Search Documents

By Kenneth E. Hjelmstad

In situ leach mining operations often encounter difficulty maintaining adequate leach solution flow into the are formation. Swelling and dis-persion of clay particles in the formation are often responsible for this permeability loss. Permeability and leaching tests were done in the laboratory on clayey ores to evaluate a clay-stabilizing polymer's effectiveness in preventing these problems. Test results indicate that treating the ores with the stabilizer could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability-leaching tests. Since in situ leaching throughput rate is directly related to permeability, these results also indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure. To determine the reasons for the success of the clay stabilizers, an investigation was conducted to cieter-mine the effect of the stabilizer on clay swelling and dispersion. Clay-swelling tests indicated that the clay stabilizer reduced clay swelling. Zeta potential measurements made on fine clay particles treated with the stabilizer were compared to measurements made on untreated particles and indicated that the stabilizer was electropositive and, therefore, could reduce the degree of negative charge on the particles and their tendency to disperse or migrate.

Jan 1, 1984

By Robert W. Freedman, Robert L. Craft, William G. Humphrey

As part of a continuing effort to reduce the weight and bulk of equipment that mining personnel must carry underground, the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) investigated accurate and convenient gas samplers for use by mine inspectors in sampling mine atmospheres. The samplers are septum-stoppered glass vials commonly used for routine blood sampling. These lightweight, compact samplers yield results comparable with those obtained with conventional bottle samplers of 250-ml nominal capacity.

Jan 1, 1975

Develop geophysical techniques suitable for enhancing miner safety. Specifically, to use geophysical methods to detect hazardous conditions in a rock mass in deep underground mines as well as to assess the mechanical integrity and monitor changes of the rock.

Jan 1, 1997

By R. G. Nelson

This report covers investigations of the Bureau of Mines for the period of June 15, 1952, to June 15, 1953, on a research project for the Materials Laboratory, Wright Patterson Air Force Base, Dayton, Ohio. The primary purpose of this investigation was to make high-purity chromium-base alloys having room-temperature ductility and high-temperature strength. The Nonferrous Metals Branch of the Bureau of Mines, Albany, Oreg., has, during the past 7 years, developed on a laboratory scale a hydrogen treatment method for making high-purity chromium that can be fabricated into thin sheet and wire. This material can be bent at room temperature. The object of this investigation was to use this material to develop improved chromium-rich alloys for high-temperature uses.

Jan 1, 1955

By Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines has successfully tested a method to simulate methane (CH~) flows from face areas through the returns of noncoal mines. This technique' involves releasing a small quantity of tracer gas at a working area and sampling for that gas downstream in the re- turn airways. By measuring the dilution of the tracer gas, the dilution of any volume of CH4 released at the face can be calculated. This information is useful in selecting locations for CH4 monitors and in deciding the necessity for permissible equipment in the returns.

Jan 1, 1984

By M. S. Seehra, R. S. Pandurangi

"INTRODUCTION Silica and kaolin (a layer aluminosilicate) are among the major constituents of most coal mine dusts.' Whereas kaolin is cytotoxic in vitro but nonfibrogenic in vivo in humans and experimental animals,2-4 the cytotoxic and fibrogenic potential of silica is rather well established.5 Wallace and co-workers 6-8 have studied the cytotoxic potentials of both native and surface-modified silica and kaolin and inferred that retoxification is slow in the case of occluded silica vis-à-vis native silica. Recent epide¬miological studies indicate that silica concentration alone in a mine dust, as determined by transmission IR spec¬troscopy (TIRS), does not correlate well with the pro¬gression of coal workers' pneumoconiosis. 9 This obser¬vation has led to the suggestions that silica particles occluded by clays such as kaolin may not be fibrogenic. This proposal requires accurate estimations of kaolin, silica, and occluded silica. The current method of silica analysis in a mine dust sample employs TIRS of the 797- cm -1 band of silica, although its accuracy, as well as that of x-ray diffraction studies, is no better than 25 % , even in a laboratory-generated dust.° In this paper we have employed the techniques of diffuse reflectance spectros¬copy (DRS) and photoacoustic spectroscopy (PAS), in conjunction with an FT-IR spectrometer, for the quan¬titative determination of silica in laboratory-generated silica-kaolin mixtures.One of the main advantages of DRS and PAS is that, in these techniques, problems arising from sample prep¬aration of the KBr-based disks used in TIRS are avoided. There are, however, several other considerations (e.g., particle size effects and saturation phenomenon) which complicate the use of DRS and PAS for quantitative work. 10-25 In this paper, we have carried out a systematic comparison of the quantitative abilities of the two tech¬niques, as applied to the silica-kaolin mixtures, with par¬ticular attention to the saturation behavior of several bands with different absorption coefficients. In particular, we show that a weaker band for silica at 1875 cm-1 is suitable for quantitative purposes, and that quantitative accuracy is higher in DRS than in PAS. Details of this work are given below."

