Search Documents

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the RISKGATE body of knowledge captured specifically for the management of unwanted events that stem from the handling and use of explosives (drill and blast) within surface coal mining operations. The knowledge presented is divided into a series of initiating events (listed below) within which there are further degrees of classification based on design, operation, and management concerns. Initiating events: ? Loss of control of explosives and associated chemicals in storage on site ? Loss of control of explosives and associated chemicals during transport ? Loss of control of explosives and associated chemicals during manufacture ? Loss of control of explosives and associated chemicals during handling and blast operations ? Loss of control of explosives and associated chemicals during disposal The system guides the user in generating substantive and leading-edge controls to assist in the design, management and reporting of drill and blast operations to meet stringent internal and external requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013

By G. Tairova, J. Ioffe

Arsenic, selenium and mercury species are common contaminants in mining aqueous streams and present significant environmental and health problems. The objective of this project is to investigate methods to lower the concentrations of these elements in mining aqueous streams. A new composite media for removal of these elements of concern from mining effluents was developed. The results of bench scale and pilot plant experiments, using the media, indicated removal of arsenic, selenium, mercury and other elements of concern below detection limits.

Jan 1, 2014

By JOHN H. HUDSON

Ceramic clays of the Prairie Provinces range in age from Lower Cretaceous to Pleistocene and Recent. Two significant ceramic clay horizons are the Paleocene Willo wbunch Member of the Ravenscrag Formation in Southern Saskatchewan and the Upper Cretaceous Whitemud Formation, which is found in Saskatchewan and Alberta. The Willowbunch Member is worked at one locale in Saskatchewan; the Whitemud Formation is worked at several locales in Saskatchewan and Alberta. Bentonite operations are found at Morden in Manitoba, Rosalind and Onoway in Alberta, and Wilcox in Saskatchewan.

Jan 1, 1984

By M. El Tokhi, H. Arman, B. M. Amin

"This paper aims to overview some mechanical and physical features of the gabbroic rocks. The study has two phases: filed study/in-situ measurements and laboratory work. During the field studies, rock block samples were collected from different locations of the study area to represent the different types of the gabbroic rocks. Either core or rock samples for various tests were prepared from rock samples taken to the laboratory. The unconfined compressive strength (UCS), indirect tensile strength (ITS), point load index (PLI), Schmidth hammer rebound value (SHV), slake durability index (SDI), sonic velocity (SV) and unit weight (UW) test were carried out either on the selected rock block samples or core samples.INTRODUCTIONThe geology of the United Arab Emirates (UAE) has been divided into three major rock units (Lippard et al., 1986); an autochthonous succession, allochthonous units composed mainly of Mesozoic rocks and include the Sumeini Group (concomittent slope sediments), Hawasina Complex (basinal sediments) and the Semail ophiolite nappe (massive slice of former oceanic crust), that were emplaced as a series of thrust nappe in the Late Cretaceous and Neo-autochthonous sequence of Maastrichtian and Lower Tertiary sediments.The Semail Ophiolite (600 km long and up to 150 km wide) is thought by some authors (Glennie et al., 1990) to have been generated along a subduction related back-arc spreading axis during the Cenomanian-Turonian and was obducted onto the Arabian continental margin during the Campanian. Others, however, consider it to represent a primitive arc-spreading center related to oblique subduction Lippard et al., 1986). The Ophiolitic rocks in the study area comprise mantle and crustal sequences. The mantle peridotite and crustal gabbros are the dominant rock types of the exposed Semail Ophiolite north of the Hatta zone. This paper is only concentrated on the gabbroic rocks."

Jan 1, 2015

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By Paul-Henri Girard

La Mine Agnico-Eagle division Laronde situé à Cadillac, est un producteur d?or, d?argent, de cuivre et de zinc. Cette propriété est situé dans les cantons Bousquet-Cadillac le long d?une des ceintures géologiques les plus productives au monde. La mine Laronde a débuté la production en octobre 1988 à un rythme de 1360 tonnes par jour. Ensuite, elle a augmenté son rythme de production successivement à 1800 TPJ en 1990, 3300 TPJ en janvier 2000 et 4500 TPJ en octobre 2000. Agnico-Eagle, fondé par feu Paul Penna, a toujours eu comme politique la participation des employés aux décisions de la compagnie pour le déveleppement de celle-ci. Cet écrit va permettre de mieux comprendre la façon dont la division fût développé.

