Search Documents

By Lawrence Melis

Fission Uranium Corp.’s Triple R Uranium Deposit at its Patterson Lake South Project is located in northwest Saskatchewan in Canada’s Athabasca Basin. As part of pre-feasibility studies for the project a detailed metallurgical test program was completed to provide process design criteria. The testwork program encompassed preparation and analysis of test composites, comminution testing, uranium acid leaching, liquid-solid separation, solvent extraction of uranium, precipitation of uranium yellowcake products, tailings and effluent treatment, tailings physical and chemical characterization, and environmental testing of prepared tailings, as well as investigations of gold and silver recovery from the mineralization. The paper provides mineralogical information, testwork methodologies and test results which were used to arrive at process design criteria and the selection of the process flowsheet for the project.

Jan 1, 2020

By T. L. Tanton

"The New Helen mine is 12 miles east of Michipicoten harbour on lake Superior. It is 2 miles east of Wawa station, on the Algoma Central railway, with which it is connected by a spur line railway and a highway.The mine was discovered by Ben Boyer in 1898 during the gold rush near Wawa lake, Ontario. The original discovery was of solid hematite ore extending to a height of 100 feet on a hill rising abruptly on the east side of Boyer lake. The property was acquired by the Algoma Steel Corporation and mining was commenced in 1899. The first iron ore was shipped in 1900. The mine was operated until 1918 when the hematite became exhausted at a depth of 800 feet below Boyer Lake level.Drilling at the Helen mine, after 1910, revealed a large body of siderite both below and to the east of the hematite. By 1913, the body was known to be about 200 feet wide, 3,000 feet long, and at least 2,200 feet deep. In this there was estimated to be 100,000,000 tons of proved and probable siderite ore. An adit was driven into this body in 1917, and in 1918 work was suspended. In 1937 the Algoma Steel Corporation proceeded with the development of the New Helen mine by open-cut mining, and the beneficiation of the ore by sintering. Production commenced in 1939 and has since been maintained at the rate of approximately 500,000 tons a year.From 1900 to 1918, inclusive, the total production from the Helen mine was 2,823,369 tons of hematite ore and 51,930 tons of pyrite. From 1939 to the end of 1945 the total production from the New Helen mine was 3,921,455 gross tons of siderite ore.GEOLOGYThe Helen property is underlain by rocks of Precambrian age. For general description, and a statement on the structure of the iron deposits, the map-units are those shown in Fig. 1.The oldest rocks occur in a complex that lies north and south of an east-west trending zone, 1 ½ miles long and ¼ mile wide, in which the iron deposits occur. That part of the complex lying south of the iron deposits includes small masses of altered conglomerate and slate, and greenstones and pyroclastics. Other fairly abundant rocks are sericitic, chloritic, ottrelitic, and carbonatized schists of doubtful origin, and almost massive metamorphic rocks in which a development of carbonate, ottrelite, quartz, and other minerals has obscured a pre-existing schistose structure. Felsite and quartz porphyry are· prominently exposed south of the iron deposits."

Jan 1, 1954

By D. J. Xue

Four kinds of coal-rock combination were subjected to three kinds of stress waves in the SHPB numerical simulation. The wave propagation and the changes of the strain energy in the coal-rock combination during the dynamic impact process were recorded as well as the contact force. The dynamic response law of coal-rock combination was obtained. It was found that the coal had better reflectivity than the rock because of coal with larger impedance. In contrast the rock had better transmissivity. As the crest value of the incident wave increased, the increment in the crest value of the transmitted wave weakened in the coal-coal group, coal-rock group and rock-coal group, in contrast, the increment in the rock-rock group increased.

Aug 1, 2013

By Nav Dhadli

Tailings from Oil Sands MiningWhat are they? Challenges Solutions Regulatory Environment Definition of the AFD Tailings Treatment Process 2010 AFD Pilot/Demonstration ProgramTechnical challenges Performance and Results Next steps Oil Sands Industry Collaboration on Tailings Technology TAILINGS ?WHAT ARE THEY? Mixture of remaining water and solids following bitumen extraction process Composed of water, sand, silt, clay, small amounts of hydrocarbon (bitumen, solvent, and asphaltenes) A necessary part of production in excavation of oil sands and removal of bitumen

