Search Documents

By Ryan T. Smith, Anthony Sahj, Alexander T. Darnell

Every second can count when trying to board a departing flight or catch a ride-share to your final destination. Hartsfield-Jackson Atlanta International Airport is in the midst of a project that aims to cut about 13 seconds between automated people mover trains (Plane Train) that move passengers between the terminals and concourses. The project involves extending the Plane Train tunnel west from its existing terminus under the domestic terminal. Working from inside non-public areas of the terminal, Keller North America, Inc. (Keller) incorporated systems of micropile-supported steel beams and grillage to both underpin existing columns prior to tunneling and support open-cut excavation at the tie-in of the new to the existing tunnel. Dewatering aided in mining a challenging section at the start of the drive of the mixedface, sequentially excavated tunnel and an automated instrumentation system monitored the performance of the construction and its impact to the terminal. Cut and cover egress and ventilation tunnels required braced support of excavation.

Oct 1, 2022

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017

By Kevin R. Johnson, Matt Caskey, Bryan Plaskett

Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical design and construction. These challenges can include constrained sites with limited access and laydown area, vibration concerns for adjacent structures, and the need to complete work within limited schedules. When challenging geotechnical conditions like variable bedrock elevations are present, the need to balance performance requirements with logistical constraints become the driving factor when selecting deep foundation systems. This paper focuses on the deep foundations used for a new elevated pedestrian bridge at a major health care facility in Tampa, Florida. In addition to the technical design requirements, the owner required a deep foundation system that could offer low vibrations, rapid production, and clean installation to limit impacts on their properties and the public roadway that separated them. The paper describes the project specific geotechnical and design conditions, describes Ductile Iron Pile design, and focuses on how installation of the system addressed the unique logistical challenges. In addition, the implementation of a full-scale load testing program to assess compression, uplift, and lateral design capacities is presented. This paper represents one of the few published references for Ductile Iron Piles on projects in the United States.

Oct 1, 2022

By Arash Khosravifar, Ali N. Ibrahim

"Large areas of Iraq are covered with collapsible soils namely gypsiferous soil which is often used as the foundation soil for structures. In particular, the Mosul Dam foundation is comprised of high contents of gypsiferous soils. Intrusion of water through the foundation soil dissolves gypsum which acts as the binding material between soil particles. This phenomenon results in the formation of collapsible soils which can cause serious damages to the dam structure. The failure of Mosul Dam, with a reservoir as large as 11 billion cubic meter of water, can be catastrophic. In the past, Mosul Dam Authorities have been remediating the soil foundation by injecting cement mortar. This method has been proved not economic; therefore, new, more efficient, methods are desperately needed.This research study focuses on finding practical methods to remediate collapsibility of gypsiferous soils by improving their geotechnical properties. This study presents remediation of collapsible gypsum-rich soil by grouting. Three types of stabilizer materials were used to make the grout; (1) sodium silicate (Na2 O3 Si) which is a well-known chemical soil stabilizer, (2) bentonite slurry, and (3) silicone oil. The purpose for using these stabilizer materials is to provide an impermeable layer (waterproofing coat) around the gypsiferous soil particles and to fill the voids that may occur in the soil as a result of gypsum dissolution when subjected to water.A series of double oedometer (collapse) tests and direct shear tests were carried out on gypsiferous soils before and after remediation by grouting. The results show that the soil compressibility decreases in the grout-treated gypsiferous soil by reducing volumetric strain. Consequently, the potential for collapsibility decreases too. It was also shown that grouting, increases the shear strength of the soil at confining stresses smaller than 250 kPa by increasing the cohesion combined with a slight reduction in the internal friction angle.INTRODUCTIONGrouting is one of the ground improvement techniques which is often used to improve the loose foundation soils. Bruce (2003) provides step-by-step procedures on using grouting techniques for sealing dams and other water reservoirs. Grouting can be classified as permeation grouting, compaction grouting or hydraulic fracturing. Permeation grouting is an effective way to send the grout into the ground without disturbing the soil structure, i.e. free flow of grout into the soil voids where grouting is accomplished by injection of a fluid-like material that is capable of forming a gel and binding the soil particles together. Grout materials may be solution grouts or suspension grouts. The permeation grouting technique is generally used to minimize ground permeability and to control ground water flow, but it can also be used to strengthen and harden the ground (Raman et al., 2012)."

