Search Documents

A method is proposed for the evaluation of the influence of grout prestressing systems on the support resistance offered by timber packs. It is shown that, in order not to reduce the load-carrying capacity of timber packs, grout prestressing systems need to be at least as stiff as a single timber rise. The method was used to establish strength specifications for the grout prestressing systems to be used under non-seismic and seismic conditions. For non-seismic requirements, the 24-hour grout strength needs to be at least 1,7 MPa, and the 7-day grout strength 4,9 MPa. The investigation showed that the proposed strength specification is realistic in the light of current grout-strength capabilities. For seismic requirements, the grout strength needs to be at least 4 MPa and 8 MPa to prevent extensive damage to the grout during seismic events with a peak velocity of 1m/s 3 m/s respectively.

Jan 1, 1996

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

By A. P. I. Popoola, T. J. Olaniyi, A. A. Adeleke

"A laboratory froth flotation experiment was conducted on a low-grade carbonatite copper ore sample obtained from Phalaborwa in the Limpopo province of South Africa. The sample was a homogenous hydrocyclone overflow which serves as the feed to the flotation cells at Palabora Mining Company (PMC). The sample has an average copper assay of 0.59% with predominant copper-bearing minerals being chalcopyrite, bornite and cubanite. The carbonatite nature of the ore comes from the high content of calcium (28.85%) and magnesium (6.84%) minerals. Collectors used were sodium diethyl dithiocarbamate and potassium ethyl xanthate alongside Senfroth 38 supplied by Senmin. The results showed that at 200 g/t mixture of collectors (50:50), an optimum grade of 8.03% Cu in the rougher flotation concentrate was achieved at 74% recovery, while during the second flotation, 24.65% Cu was obtained at 74.4% recovery using a Senfroth 38 dosage of 6 L/t with 100 g/t mixed (50:50) collectors. The particle size and pH value of the pulp played a significant role in that the mixed collectors performed efficiently at pH above 8.3 and at room temperature while particle sizes greater than 53 µm were well concentrated when compared with those of less than 53 µm. INTRODUCTION The need for copper ore concentration research is on the rise as a result of the depletion of deposits and the advent of low-grade copper ores. Although most copper ore deposits have other valuable minerals that support their economic extraction, the increase in technological innovations as regards copper usage and applications has increased the demand for copper. Several factors influence concentration results in a froth flotation column, of which the reagent used is most influential."

Jan 1, 2015

By B. E. Ydstie, B. F. Lund, K. R. Løvåsen, B. A. Foss

The paper presents sensitivity analysis for a dynamic model of submerged arc silicon furnaces. The model we study, called ?Simod?, was developed by Elkem in cooperation with NTNU and Sintef. It is today a much used tool in Elkem for operator training and analysis of the dynamic behaviour of the silicon production process. The aim of our work is to bring the simulator tool closer to industrial practice, and construct a mechanism to adapt the model to the behaviour of a running process, online. The paper presents the results of the sensitivity analysis that has been undertaken for important parameters in the Simod model. The parameters associated with the process inputs are electric power loss, loss of fixed C and reactivity of carbon. The output signals that have been investigated are fed quartz, tapped silicon and silica. The paper also interprets the results of the sensitivity analysis in a process operation context.

Jan 1, 2004

By J. W. Latilla, J. J. van Wijk

A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. Une cassure de taille en avant des unités de soutènement s’est produise sur la veine numéro 4 dans le puits numéro 3 (Matla 3) de la mine Matla Coal en avril et mai 2002. Les conditions d’extraction étaient extrêmement difficiles sur une distance d’environ 150 m dans la voie de tête et, en moindre mesure, sur le front de taille lui-même. L’étude présente analyse les raison majeures pour les conditions de grandes contraintes qui ont conduit à la cassure de taille, à savoir l’existence d’un mur de dolérite de >20m proche de la surface et l’effet d’arrêter la longue taille sur la veine 5 superposée. Les difficultés rencontrées pendant la cassure de taille sont rapportées, y compris les effondrements de piliers et toit dans la voie de tête, les aires de grandes contraintes en avant du front de taille causant des problèmes de stabilité pour le toit et les parois latérales, l’injection de roches cassées dans la taille en voie de tête, les cassures secondaires à mi-taille, et la disponibilité d’unités de soutènement critiques. Interventions minières réussies et leçons apprises furent : un angle de remblai de 14.6° était plus réaliste que celui de 20 à 25° utilisé auparavant pour prédire la conduite du mur de dolérite dans cet endroit ; tir à deux temps du mur a réduit considérablement les contraintes sur la taille et la voie de tête, ce qui a permis un travail de support complémentaire ; des types variés de support de piliers furent analysés et évalués ; la nécessité d’avoir toujours une trousse de première urgence disponible fut reconnue ; et finalement une stratégie pour les panneaux en dessous du mur fut