May 1, 2011

By Q. G. Reynolds, R. T. Jones

"Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. A mathematical description is presented for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are shown to have a significant effect on the residence time distribution.INTRODUCTIONThere are some processes in which the time spent by the feed material in a smelting furnace plays a significant role in determining the extent of the reactions between metal and slag and influences the degree of settling of metal droplets from a molten slag.Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. Here we will focus on producing a mathematical description for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are studied.Previous work (Jones, la Grange and Assis, 1997) has studied the effect of retention time on the degree of cobalt recovery achieved in a slag reduction process. In that work, a method was proposed for the calculation of the mean residence time of the contents of a pilot-plant furnace. That approach is to be extended here for the purposes of providing a more general design or scale-up tool.The maximum allowable depth of molten material in a given furnace is affected by such factors as the desired batch size (or the size of the ladles) and the pressure of the molten material that the tap-hole and surrounding system can withstand. Within these constraints, there might be some scope for choice of taphole position. The effects of this choice need to be understood mathematically."

Jan 1, 2012

By Albert G. Zima

THE conservation of strategic materials during war rime gives rise to many problems not commonly encountered in times of peace. During normal times, when world trade is unrestricted, we are apt to become lavish to a point of extravagance in our use of those materials which, during rime of war, become scarce owing to inadequate transportation and production facilities or because the enemy may be in position to control sources of supply. It becomes necessary, then, to enforce rationing of available sup-plies, and in some cases, where such supplies are wholly inadequate, we find we must resort to the use of substitute materials. We are now confronted with such a problem to an extent never before experienced, with the result that many of the commodities upon which our civilization depended are now either shut off completely or, because of the heavy demand occasioned by war production, are not available in sufficient quantities to meet requirements predicated on peace-time standards and manufacturing methods. It has become necessary, therefore, to make many changes, some of them very drastic indeed, to enable us to carry on our war effort effectively. This? discussion will deal briefly with one phase of this problem, namely, the conservation of alloys required in the making of steels necessary for war production. In line with a request from the War Production Board, the Technical Committee on Alloy Steels of the American Iron and Steel Institute made a study of experimental steels embodying the !east amount of alloying constituents, with the objective in mind of substituting these steels wherever possible for the standard alloy steels used heretofore. This study embraced the following phases: (1) The availability of silicon and manganese; (2) The average quantity of alloying elements recoverable from scrap; (3) The effect of increases in manganese and silicon contents on the general properties of steel; ( 4) The elements and ranges of elements which might be used to duplicate the hardenability of the steels now in use; (5) The effect of combining several elements in small quantities upon the properties of steel at various hardness and strength levels; (6) A determination as to whether or not the steels selected would suffice for general application. Working on this basis, the Committee arranged for the manufacture of several heats of steels containing various combinations of different amounts of such elements as silicon, manganese, chromium, nickel, and molybdenum. The steels thus produced were compared by hardenability tests.

Jan 1, 1943

By Bai-ru Xia, Cang-qin Jia, Qi-wu Huang

Limit Analysis Theorems has revealed to be a powerful tool for the development of numerical models aiming the determination of the load bearing capacity of structures reached by plastic collapse. This work presents a numerical formulation for the computation of strict upper bounds of the collapse loads of rigid-perfectly plastic mechanical systems, derived within the kinematical theorem framework. A key advance of this present method is that the problem is described only in terms of nodes and discontinuities connecting those nodes rather than element or bodies. The alternative approximation procedure to the traditional finite element method might involve discretization of a given body using a suitably large number of nodes laid out on a grid, with the failure mechanism comprising the most critical subset of potential discontinuities interconnecting these nodes. Potential discontinuities which interlink nodes laid out across the problem domain are permitted to crossover one another, giving a much wider search space than when such discontinuities are located only at the edges of finite elements of fixed topology. Highly efficient interior point method solvers can be employed when certain popular failure criteria are specified (e.g. Mohr-Coulomb). By adopting this processing approach it is possible to solve very large problems which normally exceed the memory capacities of a single computer. The developed numerical tool reveals to be robust and versatile, able to solve a wide range of 2D problems. Velocity singularities are automatically identified and visual interpretation of the output is straightforward. Several numerical examples including rock slope are studied by the new method, and the results are very close to those calculated by using analytical method and FEM.

