Search Documents

By K. A. Natarajan, J. M. Modak

A review of published literature on the biosorption of metals using nonliving biomass is presented. Factors such as pH, temperature, initial metal concentration, biomass loading, the presence of co-ions and the pretreatment of biomass influence the metal uptake by biomass. Although few generalizations are possible, unified theories regarding the mechanism of uptake are not available. Therefore, the above aspects of metal biosorption have to be defined individually for each biomass and metal-ion pair.

Jan 1, 1996

By R. R. Oder, R. J. Gray

We report measurements of the effects of rank, type, and grade of coal on grinding energy and grinding media consumption in a Pitt Mill. The rank of coal has a greater effect on grinding energy than does coal type. The effect of coal grade on grinding energy depends upon the relative grindability of the mineral matter and of the hydrocarbon components of the coal. The mineral matter is primarily responsible for abrasive media wear in a Pitt Mill. The widely recognized HGI test for coal breakage may yield misleading results, particularly for multiple-banded bright and dull coal where the screening procedure used in sample preparation favors the testing of the hardest coal fraction. The work reported here indicates that the Pitt Mill, which grinds the whole coal in a single stage and which yields easily interpreted results, is an excellent candidate for testing coal pulverization characteristics including energy requirements and equipment wear. The measurements of the effects of coal characteristics on grinding energy and on media consumption have been used to estimate the cost of fine grinding in a Pitt Mill. The results, based on a conceptual level evaluation of grinding at the rate of 1 TPH, show that there are trade-offs possible between the cost of energy and cost of media consumption which involve choice of grinding media size. The use of fine-size grinding media to lower grinding energy and to increase throughput can be deceptive because the total cost of grinding must consider both energy and media consumption.

Jan 1, 1992

By C. A. Rowland

The rising costs for and the possibility for limited availability of electrical energy are emphasizing the continual conflict faced in the selection of comminution circuits used in preparing ores for concentration, namely; capital cost vs. operating cost. Frequently, the circuit with the lowest capital cost is not the most efficient in the use of electrical power and wear resistant materials. The simplest circuit in terms of flow, pieces of equipment and capital cost is the single stage autogenous or partial autogenous circuit used to grinding primary crusher discharge or run of mine ore to the desired product size. (Fig. 1) From this circuit, complexity increases to multi-stage crushing circuits preparing feed for multi-stage grinding circuits. Fig. 2 showing a three stage rod mill ball mill arrangement is an example of a complex grinding circuit. Stage concentration further complicates the flow. Multi-stage circuits being the most expensive to install, often give the greatest operating flexibility and offer the best possibilities for the most efficient use of available power and wear resistant materials. Within available grinding circuits, other comparisons such as high speed vs. low speed mills, grate discharge vs. overflow discharge, metal liners vs. rubber liners, high charge vs. low charge, etc. all add to the conflict

Jan 1, 1977

By H. E. Wyslouzil

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favoured for this service due to the low capital and operating cost of the equipment, as well as improved metallurgical performance when compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1993

By V. de la Garza

The La Cienega Gold District is located at latitude 25°01'01"N and longitude 106°19'00"W, in the NW part of the State of Durango, Mexico. Ore deposits at The La Cienega District consist of a series of sub-parallel, NE-trending veins which cut andesitic and rhyolitic rocks that belong to both upper and lower tertiary volcanic sequences. The veins are vertical to steeply-depping structures which consist of quartz, generally containing gold-silver and less than ten percent lead, zinc and copper sulfide and sulfosalt minerals. Supergene enrichment is present on the upper parts of known oreshoots. Tertiary volcanic rocks of rhyolitic composition are the main host rocks of the gold-bearing quartz veins in the District. Gold productionc from the La Cienega orebody is scheduled to reach 100,000 ounces per year, becoming the largest gold-producing District in the Sierra Madre Occidental Province.

