Search Documents

Mineral processing plant operators are faced with the necessity to choose between many different possibilities for plant improvement. Only a few such possibilities, however, can be tested on the industrial site. Steady-state simulators make it possible to assess the effects of several different flowsheet modifications in a few days, thus helping the process engineer to make his choice implement the solution that seems the most appropriate and check it. The example described here is the crushing and grinding circuit of the Shila Gold Mine, jointly owned by CEDIMIN SA and BUENAVENTURA SA, in Peru. Several possible modifications for the purpose of increasing capacity have been simulated and the results assessed in terms of technical quality, investment costs and energy consumption. The best solution indicated by the USIM PAC simulator was implemented and gave a 20% increase in capacity with a pay-back time of two months.

Jan 1, 1993

The segregation process has been known for many years and applied industrially for the treatment of various refractory copper ores. The principles of the process are briefly reviewed; the process was tested in the laboratory on two copper-cobalt oxide ores from Gecamines, Shaba Province, Zaire. Various parameters of the process, such as segregation temperature, dosage of reducing and chloridizing agents and flotation conditions were inyestigated. Experimental results have shown that the segregation of copper could proceed satisfactorily at low temperature (1000° K) but that of cobalt required higher temperature and higher additions of reducing and chloridizing agents.

Jan 1, 1992

By M. Polat

Variations in flotation rate by particle size and specific gravity have been investigated for three different bituminous coals. The flotation rates for various components were determined by separating the products of bulk flotation into size-specific gravity fractions. The effects of feed size and reagent addition on the flotation response of individual size-specific gravity fractions were evaluated.

Jan 1, 1994

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

By Andrew S. Prokopovitsh

The Bureau of Mines is concerned with all the approximately 60 industrial minerals, although its research program currently is focused on 10 of them--bauxite, chromite, clay, manganese, phosphate, potash, refractories, sulfur, titanium, and zirconium. To alleviate reliance on imported materials, particular attention is directed to those minerals having a potential for production from domestic resources. Another important consideration is environmental problems associated with the production of industrial minerals, principally in mining and mineral processing operations, The Bureau also is looking at the opportunities to substitute more abundant minerals for scarce raw materials such as rutile, fluorspar, and bauxite. In its overall minerals surveillance, the Bureau's mining and metallurgical research and development are coordinated with its minerals information activities from which reviews, projections, and forecasts identify the potential for critical disruptions and short supply situations.

Jan 1, 1975

By P. A. Meyer

The Tenmile Range is a north trending zone of high relief within the central Colorado porphyry-mineral belt, located between Leadville and Breckenridge. (Figure 1, the Index Map of the area surveyed.) The Climax mineralized zone is located at the southern end of the range on the northwest side of the Continental Divide. This portion of the total area surveyed will be discussed in detail today. A fixed wing aeromagnetic survey was flown over this range and mineralized zone in the fall of 1957. The survey was run as an experiment to see if a useful geophysical tool could be applied in the exploration for similar type deposits. The purpose of this paper is to describe the results of this survey and the approaches used to aid in the interpretation of the total intensity data.

Jan 1, 1968

By S. Todd Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty in factor of safety predictions for soil slopes where there is incomplete knowledge of the spatial distribution of soil properties. A case study considers a natural clay slope in Canada. The sequential indicator simulation technique is used as a means for generating a series of spatial maps of soil properties for this site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. Factor of safety determinations are then made for each simulated map using the simplified-Janbu approach, where the computations are performed with a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the distribution of factor of safety conditional to the type, position, and value of existing site characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1993

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By E. J. Wasp

An upsurge of interest in slurry pipelines to move coal from Wyoming, Montana, and Colorado to markets in the southwest, west, midwest and northwest has recently developed. Specific pipelines have been proposed to serve these markets; the routes of these lines are depicted in Exhibit I. It is, therefore, timely to discuss some technical aspects of the terminal facilities for these western coal pipelines. The discussion will be based on experience with the Ohio and Black Mesa pipelines as well as detailed planning and testing for a proposed 1,000-mile system from Wyoming to the middle south area. The economics of the pipeline terminal processes are heavily depend¬ent on site, type of process used, and other specifics of the situation. However, the following approximate breakdown of costs for a 1,000 mile, large capacity pipeline will be useful for orientation purposes. [Water supply 4 Coal cleaning 5 Feed preparation 10 Slurry transportation 72 Dewatering terminal 9 100%]

Jan 1, 1976

By Sureshan K. Moothedath

This paper provides a mechanistic representation for floc formation, growth and degradation and presents results from an experimental study of batch flocculation in which step changes were made in the impeller speed, flocculant addition, and slurry concentration. A discussion of the experimental results is included in terms of the mechanisms of floc formation and size-change.

