Search Documents

By Robert P. Vinson

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SF6) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By E. R. Palowitch

A centrifugal float-and-sink test procedure has been developed by the Bureau of Mines to reduce the time for the gravimetric separation of coals finer than l4-mesh from as long as 24 hours to less than 1 hour. Comparative tests indicated that centrifuging a minus 14-mesh Pittsburgh-bed coal for 20 minutes at 1,500 revolutions per minute produced results that compared favorably with static float-and-sink test results. Standard deviations of the mean recovery and ash content of the float obtained centrifugally ranged from 1.31 and 0.04 percent, respectively, at 1.30 specific gravity to 0.21 and 0.05 percent, respectively, at 1.60 specific gravity. As in static separations, retreatment of the products separated at low specific gravities was required.

Jan 1, 1961

By E. V. Cilento, K. A. DiGregorlo, R. C. Lantz

A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared to experimental results obtained from single rat PAM. The O2 - was quantified by measuring the reduction of nitroblue tetrazolium (NBT) to a diformazan precipitate (NBTH2) from video-recorded images of individual cells. The kinetic model considered three reactions: (1) the production of extracellular 0 - from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, (2) the subsequent dismutation of o2- to from O2 , and (3) the reaction of o2- and NBT. NBT specificity for o2- was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) which catalyzes the dismutation of o2- to H2o2. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations since NBT is a relatively small molecule (818 MW) compared to SOD (34000 MW). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/or electrostatic effects since SOD is also negatively charged.

Jan 1, 1988

By T. Kessler

Spark-source mass spectrometry has been used to determine the amounts of minor and trace elements in coal particles of various sizes, including the respirable range (<5 microns). Fifty-six elements ranging in concentration from 0.1 ppm wt to 5,000 ppm wt have been determined. The investigation of coal and coal ash has shown that the organic material in coal does not interfere with the spark-source determination of the various elements.

Jan 1, 1971

By V. A. Marple, K. L. Rubow

"4.1 IntroductionIn previous chapters impactors have been described as useful instruments for classifying particles by their aerodynamic diameters and for measuring particle size distributions. These impactors can be used most reliably if the user has some understanding as to how the impactor classifies particles and what parameters are important in this classification process. This understanding can best be obtained by a theoretical inspection of inertial principles.This chapter reviews the most recent theoretical impactor work and the latest theoretical efficiency curves. Procedures are then given for using these efficiency curves in the design and evaluation of cascade impactors. Finally, several examples are given comparing theoretical and experimental efficiency curves, pointing out when the theory can be used with great confidence and when the theory should be used only as a guideline.Due to the rather simple principle of operation of an inertial impactor (i.e., the impingement of a jet of particle-laden air on a flat plate) the impactor readily lends itself to theoretical analysis. Three notable works in the early 1950,s were those of Davies and Aylward (1951), Davies et al. (1951), and Ranz and Wong (1952).Davies and Aylward (1951) used a method of conformal mapping to obtain an analytical solution to Euler's equation for the flow of a frictionless fluid through a rectangular impactor. Numerical calculations were then carried out whereby the equations of motion of the particles were solved in a stepwise manner, leading to a determination of the efficiency curves. Since this theory assumed potential flow, the effect of Reynolds numbers on the characteristics of the impactor could not be determined.Ranz and Wong (1952) used an approximate flow field to calculate the efficiency of both round and rectangular nozzle impactors. In the vicinity of the stagnation point, the flow field was assumed to be that of frictionless stagnation flow. Here, the resulting equation of motion for the particles was found to be in a form similar to equations for free vibration with viscous damping. Therefore, the known solutions of the vibration equations were applied directly to the problem and the efficiency curves calculated. This solution technique, however, could not take into account the various geometric variations such as the jet-to-plate distance in the determination of the efficiency curves.The work of Ranz and Wong (1952) was later modified by Mercer and Chow (1968) and Mercer and Stafford (1969) so that the rather simple flow fields of Ranz and Wong (1952) could be used to account for various jet-to-plate distances. The same techniques, however, were used to determine the impactor collection efficiency curves."