Mar 1, 1992

By Robert E. Barieau

This report gives the principles of the method used by the Helium Research Center of the Bureau of Mines when solving nonlinear-regression problems and contains the mathematical equations necessary to accomplish the following objectives: the evaluation of the parameters in such a way that the sum of the weighted squares of the residuals of an experimental observable is a true minimum, regardless of the functional relationship between the variables and these parameters; and the evaluation of all variances and covariances of the parameters by means of the usual approximation of the law for the propagation of errors.

Jan 1, 1967

By Jerry T. McLendon

The proper disposition of phosphatic clays has been the subject of research and debated for years by phosphate producers, State and Federal research agencies, regulatory authorities, and environmentalists. To date, no "universal" solution exists for the ultimate disposl of phosphatic clays. This Bureau of Mines report examines the state of conventional clay disposal technology and reviews the technical progress of innovative alternatives. Twenty impoundment sites were investigated by the Bureau of Mines using geotechnical methods and laboratory analysis of cored samples. In addition, quasi-static cone penetrometer soundings were conducted to define clay and/or sand-clay interfaces en masse. Samples of the top, middle, and bottom hole segments were obtained at each station for laboratory studies of clay densities, pore fluids, plasticity, and mineralogical properties. The results of this study support the continued use of initial clay settling impoundments but emphasize the need for "in-line" systems to reduce the initial volumes of plant-generated phosphatic clays. The effective use of sand tailings is also encouraged to promote further consolidation of clays via self-weight stressing, sand-clay admixtures, and/or surcharging sand caps.

Jan 1, 1984

By K. J. Miller

Electrophoretic mobility measurements of coal and pyrite particles in distilled water revealed a difference between the migration speeds of the two materials toward the anode in a dc electric field. This information led to the development of a laboratory electrophoresis column for separating fine pyrite from coal by utilizing the electrokinetic and the specific gravity differences between coal and pyrite. The study demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis using a stage separation technique. In a cost analysis, electrical power for electrophoresis was extrapolated to about $1 per ton of clean coal product. But, since the only successful tests ever made were in the laboratory with prewashed samples of minus 100-plus 325-mesh coal in distilled water, the cost figure derived is not representative of conditions prevalent in commercial coal cleaning operations. True conditions would reflect costs many times as great. In the course of the work, several scale-up techniques were considered but their feasibility became academic in view of the physical and economic problems associated with electrophoretic separation of pyrite from coal. Although the process and apparatus were finally deemed impractical for commercial coal preparation, the electrophoresis column may have some application as a laboratory device.

Jan 1, 1974

By J. B. Gayle

Oven widths for experimental and commercial slot-type ovens differ appreably in most instances; the experimental ovens usually ranging from 10 to 14 inches and the commercial units from 14 to 21 inches. Application of results obtained with experimental ovens to commercial practice thus requires major extrapolations. A critical survey of the literature indicated that sufficient information about the effects of variations in oven width on the carbonizing process is not available to permit such extrapolations to be made with any considerable degree of confidence.

Jan 1, 1960

By J. G. Kirby

The total number of petroleum refineries in the United States decreased during 1951, while the total crude-oil charging capacity continued to increase. There were 350 refineries as of January 1, 1952, compared with 357 a year earlier, according to the annual Bureau of Mines capacity survey. A gain of 369,241 barrels in daily refinery crude through-put capacity during 1951 brings the total to 7,332,885 barrels daily. The capacity of the average refinery to process crude-oil was 20,951 barrels daily, an increase of 1,445 barrels daily over the previous year. Capacity added in the Texas Gulf district accounted for 36 percent of the total increase; the Indiana-Illinois-Kentucky district, 23 percent; the East Coast district, 19 percent; the Oklahoma-Kansas district, 12 percent; and the Texas Inland district, 11 percent. The California district was the only one reporting a decline in crude-oil refining capacity, the total being 14,200 barrels daily below the previous year. Reported as under construction January 1, 1952, was an additional crude-oil capacity of 282,680 barrels daily, an increase of 77 percent over the January 1, 1951, total of 160,100 barrels. The capacity now building is for the expansion of existing facilities, since no new plants had been begun as of the first of the year. Three or four companies have plans to build refineries in the Williston Basin area of North Dakota, but no definite locations or dates when construction will begin have been announced.

