Search Documents

By G. Hwang, S. Park, H. Kim, J. Choi, P. Seo

"In the mineral processing, clay minerals have negative effects on the flotation of valuable minerals. In this study, we investigated how the floatability of malachite (CuCO3·Cu(OH)2) is affected by presence of the clay minerals in the fundamental aspects. Flotation experiments were conducted by using Na2S and PAX (potassium amyl xanthate), and the floatability of malachite was compared between the cases in the presence and absence of clay minerals. The results showed that floatability was greater in the absence of clay minerals than in the presence of clay minerals and decreased with increasing weight percent of kaolinite under same conditions applied. In addition to examine how clay minerals affect malachite floatability, we conducted flotation experiment with changing clay adding order. The results indeed showed that malachite floatability was affected by clay adding sequence. INTRODUCTION The demand of copper is growing as industrial development increases, but mineral resources are limited. Therefore, studies for Cu oxide flotation are being conducted to improve their recovery(1-3). However the mining industry is well aware of the difficulty in treating copper ores in the presence of clay minerals(4). Clay minerals have unique properties and these properties may affect flotation. In the previous studies, the effect of slime coating of clay minerals on flotation was investigated(4-6). For example, Zhao and Peng (2014), Peng and Zhao (2015), and Arnold and Aplan (1986) found that clay slime coating on chalcopyrite, chalcocite and coal surfaces through the electrostatic attraction reduced surface hydrophobicity and then depressed the flotation. Other researchers have also reported clay minerals have impact on pulp rheology. Especially in the case of bentonite, pulp viscosity increased with increasing amount of bentonite and the higher pulp viscosity have deleterious effect on copper recovery(7, 8). However, these studies only focus on slime coatings and pulp rheological behavior. Forbes et al. attempted to decoupling rheology and slime coatings effect on flotation but this study has limitation that individual role of two clay species either attached to mineral or suspended in bulk solution was excluded(9). Hence, in this study, we aimed to investigating the effects of individual clay (suspended and attached) on malachite flotation."

Jan 1, 2016

By R. Bhaskar, H. Xie

Fractal theory was horn in the mid-1970s. Since then, its application has been spreading day by day, from mathematics and geology to areas such as geophysics, physics and material sciences. In this paper, fractal models are developed to characterize particle size distribution and surface area. Theoretical formulas are derived for the computation of fractal dimensions D (size) and D[s] (surface area). The models developed are applied using experimental data of particle size distribution and surface area obtained from the Microtrac Particle Size Analyzer for dust processed by several size reduction devices. The theoretical models and the experimental data are found in good agreement. The fractal dimensions obtained are D = 1.350 to 1.770 and D[s] = 2.058 to 2.584 for fine coal dust particles (< 15 µm) produced by various size reduction mechanisms. The physical meaning of these fractal dimensions is also related to the dust generation processes.

Jan 1, 1994

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, Aditya Rana, M. M. Singh

The paper presents an innovative directional controlled blasting (DCB) technique for excavating unstable slopes along the Konkan railway in India without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw were developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3, irrespective of the actual free face, was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle was changed from 80–82 to 45–47 degrees, and possible wedge, planar and toppling failures were eliminated. No incident of rockfall and slope failure along these slopes has been observed after the stabilization.

By M. S. Klima

This paper will detail the work that has been done in 1990 and 1991 at the Pittsburgh Energy Technology Center (PETC) on the development of the U.S. Department of Energy&apos;s (DOE) patented Micro-Mag Process. This process entails the use of a micronized-magnetite (minus-10 microns) and water mixture for cleaning fine coal (minus-600 microns) in a cyclone, along with the production and recovery of the magnetite. Emphasis will be on the results from micronized-magnetite recovery testing using both conventional wet-drum and high-gradient magnetic separators in which several key operating conditions were varied including feed percent solids, magnetite-to-coal ratio, magnetite grade, and feed rate. Also presented will be selected results from testing done on a 76-mm diameter cyclone at a relative density of 1.50 showing the effects of operating pressure, magnetite grade, and medium-to-coal ratio on separation efficiency. In addition, two methods for producing micronized magnetite, along with the corresponding size distributions, will also be discussed.

