction de la taille des piliers et l?entreposage de moins de résidus à la surface. L?ampleur des économies est parfois difficile à chiffrer mais il est tout de même important d?en tenir compte lors de la décision d?utiliser du remblai en pâte puisque ce sont souvent ces économies qui seront déterminantes. Différentes méthodes d?extraction avec remblai en pâte appliquées aux mines filoniennes seront présentées. Des défis et les solutions reliés à l?utilisation du remblai en pâte à la Mine Doyon seront discutés.

Oct 1, 2001

By F. McCarthy, W. Zhang, R. McDonald

"The processing of nickel laterites has been a topic of major interest at CSIRO for almost twenty years. During this period CSIRO has collaborated with other researchers and industry in developing a better understanding of existing processes and been actively involved in testing/developing new beneficiation and process options for these ores. The current paper summarises the results of selected studies and highlights improvements that have been achieved. Key topics to be discussed include enhancements in the mineralogical characterisation, beneficiation approaches, improvements in the understanding and application of leaching technologies, the development of synergistic solvent extraction (SSX) for the recovery of nickel/cobalt from laterite leach liquors and the collaborative development of the Direct Nickel process. Future opportunities and key research questions will be briefly examined.INTRODUCTION Nickel laterite ores comprise a significant resource in Australia and according to United States Geological Survey data nearly a quarter of world reserves are located there (USGS, 2016). More specifically, around 95% of Australian nickel resources (laterite and sulfide) are located in Western Australia (Australian Government, 2017). Given the recent closure of Queensland Nickel, essentially all of Australian nickel production occurs in Western Australia and the primary producers of processed nickel products include Nickel West (Kwinana) with ~84,000 t saleable nickel metal in 2016 (BHP Billiton, 2017), Minara Resources (Murrin Murrin) with 46,700 t nickel metal produced in 2015 (Glencore Australia, 2017), and First Quantum Minerals Ltd (Ravensthorpe) who sold 25,882 t nickel as mixed hydroxide product in 2016 (First Quantum Minerals, 2017). The total sales of nickel from Western Australia in the 2015-16 financial year were 175,722 t. The study of nickel laterites at CSIRO recommenced at the time second generation High Pressure Acid Leaching (HPAL) plants were being commissioned at Bulong, Cawse and Murrin Murrin in the late 1990’s. A combination of technical and engineering issues meant that the ramp-up times at these operations were slower than expected and the outcomes resulting from the attendant problems are well documented (e.g. Griffin & Becker, 2000; Reid & Barnett, 2002; O’Callaghan, 2003) while the issues faced at the BHP-Billiton-built Ravensthorpe plant have been addressed by the current owners of this project, First Quantum Minerals Ltd (Piper, 2012)."

Jan 1, 2017

By C. S. Crocker

The Centennial orebody was discovered and named in 1970, Manitoba's centennial year. It is relatively small, about 2 million tons. Strike length varies from 400 to 600 feet and widths from 10 to 60 feet; dip is 75 degrees. Low grade and metal prices demanded low-cost mining, and the mine was developed for conventional sublevel stoping. As the ore lay entirely under a large lake, ground movement had to be avoided and the stopes were to be filled hydraulically. Late in 1973, vertical crater retreat mining was introduced at Inco Limited, Sudbury, to recover pillars between filled stopes. It proved satisfactory and the results were publicized by CIL, who developed the technique. The method seemed to offer some advantages and one stope at Centennial Mine was selected to be mined by VCR while production was maintained from blasthole stopes. The trial stope was safe and showed lower development costs, reduced drilling time, a favourable powder factor and good fragmentation. VCR mining is now an accepted method at HBM&S Co., Ltd., and its use is being extended.

Jan 1, 1979

By N. R. Andrade-Gonzalez

The present work was performed on four alloys containing Al-6 2 wt pct Si-3 5 wt pet Cu, with magnesium in the range of 0.02-0 40 wt pct, and strontium in the range of 0-165 p p m Tensile bars were cast in a permanent mold (ASTM B108-160) and heat treated at 495°C for 4 hours, followed by quenching in hot water. Two different artificial aging temperatures were applied at 180 °C and 220 °C for times from 0 5 h up to 8 h Tests were conducted with the intent of determining how the mechanical properties of an aluminum-based 319 alloy are affected when aging time and temperatures are varied In general, it is seen that the alloy does not exhibit the common peak-overaged aging condition due to the presence of several coexisting phases, indicating that they form through complex eutectic reactions late in solidification.

