Search Documents

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

By J. Tikka, E. Bäcklund, N. -O. Lindfors

Tornados are the most violent weather events in the world, and we have all seen the forces and phenomena created by tornados in nature. Airgrinder AB has been working with a material treatment technology, which most easily could be described as an artificial tornado. The process consists principally of one air fan providing a high-velocity airstream that enters a mechanical cyclone. When the gas enters the cyclone, an outer vortex is created. This outer vortex rotates next to the cyclone wall, and at the bottom of the cyclone funnel the gas stream is turned and an inner vortex is created. The control of the air flow is tuned by a special device on top of the cyclone. The gas outlet is at the top of the cyclone and the material outlet at the bottom. The material is fed through a feeding device into the air stream channel prior to the inlet into the cyclone. The process is basically an improved grinding and dehydrating system, which is very efficient and environmentally friendly and can even be employed with very sticky materials. Also due to its rotating comminution, the material particles become rounded during grinding, hence more free flowing and easier to handle. MEFOS has already tested more than 30 different applications in the pilot equipment. The materials tested range from metallurgical slags containing 2?3% moisture to sludges with up to70% moisture. This technology has a potentially strong impact on mineral beneficiation, including the drying of sticky fine-grained materials, improved and selective gas scrubbing and the manufacture of free flowing powders.

Jan 1, 2007

For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984. New President On 29th March, 1985, Mr B.C. (Bertie) Oberholzer, Manager of East Driefontein Gold Mine, was elected President of the Association of Mine Managers of South Africa for the ensuing year. Bullion from old film A pollution-free chemical method of producing silver that is 99 per cent pure-and therefore of bullion quality-from scrap photographic film and paper has been developed by a British company.

Jan 1, 1985

By A. Refahi

For predicting the energy consumption during the size-reduction process, the Bond approach is often used. In this work, the PFC3D discrete element method (DEM) software was employed to model the crushing behaviour of some rocks with different mechanical properties in a laboratory jaw crusher. FLAC3D software was adopted to analyze the stress distribution in the rocks. The rocks studied were modelled as granular assemblies in the shape of a sphere and/or a cube located between two jaws, and the work done by the jaws in the crusher was determined. Nine different types of rocks were studied and the energies consumed by the crusher were compared to those of the Bond comminution energy estimated from the Bond index. There is considerable difference between Bond crushing energy and work done by the jaw crusher for rocks. It appears that the Bond approach is not a suitable method for predicting single particle fracture energy done by the crusher. To verify the results obtained from DEM models, the fracture behaviour of the crushed rocks was examined and was compared to the PFC3D results. The tensile mode of fracturing is favourably modelled by the PFC3D software while the delamination mode cannot be well modelled by PFC3D software. Keywords: jaw crusher; discrete element method; crushing energy; Bond index

Jan 1, 2009

By R. T. Tshikhudo

Nanotechnology can provide solutions to many of the world?s socio-economic challenges. The application of nanomaterials for water treatment and analysis, point-of-care diagnostics and targeted drug delivery systems or devices could improve the quality of life for people in developing countries. Gold colloids have a long history (dating back to the 4th century AD) and are particularly well known for their aesthetic appeal and their therapeutic properties. Since Faraday published a report on the synthesis and properties of colloidal gold in 1857, a reasonable insight into the nature of gold sols (nucleation, growth and kinetics of coagulation) has been developed. Considerable attention has been drawn during the past few decades to the development and optimization of methods for the preparation of gold nanoparticles. In nanoscience and nanotechnology today, gold nanomaterials appear to be the most widely used material by both academics and industrialists. This is due to the extraordinary properties of gold nanoparticles (e.g. optical, catalytic, and magnetic?they are also known to act as strong Raman enhancers and may also amplify fluorescence under certain circumstances). Mintek, through Project AuTEK and the DST/Mintek Nanotechnology Innovation Centre (NIC), has been at the forefront of the development of new industrial uses for gold. Mintek?s gold nanotechnology programme focuses on the development of gold-based nanostructured materials and their applications in health, water and other related areas. While few projects use gold nanoparticles for water treatment and analysis, Mintek?s gold nanoparticles are widely used in the health sector. For example, gold nanoparticles are engineered and produced in large quantities as systems for targeted drug delivery. They are also used as tools for advanced rapid diagnostic tests. Both optical and electrochemical rapid diagnostic methods are developed for the human and animal health sectors for point-of-care testing. This paper gives a brief introduction and overview of gold nanotechnology, and desrcibes the development of some of Mintek?s gold nanoparticle targeted drug delivery systems and lateral flow point of care prototype devices.