Jan 1, 1952

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract SO122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine. Field testing was conducted during the last week of November 1972, at a coal mine operated by Inland Steel Company, near Sesser, Ill, and in the Robena No. 1 Mine, Waynesburg, Pa, on 12 March 1974. The tests included uhf propagation losses and noise (200 MHz to 1 GHz) in the Sesser, I11 mine location and vlf propagation loss and noise (1 to 200 kHz) in both of the above locations. The basic experimental parameters were frequency, polarization, antenna type/orientation, and distance. The following reports treat the various aspects of the test programs in detail. Since different antenna configurations were used in the two mines, each report contains its own experimental predictions drawn from its corresponding test activities. A test equipment list and block diagrams of typical experimental setups for the tests of section 2 are contained in appendix A.

Jan 1, 1974

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,857 samples, representing the products of 103 companies. The samples were collected during June, July, and August 1955. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1956

By Franklin B. W. Woodbury

The Bureau of Mines undertook the development and evaluation of a system to provide a simultaneous, on-line determination of both iron and silica in iron ore beneficiation streams as part of a program to improve the efficiency to mineral separation processes, Californium-252 (252-Cf) was the neutron source used in the system for measuring the amounts of silica and iron in bulk slurries by thermal neutron capture-gamma ray spectra analysis. The theory of thermal neutron capture-gamma ray reactions and their potential application to mineral processing stream analysis is discussed. The prototype system and supporting software developed by the Bureau is described. During the initial phase of the work, both simulated and actual pilot plant slurries were investigated using a 60-to 32-µg 252-Cf neutron source. The percent solids of the slurries was ranged from 2 to 40 percent and the silica and iron content ranged from 1.5 to 83 percent and from 10 to 65 percent, respectively. Accuracy of the determination of the components in the solids was dependent upon the percent solids in the slurry.

Jan 1, 1980

By Sathit Tandanand

This report presents a Bureau of Mines study on the time-dependent behavior of coal measure rocks for future implementation in stability analysis and safety evaluation of in-mine rock structures. This initial study focused on moisture adsorption rate and strength degradation of shales in Pennsylvanian coal-bearing strata in the Illinois Basin. A reaction of clay minerals in Illinois shales with atmospheric water vapor was hypothesized as the adsorption and strength degradation mechanism. Part of energy exchange between shales and the environment was attributed to a free energy controlled by pore pressure of the rock and partial pressure in the environment. The relationships between adsorption versus time and strength degradation versus moisture content were derived and correlated with the experimental data. Partial saturation at various levels of relative humidity occurs within approximately 2 weeks at room temperature. The strength of shales tested decreases linearly with increasing moisture content. When the moisture exceeds 7 pct of the dry weight, these Illinois shales become unstable. To this end, the moisture content is a good predictor of rock strength for shales.

Jan 1, 1987

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By Lloyd Williams

1. This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By R. R. Brown

The Bureau of Mines undertook a limited feasibility study to determine the practicality of removing copper from automobile scrap by thermal treatment. Test specimens, prepared by wrapping bare and insulated copper wire around small steel coupons, were heated at 600° to 1,150° C in various atmospheres for different lengths of time under both static and dynamic conditions. The tests indicated that adequate removal of copper cannot be effected by thermal treatment of scrap above the melting point of copper. Tests showed that copper present in scrap as insulated wire is embrittled by thermal treatment at 800° to 900° C if the insulation contains lead, and that the embrittled copper is almost completely removed by a mechanical action such as tumbling. Also chemical pretreatment of specimens to effect embrittlement of copper and the magnetic separation of oxide scale were studied. Tests showed that bare copper can be embrittled by depositing waterglass (Na, Si409) on copper prior to thermal treatment.

Jan 1, 1968

By G. S. Scott

The flammability of trichloroethylene vapors in air has been determined in a 7-inch cyclindrical vessel. Saturated flammable mixtures were formed with air at atmospheric pressure between 30° C (86° F) and 82° C (180° F); the trichloroethylene concentrations at these temperatures are 12.5 (lower) and 90 (upper) volume-percent, respectively. Further study is necessary to assess the effects of different variables on the flammability of this material. INTRODUCTION Trichloroethylene (TCE) (ClHC = CCl2), sold under various trade names (Blacosolv, Perm-A-Clor, Tri, Triad, Triclene, Trivec, Tromex, Vapoclean, Vapoclor, Westrosol, etc.), is an important industrial chemical. A summary of its physical and chemical properties is given in table 1. It is used to degrease metals, leather, and textiles, to extract residual oils from vegetable oil cakes, for dry cleaning, and in soap. It is a powerful solvent for fats, resins, bitumens, rubber, sulfur, and phosphorus. Several explosions in which trichloroethylene was involved prompted an investigation by the Bureau of Mines to determine the conditions under which such accidents can occur.

Jan 1, 1963