Jan 1, 2015

By V. Bondarenko

The importance and necessity of gas hydrates deposits development followed by natural gas extraction is considered in the present paper. Analysis is given to world sources focused on methane hydrates formation conditions. Information covering the most perspective gas hydrate deposit of the Black Sea is presented in the article. Two most common methods of gas hydrates development ? thermo stimulation and inhibitor injection are analyzed presenting their comparative characteristics. Basic scientific trends and developments of underground mining department in the field of gas methane extraction from gas hydrates are scrutinized. Schemes and methods of natural gas hydrates development are shown together with formulas, parameters and factors influencing the extraction process. Also the analysis is given to the possibility of gas hydrates formation from methane-air mixtures of degassing wells from coal mines of Ukraine. Improved experimental unit for gas hydrates formation under laboratorial conditions is presented with its basic characteristics. General conclusions and basic tasks requiring further research are given in the end.

Aug 1, 2013

By A. Bowles

The process of accumulative roll bonding (ARB) has been applied to wrought magnesium alloy AZ31. Accumulative roll bonding results in severe plastic deformation of sheet material. In AZ31, this process leads to the refinement of the microstructure by dynamic recrystallization. The refinement of the microstructure results in an improvement in mechanical properties with potential for producing materials for superplastic forming. In this work AZ31 was bonded with up to 64 layers and the potential of roll cladding with aluminium was also investigated. The development of microstructure and the mechanical properties are reported here.

Jan 1, 2006

By Eric R. Skonberg

"Technology exists today to blind drill a mine shaft 20 feet in diameter, unlined, over 3,000 feet deep. These shafts must be lined in the most economical, safe and expedient manner possible. A new technique of stacking precast concrete cylindrical sections in the unlined shaft has been developed to yield a dry and hydrostatically lined shaft .These sections must withstand an external radial pressure of 3,000 feet of water yet take up as little room as possible in the shaft . Using high-strength concrete, wall thicknesses may be kept at 2 feet. The outside diameter of the sections has been chosen to be 18 feet to allow for some annular space between the liner and shaft wall. The concrete sections are produced in segments 10 feet long weighing 75 tons each. During drilling operations, the concrete sections are cast and cured. After drilling operations are complete, a headframe is situated over the shaft. The unlined shaft remains full of fluid. A special liner running tool is mated with the section in three steel ports at the bottom of the section. The section and running tool are lowered into the hole, and the tool is disconnected and returned to the surface. Subsequent sections are lowered and stacked using the same operation. Grout is placed behind the liner to result in a dry shaft."

Jan 1, 1981

By C E. Gordon Brown

Aircraft utilization, weather and cost data are given for three separate projects north of the sixtieth parallel in the Northwest Territories and the Yukon Territory. These operations, carried out by helicopter-equipped geological and prospecting parties, have cost $24 to $30 per square mile, depending principally on the distance from the base. They provide adequate surface exploration of areas with 40 to 50 per cent rock outcrop. A good one-inch-to-one-mile geological map can be made. T HE exploration of the Canadian northland has been given increasing attention by the mining industry during recent years. In many cases, the initial problem is to make an adequate reconnaissance of a large area where existing geological information is meagre. The Geological Survey of Canada pioneered the use of helicopter-equipped geological parties for mapping at a scale of eight miles to the inch.

Jan 1, 1964

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy's resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By G. W. Poling

Sedimentation behaviour of siliceous mill tailings derived from a magnetite-chalcopyrite ore in fresh water, fresh water - sea water mixtures and full-salinity sea waters are compared. Results of batch settling tests are presented in the form of settling curves and solids flux curves. The addition of a few per cent of sea water markedly enhanced the zone sedimentation rate due to particle agglomeration caused by a reduction in zeta potential of the suspended solids. The presence of a small amount of residual, previously magnetized magnetite in the tailings also enhanced agglomeration and sedimentation. The significance of these results to submarine disposal of mill tailings is discussed.