Jan 1, 2003

By J. A. Beukes, M. Marais

TICOR South Africa is a new titanium feed stock producer. In the Ticor South Africa plant the ilmenite feed to the smelter plant is roasted to enhance its magnetic properties. This allows for the magnetic separation of chromite from the ilmenite. The magnetization reaction relies on partial oxidation with both under- and over-oxidation causing insufficient magnetization. To subject the roaster plant feed material to the required physical conditions a circulating fluid bed (CFB) roaster is used. This paper describes the development of a laboratory model that will aid in the control of the CFB roaster.

Jan 1, 2003

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article thefollowing hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the of chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By S. Adams, J. R. C. von Holdt, J. L. Broadhurst

Fugitive dust from mineral extraction and processing activities can significantly influence air quality, the environment, and the health and quality of life of workers and surrounding communities. Poor engagement and communication between experts and lay persons, disciplinary silos and polarised viewpoints have made it difficult to develop a holistic understanding of the complex health issues associated with environmental emissions of mine dusts, and consequently to design meaningful and integrated approaches to address such issues. The collaborative Global Challenges Research Fund (GCRF) Mine Dust and Health Network, hosted by Minerals to Metals at the University of Cape Town, serves as a collaborative think-tank to inform research directions within and across disciplines, government policy and regulations, health monitoring programmes at public clinics, industry best practice, community healthcare and impact prevention programmes. It focuses initially on the southern African region, but with the intention to expand to mining-intensive developing countries within the rest of Africa, South America and Asia. This paper outlines the approach and activities of this global transdisciplinary and intersectoral network and presents some of the key outputs and achievements to date. Keywords: Mine dust, Global Challenges Research Fund Mine Dust and Health Network

Jan 1, 2020

By G. Vouille, P. Bérest

Residual stresses observed in rocks often result from non-compatible initial strains. These stresses can be determined when the incompatibility tensor associated with the initial strain tensor is known. The residual stresses in a cylindrical rock sample can be computed the sample is considered small enough for its incompatibility tensor to be constant. Les contraintes résiduelles, dont on observe couramment les manifestations dans les roches, résultent souvent de l’existence de déformations initiales non-compatibles. Ces contraintes peuvent être calculées lorsque le tenseur d’incompatibilité associé aux déformations initiales est connu. Les contraintes résiduelles dans une éprouvette cylindrique sont données dans le cas où le tenseur d’incompatibilité est constant. Eigenspannungen, die man haeufig in Steinen beobachtet, sind oft Ergebnis einer inkompatiblen Deformation des Anfangszustandes. Diese Spannungen koennen berechnet werden, wenn der Inkompatibilitaets-Tensor der Anfangsdeformation bekannt ist. Die Eigenspannungen einer zylindrischen Probe werden fuer Fall eines konstanten Inkompatibilitaets-Tensor bestimmt.

Jan 1, 2003

By R. Zivojinovic, S. Vujic

The structural age of the capital mining machinery, representing a part of the system of the Electric Power Industry of Serbia, has been dictated by the initiation and development of open pit coal mines. For example, the oldest bucket wheel excavators were installed some thirty-four years ago, and the average life of the relevant machinery exceeds twenty-two years. Operation of both capital equipment and machinery has direct effects on economic and business activities of open pit mines, and consequently forced us to make a decision and study thoroughly the problem of establishing the optimum exploitation life of capital mining equipment at the open pit coal mines of the Electric Power Industry of Serbia. The aim of this paper is to define and discuss the relative problems as well as to find out the possible solutions and establish the methodology for estimating the optimum exploitation life of machinery. The study was successfully carried out by a team of scientists engaged from and coordinated by the Department of Computer Science of the Faculty of Mining and Geology, University of Belgrade. This paper presents the key observations covering the subject problem. Keywords: Mining, Opencast exploitation, Coal, Optimization, Exploitation life, Capital machinery, Electric power industry, Dynamic programming.

