Search Documents

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits, thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium. Key Words: Rhenium, Ammonium Perrhenate, Extractive Metallurgy

Feb 27, 2013

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground-fall-related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground-fall-related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 25 longwall mines were visited representing nearly 50% of the currently active longwall mines representing all of the major US longwall-producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. Results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices presented by this author at the 2017 Society for Mining, Metallurgy, & Exploration Annual Meeting. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries.

By R. Hipsley, D. Arbonies, P. J. Dobak, M. Visher

The Storm deposit is a high grade breccia hosted “Carlin-type” gold deposit located at the north end of the Carlin Trend. Storm consists of 3 smaller deposits: 1) 49er Zone, 2) End Zone, 3) Discovery Zone. Structural intersections and favorable stratigraphy at the Paleozoic Popovich/Rodeo Creek formation and Bootstrap limestone formation contact are the primary known controls to gold mineralization at Storm. High grade silica-sulfide breccia occurs in the footwall of the north-south trending, dike filled, Dee fault. This mineralization cross-cuts silicified heterolithic breccia zones localized above the Bootstrap limestone where northwest, dike filled, reverse faults cut this structural-stratigraphic horizon. 40Ar/39Ar dates of 37.57+ 0.34 Ma (basalt dike) and 162 Ma (lamprophyre dike) have been obtained from dikes in the Dee pit which are locally mineralized by the same event as Storm. This paper will focus on the descriptive aspects of the Storm deposits.

Jan 1, 2001

By S. W. Cavender

The analysis of the results of metallurgical experiments is often complicated by experimental errors and uncertainty, the complexity of the system being studied, and the confusion of correlation with causation. Consequently, comparative statistics are used to determine if a difference exists between the outcomes of tests, an estimate of this difference, and the precision of the estimate. This paper reviews the use of significance tests and confidence intervals for the comparison of results from two tests, the use of reference distributions, and blocking and randomization techniques to reduce unavoidable sources of variability. These techniques are demonstrated using plant and laboratory data.

Jan 1, 1993

By A. M. Tonnos

Underground mining has yet to see an industry wide solution for control of their ventilation systems due to the complexity and sensitivity of the underground environment. Complexity arises from multi-level, multi-zone operations and sensitivity is associated with the impact that changes in equipment status and output have on air flows and quality throughout the mine. Our approach to solving this challenge incorporates system modeling and industrial control systems in a unified architecture. Although this approach can be applied to other processes and industries, this paper will cover the theoretical and practical aspects of an integrated model-control system (MCS) as it applies to underground mining ventilation.

Jan 1, 2009

By S. Möllerherm, E. Drüppel

"The development of indicators to assess the sustainability of mineral raw materials operations is amajor task with respect to its actuality and difficulty. This holds true even more when dealing withenvironmental indicators.The use of existing environmental indicators in the mineral raw materials industry leads to false orat least distorted results. Therefore the Institute of Mining Engineering I from the RWTH AachenUniversity developed indicators and an assessment system for the mineral raw materials industryon operation, company and sector level on behalf of the Federal Ministry of Economics and Labour(Bundesministerium für Wirtschaft und Arbeit, BMWA) and the Federal Institute for Geosciencesand Natural Resources (Bundesanstalt für Geowissenschaften und Rohstoffe, BGR).In total 30 indicators were defined and designed to assess the performance of the mineral rawmaterials industry in terms of sustainable development, 10 indicators for each pillar (economical,ecological and social pillar).The following paper describes some of the results focussing on the development of environmentalindicators. These had to be adapted or completely new designed in order to match the specificcharacteristics of the mineral raw materials industry."

Jan 1, 2005

By William H. Lehr

A 4200 ton-per- hour marine transfer terminal, where river and oceangoing vessels simultaneously exchange cargos of coal and phosphate rock, is now in operation near the mouth of the Mississippi. Its materials handling machinery includes a bucket ladder barge unloader; a rope operated clamshell bucket unloader; a coal loader; and a rail mounted bucket wheel machine. The design and operation of this equipment is described as are the docks and conveying, breasting and barge-haul systems in use at the facility. Design considerations imposed by soil and river conditions, geography, operating needs and investment requirements are discussed. The economic significance of design and shipping innovations introduced by this facility is noted.

Jan 1, 1967

In practice, frothers are selected following general guidenlies and verification by laboratory and/or plant flotation tests. The terms “powerful” or “selective,” which are commonly used to characetrize frothers, have intuitive rather than scientific meaning. A research program has been set out to study fundamental properties of the flotation frothers and to identify the tests which can provide information needed to characterize and classify such flotation agents.