Jan 1, 2009

By B. P. Watson

The discussion written by Dr de Frey suggests that mine design should be based on closely spaced stability pillars. However, this concept leads to low extraction ratios at depth. The concept of `crush' pillars in conjunction with more widely, appropriately spaced stability pillars allows for significantly larger extraction ratios, particularly at depth. It should be noted that the rock conditions in many areas of South African platinum and gold mines are good, allowing significant spans to be mined safely between stability pillars. `Crush' pillars are cut small enough to fail stably near the face under stiff loading conditions, and their residual strength is intended to support about 10 m rock height between stability pillars. While this support resistance cannot be achieved by conventional support, crush pillars have been proven to have the required capacity for this purpose. The concept of leaving smaller crush pillars with appropriately positioned stability pillars has been used successfully for more than 30 years in areas of South African platinum and gold mines.

Jan 1, 2011

By T. De Lange

Extensions to the beneficiation plant at the Grootegeluk Coal Mine are currently being planned in order to provide power station coal for Escom's Matimba Power Station, presently under construction. A simulation model was developed on the Olivetti M-24 microcomputer to facilitate the development of the envisaged flowsheet. The computer program simulates the heavy-medium separation and screening unit operations. The model is based on the construction of the Tromp partition curve described by an arctangent function, allowing ideal and non-ideal separations. The paper discusses the determination of the parameters required by the arctangent curve from standard process parameters such as Epm, Wolf cut-point, Tromp cutpoint and screening efficiency. The accuracy and shortcomings of the model are discussed, while an overview of the application of the model to evaluate borehole and bulk sample analyses is also given. It is concluded that the model is an invaluable aid to general flowsheet development.

Jan 1, 1987

By J. -M. Chautru

A geostatistical simulation of a typical mining site for polymetallic nodules in the North Pacific Ocean is presented. This is the first stage in the design of an industrial mining system. Two variables which have a major effect on the orebody's economic potential are considered, namely: the maximum slope of the ground inside a mining block of 50 x 100 m; and the average quantity of nodules on the same support. Two geostatistical problems have emerged in this study. The first is due to the lack of a change of support model for the maximum of a variable. A provisional solution, considering an experimentally accessible 'equivalent' support, is proposed. The second is due to a non-linear link between the two variables. To be able to take this into account in the simulation, we propose a new method based on the decomposition: X = E(X/Y) + Residue (X). Satisfactory results were obtained with this approach.

Jan 1, 1987

By R. J. Davidson

The mechanism of gold adsorption on activated charcoal by R. J. DAVIDSON: M.Se., Ph.D. (Rhodes) (Visitor) The adsorption of gold onto activated charcoal is most dependent on the concentration and character of the 'spectator' cations present in the adsorption medium. In the presence of calcium ions, gold is adsorbed as the calcium aurocyanide complex. The degree to which the aurocyanide complexes are adsorbed follows the series Ca> Mt:> H> Li> Na> K, calcium aurocyanide being the most stable complex and potassium aurocyanide the least firmly bound. If a loaded charcoal, where the gold is present as the calcium complex, is treated initially with either sodium carbonate or potassium carbonate solutions, the gold can subsequently be eluted from the charcoal with hot deionized water as either the sodium or the potassium complex respectively. The elution of gold with deionized water appears to be most attractive practically and economically, and has several potential applications in the recovery of gold from dilute solutions.

Jan 10, 1974

By M. McChesney

Modern materials for underground support* by M. McChesney The properties required of a support material for underground tunnels are discussed and, because concrete is both economical and easy to apply, a number of new reinforcing materials for concrete are examined with particular reference to these properties. From about thirty tests on different types of reinforced concrete, it is concluded that the addition of polymer to a concrete does not seem to influence the concrete's post-failure behaviour, and the on'y benefit to be achieved by this addition is to increase its flexibility (or to decrease it, depending on the polymer). Steel fibres tend to increase both the strength and stiffness of the concrete, but polypropylene fibres, although having definite loadcarrying capacities, provide non-stable failure, also known as brittle failure. The best result was obtained for concrete reinforced with steel wire: the post-cracking strength was very good and was maintained for a considerable deformation.

