Search Documents

By Kim A. Lapakko, William W. III White

The ASTM standard method D 5744-96 was developed to provide a well-defined kinetic test protocol, conducted under controlled reaction conditions, with the intent of generating reproducible results. The US Bureau of Land Management, American Assay Laboratories, and the Minnesota Department of Natural Resources cooperated in a intralaboratory and interlaboratory testing of the protocol. Intralaboratory testing was conducted on duplicate samples of gabbro (8) and siltite-argillite (5) rocks for periods of 20 to 125 weeks. The difference between replica& intralaboratory pH readings on drainage from the gabbro for the drip-trickle leach alternative typically did not exceed 0.1 units, although differences as high as 0.4 units were observed. The difference from the mean for rates of sulfate, calcium and magnesium release was typically within 10%. Intralaboratory results for the siltite-argillite samples were generally similar, although a one unit pH difference was observed for one sample. Three different laboratories tested a gabbro sample for 125 weeks, with a maximum difference from the mean pH of 0.5 units. The percent difference from the mean for sulfate and calcium release rates was typically within lo%, although values as high as 30% were observed. Data on intralaboratory and interlaboratory agreement on the flood rinse alternative of the method were limited. Replication on the sample tested was comparable to of better than that observed for the drip-trickle method testing of the same sample.

Jan 1, 2000

By Jerome F. Thomas

The primary purpose of this paper is to review the fire and explosion hazards associated with hydrocarbons heavier than methane. Methane is the classical hydrocarbon encountered in mines whose presence is generally due to bacterial decomposition of organic debris. The higher hydrocarbons are more likely to be found during tunneling when petroleum products either natural or man made are encountered. Fires may be defined as rapid gas phase oxidations accompanied by the rapid evolution of light and heat. Explosions may be defined as uncontrolled fires. The rapidly expanding gases resulting from combustion exceed the speed of sound and generate percussive forces. The essential elements for a fire or explosion are shown on Figure 12: (1) a gas phase explosive mixture and (2) an ignition source. The paper will attempt to review various aspects relative to the explosive mixture; The concentration and composition; Techniques for detection; Techniques for ventilation to reduce concentration below explosive limits. The ignition sources are also listed on Figure 12. An arc originates from an electrical source such as electrical switches, relays and motor brushes. Static electricity can also be an arc source and may be generated by air flowing through rubber bases or a rapidly moving endless belt. A spark is generally associated with abrasion of iron metal. A flame source may be a match, candle. cutting or welding torch, or engine exhaust. If

Jan 1, 1974

By Allan J. Breitenbach

Heap leach operations provide a low-cost method for recovering gold, silver, and copper metals from low grade ore materials. The processed ore materials are stacked in controlled lifts on a lined pad facility for heap leaching. A controlled barren solution is applied to the heap ore surface by sprinkler or drip emitter irrigation, and ore metals are leached into the solution for collection and extraction in plant process facilities. The leach pad and solution collection facilities are lined with impervious materials for containment of all process solutions. The liner system typically includes a composite geomembrane and clayey soil liner with a protective drain cover fill to maximize solution recovery and protect the underlying groundwater conditions. This paper discusses the types of pad liner systems currently used by the mining industry and the "good, bad, and ugly" lessons learned in engineering practice over the last 10 years in the design and construction of heap leach pads.

Jan 1, 1999

By Y. B. He

The effect of the overflow to underflow (O/U) flowrate ratio of a dense medium cyclone on its performance is tested utilizing a 6" dense medium cyclone and density tracers. The results show that the O/U flowrate ratio is clearly correlated with the separation cut point D50, the separation efficiency Ep, the density differential 0, and short circuiting of the cyclone. Within certain limits, a higher O/U ratio results in a better separation efficiency, a higher D50 and an increased density differential. A lower O/U ratio, on the other hand, reduces the cut point shift and density differential. The phenomenon of short circuiting to the underflow, which is especially significant for fine particles, is directly connected with an excessively low O/U ratio.