Jan 1, 2004

By S. C. A. Franca, M. T. Millqvist, A. B. Luz

Laboratory experiments were performed on a Brazilian diatomite from Bahia State to produce an industrial product for use as a filter aid. Bench and pilot plant tests were conducted consisting of: diatomite desegregation, organic matter and clay removal, filtration, drying and calcination. Calcination temperature and sodium carbonate addition influenced diatomite particle size distribution. Optimum filtration rates for calcined products were obtained at 900°C and 47 min. residence time with 3% (w/w) of sodium carbonate addition, and resultant products met specifications imposed on filter aids.

Jan 1, 2002

By M. N. Chandraprabha

This paper discusses the role of mineral-adapted acidiphilic microorganism Acidithiobacillus ferrooxidans on the beneficiation of arsenopyrite containing multisulfides (pyrite and chalcopyrite). Adaptation to minerals altered the surface properties of the microorganism. Bacterial adaptation to arsenopyrite and controlled bacterial adhesion to mineral surfaces lead to selectivity in arsenopyrite separation. Bioremoval of arsenic ions (both arsenite and arsenate ions) by Acidithiobacillus ferrooxidans is also discussed.

Jan 1, 2009

By W. R. Reed, Y. Zheng

A recent study conducted by the National Institute for Occupational Safety and Health (NIOSH) evaluated the roof bolter canopy air curtain (CAC) systemin a blowing face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. This study evaluates the roof bolter machine CAC while operating in an exhausting face ventilation system. This study considers two similar locations to allow comparison with the previous blowing face ventilation (Zheng et al., Min Metal Explor 36(6):1115–1126, (2019)) study: (1) a roof bolter machine bolting the roof at 20 ft (6.1 m) from the face and (2) a roof bolting machine bolting at 4 ft (1.2 m) from the face. The environment introduces 6.0 mg/m3 of respirable dust to represent the roof boltingmachine operating downstreamof the continuous miner. However, the exhausting face ventilation uses an exhaust curtain with 9000 cfm (4.25 m3/s) of air. Two roof bolter machine working positions are simulated with the use of dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8%. When the roof bolter machine operated close to the face, increasing CAC airflow was required for adequate protection since the dust reductions can be as low as 39.5%. Additional CAC airflows of 350 cfm(0.17 m3/s) and 450 cfm(0.21 m3/s) were evaluated and demonstrated that dust reductions increased to 59.7% (350 cfm) and 72.0% (450 cfm) for the worst location where the roof bolter operators located.

Aug 26, 2020

By R. Dillinger

In the environmentally conscious social atmosphere today, reclamation in surface mines has become a main issue to the public and the regulatory committees. In response to this increased attention, many regulatory committees have begun to enact more stringent regulations on surface mining operations. Operations across all spectrums of the industry have seen changes. Recently and most visibly the mountain top removal mines have seen several new regulations focusing on environmental protection. Specifically regulatory committees have emphasized a focus on the methods of reclamation and recovery of layers suitable for vegetation. These layers are the most visible once the operation has concluded. Also, these layers have the most human interaction (farming, hunting, and house development). Often times the new regulations enacted are shifting from a performance base to a standards base. The key differentiator being a performance base dictates the final result while a standards base dictates the method to achieve the result. The very nature of many regulations (especially those that are standards based) not only challenges the physical limitations of the equipment used today, they come with a financial impact. For the purpose of this paper, the model will be a surface coal operation, utilizing draglines as primary overburden movers. The coal seam is ten feet thick, the overburden ninety five feet thick, the pits are 150 feet wide, and the dragline is a Bucyrus Erie 1570.