Jan 1, 1986

By F. J. Smith, W. A. Gallagher, C. A. Herbert

"INTRODUCTION A fire started about 10 a.m., November 10, 1947, at the Kings mine, Princeton Mining Co., Princeton, Ind., about 1,800 feet inby the main shaft bottom on the main west haulage road at a point estimated to be 2 miles from the faces of the main west entries. No lives were lost, as 27 men escaped from the mine after a series of explosions, which necessitated sealing the mine on the surface. This information circular shows"" how adverse conditions might be overcome, when reopening a sealed mine, by expert planning and close cooperation on the part of various organizations. Conditions found in the mine after it was reopened were comparable to the worst that had been anticipated, yet the mine was recovered with comparatively little difficulty and a minimum of risk. The open workings in the mine covered a vast area, but most of the mine resumed production of coal after being sealed for only 37 days.The information contained herein also points to the desirability of adhering as closely as possible to a predetermined schedule of operations."

Feb 1, 1949

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (-300° C) and later (>400° C) combustion stages of mine conveyor belts could be predicted by a smoke particle characteristic. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 150°, 250°, and 1,000° C, with a furnace airflow of 10 L/min. The variables studied, as a function of time, included hydrogen chloride and carbon monoxide concentrations, the average smoke particle diameter (d8 and number concentration (no), and the product of the average smoke particle diameter and concentration (dgn0) Other variables included the sample and furnace temperatures and the sample mass weight loss. Results show that the inverse of the smoke particle diameter-concentration product (ldgn0), correlates directly with the hydrogen chloride and carbon monoxide toxicities released in large quantities during the early and later stages of combustion.

Jan 1, 1989

By Joseph Grumer

The range of composition of gases synthesized from solid fuels which are exchangeable with natural gas on current gas appliances was evaluated by theoretical principles. These principles consider primarily the flashback, blowoff, and yellow-tipping characteristics of air-entraining burner flames. It was found that complete identity between the synthetic and natural product is not necessary. Gases such as may be obtained by hydrogasification of coal and other solid fuels without the removal of unreacted hydrogen offer advantages in flame characteristics. Between 25 to 37 percent hydrogen can be tolerated in the sendout gas.

Jan 1, 1965

By L. C. Marchant

Results of detailed analyses of four cores from the Threemile Canyon area in the P. R. Spring tar sand deposit in Utah are reported by the Bureau of Mines. The cores were obtained by the Utah Geological and Mineralogical Sur-vey as part of a l7-corehole evaluation program in the P. R. Spring, Hill Creek, and Rim Rock tar sand deposits. Average properties of the oil zone in the Threemile Canyon area as deter-mined from these cores are as follows: Oil saturation, 67.4 pet of pore volume; porosity, 29.2 pct; permeability before oil extraction, 133 millidarcies; and permeability after oil extraction, 2,855 millidarcies. Average net thickness of the oil zone is 23.8 ft and average depth to the top of the oil zone is 189 ft.

Jan 1, 1974

By Robert M. Cox

The objective of this study was to determine if significant relationships exist between coal mine roof stability and the time roof is left unsupported. Additional factors such as geology, opening geometry, and mining methods were also studied: to determine their relative influence on mine roof stability. The results of the study indicate that geologic factors such as shear zones (either joints or faults) and changes in roof rock lithology were the principal factors governing mine roof stability. The time lapse factor appeared to be of critical importance when poor mine roof conditions are encountered. The study pointed up the need for improved and permissible rock mechanics instrumentation for use in coal mine investigations.

Jan 1, 1974

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man&apos;s first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930&apos;s the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious. In addition to agricultural and building lime the sales statistics compiled annually by the Bureau of Mines include lime sold to the steel and other metallurgical industries as refractory and fluxing material, as well as that used by paper mills, glass works, tanneries, and water-treatment plants. These major uses normally consume about 86 percent of the domestic sales. The remaining 14 percent includes lime sold for use in the manufacture of alcohol, alkalies, bleaches, calcium acetate, calcium carbide, coke gas and byproducts, glue, insecticides, oils and fats, paints, and rubber, in the refining of salt, in the manufacture of sand-lime and slag brick, in the disposal of sewage and garbage, in the manufacture of silica brick, in the refining of sugar, in the textile industries, and in wood distillation. Many other uses are also known for which complete sales data are not available.