Jan 1, 2003

By RT White

For many years the concept of life cycle costing (LCC) was promoted for decision making in corrosion protection systems. Nevertheless, the application of LCC was limited. Input data was often sourced from suppliers and met with scepticism. As a result final analysis was often insufficiently rigorous to meet the needs of Project Managers in sound decision making. The need for expediency often resulted in non-optimal corrosion protection system specifications. With improved communications and the global reach of industries, case history data, based upon actual performance has been able to provide input to substantiate decision making. However, today?s focus upon sustainability whereby environmental, economic and even social aspects enter into decision making has extended LCC into Life Cost Analysis (LCA). In an LCA analysis energy and environmental inputs into systems are compared as part of an overall assessment. The development of Agenda 21 at the Rio summit of 1992 has challenged the countries of the world to look at sustainable development in every economic activity. This ranges from construction to mining to electricity production to automotive production, use and disposal. The protection of buildings, infrastructure and transport systems is part of the needs of sustainable development. Zinc based corrosion protection has been an important part of the arsenal of the corrosion protection industry. This paper will highlight the use of LCC and the development of LCA with reference to the use of zinc based protection systems in a number of important industries.

Jan 1, 2006

By J. P. Gous, M. Tangstad, J. D. Steenkamp

In April of 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. One of the areas excavated systematically was the furnace taphole. The aim was to obtain a refractory wear profile of the tap-hole area, together with affected hearth and sidewall refractory. Subsequently, thermodynamic modelling was applied to quantify the potential for chemical reaction between refractory and slag and refractory and metal in the tap-hole area.

Jan 1, 2014

By S. Shi, X. Xia, F. Xuesai, Z. Shen, D. Han

The hydrodynamic characteristics of a mechanical flotation cell’s transportation zone have significant impact on its metallurgical performance, especially on coarse particles recovery efficiency. However, how to define and adjust the transportation zone was seldom investigated by researchers. In this paper a method will be introduced to define the boundary of the transportation zone by PIV measurement. It is found that the transportation zone can be extended upwards by enlarging the entire rotor-stator assembly from the bottom of tank and increasing the jet angle of the impeller. Two control methods have been validated in industry tests on KYF-160m3 and KYF-320m3 air-forced mechanical flotation cells. The result shows coarse particles recovery are both improved distinctly. It is suggested that enlarging the top transport boundary is able to helpful to reduce the floating distance of bubbleparticle aggregates, which contribute to improve coarse particle recovery in large flotation cells. Key Words: Flotation cell; Transportation zone; Coarse particles flotation

Jan 1, 2020

By J. L. Human, N. Fernandes

The rockfall hazard is the major contributing agency to fatal accidents in South African platinum mining operations. The majority of these accidents occur in close proximity to the working stope face. The collapse of fractured or blocky ground between individual temporary support units or the closest permanent support line to the stope face has not yet been adequately addressed. A large-scale stope support system testing facility funded by the Safety in Mines Research Advisory Committee (SIMRAC), has been designed and constructed to test support systems and stimulate innovative thinking by mining personnel, support manufacturers and suppliers by providing a facility where the interaction of stope support systems, a rigid stope face and a discontinuous hangingwall beam can be observed during quasi-static and dynamic conditions. Tests have been carried out on various types of stope support systems, focusing on the temporary support systems used in the immediate stope face area. The interlinking of the temporary support units with mesh or safety netting has been explored in the prevention of falls of ground between support units during gravity driven falls of ground. These tests illustrate the facility?s ability to be used to stimulate innovative thinking and provide a testing ground for the development of temporary support systems in order to reduce the risk off all of ground injury to mining personnel at the stope face.