Jan 1, 1993

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By Hajime Kitamura, Nobuharu Isago, Yuta Yamanishi, Kosuke Kawata, Hiroshi Yagi, Akira Matsuoka

Mountain tunnels are generally considered to be stable during earthquakes, however, it is known that the portal areas are prone to seismic damages. Characteristics in portals such as the location of the slope, modulus of ground deformation, and the change of overburden are different for each tunnel, and damage degrees are unclear. In this study, we reproduced the seismic behavior to investigate the effect on the tunnel portal by considering some parameters above, using simple static model tests and numerical analysis. As a result, the conditions of the slope condition and minimum distance from slope was confirmed to influence on the mechanical behavior of the tunnel portal during earthquakes.

Dec 1, 2022

By Marion A. Goudie

The Devonian salt basin, which contains the Saskatchewan Potash deposits, extends from just east of the foothills in Alberta, north as far as the Peace River area, across Saskatchewan and into Manitoba as far east as Range 10 west of the First Meridian and south into Montana and North Dakota. The basin is closed everywhere except to the northwest. The known potash deposits are confined almost entirely to the Province of Saskatchewan, with the exception of a small area in western Manitoba bordering the Saskatchewan boundary. The following discussion will concern only the Saskatchewan part of the basin. The evaporite series in the basin is defined as the Prairie Evaporite Formation of the Elk Point Group, of Middle Devonian age. Recent work done by potassium-argon dating methods has indicated an Upper Middle Devonian (Givetian) age of from 265 to 347 million years for the potash. The Elk Point Group consists in ascending order of the Ashern, Winnipegosis and Prairie Evaporite Formations. The Ashern formation, sometimes called the Third Red Bed, consists of dolomitic shales or shaly dolomites. The Winnipegosis is a reef type dolomite, usually with good porosity, and in many cases oil-staining, although to date no production has been obtained. The Prairie Evaporite formation consists of anhydrite overlain by halite and finally, in Saskatchewan, by the potash beds. In almost all wells which have been cored for potash the lowest potash bed is underlain by one or two bands of anhydrtte, which are used as marker horizons. Cores from a few wells which cored to the bottom of the salt series have shown flecks of potash throughout the halite.

Jan 1, 1959

By Martin Herenknecht, Michael Knabe, Ulrich Rehm

In Switzerland at present, the longest railway tunnels in the world, the Gotthard(57 km) and the Loetschberg base tunnel (34km) are under construction. For thischallenge six high-tech HERRENKNECHT Hard Rock Tunnel Boring Machines (TBM)are applied, which have to excavate approx. 80 km at the Gotthard and 20 km at the Loetschberg Tunnels. The machines being used are of a single Gripper-TBM type, which are equipped with the latest rock support techniques, in order to optimize the quality of the working conditions for the personnel which have direct impact on the quality of the tunnels. The different requirements of the projects based on different speci?cations within the tender documents led to completely different TBM concepts which will be reviewed in detail in this paper.

Jan 1, 2003

By B. F. Dickerson

STRATEGIC METALS! Recently, this money accented cry has been heard in such diverse locales as Mining company boardrooms, Banker's offices, Stockbroker's quarters, Swindler's dens and Congressional committee rooms. (In some cases, these locales are one and the same). Is the strategic metals rush for real? Should it be? Our paper attempts to give a very generalized view of the subject for a few metals, points to a few potential, but generally overlooked sources of these metals, and offers conclusions based on our studies.

Jan 1, 1981

By M. S. Celik

The principal impurities in some feldspar ores are titanium and iron which impart color and in turn degrade the quality of the ore. The mineralogical investigations indicate that titanium element originates from mainly rutile with small amounts of sphene. Conventionally, fatty acids and particularly sodium oleate are extensively used in the flotation of colored minerals from feldspar ores with reasonable success. In this study, new reagents, oleoyl sarcosine and hydroxamate have been used to float colored impurities before and after magnetic separation. Oleoyl sarcosine is found to exhibit better results compared to fatty acids and hydroxamate. The mechanism of the action is elaborated on the basis of experimental data.

Jan 1, 1999

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By D. P. Bryan

The identification and-develop¬ment of new construction aggregate resources, the most common mineral mined, is an essential need in this country's growing urban areas. In developing an aggregate exploration program, a thorough geological identification of all potential aggregate resources in an area is still of primary importance but other factors have also to be considered. These include physical properties, end product application, transportation and mining costs, and local government regulations including zoning. The present major aggregate producers are most likely to develop these future resources and are in the best position to initiate comprehensive exploration programs.

Jan 1, 1987