Jan 1, 1992

By C. A. Pickles, S. J. Splinter

Silicon oxynitride, Si2N20, has many of the intrinsic properties of a potential high temperature engineering ceramic material. Some of these properties are similar to those of silicon nitride, which has been more intensively studied. However, although silicon nitride ceramics are approaching a state of microstructural refinement for various engineering applications, silicon oxynitride has received little attention. This has been mainly due to a lack of an economical and reproducible method of producing pure crystalline Si2N2O. Several reports exist on the preparation of crystalline Si2N2O from SiO2 and Si3N4, yet very little kinetic data exist. Even less is known about the carbothermic reduction of SiO2 in a nitrogen atmosphere to produce Si2N2O. In this paper, a review of the properties and methods of preparing silicon oxynitride will be presented. In addition, results obtained by reactively sintering SiO2 and Si3N4 will be discussed. The overall reaction is as follows:

Jan 1, 1990

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

9.1 INTRODUCTION There are approximately 70,000 abandoned coal mines nation¬wide, which is about 35 times the number of underground coal mines presently operating. The US Bureau of Mines estimates that there are over 8 million acres of undermined land due to the extraction of coal, metals, and nonmetals. Subsidence has affected more than 2 million acres, and more than 99% of the subsidence is related to underground coal mining. There is reason to believe that some of the remaining 6 million acres of the undermined land have a high potential to subside. The expansion of housing, highways, commercial structures, and other facilities has required the use of many areas that are underlain by abandoned coal mines, and this growth will continue. Many subsidence problems are derived from the collapse of aban¬doned underground coal mines. There are numerous abandoned mine workings in the anthracite fields of northeastern Pennsylva¬nia, in the Appalachian bituminous fields, the Illinois Basin, the Rock Springs, Wyoming area, and other areas of the United States (Gray et al., 1976). Various room and pillar patterns of mining have been used in the dipping anthracite seams and the nearly flat-lying bituminous seams with considerable variation in the per¬centage of coal extracted. The progressive deterioration of pillars, mine floors, and mine roofs after long exposure to air and water may later result in the collapse of strata over the mine entries, the crushing of the remaining coal pillars, or the bearing failure of the mine floor beneath the coal pillars. Subsidence then results as the collapse reaches the ground surface in the form of differential strains, depressions, cracking of the ground, and sinkhole devel¬opment. Subsidence over active longwall mines, which occurs concurrently with mining or is completed within a short period following coal extraction, has been studied extensively over the past decade. On the other hand, subsidence over abandoned coal mines receives little attention by the researchers, mainly because it is difficult to predict and takes place decades after mining has ceased. The techniques of investigating the subsidence events over abandoned coal mines are similar to those employed for active mines except that at the outset, it is necessary to determine whether or not the subsidence events are mining-related (Chugh et al., 1986; Cummings and Singh, 1986; Peng and Hsiung, 1986). This calls for the identification and confirmation of abandoned mine workings under or near the affected surface structures. Gen¬erally old mine maps, if available, are acquired, the surface bore¬holes are drilled for confirmation of the accuracy of the mine maps and determination of the potential for continued subsidence. Sub¬sidence monuments are established and periodic surveys