Jan 1, 2004

By C. G. Anderson

Throughout the world, there are many orebodies or materials which have significant value but also contain arsenic, antimony, and mercury. As regulations on the transport, exposure, disposition and emission of these elements have become more stringent; it has become increasingly more difficult to derive the values from the resources. This paper outlines the fundamentals of alkaline sulfide hydrometallurgy and its successful application to arsenic, antimony and mercury bearing ores, concentrates, by-products, and other materials.

Jan 1, 2008

By I. Gil, J. -C. Roegiers

Abstract Hydraulic fracturing is a technology that has been utilized for more than 50 years in the oil industry. It was originally used for stimulating hard, brittle formations which typically exhibit low permeabilities and roughly linear elastic behavior. Nonetheless, an increasingly important segment of the industry is currently stimulating very soft and poorly consolidated formations; where the assumptions of ideal elasticity and relatively small fluid leakoff fail to hold (e.g. Gulf of Mexico, West Africa, Alaska, East China). In these rocks, hydraulic fracturing stimulation has been used for several years to control and solve critical production problems such as sanding and formation damage (caused during completion and drilling operations). Although successful1, the application of this method has not been accompanied by robust fracturing modeling techniques. In addition, long term production increases were often not materialized. In other words, engineers have been able, via trial-and-error, to avoid major ‘operational’ problems but with no optimization of such treatments. Thus, most hydraulic fracturing projects carried out in poorly consolidated rocks render unexpected results. A recent worldwide survey on net pressures by the Delft Fracturing Consortium (Papanastasiou, 1997) indicated that net pressures encountered in the field are 50% to 100% higher than the net pressures predicted by conventional fracturing simulators. The difference is yet higher for the case of poorly consolidated formations (Pak, 1997). The theory for the construction of a fully coupled elastoplastic three-dimensional hydrofrac simulator, specifically conceived for unconsolidated rocks, is presented in this paper. This novel model calculates the dimensions and changes in shape of the fracture(s) being created during hydraulic fracturing operations. No assumptions are made regarding either shape or geometry of the crack(s). Three main failure criteria are used simultaneously in this model: tensile and shear stresses, and volumetric strain. Incremental forms of the governing equations of equilibrium and fluid flow are presented. The scheme chosen for solving this problem is the finite elements method, which allows both equations to be solved simultaneously at any instant in time. Résumé La fracturation hydraulique est une technologie qu’a été utilisé pour plus que 50 ans dans l'industrie pétrolière. Elle a été utilisée au début pour stimuler les formations dure et fragile que typiquement ont des perméabilités basses et un comportement élastique à peu près linéaire. Néanmoins, un segment plus important de l'industrie stimule actuellement des formations mal consolidées; où les suppositions d'élasticité idéale et de relativement petite fuite de fluide ne se tiennent pas raison (par exemple le Golfe de Mexique, l'Afrique d'ouest, Alaska, la Chine de l'est). Dans ces roches, la stimulation avec fracturation hydraulique a été utilisée pour plusieurs années pour contrôler et résoudre les problèmes critiques de production comme les dommages de formation et d’ensablement (causé pendant les opérations de l'accomplissement et forage). Bien que prospère, l'application de cette méthode n'a pas été accompagnée de techniques robustes pour le modelage de fractures. En outre, les augmentations à long terme de production n'ont pas été souvent concrétisées. En d'autre termes, les ingénieurs ont pu, via le procès et l’erreur, éviter les majeur problèmes ‘opérationnel’ mais avec aucune optimisation de tels traitements. Ainsi, la plupart des projets de fracturation hydraulique ont été exécuté dans des roches mal consolidées et ont rendu résultat totalement inattendu. Une récente étude mondiale sur les pressions nettes par le Consortium Delft pour Fracturer (Papanastasiou, 1997) a indiqué que les pressions nettes qu’ont été rencontré dans le champ sont environ 50% à 100% plus hautes que les pressions nettes prédites par les simulateurs fracturant conventionnels. La différence est pourtant plus importante pour le cas de formations mal consolidées (Pak, 1997). La théorie de construction d'un simulateur elastoplastic d’hydrofrac à trois dimensions entièrement couplé, en particulier conçu pour les roches non consolidés, est présentée dans ce papier. Ce nouveau modèle calcule les dimensions et les changements dans la forme de(s) fracture(s) étant créé pendant les opérations de fracturation hydraulique. Aucune supposition n’a été faites en ce que concernant la forme ou la géométrie