May 1, 2001

By G. E. Agar, W. B. Kipkie

"This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady state balance can be calculated for a circuit.Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative tec1nique to arrive at the steady state balance. The program is written so that a variety of circuits can readily be simulated.A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets is presented on sulfide ores, on copper-nickel separation and on silver flotation,"

Jan 1, 1978

By Behzad Vaziri Hassas, Firat Karakas, Esra Tanisali, Mehmet S. Çelik, Ahmad Hassanzadeh

Coagulation is basically an aggregation process where particles settle under the influence of interfacial forces with electrostatic forces playing a governing role. Although particle morphology consisting of shape and roughness dictates the physical encounter of two particles, their eventual coagulation is not only influenced by columbic forces but also other interfacial forces such as hydrophobic interaction, which affects the extent of aggregation of particles through increasing the distance of interaction. Roughness is well known to increase the effective contact angle on hydrophobic surfaces and also enhance interfacial forces. In this study, the effect of morphology of particles and particularly roughness on the settling velocity and in turn coagulation tendency was investigated. Batch settling tests (BSTs) of different particle morphologies were investigated as a function of pH. Two different morphologies of silica particles were utilized with the same particle size distribution (PSD) including smooth-spherical and rough-spherical (Etched). Rough particles were prepared by acid etching technique using hydrofluoric (HF) at different time intervals (15-300 sec). Etched samples were identified and quantified by optic profilometry. Settling test results showed that the settling velocity of particles in a suspension of 2% solids in the massive settling region is significantly affected by particle morphology of the suspension. Coagulation results further revealed that aggregation of rough particles is faster than smooth-spherical particles. Coagulation results are elucidated on the basis of particle morphology and its effect on distance of separation through hydrophobic forces.

Jan 1, 2016

By Richard W. Lawrence, Richard Poulin

"Numerous processes co-exist for metal extraction and for metal removal from effluents of mining operations. Each process enjoys an economic advantage, including environmental cost and benefit, if utilized in a specific situation. This applies equally to biohydrometallurgical processes. This paper will analyze four types of biohydrometallurgical processes for their economic and environmental attributes: biooxidation of refractory gold, extraction of copper from sulfide, metal removal from effluents by active sulfate reduction, and metal removal by the use of wetlands. By examining the economic and environmental advantages of these processes, generalizations can formalized and it becomes possible to define niches of application where biohydrometallurgy can be considered. Our analysis shows that biohydrometallurgy can be efficient at small scale, be more environmentally friendly than conventional technologies and is relatively easier to operate. The higher financial risk associated with unproven technologies at the commercial scale is being eliminated as biotechnology-based plants are put into production.IntroductionBiotechnology can be described as the rational exploitation of the activities of living cells or parts thereof, requiring an integrated multidisciplinary approach between biological and technical disciplines. Microbiology, biochemistry, botany, molecular biology, chemistry and engineering all contribute to practical applications in the extraction, manufacturing and service industries, and in environmental management. Considerable commercial success of biotechnology has been achieved in several sectors, including health care, agriculture, forestry and aquaculture.Over the past 40 years, industry, research organizations, government laboratories, and universities in a large number of countries have participated in investigating the utilization of biotechnology applications in mining. Today, several technologies are used commercially in well understood and engineered systems which can be grouped under the term biohydrometallurgy. Many more technologies have been demonstrated at laboratory or pilot plant scale. Although initial developments and commercial applications were aimed at metal extraction, the dramatic increase in environmental awareness, the practice of sound environmental management demanded by more stringent regulations over the past decade, and the need for low cost treatment in perpetuity, has led to serious investigation of biotechnology for environmental control. In addition, increasing power costs, lowering of ore grades, and decreasing commodity price in real dollar terms require the use of highly efficient and competitive extractive technologies."