con¬ducted to determine the amount and trends of surface movement in and around the affected surface structures; surface boreholes are used to investigate the integrity of the underground structures (i.e., roof, coal pillars, and floor) by TV camera. They are also used for monitoring the vertical and horizontal movements of the subsur¬face strata by Sondex (FPBX) and inclinometer (PFBI), respec¬tively, for determining the continuity of the subsidence events. Tape extensometers, crackmeters, etc., are used to monitor the development trends of major cracks in the structures or on the ground. These data are used to identify the causes of the subsidence events. Finally, abatement methods are selected to stabilize the structures. It must be noted that most subsidence events over abandoned coal mines are reported after the fact, and investiga¬tions are begun some time after reporting, that the subsequent measured movements are generally much smaller than that at¬tained in the active mines, and that due to lack of knowledge about the damage conditions and the exact location of the abandoned mine workings with respect to the affected surface structures, the precise causes of surface subsidence or surface structural damages are in most cases very difficult to identify. 9.2 TYPES OF SURFACE SUBSIDENCE According to Gray et al. (1977), after examining 354 incidents of subsidence above abandoned mines in the Pittsburgh metropol¬itan area, the subsidence features have a mean diameter (i.e. the average of long and short dimensions) from less than 1 ft to 1600 ft, with 84% less than or equal to 15 ft; the subsidence features have a depth ranging from less than 1 ft to 48 ft, with 89% less than 25 ft; 66% of the subsidence features are deeper than they are broad. Nearly 59% of the subsidence features occur with overbur¬den less than 50 ft thick and 81% less than 100 ft thick. No subsidence features occur with overburden thicker than 450 ft (Fig. 9.1). Occurrence of subsidence incidents varies from imme¬diately to more than 100 years after mining (Fig. 9.2). In analyzing the characteristics of approximately 3000 chim¬ney subsidence features along the Colorado Front Range, Matheson and Eckert-Clift (1986) examined historical aerial photographs on 4- to 14-year intervals between 1937 and 1967 and found that the majority of observable surface subsidence features occurred within 30 to 40 years after mining. According to Gray et al. (1977), the most prevalent subsi¬dence features over abandoned mined land are sinkholes, with depths of more than 3 ft, and troughs or sags, usually less than 3 ft deep. Sinkholes are steep-sided pits, while troughs are shallow depressions much wider in area than sinkholes. A. SINKHOLE SUBSIDENCE A sinkhole is caused by the collapse of a mine roof that works its way upward. If it is not arrested during the process it will eventually reach the surface and emerge as a sinkhole. The process is governed by the thickness and character of the overburden, the width and height of the mine openings. Sinkholes are usually 3 to 20 ft deep and may be 2 to 40 ft in diameter, although most are fewer than 16 ft across (Gray et al., 1977; DuMontelle and Bauer, 1983). Newly formed sinkholes have steep sides with straight or bell-shaped walls. At times, they appear to be conical in profile with the apex upward. If the topsoil collapses, the top portion will widen to form an hour-glass shape. Sinkhole subsidence usually occurs over abandoned mines less than 165 ft deep (Hunt, 1979). Matheson and Eckert-Clift (1986) found that chimney sink¬holes are likely to occur when the ratio of overburden thickness to mining height (h/m) is less than 4 to 5. When h/m is between 5 and 10 to 11, the potential occurrence of chimney sinkholes decreases rapidly. When h/m is more than 10 to 11, less than 10% of the mine openings that collapse will induce sinkholes on the surface.