Jan 12, 1976

Prediction of the performance of explosives In bench mining by C. M. LOWNDS, B.Se. Hons (Rhodes), Ph.D (Cape) (Visitor) Some of the problems encountered in the calculation of the relative weight strength of explosives are discussed, and a realistic model of the behaviour of explosion products in a borehole is proposed. The heat flow from condensed to gaseous products is calculated as a function of time, and the relationship between the pressure and the volume of the product gases is found by a consideration of the compression of the rock between radial cracks. Work done on the burden is assumed to cease when the cracks first appear at the face. Reasonable values of burden and crack velocities are obtained from the model. Calculations of the relative weight strengths of aluminized mixtures of ammonium nitrate and fuel oil show that the increased density resulting from the addition of aluminium is the main advantage to be gained.

Jan 2, 1975

By H. W. Read

Sustained growth in demand for platinum group metals has resulted in an unfettered increase in new projects undertaken by the platinum producers. These projects are outsourced to various degrees. The argument of this paper is that both the client?s project manager and the consultant?s project manager are essential elements in the successful execution of a project. Their roles are not only different but also complementary, and are defined in the paper. Data gained from considerable experience in the South African corporate mining environment underpins the opinions expressed in the paper. Furthermore, an extensive literary search was undertaken to determine trends in related industries outside the South African context. Throughout the argument it is emphasized that project philosophy emanates from a systems view and must be treated as an overarching whole. The elements of project management become meaningless unless they are connected to one another and integrated into a cohesive unit. Advancing the knowledge field of project management is of critical importance to mining investors. There is no doubt that a key determinant of the sustainability of mining business is closely related to the efficiency of all-inclusive project management. From pre-investment and feasibility studies, implementation and execution, to ramping-up to full production, scientific project management has a critical role to play. Guidelines for the pursuance of this ideal are proposed. The introduction contextualizes the subject matter in an overview of the evolution of mine management in South Africa and abroad. Then, brief insight is given into the philosophy of project management. This exposition is confined to the predispositions, presuppositions and defining characteristics of project management. The core of the paper looks at the roles of the client?s project manager in relation to the consultant?s project manager. This section is underpinned by practical experience gained by the author on numerous mining projects. A view is taken of the future of project management in the mining industry. The conclusion summarizes the argument and aligns project management trends in the mining industry.

Jan 1, 2004

The 96th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 11th August, 1993. OBITUARIES The President announced the deaths of the following members of the Institute during the past year. Life Fellow E.F. Laschinger. Other Members R.K. Boright, J.S. Jacobi, R.D. Power, J.H. Cannon, C.J. du Plooy, L.B. Mcrae, C.P. Rossouw, A.L. Sillars, A.W. Heugh, R.K. Briggs, P.J. Stark, and C.S. Stott. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1993

By M. B. Cortie

An account is given of the development of ferritic stainless steels since their discovery in the early years of this century. The alloys became very widely used in the 1950s, the market during that decade being driven strongly by a demand for automobile trim made of ferritic stainless steel. The production of ferritic stainless steel declined as a proportion of the total at the end of the 1950s as consumer preferences changed. However, the market is now growing strongly again, this time driven by a demand for oxidation-resistant alloys for motor-vehicle exhaust systems. The tonnages produced, applications, and market shares of the various alloys are discussed and compared. Trends in world stainless-steel production, product forms, technological development, and usage are examined.

Jan 1, 1993

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

Deciding on plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g/t of fresh feed has been assumed a reasonable starting point with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2012

By Z. Botha

Sheryl Sandberg, the COO of Facebook, published a book titled 'Lean In', where she invites women to sit at the table. In summary, to 'sit at the table' entails not only embracing opportunity, but to actively seek out opportunities in leadership positions. Sandberg points out that, unfortunately, apart from institutional obstacles, a woman's own perceived limitations have a negative impact on her leadership ambitions. To create an environment where diversity will flourish, where everyone has a seat at the table and everyone has a voice, safety must be established first. To establish safety within a diverse team, there is power in relationships and connections. This study will first and foremost review theories in literature as to why diversity and inclusion are so important and the value that diversity brings to our industry. The study also recommends a few focus areas for improving diversity and inclusion in the industry.