Jan 1, 2017

By Gene Bryant, Wesley Schmutzler, Matteo Bertoni

The levees where the Mississippi River and the Lower Wood River meet near East Alton Illinois have been a problem area for years due to underseepage. The first phase of the deep cutoff wall was a 2,000-linear foot section that was completed in 2016 for the Illinois Flood Prevention District Council. This section was installed along the Wood River and the Mississippi river to depths of over 135’, The United States Army Corps of Engineers was tasked with continuing the cutoff wall along the Mississippi river. The wall was a continuation of phase I with depths up to 140’. The 1,000’ long cutoff wall was installed through fill, loose sands, cobbles, and sandy clay. The cutoff wall was terminated in either Glacial Till or sound rock. In order to provide wall permeability equal to or less than 1.0 X 10-6 cm/sec a self-hardening slurry (SHS) composed of ordinary Portland cement, slag cement, and water was utilized. The depths reached on this project using SHS is the deepest done to date in the United States. Along with the permeability requirements, a very narrow range for the unconfined compressive strength was specified at 50 – 180 PSI. In order to monitor the ground movement and water level fluctuations during the excavation of the panels with the Hydromill or Clamshell, 6 automated inclinometers were installed and monitored continuously during panel excavation in phase 1. Seven automated piezometers were monitored in phase 2. This paper will give an overview of the project with emphasis on the effect of the excavation on the instrumentation, specifically the reaction of the piezometers as the last panels were installed. INTRODUCTION The project is in Illinois, about 1000 feet downstream from where the Wood River Creek enters the Mississippi River between East Alton, IL and Wood River, IL adjacent to State Highway 143 (Fig. 1). The Wood River Lower Cutoff Wall Phase 2 Project (WR2) was awarded to TREVIICOS SOUTH (TIS) in September 2017. The Main Project features are: Construction of work platform, inclinometers installation and removal, cutoff wall construction by the Self-Hardening Slurry method (approx. 135,000 sf) up to 140' depth, clay cap installation, and site restoration. The levee system along this stretch of the Mississippi River has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed to ensure that Levee failure would not be an issue in the future.

Jan 1, 2019

By H. R. Masoumi

This paper presents a numerical model for the prediction of free field vibrations due to vibratory and impact driving. As the focus is on the response in the far field, where deformations are relatively small, a linear elastic constitutive behavior is assumed for the soil. The free field vibrations are calculated by means of a coupled FE-BE model using a subdomain formulation, proposed by Aubry and Clouteau (1992). The model is validated by means of the results of Kaynia and Kausel (1991) for the impedance of a single pile. First, the case of vibratory pile driving is considered, where the contributions of different types of waves are investigated for several penetration depths. The results show that in the near field, the response of the soil is dominated by a vertically polarized shear wave, whereas in the far field, Rayleigh waves dominate the ground vibration and body waves have been importantly attenuated. Second, the case of impact pile driving is considered. A linear wave equation model is used to estimate the impact force during the driving process. Furthermore, it is investigated how the soil stratification influences the ground vibration considering the case of a soft layer on a stiffer half space. The results show that when the penetration depth is smaller than the layer thickness, the layered medium has a small influence. However, when the penetration depth is larger than the layer thickness, these effects become more significant. Finally, the computed ground vibrations are compared with experimental data reported in the literature.

Jan 1, 2006

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By Shyam Chengalath, Johan Jeansson, Magnus Hörman

Down-The-Hole (DTH) drilling usually uses compressed air to power the hammer. However, there are now DTH hammers on the market which instead of compressed air use high pressure water to power the hammer. There are several benefits with using water DTH compared to air DTH, which are discussed in more detail in this paper. From a physics point of view many of the benefits arise from the fact that water is an incompressible media and air is not. Energy consumption is roughly a quarter compared to air, resulting in lower carbon emission and a lower energy bill. In the case of water DTH the water leaving the drill bit in the hole is at a low velocity and ambient pressure. However, with air DTH the air leaving the drill bit in the hole is at a high velocity and high pressure. This means that the risk of damaging surrounding structures in sensitive areas such as urban environments and dams, is greatly reduced with water DTH. In this paper two cases where water DTH is used in jet-grouting applications are discussed in detail. As these cases show there is a clear improvement in productivity when using water DTH hammers.