Jan 1, 1992

By L. A. Rapoport

This paper outlines the methodology and results pertaining to the simulation of the U.S. coal industry in the context of an integrated, time-dynamic model of Long-Range Energy Developments and Supplies (LORENDAS). By way of background we will present first an overview of the overall LORENDAS model structure. We will, then, outline the characteristics of the formulation and data used for the representation of the U.S. coal industry. Finally, a series of model results will be reviewed, with particular emphasis on the long term projections of coal production and distribution under different basic economic and/or political scenarios.

Jan 1, 1977

By J. A. Bradbury

N. A. Degerstrom, Inc. has constructed and operated a processing plant approximately five miles north of Soda Springs, Idaho for processing a byproduct phosphate treater dust from Monsanto&apos;s elemental phosphorus plant, also located in Soda Springs. The plant is designed to produce agricultural-grade phosphoric acid, gallium, and silver. The design capacity of the plant is 54.4t (60 st) of treater dust per day, which can produce 16,326t (18,000 st) of phosphoric acid, 6,600 kg of gallium, and 6,033 kg (194,000 oz.) of silver per year.

Jan 1, 1993

By John Kuyt, Zili Li, Michael Mooney, Michele Mangione

"INTRODUCTIONTwin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world. A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a betterunderstanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This paper discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link Project OverviewThe Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with over 7km of twin-bore road tunnels, two lanes each, with several caverns, interchanges, and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a Public-Private Partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5m double-shield Herrenknecht TBMs [1]. The TBMs were used in EPB-type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1 m diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in a 9 segments + 1 key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis [2]. Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Jan 1, 2016

By William Gleason

"In 2008, the world quietly hit a milestone that did not receive much fanfare or publicity, but it hit one that marked a turning point in the history of mankind and the way the planet is and will be inhabited in the future. It was in 2008 that, for the first time, more than half of the world’s population, an estimated 3.3 billion people, resided in urban areas. The world’s population had moved from being a majority of agricultural and rural society to an urban society. Andrew Whalley, deputy chairman for Grimshaw Architects, said this change in where and how people live will continue to increase urban populations and, by 2050, it is estimated that more than 6.4 billion people will live in urban areas. To meet these needs, Whalley, speaking during the keynote session of the 2105 Cutting Edge conference in Denver, CO, said future cities will have to be reimagined and redesigned to be more efficient. A large part of that design will be in the infrastructure of those cities.At the Fourth Annual Cutting Edge Conference, Sept. 21-23, much of the discussion was around how the tunneling and underground construction industries improve cities in a number of ways, including societal, environmental and in overall efficiency. There was talk, not just about the improvements that society enjoys at the completion of such projects, but also about the challenges faced by the owner and contractor in the construction of such projects.The conference, titled Urban Tunneling, brought together some of the top minds in the industry to not only discuss the issues faced today, but also those that will shape the industry in the future.For his part, Whalley spoke about a number of projects around the world and how they have impacted society in ways beyond simply providing a better means for transportation of people or water. Notably, he spoke about the Crossrails project in London.London is a city of 8.6 million people and a history that dates back nearly 2,000 years. It is a great example of the challenges the industry faces in bringing modern efficiencies to an established city.Running more than 100 km (62 miles) with more than 42 km (26 miles) of tunnels passing through 40 stations, including 10 new stations, the project is the largest in Europe and will transform the way people move about the city."

Jan 1, 2015

By Paul C. Miclea

In case of a major fire in a tunnel between stations or ventilation shafts, if the buoyancy effect of the hot gasses is stronger than the airflow induced by the fans, the risk of backlayering could restrict the safe evacuation of people. Obstructions in the tunnel and alternate airflow paths can further reduce the air velocities past the fire. Currently there are two computer programs available to address the issue of underground fires: o "Subway Environment Simulation" (SES), Version 3.0, developed by Associated Engineers, a Joint Venture of Parsons Brinckerhoff Quade & Douglas, Inc., De Leuw Cather & Co., and Kaiser Engineers, Inc. for the U.S. Department of Transportation o "MFIRE", Version 1.26, developed at Michigan Technological University for the U.S. Department of the Interior, Bureau of Mines. As implied by its name, the SES program was developed specifically for the analysis of subway ventilation systems. It can be used to analyze the heat released into, and removed from, a subway or vehicular tunnel and to determine the effect of ventilation elements on airflows throughout the network of stations or other merging tunnels. It has a special feature allowing the user to predict the effects of a fire at any location within the subway system. Version 3.0 of the SES program is designed to be used with a "critical velocity" calculation in order to determine whether or not tunnel airflows can be controlled during a train fire emergency. The original version of the program was written in FORTRAN for mainframe computers, such as the IBM 4381. Recently ICF Kaiser Engineers has compiled a version of the SES program for PC use. The MFIRE program simulates the interdependence between a mine ventilation system, with its pertinent fans and structures, and changes in ambient conditions or a source of heat, such as a fire. It also accounts for natural ventilation. The program is written in FORTRAN 77 and compiled for 8086/8088 based microprocessors, allowing it to be run on an IBM PC or compatible computer with a 2.0 or a later version of DOS, 256K random access memory (RAM), and a text editor. This paper reports the comparative results of an application of both programs for the same network in a recent study.