Jan 1, 1998

By D. Michaud, C. Bazin, S. Lévesque, L. Pérez-Barnuevo, H. Longuepée

In recent years, with the emergence of Geometallurgy, a great effort has been made to characterize ore resources as early and accurately as possible, to allow better design and a more efficient operation of mineral processing circuits. In this context, core logging plays an important role, since drill cores provide the first insight into the ore characteristics. However, to satisfy geometallurgical requirements, traditional core logging does not suffice. New tools and methodologies need to be developed for the automation of core logging and the acquisition of mineralogical data better related to mineral processing performances. In this paper, a methodology for the geometallurgical characterization of drill cores is proposed, based on the drill core textural patterns. Textural pattern is defined here as the macroscopic spatial arrangement of minerals. The Mont-Wright iron ore deposit (Quebec, Canada) is used as a case study. The first part of this work aimed at analyzing the potential link between the iron ores textural patterns observed in drill cores and their response to ore processing, namely comminution and concentration. Preliminary results show similar performances in terms of energy consumption and heavy liquid separation for samples showing the same textural pattern. In the second part, this work seeks to develop a methodology for the automated identification of drill core textural patterns by the application of digital image analysis and discriminant function analysis. The results obtained show that this methodology is able to discriminate between the textural patterns identified at Mont-Wright with a good rate of success. Therefore, this work lays the foundation for the development of a new drill core characterization tool, which would allow for the early prediction of the iron ore behaviour during mineral processing through the identification of drill core textural patterns.

Jan 1, 2016

By R. T. Seaman

There are several hydrometallurgical alternative processing options under development for high enargite and arsenic containing copper concentrates ranging from biological, atmospheric, medium temperature oxidation to total oxidative leaching. The most developed of these options is the CESL process boasting pilot campaigns totaling more than 8760 hours of fully integrated continuous operation, as well as, over two thousand batch scale oxidation tests performed on dozens of concentrates for flowsheet development. This paper reports the observed deportment of arsenic under varying arsenic, iron and acid oxidation conditions; it also describes the impact of iron to arsenic ratios and residue recycle on overall arsenic behavior and its stability in residue. INTRODUCTION The CESL Hydrometallurgical Process (CESL) was originally developed to compete with smelting of clean chalcopyrite concentrates. High Treatment Charges and Refining Charges (TC/RCs) combined with premiums on London Metal Exchange (LME) grade copper from onsite refining made treatment of copper concentrates using CESL a viable option at the time. As world demand for copper increased and a subsidized Chinese refining market developed, smelting contracts became more favourable for the miner and focus was placed on modifying the CESL Hydrometallurgical Process to handle concentrates with elevated deleterious elements. Dozens of pilot campaigns processing concentrates containing elevated concentrations of uranium, fluoride, mercury and nickel all led to further developments of the CESL Hydrometallurgical Process. In 2016 a United States patent was granted for a novel modification of the CESL Hydrometallurgical Process for recovery of copper from arsenic-bearing and/or antimony-bearing copper sulphide concentrates, Henry Salomon de Friedberg (2016). To date, over 2000 bench scale tests along with five fully integrated closed loop pilot campaigns, totaling over a year of online operation time, have been conducted processing arsenic bearing copper concentrates. This paper summarizes the observed behavior of arsenic under varying autoclave and process conditions.

Jan 1, 2019

By Sarah R. Hindle

Carbon capture and storage has jumped to the forefront of climate change mitigation efforts for its capacity to sequester large amounts of carbon. Mineral carbonation is one prominent option, mimicking and accelerating the natural weathering process of certain silicate minerals. This has the ability to produce stable carbonate minerals that can store carbon on geologic time scales with little to no risk of leakage. Commercialization of this process is ideally suited for integration into the proposed mining operations at the Turnagain Nickel site in Northern BC. This is due to the abundant supply of suitable ultramafic feedstock material, as well as the economic benefit of sharing costs while reducing net emissions and bringing value to otherwise valueless and costly waste rock. While studies have shown this process to be technologically viable on a laboratory scale, assessing the economic and financial viability of such a process on an industrial scale is necessary. An evaluation of the financial feasibility of integrating mineral carbonation into the mining cycle at Turnagain under a proposed cap-and-trade system is presented.