Sep 1, 2022

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By Joseph A. Sopko

There has been a trend in recent years in performing the initial formation freezing using liquid nitrogen (LIN) and then converting the system to circulating refrigerated brine. While proponents of this method state it decreases freezing time, it can also be considered an alternative to inadequate refrigeration capacity. This method was used on several small projects in the 1980s. Problems such as broken pipes, frozen brine, and unsafe work conditions caused contractors to re-think the method. This paper discusses these problems and also presents work schedules showing no schedule reduction. In fact, this method can lead to longer time as well as significantly higher costs. BACKGROUND Ground freezing as a method to provide groundwater control and temporary earth support for excavations is completed using a relatively simple process: drilling and installing refrigeration pipes around the perimeter of the excavation and introducing a coolant into these pipes. The coolant extracts heat from the ground, converting the pore water to ice and forming a strong, impermeable material. A typical ground freezing system is illustrated in Fig. 1. SYSTEMS There are two basic types of coolant systems: circulating and direct expansion. The circulating coolant system is made of two separate, closed systems. The medium circulating is the secondary coolant. It is cooled at a central refrigeration plant, circulated through the pipes, and warms as it extracts heat from the ground. It then circulates back to the plant where it is cooled. This coolant is chilled in a heat exchanger by the primary refrigeration system where a compressor system is charged with a refrigeration gas. The heat is ultimately extracted from the ground and expelled into the atmosphere by an evaporative condenser. Secondary coolants are usually a brine or glycol chemical while the primary refrigeration gas is anhydrous ammonia or another commercially available gas.

Jan 1, 2019

By Daniel A. Thome, Robert C. Janke

"Installation of permanent soil nails through distressed mechanically stabilized earth retaining walls is a cost effective and aesthetically pleasing solution when using the appropriate equipment and drilling methods for installation. A forensic investigation was performed on an existing mechanically stabilized earth retaining wall to determine the possible causes for the excessive horizontal displacements and visual structural flaws found along a portion of the wall. Reports concluded that the visual shifting was due to a number of factors including improper drainage in the vicinity of the wall and unsuitable compaction of the backfill material. Conceptual designs were proposed to the owner and the installation of permanent soil nails through the existing precast panels was determined to be the most practical solution. A total of ninety-three permanent soil nails were installed to lengths of up to 40 feet (12 m) through sand backfill and silty day fill using a hydraulic rotary percussion drill attached to a tract mounted excavator.IntroductionThe Illinois State Toll Highway Authority awarded Contract RR-03-5144 in the summer of 2004. Construction work for the project consisted of the rehabilitation of two existing concrete culverts and approximately 100 linear feet (31 m) of mechanically stabilized earth (MSE) retaining wall. The retaining wall is located below the southbound lanes of the Tri-State Tollway near the intersection of Federal Highway 41 in Wadsworth, Illinois as shown in Figure 1.Reports were prepared by Applied Technologies in cooperation with Giles Engineering Associates to determine the condition of the MSE wall and recommended conceptual designs to extend the service life of the wall.Nicholson Construction Company (Nicholson) wasselected as the design-build geotechnical subcontractor to install the recommended permanent soil nails through the existing precast concrete panels of the MSE wall. Rehabilitation of the wall involved the installation of ninety-three permanent soil nails through the existing wall, along with soil nail verification tests and proof tests on production nails."

Jan 1, 2005

By Martin Mcdermott, Kevin Tehansky, Robert Ross, Jeffrey Goodwin

A foundation value engineering redesign is a collaboration between the project owner, original design team, general contractor, foundation contractor and redesign team. Without the acceptance and collaborative effort of all the stakeholders, the redesign process is doomed to failure. For the addition at the Hackensack (New Jersey) University Medical Center (HUMC) we had just such a collaborative effort for the drilled shaft redesign. For a successful redesign effort, the collaboration between the foundation contractor and their redesign team needs to fully exploit the contractor’s specific equipment and experience and convey how to apply this to the project as a whole to ensure everyone is confident that the project design goals are being met. For the HUMC project, applied load testing of the drilled shafts (bi-directional and lateral) were used to provide ultimate geotechnical design values for the redesign effort. By utilizing the contractor’s preferred equipment and the redesign team’s testing and application expertise, the redesign collaboration was able to enhance a good design and make it into a great project.