Jan 1, 1992

By Raul Z. L. Cançado, Virginia S. T. Ciminelli, Roberto Galery, Armando C. de Araujo

Brazil is presently among the seven largest gold producing countries in the world. This paper discusses the evolution of gold mining through the history of Brazil. It also gives a general account of the present practices for mining, processing and extraction of gold. Flowsheets of some selected plants are presented. The environmental aspects involved with gold production are also considered.

Jan 1, 1987

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach, which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faithfully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach that assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared, using a petroleum resource estimation example.

Jan 1, 1994

By J. J. Moore, I. Iwasaki, L. A. Lindeke

Correlation of scale-up from small-scale batch laboratory mills to large-diameter industrial mills was established by performing two series of laboratory and pilot plant grinding tests using a magnetic taconite ore and a siliceous sulfide ore. In one series, controlled batch grinding tests in 203-, 508-, and 914-mm (8-, 20-, and 36-in.) diameter mills were carried out followed by a second series involving continuous grinding tests using 305-mm (12-in.) and then 1067-mm (42-in.) diameter pilot plant ball mills in open circuits. The effects of ball diameter on wear and of mill diameter on grinding power and ball wear are illustrated.

Jan 1, 1988

By Gerald H. Luttrell, Jaisen N. Kohmuench, Michael J. Mankosa

A new separator, known as the Hydrofloat cell, has been developed to overcome limitations of traditional flotation cells in recovering coarse particles. In this process, small air bubbles are introduced into a hindered "teeter" bed of fluidized solids to create light bubble-particle aggregates that can be separated based on differences in density. Laboratory tests conducted with coarse phosphate feeds indicate that the Hydrofloat cell is capable of increasing BPL recoveries by nearly 20% over conventional flotation methods. Based on these encouraging results, a pilot-scale Hydrofloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the plus 35 mesh plant feed can be increased by more than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the plus 16 mesh particles in the Hydrofloat concentrate. This article describes the theoretical basis for the development of the Hydrofloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 1999

By [Miroslaw] M. Hajdasinsk

The identification of the real internal rates of return (IRR's) of a project is essential for its economic evaluation. The existing methods for the calculation of IRR's are both cumbersome and unreliable, mainly because of their inability to effectively isolate the real IRR's and incapability of discovering multiple IRR's of even multiplicity. In this paper, a concept of the 'cash flow pattern tree used for isolation of the real IRR's of a project is presented. This concept, combined with the Sturm procedure for counting the real distinct zeros of a polynomial within a specified interval, leads to the development of a method and computer program for isolation and calculation of the real IRR's of a project. The method examines whether or not real IRR's exist, and if they do, isolates them within bounded and narrow intervals in a mathematically founded way. The isolated IRR's, whether simple or multiple, are subsequently calculated either directly or by means of an appropriate approximation procedure. Numerical examples assist the development of the method and the corresponding computer algorithm. Because any Net Present Value treated as a function of interest rate can easily be transformed into a polynomial, the method presented also constitutes a method for finding the real zeros of a polynomial.