Jan 1, 1994

By K. Fotoohi

This paper presents a basic, and yet practical, three-dimensional finite element model that was developed by the authors for stress/stability analysis of mine structures. While the code is linear elastic at this stage, it has some practical features that make it an attractive tool for mine design. Such features include: simulation of mine backfill support, mining induced strain energy calculation, powerful out-of-core frontal solver and failure analysis by Mohr-Coulomb or Hoek-Brown failure criteria. Model development criteria are discussed, and the potential application of the model to mining is demonstrated by design examples.

Jan 1, 1998

By M. Karmis

Promoting a strong safety culture requires that the significance of unsafe acts be emphasized. This can be achieved vividly by accurate recreation of unsafe actions in the workplace, demonstrating explicitly how they resulted in a fatality or significant injury. Visual reconstructions of incidents can be realized today on personal computers. The approach described in this paper uses readily available PC software and hardware and results in output that can be presented to the intended audience using a variety of delivery methods. An actual incident involving a surface mining operation is reconstructed using Virtual Reality techniques. Use of the visualization approach to accident reconstruction as a training tool is discussed.

Jan 1, 2003

By J. H. Kempton

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes indicates that short-term predictions can bracket most parameters, uncertainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified. This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 1998

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

By William G. Fischer

Equations developed by an early researcher in subsidence, F. Martos of Budapest, Hungary, have been slightly modified to produce effective equations for predicting the time-dependent nature of Green River trona mine subsidence. Following the initial study, a survey was run to check the results twenty years after mining of the area had been completed. The final results were within a few centimeters of the value that had been projected. Mining conditions in the Green River area are ideal for this sort of study with trough type subsidence being the surface manifestation of high extraction underground room and pillar caving operations.

Jan 1, 1986

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, 'Where did Murray get this bit of philosophy?' Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper's Magazine in 1847. That's right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

By A. J. Sinclair

Los métodos de desmuestre para estudios de viabilidad dependen de las características geológicas del yacimiento que ha de ser evaluado. Se requiere un estudio geoestadístico preliminar, teniendo en cuenta los aspectos de autocorrelación de las variables sometidas a estudio, con objeto de que el plan de diseño de muestras pueda ser optimizado para producir las estimaciones de ley y tonelaje dentro de los límites de errores establecidos. En general, debe de tenderse a una distribución regular de muestras para ello, y longitudes regulares de las mis¬mas (a partir de los testigos o cortes, por ejemplo) son preferidas con objeto de facilitar los análisis estadísticos. Los planes de desmuestre son modificados y mejorados (bien técnica o económicamente) a medida que avanza el programa y es obtenida información adicional. Las muestras a granel para pruebas metalúrgicas pueden ser evaluadas en término de va¬riaciones señaladas por todas estas muestras en un depósito y la variabilidad de la ley dentro de las mismas. Una atención adecuada sobre estas fuentes de variabilidad asegurará una evaluación adecuada de los resultados de las pruebas piloto de las muestras a granel. Por otro la¬do, un estudio mineralógico general del yacimiento es un requerimiento importante, a veces ignorado, en una evaluación más general pero semicuantitativa de la representatividad de una muestra a granel; y, además, proporciona una información muy útil para optimizar el diseño de la planta.

Jan 1, 1982

By W. J. Miles

Oil based drilling fluids utilize a number of industrial mineral products to accomplish oil and gas drilling in several environments where water based drilling fluids are less effective or inappropriate. These industrial minerals include: organically modified bentonite, organically modified lignite, barite, hematite, mica, calcium chloride and other salts. A variety of organic products are also utilized in oil based drilling fluid formulations. Oil based drilling fluids are preferred in several drilling situations because: they can be used to drill through water sensitive formations; they produce holes that are very close to the drill bit gauge; they exhibit high temperature stability; they are more environmentally acceptable; they minimize producing formation damage; they provide faster drilling rates when used with new polycrystalline diamond drill bits; they minimize pipe sticking and lost rig time.