Jan 1, 2011

By John F. Gamble

Amphiboles are hydrated mineral silicates five of which occur in asbestiform habits as asbestos grunerite (amosite) asbestos, riebeckite (crocidolite) asbestos, anthophyllite asbestos, tremolite asbestos and actinolite asbestos] and non-asbestiform habits (grunerite, riebeckite, anthophyllite, tremolite and actinolite). The asbestiform varieties are characterized by long, thin fibers while non-asbestiform varieties such as cleavage fragments form short fibers with larger widths. The U.S. regulatory method for counting asbestos fibers (aspect ratio [>]3:1, length [>]5 µm) does not distinguish between asbestos and cleavage fragments. The method biases toward increased counts of non-asbestiform cleavage fragments compared to long, thin asbestos fibers. One consequence of this regulatory approach is that workers can be erroneously classified as exposed to concentrations of asbestos (asbestiform amphiboles) above the U.S. 0.1 f/mL exposure standard when in fact they are not exposed to asbestos at all but non-asbestiform amphibole cleavage fragments. Another consequence is that the known carcinogenic effects of asbestos may be falsely attributed to non-asbestiform amphibole cleavage fragments of the same mineral. The purpose of this review is to assess whether amphibole cleavage fragments pose the same risk of lung cancer and mesothelioma characteristic of amphibole asbestos fibers. We identified three groups of workers exposed to non-asbestiform amphiboles: two groups exposed to grunerite (Homestake gold miners and taconite miners) and one group exposed to industrial talc containing non-asbestiform tremolite and anthophyllite in St. Lawrence County, NY. In addition to assessing strength of association and exposure?response trends in the non-asbestiform amphibole cohorts, comparisons were also made with cohorts exposed to the asbestiform counterpart (positive control) and cohorts exposed to the mineral (e.g. talc) that does not contain amphiboles (negative controls). The cohorts exposed to non-asbestiform amphiboles had no excesses of lung cancer or mesothelioma. Similar results were observed in the negative control groups, in stark contrast to the excess risks of asbestos-related disease found in the asbestos cohorts. The only possible exception is the twofold increased risk of lung cancer where exposure was to industrial talc containing cleavage fragments of tremolite and anthophyllite. However, this risk is not considered attributable to the talc or amphibole cleavage fragments for several reasons. A similar increased risk of lung cancer was found in Vermont talc workers, studied in the same time period. Their exposure was to relatively pure talc. There was no relationship between lung cancer mortality and exposure measured as mg/m3 years and years worked. A case?control study reported that all the lung cancer cases were smokers (or former smokers) and attributed the excess to smoking. There were two mesothelioma cases among the NY State talc workers exposed to cleavage fragments of tremolite and anthophyllite, but talc is not a plausible cause because of too short latency and potential for previous asbestos exposure. The positive controls of tremolite asbestos and anthophyllite asbestos exposed workers showed excess risks of both lung cancer and mesothelioma and positive exposure? response trends. St. Lawrence, NY talc does not produce mesotheliomas in animals while amphibole asbestos does. In sum, the weight of evidence fully supports a conclusion that non-asbestiform amphiboles do not increase the risk of lung cancer or mesothelioma. ©2008 Published by Elsevier Inc. Keywords: Amphiboles; Cleavage fragments; Lung cancer; Mesothelioma; Asbestos; Non-asbestiform amphiboles; Grunerite; Talc

Jan 1, 2007

By T. McKeon, G. Luttrell

Spiral separators are commonly used to upgrade sand-sized particles in both the coal and mineral processing industries. Many plants utilize multiple stages of cleaning and/or scavenging spirals to improve recovery and/or final product grade. Field studies suggest, however, that the layout of industrial spiral circuits is often less than optimal. This oversight can usually be attributed to a failure by plant designers to consider fundamental process engineering rules that govern the layout of complex separation circuits. This article reviews some of these important rules as specifically applied to multistage spiral circuit design. Two industrial case studies, one involving the upgrading of heavy mineral sands and a second involving the cleaning of fine coal, are presented to illustrate the impact of good design protocols on spiral circuit performance.

Jan 1, 2007

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models. INTRODUCTION There are many definitions of virtual reality (VR) that include various levels of immersion and features [1]. Some definitions refer to specific technologies [2], while others are limited to visualization [3]. For this paper, a more general definition of VR will be adopted. VR is defined as the collection of hardware and software that interactively engages users and stimulates their senses within a synthetic or virtual environment. From a hardware standpoint, this can include anything from a phone to a head-mounted display (HMD) to a large-scale theater as well as speakers, microphones, haptic sensors, and interaction devices. The software used to create virtual environments (VEs) generally includes a game engine, custom software components and libraries, and two-dimensional and three-dimensional graphical assets. Recent hardware and software advances have increased the fidelity and availability of VR. New and improved technologies including HMDs and high-resolution monitors and projectors can display sharper, more detailed visualizations. For example, in the past five years between the release of the Oculus Rift DK1 (2013) and the HTC Vive Pro (2018), there was a three-fold increase in resolution along with a 50% increase in the refresh rate. Furthermore, despite early claims that low-cost VR technology was readily available [4], computational power has not been sufficient to handle the large amount of data generated by these systems [5]. In the past five years, however, rendering speeds have more than doubled and memory has more than tripled [6], allowing these visualizations to be incorporated into higher-complexity and -fidelity VEs that more closely mirror the real world. Similarly, software capabilities have also significantly improved through game engine advancements and feature development. In the past several years, game engines have added and improved features such as physics, lighting, platform support (e.g. Android), and asset development integration. Some of the current leading commercial game engines are Amazon Lumberyard, CryEngine, Unreal, and Unity, but this can quickly change as is evident in the literature [7, 8].