Jan 1, 1986

By Christopher Newman, Robert Dupuy, David Newman

"The development of a multiple level underground mine is a complex task in which geology, engineering, ground control, and unit operations are integrated into a single mine design. The components are inter-dependent and must function cohesively to ensure a profitable underground mining operation. To optimize reserve recovery, mine planning should begin from the lowest level and progress up. This limits any misjudgments or oversights of a given level affecting the underlying levels and ensures the ability to maximize recovery from each level.Mine planning should start with the exploration and characterization of the geologic setting. Once the reserve geology and quality is well understood, then mine planning can begin with respect to the following:,Orientation of mine works with respect to horizontal stress,,Access to the reserve,,Determination of opening widths,,Selection of back, floor horizons and pillar centers,,Selection of development and secondary mining heights,,Appropriate interburden thicknesses, and,Examine the stability of the multiple level mine through numer¬ical modeling.The multiple level mine design process and decisions are presented through a case history example. The theme is that there is one opportunity to “get it right” as well as many chances to overlook a small aspect within the design that will plague the mine throughout all levels and through the entirety of its operating life.INTRODUCTIONAs surface quarries reach their economic stripping limit and encroach on mineral and/or reserve boundaries, they approach the end of surface mineable reserves. Furthermore, modern urban sprawl has placed previously remote surface quarries within suburban development and neighborhoods, leading to significant increases in noise, dust, and vibration grievances by the community and regulators (Newman, 2017). Many mining operations have begun year-round production of underground reserves to meet growing market demands. This does not permit the typical sequence of stripping overburden in the winter to provide limestone to mine during the construction season. Underground stone mining operations in the United States commonly utilize a room-and-pillar mine layout with drill-and-blast production methodology for the development of the reserve. Within the Midwest and Eastern regions, thick and flat-lying limestone formations lend themselves to the utilization of multiple level mining layouts. While a multiple level mine plan will increase the overall recovery of the reserve, greater overburden depths, multiple level geometry, and the presence of discontinuities all require an emphasis on ground control for the planning and development of a safe and productive multiple level underground stone operation."

Jan 1, 2019

By G. A. Parkison

The sequential copper analysis method is a particularly useful technique to semi-quantitatively define the geologic, mineralogic, and metallurgical types and zonations commonly associated with porphyry-type copper deposits. The method is based on the partial dissolution behavior displayed by the prevalent copper minerals malachite, chrysocolla, chalcocite, and chalcopyrite to solutions containing sulfuric acid and sodium cyanide. Results from sequential analyses of the sample and analytical residue using sulfuric acid followed by sodium cyanide and then aqua regia solutions when compared with conventional total copper analyses can determine the amounts of leachable oxide minerals, leachable secondary sulfide minerals, and primary copper minerals, respectively. Sequential assay analytical results and interpretation are presented for copper deposits in Chile, Mexico, and the United States.

Jan 1, 1995

By S. Yerel

Block cutter machines have been extensively used in natural stone industry, which is a sub-section of mining industry. In this study, the costs occurring in plate losses cut from Bilecik beige marble with a circular saw block cutter machine have been predicted using Statistical Process Control (SPC) techniques. One of SPC techniques is Shewhart control charts such as mean control chart. These charts have been efficiently at determining the plate losses. The costs occurring in plate losses have been calculated by using the result of Shewhart control chart. Finally, this study presents the necessity and usefulness of SPC techniques in assessment of natural stone industry.

Jan 1, 2010

By John E. Frost

The Gibralter Mines Ltd. complex is 61 km (38 miles) north of Williams Lake in central British Columbia, Fig. 1. The discovery of these deposits evolved in stages such that each stage revealed a bigger piece of the elephant. When the elephant was mostly revealed, Placer Development Ltd. brought the property into production. Although Gibralter is aporphyry copper deposit, it is certainly not a typical one. Copper and minor molybdenum mineralization occur in a foliated and saussuritized quartz diorite. Ore bodies tend to be tabular in form because foliation exerts a major control on localizing mineralization. A generalized geologic map of the Gibralter-Pollyanna area is shown in Fig. 2. Mineralization was first identified in 1917 in the Pollyanna area. Several shallow pits were sunk on flashy, but low grade, lenticular quartz veins. Duval Corp. made the initial commercial discovery, the Pollyanna ore body, on what were then called the Pollyanna claims. These claims, staked by R.C. Glen and C. Gennis in 1963, were the first to be optioned by Duval in British Columbia in October 1964. Placer Development joined Duval in late 1966 as a 50% joint venture partner, and after optioning the adjoining Gibralter claims, proceeded to evaluate and develop the four ore bodies that make up the Gibralter deposit. The Gibralter claims south of the Pollyanna claims provided the name for the Gibralter deposit.