Sep 1, 2022

United Kingdom mineral statistics 1977. Home, D., Squirrell, H. C., and Venkatesan, J. (compilers). London, Her Majesty's Stationery Office, 1978. 156 pp. £10,25. Copper mining and management. Navin, Thomas R. University of Arizona Press, Box 3398, Tucson, Arizona 85722. ISBN 0-8165-0586-1. 426 pp. Illustrated. Price Metal statistics 1967-1977. 65th edition. 1978. Metallgesellschaft AG, Reuterweg 14, D 6000 Frankfurt am Main, Fed. Rep. of Germany. 382 pp. Illustrated. Coal mine ground control. Peng, Syd S. John Wiley & Sons. ISBN 0-471-04121-1. 450 pp. Illustrated. £19.75 clothbound. Associate Professor and Chairman of the Uranium supply and demand: Proceedings International Symposium, London, July 1978. Spriggs, Michael J. and Casteel, Kyran D. (editors). Mining Journal Gemorfologiesewoordelys/Geomorpho logical vocabulary. Van der Merwe, J. S., en De Villiers, A. B. (samestellers).

Jan 1, 1979

The influence of Harold Hotelling?s work in the field of mineral economics is both unusual and outstanding. In the 66 years since its development, theory surrounding the economics of exhaustible resources has only been significantly researched since the early 1970s. At that time a wave of research into the economics of exhaustible resources arose from the threat of global resource scarcity and continued into the late 1990s. Current East Asian and global demand for natural resources as well as mineral and metal commodities, has stimulated interest in the optimal and sustainable exploitation of exhaustible resources to the point that the subject is worthy of review. Hotelling?s theory and the assumptions that he made in establishing a model for the optimal exploitation of mineral resources at the industry level and at the level of the individual mine owner, are examined. He showed that the rate of increase inexhaustible resource prices should be equivalent to the market rate of interest and that in a market with rising prices the rate of extraction should be constant. In markets where demand is stable optimal exploitation requires that the rate of extraction should decline over time, while in a monopoly market he showed that the rate of extraction is retarded. In addition, the effects of cumulative production on costs and prices, the uncertainty associated with estimates of the resource stock, the impact of exploration and issues of intergenerational equity are examined. An analysis of the optimal price path, extraction costs and mineral rents at an industry level is presented as a model. An analysis of the rates of production and optimal benefits at the individual mine level including total, average and marginal costs on the optimal rate of production, is considered. Optimal extraction rates for a mine with a clearly defined concave positive cost equation vary according to the position on the marginal cost curve. The influence of discount rates and the size of the ore reserves on the rates of mineral extraction are also examined and could define the frontier of usefulness for the ?economics of exhaustible resources?.

Jan 1, 2007

By and Z. S. Abisheva, Z. B. Karshigina, Ye. G. Bochevskay, A. S. Sharipova

The production of precipitated silica in the United States is about 145,000 tons of SiO2 and its prices vary significantly (from $ 1 to $ 4.5 per kg) depending on the area of its application. One of the most important parameters is its specific surface characterising dispersion (particle size and shape, presence or absence of pores), at a certain value of which the material acquires new properties and quality. At present, a technology has been developed for processing slag from phosphorus production to produce precipitated silica (‘white soot’) with a high specific surface and the possibility of extracting valuable components such as rare-earth metals (REMs) into a product enriched with them has been shown. However, the content of impurities in the deposited silicon dioxide, such as aluminum and iron, is above acceptable limits and may affect the quality of the final products. Therefore, along with the structure and specific surface, a very important characteristic of ‘white soot’ is the chemical purity of the material. In turn, calcium oxide occupies a significant share in the concentrate of rare-earth metals, which affects the content of ΣREMs oxides, which does not exceed 17.3 %. The low content of a valuable component may affect the feasibility of further processing. For the most complete utilisation of phosphorus slag, the authors propose a method for their acid processing, which allows for minimising the conversion of impurities to finely divided silica and collective concentrate, which will improve the quality of these products. Keywords: Phosphorus slag, precipitated silicon dioxide, rare earth metals, leaching, white soot, specific surface, technology

Jan 1, 2020