May 1, 2010

By B. S. W. Buffam

"The property of Moneta Porcupine Mines, Limited, consists of a group of eight claims in Tisdale township, Ontario. It includes part of the townsite of the town of Timmins, and adjoins the west boundaries of the Hollin_ger Consolidated and Mace properties. The Moneta property was first staked in 1909, about a year after the first discovery of gold in the Porcupine camp. In 1910 the Moneta Company was incorporated and some preliminary exploratory work performed by Nova Scotia Mines of Cobalt. In 1912 English interests advanced $90,000 for diamond drilling and underground work. One drill hole gave high assays, but apparently the records were poorly kept or the cores were interchanged. As a consequence, when underground exploration was undertaken in 1923 it was directed south rather than west and no ore was found . In 1924 about 5,000 feet of diamond drilling was done in the southern part of the property, but without intersecting ore.In 1931 W. E. Segsworth assumed the direction of the property. Diamond drilling commenced on August 18, 1936. The first hole intersected 9.9 feet of ore averaging 1.23 oz. gold a ton. Underground work was started early in 1937. A mill was erected in the autumn and the first gold brick was poured January 29, 1938.The Moneta mill began operation on January 2, 1938, and the following table gives a summary of the production to June 30, 1943, when the mill was closed."

Jan 1, 1954

By Y. Hou, E. Arinaitwe, L. Tong

A series of dense medium separation (DMS) tests were performed on four low-grade copper ores from Mount Polley mine in order to determine their amenability to pre-concentration. The tested ores contained disseminated sulphides, mostly chalcopyrite with low copper grades (0.15% - 0.2%) and relatively high iron grades (4.76% - 5.63%). The samples were screened into different size fractions ranging from 9.5 mm to 50.8 mm and DMS tests were performed on each size fraction at various separation densities. The pre-concentration efficiency at different size fractions and separation densities was evaluated in terms of metal upgrading and distribution. Mineralogical tests were also performed on selected DMS sink and float samples in order to understand the influence of mineralogy on the pre-concentration efficiency. The results showed that significant copper upgrading was achieved for intermediate size fractions only at the highest separation density tested. The copper recoveries generally increased with particle size at all separation densities. However, it was impossible to upgrade the copper content in the ores and achieve acceptable recoveries and mass rejections at the same time. Copper recoveries and grades showed a strong correlation with iron recoveries and grades indicating that it is possible to pre-concentrate copper by recovering magnetite and other iron-containing minerals in the ore. Overall, the results suggest that the optimum separation density and pre-concentration efficiency is a function of particle size, and that the ore mineralization properties limit the performance of DMS as a pre-concentration technology for such low-grade disseminated ores.

Jan 1, 2014

Applications of proven real time, through-conveyor elemental analysis technology and benefits achieved will be discussed using case studies in base metals, iron ore and phosphate operations. PGNAA (Prompt Gamma Neutron Activation Analysis) technology and its background in minerals applications and applications which are expected to further improve its utilization will be reviewed. Short payback through operational benefits such as removal of waste from feed, increased feed grade and overall improved productivity will be demonstrated based on results achieved at several processing operations. PGNAA technology is most applicable to conveyed flows as it is unaffected by belt speed, particle size, segregation/layering, mineralogy or dust. As a transmission method able to penetrate in excess of 500mm of rock it provides extremely representative results continuously measuring through the full conveyed cross section and reporting results typically on one to five minute accumulated increments to the control room. Multi-elemental results and moisture content are used for active process control: diverting conveyed flow increments(bulk sorting), blending ore types in plant feed, and providing advance warning of significant quality changes to the downstream plant operators (e.g. flotation). Elements of interest may include deleterious components as well as target metals. Ore feed quality measurements are also useful in metal accounting, ore reconciliation and real time feedback to mining operations. Further benefits can result when combined with other technologies such as particle sorters, to upgrade diverted increments of subeconomic material to achieve higher feed grades and lower deleterious content to the main process. Measurement of elements (e.g. silica) which correlate with ore hardness or grinding characteristics can be used to moderate feed rate to grinding mills to prevent overload, hence optimizing grinding performance and reducing energy and grinding media consumption. Pebble flows can be analysed and uneconomic increments diverted to prevent recirculating flows consuming mill capacity unnecessarily. This also increases average feed grade.