Jan 1, 1991

By W. D. Diment

The concept of flying employees in and out of remote mine sites on a regular rotation basis, rather than establishing permanent support communities nearby, has gained increasing acceptance by mine operators, unions and regulatory agencies in Canada. The development of successful fly in/fly out programs and resultant compressed work schedules is dependent on meeting design requirements through comprehensive research of worker profiles to ensure the selection of suitable employees and the implementation of satisfactory working conditions. This paper presents an overview of Canadian mine industry practice with regard to the fly in/fly out mode of operation and compressed work schedules.

Jan 1, 1987

By Peter McKenna

A mineral rights holding can ultimately only be turned to account by the profitable mining of ore on that property. The evaluation of South African gold mineral rights properties must therefore be carried out by assuming that they have potential to form part or all of a future gold mine. Such analysis involves the simulation of many of the estimation procedures that are normally carried out in a full feasibility study of a new mining venture but using far less data. This paper describes in detail the evaluation procedures that may be applied to an individual property and then indicates how these techniques can be applied to a whole mineral rights portfolio.

Jan 1, 1989

By Roe-Hoan Yoon

Froth flotation is widely used for separating particulate materials from one another in aqueous media. The basis of this important separation process is to control the hydrophobicity of particles. However, it is difficult to predict the kinetics of flotation based on contact angle (?), which is a thermodynamic property. A solution to this difficulty would be to develop a relationship between ? and the gradient of the hydrophobic forces across the solid-liquid and bubble-liquid interfaces. Such information can be obtained using the surface force apparatus (SFA), the atomic force microscope (AFM), and the thin film balance (TFB). The present communication reviews the results of the measurements conducted using these methods, and offers a methodology for deriving a rate equation for bubble-particle interactions

Jan 1, 1999

By Yanchuan Li, Haifei Yao, Haiyan Wang

"Dust pollution is very serious in coal mining process, which is a great threat to the underground staff health and equipment and facilities safety. Coal seam water injection in mining process is an effective way to reduce coal mine dust concentration at the source. However, the effectiveness of water injection is limited in high-pressure and low-porosity coal seam. To improve the moisture content of coal seam, expand the wetting range and enhance the effect of dust reduction by water injection, the injectability and influencing factors of coal water injection are analyzed by numerical simulation method, and the sealing technology under high-pressure condition is studied. Then, according to the practical conditions of Tangkou coal mine, the parameters and process system of process system are designed, the effect of high-pressure water injection in coal seam was determined by testing water injection quantity, water increment and dust concentration. It is showed that the dust-removal rate of the high dust concentration operation such as falling coal and moving frame is 63.49% and 59.72%, the maximum dust-removal rate of multi-processes is 53%, which achieve a high level of application. The research results in this paper is of important theoretical and practical value to improve the water injection effect of high-pressure and low-porosity coal seam and improve the efficiency of dust removal in coal mining process.Introduction With the increasing of the depth and mechanization of coal mining, coal dust, the impact of ground pressure, ground temperature and other natural disasters continue to upgrade the harm degree (Wang 2011, Wu et al 2012), disaster incidents occur frequently, which seriouslythreaten the safe and efficient mining and the physical and mental health of underground staff. Coal seam water injection can effectively reduce the coal dust when coal crushing, prevent the impact of mine pressure, coal and gas outburst disasters, by increasing the thermal conductivity of coal, reduce coal temperature, and prevent spontaneous combustion of coal. In addition, coal seam water can soften the hard coal, so that speed up the recovery rate, improve coal production and efficiency (Wu et al 2008, Nie et al 2007). However, the coal seam in many mining area is with high-pressure and low-porosity feature, Coal joint cracks are not developed and relatively hard, water injection is difficult in these coal seams, then the desired disaster prevention effect cannot be achieved (Jin et al 2001, Zhao et al 2000). In this paper, the numerical simulation and field test methods are used to design the high-pressure and low-porosity coal seam water injection technology, so as to solve the difficult problem of coal dust control in high-pressure and low-porosity in deep well mining process."