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The stadium development consists of construction of a 68,500-seat, open-air NFL football stadium for the San Francisco 49ers. The main structure will consist of a 7-story above grade steel structure supported by over 3,000 piles. Berkel and Company Contractors, Inc. (Berkel) was selected as the design-build pile contractor who used their auger pressure grouted displacement (APGD) piles for this project. During an indicator pile installation and pile load test program, fifteen piles were tested to develop installation criteria to support demands of 150kips tension and 180 kips compression. Following the indicator pile program Berkel installed 3088 piles in 30 working days. Throughout pile installation data were collected with an automated data acquisition system (DAS). During pile installation field engineers from Treadwell & Rollo observed the pile installation as well as the real-time data from the DAS. Strategic staging and pre-production planning by Berkel along with consistent collaboration with the design team created an atmosphere for a successful and on schedule project completion.IntroductionThe new San Francisco 49ers Stadium in Santa Clara, California will be a 68,500-seat facility, a rendering of which is shown in Figure 1. The main structure will consist of a 7-story above grade steel structure supported by more than 3,000 piles. The north, east and south portions of the stadium are designed as an open seating bowl, while the western portion includes open seating at the lower levels and seven-story tower which houses over 150 suites.The stadium project includes the stadium structure, as well as elevated open pedestrian walkways, commercial community space, and three new pedestrian bridges spanning a nearby by creek. Sustainable designs and innovations such as a green roof, photovoltaic panels, a ground source geothermal system, stadium-wide Wi-Fi capability, and access to public transit are provided throughout the project. The stadium is designed as an open, light, and airy structure and is surrounded by an existing amusement park, office buildings, the Santa Clara Convention Center, and the training facility of the 49ers."

Jan 1, 2015

By Jianhua Wang, Jianming Yao, Zhen Meng, Jinjian Chen

"Drilled screw pile is a newly developed displacement pile foundation which has been applied in soft clay for many years. Compared with traditional circular displacement pile, It is characterized by high bearing capacity, small volume and small squeezing effects. For the purpose of investigating the squeezing effects of drilled screw pile, a full scale field monitoring test with two test piles was performed. Detailed soil horizontal displacement and pore pressure measurements were conducted in the vicinity of the two drilled screw piles during penetration and subsequent soil consolidation. It can be concluded that the horizontal displacement of the surrounding soil induced by the installation of a drilled screw pile is mainly in a circular region with a diameter of 3 m (r/D<6), and the compaction effect outside the area can be essentially negligible; The excess pore pressures measured at the same time increase with depth throughout the entire process of consolidation, and its dissipation shows an exponential decay as a function of time.INTRODUCTIONA knowledge of the displacement and stress changes induced in the soil surrounding a pile is very important for evaluating pile performance. Numerous field and laboratory research projects have examined loading conditions, total soil stresses, and excess pore pressures during and following pile installation (Pestana et al., 2002). A relatively comprehensive and detailed review of these experimental works from 1948 to 2002 was presented by Pestana et al. (2002). More recently, Xu et al. (2006) conducted a field experiment to study displacements and stresses in the vicinity of two pipe piles during their installation in a soft lightly overconsolidated clay and compared the field measurements with existing predictive methods. Abdrabbo and Gaaver (2011) collected field observation data from four different construction sites to study soil disturbance during construction of piles using continuous flight auger (CFA). They have found that the disturbed zone of soil by CFA has a conical shape and the excess pore pressure has no appreciable influence on the load capacity of the piles.Drilled screw pile (DS pile) is a kind of vibration-free, cast-in-place concrete pile. Because of the excellent bearing performance, low level of vibration pollution and negligible spoil, as well as its fast construction speed, DS pile has been widely accepted by many engineers around the world. As a new type of drilled displacement pile, the significant installation effects of DS pile on the adjacent soil have not been systematically and integrally investigated yet. Since a proper numerical simulation of the real installation process of DS pile is difficult to achieve, the investigation based on field measurements is necessary. This paper presents a field investigation of the installation effects of two DS piles on surrounding soils. Detailed horizontal soil displacement and pore pressure measurements during pile installation and subsequent soil consolidation have been conducted. Based on the monitoring data, variation of horizontal displacements and dissipation of excess pore pressures with depth and time have been analyzed. What's more, the construction machinery and technology used in DS pile installation are also simply introduced."