Jan 1, 1973

By S. Bhattacharjee

"Rock failure process is generally recorded or measured using conventional sensors like strain gauges, seismic, micro-seismic, acoustic, electromagnetic and other techniques. The above sensors are either to be pasted on the surface of the rock sample or placed very near to it to capture the response of the sample with the increment of load. This requires precise tools to cut or polish the locations where sensors are to be placed. Moreover, deformation or acoustic or micro-seismic activities are recorded only at the locations where sensors are pasted.Recent development in Digital Image Correlation (DIC) technique has shown promise to measure deformation / strain at every location of the surface of a sample. In DIC, two images (reference and deformed) are taken within a small time interval of the same object are compared to estimate the change in reflectance as a function of displacement, velocity or rate of strain at each pixel while the object is undergoing through a loading process. In this study, extended digital image correlation (X-DIC) technique has been implemented using 4-noded quadrilateral elements with a discontinuity surface in the deformed image. The continuous and enriched displacements are estimated at each node.The X-DIC method is verified using numerically generated images. The study has been further extended to evaluate the performance of X-DIC method on deformation analysis of experimental samples under uni-axial loading condition. The results of this study show that X-DIC method is an effective tool for determination of displacements of the entire surface of a rock sample having a discrete crack or discontinuity in a non-contact manner. This method demonstrates the applicability to investigate rock failure mechanism for the entire sample in a laboratory set up as well as monitoring of pillar failure mechanism in underground mines."

Jan 1, 2015

By T. R. Kostecki, K. V. Jessu

"Roof bolts are subjected to axial stresses, shear stresses, or both. Axial and shear stresses were compared between roof bolts machined with two and three slots. Shear stresses perpendicular to and at an angle to the shear planes were evaluated by analyzing a three-slot instrumented roof bolt, performing laboratory tests on two- and three-slot roof bolts, and conducting in-situ test analyses. Threeslot bolts appear to provide a complete bending strain profile, requiring no prior knowledge of the estimated shear-plane orientation. Minimum displacements occur in roof bolts installed perpendicular to rather than at an angle to the shear planes.RÉSUMÉ Les boulons d’ancrage dans le toit d’une mine sont sujets à des contraintes axiales, des contraintes de cisaillement ou les deux. On a comparé les contraintes axiales et de cisaillement de boulons d’ancrage usinés avec deux ou trois fentes. Les contraintes de cisaillement perpendiculaires et à angle aux plans de cisaillement ont été évaluées en analysant un boulon d’ancrage de toit à trois fentes, en effectuant des essais en laboratoire sur des boulons d’ancrage de toit à deux et à trois fentes et en effectuant des analyses de tests in situ. Les boulons à trois fentes semblent fournir un profil complet de résistance aux contraintes de flexion, sans avoir besoin de connaître l’orientation estimée du plan de cisaillement. Des déplacements minimums ont lieu dans les boulons d’ancrage de toit installés perpendiculairement, plutôt qu’à un angle, aux plans de cisaillement."

Jan 1, 2016

By M. Tanaka, T. Oishi, K. Koyama, S. Alam

"A novel hydrometallurgical process for copper recovery from waste printed circuit boards has been proposed, which consists of selective leaching of copper metal as Cu(I) by Cu(II) in ammoniacal alkaline solution, purification, and electrowinning. The distinct feature of this process is much lower power consumption during the electrowinning than that during the conventional one from acidic copper sulfate media, because the deposition of copper metal from Cu(I) at the cathode and the oxidation of Cu(I) to Cu(II) at the anode take place in the present method. In the laboratory-scale tests using waste printed circuit boards, high purity copper which contains 1.1ppm of impurities was obtained in a chloride system. INTRODUCTIONThe recovery of various metals from waste materials is an important issue in order to conserve the environment and metal resources. Copper is used for cables, electric appliances, etc., and is currently a very important material for industries and will continue to be in the future. Among the wastes that contain copper, one of the most complex recycling materials is electronic scrap like printed circuit boards (PCB), which generally contain 10-30% copper as well as plastics, fibreglass and other metals. There are two ways to recover copper, either pyrometallurgical or hydrometallurgical. Hydrometallurgical treatments generally have more flexibilities in the process scale and control. The separation processes tend to become complicated because of the poor selectivity during the leaching in the sulphuric and hydrochloric acid media. On the other hand, the use of ammonia as a complexing agent, gave a higher selectivity for copper leaching (Nigo, Majima, Hirato, Awakura, & Iwai, 1993; Majima, Nigo, Hirato, Awakura, & Iwai, 1993; Zhou, Shinme, & Anezaki, 1995; Koyama, Tanaka, & Lee, 2006) .In this study, recycling process containing leaching, copper deposition at a cathode and oxidation of copper(I) at an anode from ammoniacal alkaline solutions containing Cu(I) or Cu(II) is introduced. Furthermore, copper recovery from a waste printed circuit boards and impurity behaviour was examined in ammonia-ammonium sulfate (sulfate system) and ammonia-ammonium chloride (chloride system) systems."