Jan 1, 2019

By D. R. Wilburn

his summary of international mineral exploration activities for the year 2011 draws upon available information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents [ ] analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia; 2) regional and site-specific exploration activities that took place in 2011 as compiled by the USGS and 3) regional events including economic, social and political conditions that affected exploration activities, which were derived from published sources and unpublished discussions with USGS and industry specialists.

Jan 1, 2012

By Steven K. Duke, Jay Arabshahi

An economic, real-time probe drill monitoring system was developed for Metropolitan Water District’s Arrowhead Tunnels project to quantitatively evaluate ground conditions ahead of a TBM. This system digitally records hydraulic feed, rotation, and percussion pressures and calculates drill advance rates during drilling. These data are computer synthesized to develop a digital representation of the ground ahead, and the resulting “picture” of the ground is distributed to the project team to assist with tunnel construction decisions (i.e., targeting grout holes, optimizing mine-cycle lengths, and avoiding becoming stuck). The analysis and interpretation procedure has now been calibrated and refined using over 5,000 m (3 miles) of geologic face mapping data.

Jan 1, 2007

By K. L. Lownie

For research and test data to serve a useful purpose, it is essential that it be derived from some known standard test procedure that allows for comparative analysis as well as independent replication and verification. Fan performance data provided by manufacturers is not absolute, and is influenced by the geometry of the test installation. For these reasons, fan test standards have been prepared in order to establish a clearly defined test procedure that allows for comparison of different fan designs, and also allows for the independent verification of test data. Internationally recognized Standards such as BS848, ISO5801, and AMCA 210 etc. are highly prescriptive, and precisely specify test duct configurations, measurement procedures, measurement planes and instrumentation to be used. Provided the laboratory tests are conducted strictly in accordance with the relevant Standard, the performance data will accurately reflect fan performance within the appropriate tolerances for efficiency, pressure and flow when tested in the defined configuration. Major differences in performance exist between a fan tested in accordance with a Fan Test Standard, and an identical fan installed in a mine ventilation system. The aerodynamic performance of any fan will be influenced by the quality of the fan manufacture, the flow system within which it is operating, the location of measurement planes, and the system stability. The flow distributions present in a standardized Laboratory test are unlikely to be repeated in mine ventilation systems, and this will also disadvantage fan performance. Unless the fan supplier takes all of these influences into account, there will an inevitable reduction in fan aerodynamic performance, and the end user will experience a shortfall in expected flow through the mine. The effect on fan performance can range from minor inconvenience to catastrophic fan failure resulting in major rectification costs and significant loss of mine production.

Jan 1, 2009

By Charles H. Minott, Michael J. Markow, Robert D. Wyatt, Fred Moavenzadeh

The substantial investment in tunnels anticipated in the next twenty years has focused new attention on the economics of tunnel construction itself and on some costly problems associated with underground work: the uncertain geologic conditions, the performance and adaptability of men and equipment, and the need for quicker, more efficient excavation methods. There also exists a need to develop better ways of estimating tunnel construction. Inaccuracies in current bid estimates stem from a number of causes, among them (1) the effects of geologic conditions, which are not adequately known prior to construction, (2) the dependence of actual cost on the construction method used and on the interactions among the operations occurring underground, and (3) the reliability of tunneling equipment. Inability to estimate final costs for conventional tunneling more accurately has in turn caused difficulty in gauging the costs and benefits attributable to new tunneling technologies either under development or for which R&D programs are planned. ATTRIBUTES OF THE TUNNEL COST MODEL This paper presents a computer based Tunnel Cost Model (TCM) which quantitatively assesses the uncertainties inherent in underground work, and is detailed enough to aid in preparing estimates or bids. The model employs appropriate techniques of subjective (or "degree of belief") probability and computer simulation of tunnel construction operations to estimate distributions of total tunnel

Jan 1, 1974