Jan 1, 2004

By T. K. Akopyan, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"A qualitative and quantitative analysis of the new Al-Ca-Mn-Fe phase diagram in the region of the aluminium corner is carried out using both thermodynamic calculations and experimental methods. Using the obtained data, the principal possibility of creating both cast and wrought sparingly alloyed aluminium alloys with calcium, manganese, scandium and zirconium at allowable iron contents of up to 0.4% that do not require solution treatment and quenching is justified. At the selected concentrations, the entire amount of manganese (1%) is practically included in the aluminium matrix, while calcium (~2%) and iron are in the multiphase eutectic, which has a fine structure. The joint introduction of 0.25% Zr and 0.1% Sc into the alloy leads to precipitation hardening due to the formation of the L12-Al3(Zr,Sc) phase during annealing. Based on the experimental data for the model multicomponent Al2CaMnFeZrSc alloy, it is shown that such alloys can combine high mechanical properties and good manufacturability during both casting and metal forming. This is due to the combination of a narrow temperature range of solidification with a fine eutectic structure.INTRODUCTION Hardening in branded aluminium alloys (both cast and wrought) is generally achieved by heat treatment of the T6 type, including quenching and artificial aging (Zolotorevskiy, 2007; Kaufman, 2004; Mondolfo, 1976). Heat treatment significantly increases the cost of the final products. Therefore, industrial companies are interested in developing alloys that can be hardened to the desired level without quenching. To solve this problem, alloys with scandium are the most suitable (Toropova, 1998; RØyset, 2005). This element (usually in an amount of ~0.3%) is one of the most effective hardeners in aluminium alloys, due to the formation of Al3Sc (L12) phase secondary precipitates, the size of which is less than 10 nm (Knipling, 2010; Fuller, 2005). These nanoparticles are formed during the annealing via decomposition of the supersaturated aluminium solid solution (hereinafter referred to as (Al)). This feature allows us to significantly increase the strength of aluminium alloys by simple annealing (at ~300°C), i.e., without heat treatment, including quenching. However, scandium is a very expensive metal, so its use as an additive is severely limited. The most effective method is the introduction of scandium together with zirconium (Lefebvre, 2009; Booth-Morrison, 2012). The optimal combination is the introduction of ~0.1% Sc together with 0.20–0.25% Zr, which, according to (Belov, 2006), gives approximately the same strengthening effect as the introduction of 0.3% Sc."

Jan 1, 2018

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016

By George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond county, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1914, the derrick spans, 2,000 feet or more long, became unwieldy. To overcome this, and also to eliminate hand labour as much as possible, steam shovels and railway haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type.

Jan 1, 1946

By W. G. Robinson

"MINING is one of Canada's most important industries and exploration is the life-blood of this dynamic and exciting business. The health and growth of the mining industry of tomorrow depends on the effort and thought that go into exploration today. The Members of the Geology Division of the C.I.M. are directly concerned with exploration, and it is fitting that this Division should periodically sponsor reviews of the thoughts and practices of the exploration com-munity. Accordingly, we have invited seven leading authorities to contribute papers dealing with specialized aspects of this field.Exploration is a science, or art if you will, that is constantly changing in keeping with our expanding knowledge of geology and technology. It started with the old-time prospectors who searched the wilds for exposures of ore, and made finds that developed into some of our most important mining camps. As more discoveries were made, they were able to relate certain types of deposits with particular geological conditions, laying the foundation for modern concepts of economic geology. The mapping by the early field parties lacked detail and usually served to outline the ""greenstone"" areas considered favourable for prospecting. More de-tailed studies through the years by government and company geologists led to new thoughts on the origin, emplacement and geological control of orebodies. The continuing diversity of opinion on these subjects indicates a need for further research, but each year sees an increase in our reserves of factual information."

Jan 1, 1967

Reaction between xanthate ions in solution and oxidized compounds present on the surface of galena to form lead xanthate is considered to be a side reaction not contributing to flotation, although accounting for some consumption of reagent. The direct reaction of lead sulphide with xanthate and oxygen to form lead xanthate is the most significant to flotation. Coadsorntion of dixanthogen is also involved. Previous work has shown lead recovery in lead rougher flotation to be a function of m [H+] where: m = concentration of xanthate in solution rHl = hydrogen ion concentration. A plausible explanation for this relationship is suggest-ed. Likewise, the experimental findings that the amount of xanthate adsorbed under certain conditions is a function of m'[H+] are explained in terms of reaction between xanthate ions and soluble basic lead salts such as PbO.PbS04? It is also shown that m[H+] should have a constant value in lead cleaners operating at a higher pH than the roughers. This conclusion is confirmed by plant data, and the value of the constant agrees well with the calculated value. The finding is useful in mill control.

Jan 1, 1965

By D. Zagidulin

Short term electrodeposition experiments (up to 80 min.) at two current densities 220 and 275 A/m2 with varying concentrations of thiourea and glue were performed to determine the optimum levels of glue, thiourea and current density for industrial copper electrorefining. White Light Interference Microscopy was used to acquire digital images of the morphology of the electrodeposited copper. Scaling analysis was employed to pa-rameterize the morphological information encoded in the images. The limiting rough¬ness, *, the critical scaling length, Lc, and the aspect ratio, 4*/ Lc, were determined as a function of the deposition time and the amount of organic additives. These parameters were used to calculate the dynamic exponent, B, the roughness exponent, 1/z, and the as¬pect ratio exponent, y, plotted as a function of glue and thiourea concentrations. These 3D plots allowed us to find conditions corresponding to the minimum of B and y, at which the deposited copper is characterized by a small roughness and a dense structure.

Jan 1, 2007