Jan 1, 1986

By Robert R. McDougal, Anne E. McCafferty, Bruce D. Smith

Magnetic, electromagnetic, and radiometric airborne survey data have been used in regional and local (drainage basin) scales. In a regional geoenvironmental assessment of the state of Montana, magnetic and radiometric data compiled from airborne surveys were used along with other digital geologic and geochemical data to prioritize mining districts for potential acid water generation. Probability ratio mapping was done in order to integrate the interpretation of many different digital data sets. On a more local scale, the Animas (CO) and Boulder Basin (MT) watersheds have been studied using helicopter geophysical surveys. The airborne geophysical surveys show many more structural features than the geologic maps. Combined interpretation of the geophysical data sets using the probability ratio method has resulted in identification of areas of alteration. Airborne radiometric data in the Boulder Basin area suggests that rocks with high potassium and thorium also have a high acid water buffering capacity.

Jan 1, 2000

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By G. Ferrara

Hydrocyclones and other dynamic separators are normally fed with pulps of water and solid particles. The particles have different sizes, shapes and densities and, except in the special case of mono-characteristic particles, are segregated into size, shape and density. Segregation is magnified by the high values of centrifugal acceleration in the hydrocyclones. This paper develops the theory of the segregation, indicates the major variables involved and reports experimental data of segregation under different operating conditions for mixtures of magnetite and/or ferrosilicon and non-magnetic minerals.

Jan 1, 1995

By A. Bruce Waugh, W. W. Wen, Kevin N. Clark, Neville C. Lockhart, Bruce A. Firth

Australia is the world's largest coal exporter, and technological advancement is a key element of the coal industry strategy. The issues include: increased recovery of saleable coal; enhanced quality, i.e. lower ash, moisture, fines, phosphorus (sulphur is a relatively minor problem for Australian coals); better quality control; higher throughputs/lower costs; improved handling and transport; and reduced environmental impacts. In process terms, many coal preparation operations, particularly fine coal circuits, are relatively inefficient, and all circuits must also be matched and integrated for optimum overall operation. A holistic approach to technological improvement is desirable. This paper summarises research and development efforts, within CSIRO and its collaborators, across the unit operations as outlined in the title.

Jan 1, 1995

By N. S. Tombs

This paper presents the experimental results of an ongoing investigation into various properties related to the performance and durability of concretes made using existing and new cement replacements. The process of cement and concrete production is investigated focusing on product performance and environmental performance. The overriding factor for the progression of a material will be product performance however; each material selected will have many intrinsic environmental benefits. The study combines Ordinary Portland Cement (OPC) with each cement replacement candidate using the most common replacement percentages, 10, 20, 25, 30 and 50 percent. A 35N/mm2 concrete is then prepared and analysed in the fresh and hardened state. In addition, a chemical and physical analysis of each replacement material has been performed and results compared to the control samples containing OPC only and Ground Granulated Blast Furnace Slag (GGBS) as a replacement. The results show that in their present form the replacements used in this research do not compare with the strengths achieved by the controls. The right balance of chemical composition and particle grading needs to be achieved to produce a realistic replacement material. The processes required to achieve this must strike a balance between monetary and environmental cost.

Jan 1, 2006

By A. C. Alexander

Chevron Resources Company owns and operates an open pit phosphate mine and mill 11 miles north of Vernal, Utah. The plant currently produces 500,000 tons per year of concentrate and has the capacity to produce 750,000 tons per year. The operation is currently being expanded to 1,300,000 tons per year of concen¬trate in order to supply a new fertilizer plant being constructed by Chevron Chemical Company in Rock Springs, Wyoming. A 10-inch, 96-mile pipeline is being built to transport the concentrate from Vernal to Rock Springs. The present and expanded operation will be discussed. HISTORY In 1915, Harry Ratliffe staked nearly 15,000 acres of low to medium grade phosphate rock along the southern flank of the Uintah Mountains. This deposit became the largest privately owned phosphate deposit containing approximately 700 million tons of reserves. Initial development of the deposit began in 1958 by San Francisco Chemical, a joint venture between Stauffer Chemical Company and Mountain Copper Limited. In 1968, Stauffer Chemical Company bought out Mountain Copper Limited and became sole owner and operator. In 1981, Chevron Resources Company bought the property from Stauffer and has operated the mining and milling operations since.

Jan 1, 1985