Jan 1, 2012

By M. Abumiya, N. Onodera

"The synthesis of large scorodite particles in non-ferrous metallurgical industries usually requires a high-cost operation involving heating and high-pressure autoclaving. To overcome these obstacles, an atmospheric-pressure process for scorodite synthesis (DMSP®) was developed, in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. This process gives scorodite of good crystallinity with particle sizes as large as 15-20 µm. The solutions used for scorodite synthesis in the DMSP® are prepared from various residues containing arsenic from non-ferrous smelters. The solutions may be contaminated with Cu, Sb, and Bi, for example, and therefore the effects of such impurities on the formation of crystalline scorodite need to be investigated. In this study, the effects of Cu, Sb, and Bi contaminants on the formation behaviors of scorodite particles in the DMSP® were investigated systematically.INTRODUCTIONThe synthesis of crystalline scorodite (FeAsO4·2H2O) is a suitable method for arsenic (As) stabilization and storage of As-containing by-products such as flue gas dusts in non-ferrous smelters. It is expected that the formation of large, highly-crystalline scorodite particles would be an ideal method for avoiding the release of arsenic to the environment. Generally, autoclave methods under pressurized oxidation conditions at temperatures above 100°C have been used for the formation of arsenic minerals such as scorodite. However, the autoclave method requires sealed vessels that are resistant to high pressure, heat and acids. This process is also unfavorable on account of the high construction expenses, and high running costs as a result of vapor heat loss. Processes for synthesizing scorodite under atmospheric conditions at temperatures below 100°C which do not need an autoclave have therefore been extensively investigated (Demopoulos, Droppert, & VanWeert, 1994; Demopoulos, 1996; Demopoulos, Lagno, Wang, & Singhania, 2003; Droppert, Demopoulos, & Harris, 1996; Filippou & Demopoulos, 1997).Recently, Fujita et al. (Fujita, Taguchi, Abumiya, Matsumoto, Shibata, & Nakamura, 2008a, 2008b, 2009; Fujita, Taguchi, Kubo, Shibata, & Nakamura, 2009; Fujita, Taguchi, Shibata, & Nakamura, 2009) developed a new method for producing large scorodite crystalline particles with improved filtration and washability properties at normal atmospheric pressure and temperatures below 100°C. In the new method, oxygen gas (O2) is blown into solutions containing a high concentration of arsenic ions (As(V)) and ferrous ions (Fe(II)). The Fe(II) ions were subsequently oxidized to ferric ions (Fe(III)), resulting in the formation of large scorodite particles. High supersaturation of solutes such as Fe(III) will result in excessive nucleation, and the formation of poorly crystalline phases. The scorodite formation must therefore be conducted in a manner that avoids the critical supersaturation level being exceeded. It is supposed that the oxidation of Fe(II) to Fe(III) by O2 gas in the new method suppressed the supersaturation of Fe(III) during scorodite formation. The low Fe(III) supersaturation resulted in formations of highly crystalline scorodite particles of size of around 20 µm. In June 2008, based on the developed process described above, DOWA began experiments to verify the industrial capability of a plant with a capacity of 30 MT/month of As. It was successfully proven that it is possible to produce crystalline scorodite industrially on a commercial scale. This process was named and trademarked as DMSP® (Kubo, Abumiya, & Matsumoto, 2010)."