Jan 1, 2015

By Aaron Evans, Chu E. Ho, Tom Richards

"This paper describes an innovative case history of using jet grouting to form a groundwater cutoff wall at the interface of a cut-and-cover construction and an existing tunnel. The design of the jet grouting layout was complicated by the presence of a left-in-place bulkhead of unknown dimensions abandoned by previous construction of the existing tunnel. Jet grouting was performed through predrilled holes within the narrow space between the existing bulkhead sheeting and tunnel structure. A systematic sequence of primary and secondary jet grout elements of varying diameters and panel lengths was executed to achieve an effective groundwater barrier. A key challenge in the jet grout design was the impact of potential deviations due to shadowing effects of the left-in-place bulkhead sheeting and pre-formed jet grout columns, as well as overbreak concrete in adjacent secant pile walls. The flexibility of the jet grouting methodology enabled a wide range of operational parameter combinations to be performed, allowing column diameters to be adjusted based on actual field installation measurements. Special precaution was exercised when grouting at critical locations to avoid over-pressurization and damage to the existing tunnel structure.IntroductionThe 96th Street Station box for the new Second Avenue Subway Line in Manhattan, New York included a transition tunnel, which connected the station to an existing tunnel built in the early 1970s (Figure 1). The new station and transition tunnel were both constructed using the cut-and-cover technique with bottom-up sequence (Aksman et al. 2012, Grigson et al. 2016). The main station structure incorporated permanent diaphragm walls for most of its length, except for the southern segment where high rock levels were encountered and the station box was constructed within temporary secant pile walls socketed into the rock. The permanent diaphragm walls were also utilized for temporary excavation support (Ho and Hu 2014). At the northern end of the site, the new transition tunnel was constructed within temporary secant pile walls that extended from the station diaphragm walls to the existing tunnel at the tie-in location. A temporary traffic deck spanning 60ft across the secant pile and diaphragm walls along the full excavated length of the site allowed traffic to continue operating at street level while construction of the station and transition tunnel progressed below grade."

Jan 1, 2016

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"Previous studies revealed that the helix deflection reduced the end bearing capacity of screw pile in dense ground even if the installation process is completed with minimal soil disturbance. The ultimate end bearing capacity in dense ground is difficult to achieve during the full-scale pile load test due to the limitation of the loading system. Therefore, in the present study, model scale of testing is selected to investigate the effect of helix deflection on load settlement behavior of single helix screw pile under increasing stress level. It is observed from the test results that the applied surcharge pressure, which is used to simulate the effect of stress level, is decreased with increase in model ground thickness. This decrease in the stress level is due to the frictional resistance between the container wall and sand. It is also observed that the end bearing capacity of screw pile increases with the increase in stress level but at gradually decreasing rate. The test results indicated that the helix deflection during the pile load test should not be more than critical deflection (0.72 mm average) of the helix to avoid any reduction in the end bearing capacity of screw pile. The helix deflection, which is measured after the pile load tests are also compared with the equations of flat circular plate having uniformly distributed load over the plate with simply supported and fixed inner edges.INTRODUCTIONThe screw pile consists of a central steel shaft with one or more helices attached at different location on the central shaft. The installation mechanism of screw pile consists of torque and pushing force. The screw pile installation mechanism can affect the unit weight of the ground during its installation. This effect is small in cohesive soils but it is quite noticeable in loose to medium dense sands (Adams 2011; Santos et al. 2013). The pushing force should be controlled in such a manner that pile penetration should be at least 80% of the pitch of the helix, during each revolution (Perko, 2009)."