Jan 1, 2003

By R. Flatabø, K-E. Johansen, L. Hunsbedt, P. M. Cowx, J. A. Bustnes

Eramet and Tinfos are two producers of manganese alloys in Norway, which have worked hard for several decades to improve both the internal and external environment. Furnaces producing ferro- and silico- manganese alloys generate large amounts of off-gas that contains substantial amounts of dust, heavy metals and organic by-products. The dust is separated from the gas in venturi scrubbers by washing with water. The water is cleaned and recirculated, and the surplus water coming from moisture in the raw materials, is discharged to the adjacent fjords after further treatment. Emission figures show that the discharge of suspended solids, manganese, zinc and PAH (polycyclic aromatic hydrocarbons) have been reduced substantially over the last three decades as a result of process improvements and installation of state of the art environmental control measures. The two plants were the first world wide to install mercury cleaning of the off-gases from the furnaces. Mercury emission reduction has exceeded 90%. Concerning other environmental issues, such as utilisation of off-gases for energy recovery and chemical purposes, both plants have achieved good results. Major effort in the environmental work has come from the plants themselves, but other players like FFF, The Norwegian Ferroalloy Producers Research Association, and SFT, The Norwegian Pollution Control Authority, have contributed to the achieved results.

Jan 1, 2007

By F. Crundwell, A. J. Lathwood

A number of base-metal operations would like to increase production to take advantage of the higher metals prices. In general, this higher production should not be achieved with major operating changes. In hydrometallurgical facilities, leaching and pressure leaching represents one area where upfront limitations may be a bottleneck to the capacity of the entire plant. An assessment of the capacity of the leaching tanks and autoclaves was performed using a predictive model within the AweSym flowsheet simulator. The model is described, and the results of the application of the model to a number of different leaching reactors are presented. It is argued that the leaching number, which relates the residence time, particle size and the leaching rate, is of prime importance. Finally it is shown that there are some unexpected catastrophic events in increasing production capacity without a thorough understanding of the leaching operation.

Jan 1, 2007

By T. C. Alex, K. M. Godiwalla, R. K. Jana

Manganese nodule, available in ocean beds, is a potential resource of the future for copper, nickel and cobalt. Recovering only these metals, containing less than 3% by weight, will result in the generation of large amount of residue. In addition to the material losses, several environmental and ecological problems arise out of this. The present study has been aimed at reducing the environmental and ecological problems associated with massive generation of this residue together with utilization of the resources. Presence of ~ 20% manganese and ~16% silicon in the residue has prompted us to check its suitability as a raw material for silicomanganese production. Lower manganese content and lower Mn/Fe ratio of the residue than that required for silicomanganese production has been corrected in this study by suitable blending. The efficacy of blending and its thermodynamic aspects using FACTSAGE software are discussed. The studies conducted indicate viability of bulk utilisation of the residue through silicomanganese production and thereby reducing the burden on environment to a great extent.

Jan 1, 2007

By I. E. Teymenson, L. A. Bakhvalov

Irrational usage of mineral commodities leads to depletion of natural resources and various ecological violations in natural environment. Fulfilment of a number of measures and strategic decisions by given problems requires a correct forecast of trends of social-economic systems. For solving the task of long-term forecasting special procedures, considering Kondratyev’s big cycles of world conjuncture, have been embedded into algorithms of unknown parameters identification and recovering of factors of different countries mineral resources production and consumption models. In the paper the classification of long cycles types, existing forecasting algorithms on the basis of Kondratyev’s ‘long waves’ or ‘K-waves’ and the modified algorithm, developed by us, which allows to reduce time and financial expenses and to improve the forecast quality, are presented. Furthermore, the article includes several forecasts of mining branch corrected models factors, received by us, permitting complex prognosis of economic and social development of different scale and control level systems. In the paper workability of proposed forecasting algorithms on the base of ‘K-waves’ and adequacy of created models to researched processes are proved.

Jan 1, 2003