Jan 1, 2012

By S. Parent, J. -F. Lepage, S. Glover

"Goldcorp – Eleonore’s 7 000 tonnes per day gold mill was started up in October 2014 and achieved commercial production in April 2015. During the first year, operation has faced challenges from grinding, flotation, sulfide cyanidation and tailing filtration to achieve targeted throughput, availability and recovery.The optimization of non-sulfide tails filter cloth lifetime and filter press availability had the most significant impact on ramp-up of both mill throughput and availability. A change in steel ball addition size to the grinding circuit was made to meet the targeted p80 of 65 µm. Various optimization efforts were conducted on the flotation circuit, intended to recover all sulfide-bearing minerals. The goal is to attain the environmental target of 0.12% sulfur in flotation tails (to eliminate acid mine drainage or AMD), while an average of 0.31% sulfur was obtained over the first months of 2015. Collectors, frothers, activators and hydrodynamic parameters were tested to improve the circuit desulfurization efficiency. High sulfide reactivity in pre-oxidation and cyanidation severely impacted dissolved oxygen levels and cyanide consumption. Studies were undertaken to understand the effects of mineralogy, grind size and leach conditions on gold dissolution kinetics and cyanide consumption. Efforts were focused on pre-oxidation to restore dissolved oxygen levels as well as optimizing both lead nitrate addition and pre-oxidation time.INTRODUCTIONGoldcorp Eleonore’s mill commissioning started in September 2014. It was considered to operate the mill at 3 500 tpd during design, as the mine was planning to operate at this throughput for the first year. However, with the stockpile of ore and a higher throughput from the mine, the mill was able to run at higher tonnage than initially anticipated.While increasing tonnage, a few bottlenecks were discovered and overcome in areas such as filtration and cyanide destruction. There were also recovery issues which were addressed in areas such as grind and sulfide leach. This paper focusses on the first complete year of operation ending September 30th 2015. A process description and the flowsheet are presented below and it will then go into detail about operational, metallurgical, mechanical and design issues experienced during the year."

Jan 1, 2016

By Leonard L. Fischman

It is important to define "adequacy," and the most useful definition is a continuing availability of mineral materials under cost and other conditions which imply no significant burden on the achievement of otherwise attainable levels of consumption and well-being. For current decision making, it is sufficient to consider adequacy just to the end of the century, with some regard being given to then remaining mineral inventory. A comparison of cumulative demand projections to the year 2000 with already identified reserves ( economically recoverable amounts in known deposits) suggests little reason for concern with world adequacy of iron ore, aluminum, manganese, chromium or potash. Conservative estimates of "prospective" reserves (amounts producible at today's prices, but yet to be discovered) suggests that there are ample quantities of virtually all other mineral resources as well. A probable exception is oil and gas, of which there may be scant amounts remaining after the turn of the century. However, there is an evident sufficiency of substitute forms of energy, though it is difficult to see just where developing technology will take us. The critical questions have to do with the increasing dependence of the industrialized countries on external sources of supply , coupled with a new international politic s which complicates the problem of insuring timely development of, and access to, remaining deposits. In this context, Canada, a still mineral-rich nation, is in one of the more favorable positions.

Jan 1, 1977

"Dry crushing trials at pilot scale have shown that the IMPTEC Super-fine Crusher has the capacity to generate ultra-fine products from hard mineral assemblages presenting at either coarse or fine feed sizes. The super-fine crusher was introduced at the 27th International Mineral Processing Congress in Santiago Chile, with results from a range of duties, which demonstrated the crusher’s potentially expansive operating scope. This paper focuses on current preparations to progress the technology from pilot scale to commercial scale within a concrete production plant, where lead blast furnace slag will be crushed to ultrafine sizes to generate an active silica product for use as a supplementary cementitious material, which can replace Ordinary Portland Cement. A key objective of the operation is to demonstrate an economical route to reducing the cost of concrete production, improving concrete quality and reducing greenhouse gas emissions. The paper also highlights the potentially key contribution super-fine crushing can make to the long-term viability of iron ore beneficiation by simplifying comminution flow-sheets and reducing operating costs. There is every indication that the technology has the potential to feature universally in metalliferous and industrial mineral flow-sheets. INTRODUCTIONToday’s IMPTEC super-fine crusher is the successful end product of development work over 19 years and is the third particle size reduction device conceived, built and tested over that time. The concept evolved as engineering design progressively developed a mechanism capable of harnessing a highly efficient combination of fundamental particle breakage mechanisms. Early development trials at pilot scale indicated that super-fine crushing had the potential to establish a wet or dry, media free, low energy route to ultra- fine products from hard mineral assemblages. Having achieved some impressive results from open circuit pilot tests on fly ash and granulated blast furnace slag it became clear that the cement industry may well provide opportunities to apply the technology commercially. Following expressions of interest from local cement and concrete plant operators, IMPTEC negotiated an agreement to undertake commercial trials with a SFC 350 super-fine crusher installed on site at a concrete supply plant in South Australia. Super-fine crushing scope was recently expanded following further expressions of interest from research groups involved in the processing of iron ores. Pilot trials are progressing in these areas."

Jan 1, 2016