Jan 1, 2017

By Serge Borel

An efficient design method is proposed for "piled-footing" and "piled-raft" foundation under lateral loads. It combines the methods used for the displacement design of shallow and deep foundations and takes into account the interactions between the piles and the cap or raft. This method has been applied to previous full-scale tests carried out in the United States. Two groups of six instrumented driven piles were laterally loaded several times: first with the concrete pile cap in direct contact with the soil, and then, after a thin layer of soil had been removed beneath the cap. The proposed method models well the real behavior of piled-raft foundations. It highlights the positive effect of the cap in contact with the soil, which reduces significantly the displacements and the maximum pile bending moments. These are divided by two for the analyzed case histories.

Jan 1, 2002

By Craig M. Shillaber, Joseph E. Dove, James K. Mitchell

"This paper addresses two primary factors affecting the sustainability of Deep Mixing Methods (DMMs): construction materials and handling of the spoil from wet mixing methods. We examine these factors within a life-cycle embodied energy (EE) and carbon dioxide (CO2) emissions accounting framework, using the LPV 111 project in New Orleans, LA as a case history. The underlying assumption is that project planning and preliminary design have determined that a DMM is the best ground improvement alternative for achieving the broader aims of sustainable development. While EE and CO2 emissions are direct measurements of environmental impact alone, we illustrate how their minimization can also influence the social and economic consequences of the project. It is recommended that DMMs use lower energy and carbon material alternatives to Portland cement and lime in the binder whenever possible, with preference given to locally sourced materials. Currently available alternative cementitious materials include fly ash and slag, which are waste products from other processes. In addition, recycling the spoil material from wet mix methods on site is recommended. If the material cannot be recycled on site, transporting it to a processing and recycling center for later use as fill is preferred over landfilling. INTRODUCTIONWithin the geotechnical community there is an increased appreciation for sustainability considerations, which are an important component of the planning, design, construction, operation and maintenance of projects. An assessment of project sustainability includes holistic life cycle thinking, systems analysis, environmental impact assessment, use of safe and benign materials, awareness of local societies and cultures, social equity, protecting human health and well-being, and monetary costs (Abraham, 2006). Since ground improvement is a principal practice domain of geotechnical engineers, it is important that geo-professionals play a role in addressing the sustainability for these projects. In this paper, we illustrate by case history how different materials and methods associated with deep mixing projects can impact overall project sustainability through quantifying project embodied energy (EE) and carbon dioxide (CO2) emissions. EE is defined as all energy consumed to bring something into its present state (Chau et al., 2008; Inui et al., 2011; Soga et al., 2011; Chau et al., 2012). Recommendations are then made for how adverse environmental impacts of Deep Mixing Methods (DMMs) may be minimized, leading to more sustainable geotechnical construction."

Jan 1, 2015

By Takeshi Maki, Kh. Adeel Tariq

"The lateral resistance of the structure plays an important role during seismic event and it can be increased by using ground improvement. In this study an attempt has been made to investigate the effect of cement-treated sand on the lateral capacity of the pile. The behavior of piles surrounded by sand only and cement-treated sand confined in a steel box (30 x 30 x 50 cm) which is subjected to lateral cyclic load has been investigated. Piles having a diameter of 2.5 cm and embedded to a depth of 45 cm were used. Steel and aluminum piles were used to investigate the effect of flexural stiffness on the lateral capacity of the pile. Bottom supports of piles were also changed from pinned to fix. Well graded sand compacted to 70% of relative density (RD) was used. Cement-treated sand having a compressive strength of 3.7 MPa was used. Displacement controled lateral load tests were performed and cyclic loads were applied until pile displacement was 4%, 10%, 20%, 35%, 50%, 75% and 100% of pile diameter. Results evaluated are compared with common method of analysis like Brinch hansen (1961), Brom (1964), Poluos (1980) etc. Results have indicated that the stiffness of a pile affects its lateral capacity. The introduction of central cement-treated sand part increased 5 times the lateral capacity of piles as compared with a sand only condition.IntroductionPiles are used extensively around the world to support loads of structures. Piles are commonly used to carry axial load, but in some structures, the lateral capacity of the pile is more important than the axial capacity: for example piles supporting earth retaining structures, electric tower foundation, etc. Structures can be subjected to both axial and lateral forces, like structures constructed at harbor that are subjected to lateral force due to waves action; and structures built in earthquake prone areas like Japan."

Jan 1, 2017