Jan 1, 1934

By C. Özgen Karacan

The methane emission rate into an underground mine environment from overburden strata during longwall mining is impacted by reservoir and geomechanical characteristics of the coal measure rocks in the overlying strata, as well as the presence of any coal seam. The reservoir characteristics and how they change during mining potentially affect the performance of gob gas ventholes, which consequently impacts the efficiency of methane control in the mining environment. This study presents reservoir and elastic properties of coal measure rocks in the Lower Monongahela Group in Greene County, southwestern Pennsylvania, of the Northern Appalachian Basin. Since the source of methane in this region from underground mining is located between the Sewickley coal and the Pittsburgh coal, a specific emphasis was given to this interval. Core analyses were performed in the laboratory to determine rock porosity and permeability. Geophysical logging data (gamma, density, sonic) obtained from two exploration boreholes were used for evaluating formation boundaries, shale contents, log porosities, and geomechanical properties of formations. Permeability was also calculated using density-log data and empirical equations and compared with laboratory measurements and slug tests performed in isolated intervals of boreholes. The results presented in this study can be used as data sources for reservoir studies related to the production and control of methane.

Jan 1, 2009

By R. T. DeWoody, W. C. Miller, W. Chester

Studies were made to determine the effect of the shape of a pneumaticrock- drill exhaust muffler on its efficiency, and the origin and reduction of exit noise from the mufflers. Tests of mufflers of three different shapes proved that the shape is not critical and that a muffler could be incorporated into the shell of the drill. Petal diffusers are beneficial in reducing exit noise but add another projection to the machine. Increasing the number of exit openings while maintaining the same area of exit opening has a markedly beneficial effect on the exit noise and appears to be the most satisfactory treatment.

Jan 1, 1964

By J. A. Eisele

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has studied the removal of iron from simulated aluminum nitrate leach liquors by solvent extraction. Iron must be removed from aluminum nitrate liquor produced by leaching calcined kaolinitic clay with HN03 to reduce the iron level in alumina to less than 0.02 wt-pct Fe203 for use in reduction cells. The parameters reported are for (1) extracting iron from a feed containing 1.5 g/l Fe with di(2-ethylhexyl) phosphoric acid (EHPA), (2) stripping loaded organic phase with 20-pct HCI, and (3) water washing of loaded and stripped organic phase. Recommended operating conditions are two extraction stages using 15 vol-pct EHPA in kerosene and three stripping stages using 20-pct HCI. Results are also given for tests using other extractants and stripping agents.

Jan 1, 1982

By E. J. Gleim

An important phase in the Bureau of Mines investigation of electrical machines designed for operation in gassy coal mines is testing enclosures of electrical components for explosion-proof qualities. In brief, this testing consists of filling and surrounding the enclosure with an explosive atmosphere of methane and air and then igniting the atmosphere within the enclosure to determine (1) Whether the resulting explosion is confined without discharge of flame; (2) whether the enclosure walls are permanently distorted; and (3) whether excessive pressures are developed within the enclosure. Ordinarily, the pressures encountered in routine testing do not exceed 100 pounds per square inch gage. Hence, the designer of the machine does not have too much difficulty in taking corrective measures to prevent flame discharge and distortion of the enclosure. Occasionally, however, the explosion pressures greatly exceed 100 pounds. Then the goblet of the designer may not be solved so readily, From experience over the year 0, the testing personnel often can predict that certain construction will result in high. Pressures, but, only in a very general way, has it been possible to advise designers what modifications might be made to reduce the explosion pressures to normal values. For example, if high pressures were developed in a motor starter having a partition with an opening through it, some enlargement of the opening may appear to be the logical procedure, but it has not been- possible to give information concerning the exact amount the opening should be enlarged to prevent development of high pressures .