Jan 1, 2017

By D. K. Dysinger

Capital resource budgeting is the means by which managers of publicly held companies fulfill their fiduciary responsibility to maximize the wealth of stockholders. Managers maximize shareholder wealth by allocating investment capital to the most productive of competing alternative projects in a manner that maximizes the net present value of the firm's future cash flow. The techniques of cash flow analysis are the primary tools available for selecting a corporate portfolio of projects that meets or exceeds the rate of return expected by shareholders. The reliability of cash flow analysis hinges on the ability of managers to forecast the future values of individual components. The accuracy and reliability of forecasting determine the soundness of capital investment decisions and, ultimately, determine the value of the firm. The present paper will explore tools for forecasting the spot market price of a commodity, silver, to demonstrate the difficulty and uncertainty involved in forecasting the future. The commodity price is only one of a number of components of the cash flow equation. Each component has a unique and uncertain future and must be individually analyzed and forecast to arrive at a robust cash flow model.

Jan 1, 1997

By R. P. Plasket, G. M. Dunn

The cobalt plant was successfully commissioned in mid-1983. It is located within the company's nickel - copper re finery situated in Springs, South Africa. Plant design, which began in 1981, made provision for the corrosive process environment, stringent environmental standards, and the latest noise abatement requirements. In addition, the process flowsheet for the primary recovery of the cobalt byproduct and the purging of six impurity metals (nickel, iron, copper, manganese, lead, and arsenic) was designed with simplicity as a primary objective. High purity cobalt powder has been produced since commissioning.

Jan 1, 1987

By G. Sanders

Discussion by G. Sanders The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominantlithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below. Missing the high-grade part of the ore body In your statistical analysis, you directly compare the reverse circulation assays to the diamond drill assays in Section 30. Two points argue against a direct comparison and suggest the differences are greater than the 3 % that you report. First, any core loss in a gold zone most likely means that the true gold values are greater. The drillers lost significant amounts of the clay-rich, Section-30 gold mineralization. Also, the initiated salt-mud system, an attempt to improve the core recovery, met with little success. Second, the practice of not sampling core geologically, but instead sampling on even 5-foot intervals, adds a deliberate dilution to the core assay values by including a portion of nonmineralized rock in the first and last samples of each high- grade intercept. The result is often a pair of low-grade assay values on either side of a high-grade gold zone. In reality, a high-grade gold zone has a very sharp assay wall that is often bounded by barren rock. This sampling method may make the diamond-drill core assays more like the reverse circulation values and may help explain the statistical similarities you found. However, it does not represent the true gold values in the high-grade parts of the deposit. You cannot deny that, by careful geological sampling of the drill core, higher and sharper assay values will be obtained. The low core recovery and the diamond-drill-core sampling method used act together to lower the diamond-core assay values. The 3% difference you found between the reverse-circulation and diamond-core assay values could be much larger when you consider what the true diamond-drill core values would be with optimum core recovery and a geologic sampling method for the core. Should statistics have been applied here? The statement "... that reverse circulation holes have overestimated the values of some ore zones and underestimated the values of others" (p. 345) is not correct. The subsampling confirmed what the cross sections hinted at in Section 30. Namely, beneath the high-grade zones, the reverse circulation holes created, by contamination, large intercepts of low-grade ore in regions of barren rock. Because the low-grade material was not there to begin with, this is not a process of overestimating low-grade mineralization. The next statement that "the average result is similar to that of the diamond drill holes" may apply to the data set numerically, but it is not true when viewed spatially on cross sections. Adjacent reverse circulation and diamond drill holes are almost impossible to correlate, high-grade zone values vary widely and many low-grade intercepts make no geologic sense. The subset sampling and cross sections presented in the first part of the paper show that the reverse circulation portion of the data set has some serious problems, as highlighted above, and should not have been dealt with statistically at all. Conclusion Each ore body is different, and each drilling method presents unique sampling problems. In this case, the diamond drill is the

Jan 1, 1994