Jan 1, 2016

By R. S. Douglas

Introduction The mine at Copper Mountain of the Granby Consolidated Mining, Smelting and Power Company was one of the pioneers in the use of blast-hole diamond drilling for ore breakage. This method of mining has now been brought to a high degree of perfection. The system in use has?been described in a previously published paper which has become an important part of the literature o the blast-hole drilling method. At the time of the establishment of the system at Copper Mountain, standardized loading and drilling procedures were set up. These procedures were based partly on the results of experiment and partly upon the judgment of men experienced in breaking rock in the mine. The success of the method has been proof of their adequacy. With the progress of scoping in the mine, the diamond drill method of breaking was applied to other ore blocks where different conditions obtained. It was found necessary to make adjustments in the standard procedures to get the best results under the new conditions. The following paper attempts to express, in terms of mathematics, the relations of the variable factors. Until recently, estimations of drilling required were based upon the tonnage to be broken and the proposed rate of explosive loading. A revised method of estimating is outlined below which is direct and which involves no unrelated variable factors.

Jan 1, 1947

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007

By Robert T. McKnight

"Traditional techniques for valuing resource projects companies have been primarily based on discounted cashflow methods (DCF) or by comparison to similar projects with an apparent market capitalization. Many resource projects are really forms of options to invest rather than a future cashflow stream. Employing the DCF method to value a resource project which is really an option to invest, can dramatically underestimate the real value of the project. The analytical tools required to evaluate options, while more complicated than the usual spreadsheets used for DCF, are becoming more easily available and usable by managers. This paper will discuss the background of options valuation and some of the tools which will make it easier for managers to estimate the value of projects and companies which have significant real option values.ResumeBob McKnight is a graduate of the University of British Columbia in Geological Engineering, supplemented by an MBA from Simon Fraser University. Following several years in the oil patch with Cities Service and Brascan, Bob returned to Vancouver in 1979 to work for Wright Engineers. He subsequently went on to work for Cassiar Mining, Getty Resources and Endeavour Financial before joining Pincock Allen & Holt Ltd. in 1998. His experience ranges from exploration to feasibility studies, financial evaluations of mining and oil & gas projects, due diligence, project finance, valuations and mergers and acquisitions. He has extensive international mining experience pertaining to such countries as Chile, Mexico, Uruguay, Thailand, Indonesia, Angola, Papua New Guinea, Kazakhstan.What are Options?Options have been around for centuries. They were familiar to Roman and Phoenician traders who were shipping cargoes from Mediterranean seaports. In the financial world, options are types of contracts that generally include the right, but not the obligation, to buy or sell a share, currency or commodity. The underlying commodity price or share price changes are assumed to be lognormally distributed. In this context, options are of two general types, ""call"" options and ""put"" options. Call options have the characteristic of having the right to buy a tradable commodity or currency at a predetermined price for a specified period of time. For the owner of call options, they become more valuable as the price of the underlying commodity increases. For the seller of call options, these options become an increasing liability as commodity prices rise, since there is the obligation to sell the commodity at a predetermined (perhaps lower-than-market) price. This characteristic of call options recently became high profile with the sharp rise in gold prices last year. The value of gold call options sold by certain producers increased their associated liabilities to the point where margin calls were made."

Jan 1, 2003

By Vic Casaletto

"IntroductionThe Canadian mining industry is under immense pressure to compete with foreign mine operations. The very survival of the Canadian mining industry is threatened by lower ore grades, environmental pressures, high cost of labour, unfriendly tax laws toward exploration and the increasing cost of new technology. In order to compete in the world market, Canadian producers and their suppliers are rethinking age old customer-supplier relationships in favour of preferred supplier relationships which can improve the profitability and enhance the competitive position of both partners.This paper attempts to redefine partnerships with suppliers in the context of a ""win-win"" objective. It will outline the measurable benefits to both partners through a representative product which highlights the keynote structure of any successful supplier partnership The Status Quo...Mines all over North America are plagued with the same recurring questions, ""Who has the best product for my operation at the lowest price... How do we know a product will perform to a supplier's projections after the sale...What do we do if the product fails to perform as expected?"" These questions have been asked by underground mining operators for decades but rarely have long-term solutions with measurable results been achieved.The LHD industry is one example of the status quo where partnerships will provide large gains toward technological advancement, reducing mobile equipment costs. The underground mining industry is out of sync with their surface counterparts in the open pit business.Partnerships with suppliers in the open pit world are not only a standard practice but a culture which has existed for decades. Open pit operators enjoy concepts which fix their mobile equipment costs for the life of the mine and hold the equipment supplier accountable for performance and fleet economics for 60 000 service hours and longer.Manufacturers are attempting to transfer this culture into the underground mining industry. Figure I illustrates the significance of a capital driven decision."

Jan 1, 1994