Jan 1, 1952

By Thomas P. Meloy

"This paper presents an interim progress report on our recently begun research project on respirable dusts. We are reporting on a sophisticated, predictive, probably correct, testable hypothesis that postulates a mechanism by which some natively cytotoxic respirable size mineral particles, such as kaolin, are not harmful to the lungs, while other equally cytotoxic particles, such as quartz, are, even in small quantities, very harmful. In essence the hypothesis predicts that some mineral particles, not normally present in the earth's ambient dust, causes the lungs dust defense mechanisms to turn on the lung and harm it. However fruitful the hypothesis may be, it is a hypothesis and much work remains to be done before it can be accepted as a theory.While I may make the presentation and be the PI, my co-PI, Dr. William Wallace of NIOSH, has and will continue to make at least as much contribution to the project as I. Our sophisticated hypothesis is deeply scientifically based and unfortunately, in spite of the multifacited aspects of this project, there is virtually nothing in the literature to guide our work. This means we must go back to the classical physics to develop the models for calculating the powerful electrical effects near particle edges, and we must measure the fundamental biological constants associated with pulmonary macrophage. While there are daily discussions on Boltzman distributions, Einstein's Brownian Motion paper, the Nernst Equation, and sophisticated semi- in vivo biological time constant measurements, we are aware that this is not an easy problem and we are not likely to have irrefutable closed solutions to these problems by next Monday morning.HypothesisLet me now turn to our hypothesis. In order to occupy all the naturally occurring surface areas on the earth, man, during his long evolution from fish, had to evolve effective defenses against all the naturally occurring cytotoxic rcspirable mineral dusts. For example, clays, which are often the main component in naturally occurring respirable mineral dusts, are quite cytotoxic but do not harm the lung. However, for respirable mineral dusts that contain significant amounts of nonnaturally occurring but equally cytotoxic quartz and asbestos particles, the body has not had to evolve- an effective defense mechanism, and thus respirable mineral dusts containing these particles may harm the lung. Our hypothesis is, therefore, that a few nonambient minerals such as quartz, cause the bodies dust defensive system to harm the body in a manner analogous to Lupus or MS, diseases of the immune system."

Mar 1, 1989

By F. R. Lee

This publication lists permissible equipment approved by the Bureau of Mines during 1967 and 1968 (calendar years), except breathing apparatus and explosives. The purpose of this publication is to inform the public about approved equipment for use in underground mines.

Jan 1, 1970

By Ann G. Kim

Methane in coal constitutes a serious hazard in coal mining. Draining the methane in advance of mining can mitigate this hazard, conserve energy, and offer economic benefits. This Bureau of Mines report evaluates the Pittsburgh coalbed in Greene County, Pa., to determine if advance drainage is feasible. The gas content of virgin reserves in Greene County is estimated at 100 to 200 ft3/ton, a total of over 370 billion ft3 of gas in an area approximately 310 mi2. Because of the similarity to natural gas, drained coalbed gas could be recovered and added to pipeline supplies of natural gas. The value of conserved gas would offset the cost of drainage and extend energy resources.

Jan 1, 1975

By D. G. Kesterke

The electrolytic reduction of uranium dioxide to molten uranium in fluoride baths at approximately 1,200° C was demonstrated. Electrolyte constituents were BaF2, UF4, and either MgF2 or LiF. Preliminary laboratory-scale experiments were made in which the uranium oxide was added continuously for 3 to 5 hours to the cell during electrolysis. Over 1,000 grams of metal of 99-8 percent purity was made in some tests, Major impurities were aluminum, barium, iron, silicon, carbon, and oxygen. The effects of cell design, geometry, and bath composition were investigated. Electrode arrangement was the most important factor in cell performance.

Jan 1, 1963

By Laurence G. Britton

Accurate flammability and ignitability data for chemicals form the cornerstone of procedures used to assess the hazards associated with commercial chemical production and use. Since 1967 the ASTM E27 Committee on the Hazard Potential of Chemicals has issued numerous, widely used consensus standards dealing with diverse testing and predictive procedures used to obtain relevant chemical hazard properties. The decision to issue a standard rests solely with the membership, which consists of representatives from industry, testing laboratories, consulting firms, government, academia, and instrument suppliers. Consequently, the procedures are automatically relevant, timely, and widely applicable. The purpose of this paper is to highlight some of the widely used standards, complemented with hypothetical but relevant examples describing the testing strategy, interpretation, and application of the results. A further goal of this paper is to encourage participation in the consensus standards development process. The paper is published in two parts. The first part (in the preceding issue of Process Safety Progress) dealt with the E27 standards pertaining to thermodynamics, thermal stability, and chemical compatibility. The second part, published here, focuses on the flammability, ignitability, and explosibility of fuel and air mixtures. © 2005 American Institute of Chemical Engineers Process Saf Prog 24: 12?28, 2005

Jan 1, 2005