Jan 1, 1991

Coal waste materials inhibit direct vegetation establishment due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss # I coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980&apos;s with little topsoil resource available for final closure. The refuse was acidic (Total-S = .. 38%; pH = 3.6), black, high (70%) in coarse fragments, and had a low water holding capacity (4.5% in < 2.0 mm fraction). A small plot experiment was established on the refuse pile to evaluate the influence of liming rates (50% and 100% of lime req.) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from < 4.0 to > 6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Application of 27 Mg ha-1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity in leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile, so long term water treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 1999

By Circe Verba, Scott Montross, Jon Yang

This work is a first-order study to assess the suitability of an organic acid lixiviant to extract rare earth elements (REE) from coal preparation fines refuse sourced from a Pennsylvania mine with a total REE of ~ 300 ppm. The extraction of REE using an organic acid, in this case 0.1Mcitric acid and 0.5Mtrisodium citrate solution, is compared against 0.5M(NH4)2SO4, 1MHCl, 1.2MH2SO4, and 0.5Methylenediaminetetraacetic acid (EDTA). Ashing the coal waste material prior to leaching tests with the citrate solution nominally improved REE extraction. Buffered citrate solution recovered 7% of the total REE in the as-received Isabella Fines as compared to 11% in ashed samples, whereas (NH4)2SO4 extracted 5–6%, respectively. EDTA recovered up to 33%of the total REE, most likely due to the higher coordination chelate bond. Mineral acids, however, outperformed the organic acids on ashed material (16–52%REE recovery), suggesting that organic acids may not be a suitable competitive option for REE extraction from these types of feedstocks.

Jun 15, 2021

By T. M. Gurr

Large quantities of phosphate rock are mined and processed in Central Florida (Figure 1). The phosphate rock from the mines is further processed in "chemical plants" to produce phosphoric acid (Figure 2). A by-product of the processing&apos; of the phosphate rock to produce fertilizer chemicals is an impure form of gypsum referred to as phosphogypsum. For each ton of phosphate rock processed, approximately 1.5 tons of phosphogypsum is produced (Figure 3). The typical method to dispose of this by-product gypsum is to stack it in large piles, locally referred to as gypsum stacks or gypsum fields (Figure 4). These gypsum stacks have been the focus of many studies in recent years in an attempt to identify the potential for ground water and/or air pollution associated with the stacks. This paper attempts to discuss some of the ground water impacts and current attempts to minimize these impacts.

Jan 1, 1990

By Joao B. Cardoso

This paper describes a two-stage reverse flotation method developed at the Mineral Resources Institute (MRII, University of Alabama, for Kerr-McGee Corporation (KMC), to separate the trona (Na2CO3 ? NaHCO3 ? 2H2O) from a saline deposit containing halite, borax, minor salts, and water insoluble materials. In the first stage, trona is depressed with Quebracho, and the insoluble gangue is floated with fatty acid. In the second stage, trona is floated with cresylic acid. The flotation concentrates contained better than 90% trona with insolubles ranging between 1 and 2%. Although the trona recoveries were low, optimization and middlings recycled in a continuous circuit could substantially increase the value.

Jan 1, 1989

By B. Stewart, R. Li

Coal waste materials inhibit the direct establishment of vegetation due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss #1 coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980s with little topsoil resources available for final closure. The refuse was acidic (Total S = 0.38%; pH = 3.6), black in color and high (70%) in coarse fragments. The refuse also had a low water-holding capacity (4.5% in < 2.0-mm fraction). A small plot experiment was established on the refuse pile to evaluate the effects of liming rates (50% and 100% of lime requirements) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from <4.0 to >6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only. This was due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Applica¬tion of 27Mg ha`1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and this appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity of leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile. Therefore, long-term water-treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 2000

By A. M. Marabini, G. Belardi, V. Alesse, M. Acosta

Sotiel mine is situated in the Iberian Pyrite Belt in southern Spain, some 40 km north of the port of Huelva. Although mining operations at the site date back to Roman times, the present mine came into production in 1983 and 5.6 million tonnes of ore had been extracted by 1993. The orebody is volcano-sedimentary and consists of fine grained copper, lead and zinc minerals in massive pyrite surrounded by slates and volcanics. Prior laboratory research had resulted in the synthesis of a new collector, belonging to the MercaptoBenzoOxazole (MBO) class that acts selectively towards Cu and Zn minerals after activation with CuS04. The MethylMercaptoBenzoOxazole (MMBO) version of this collector had been used for the laboratory flotation of Cu minerals and sphalerite activated by CuS04. This resulted in identification of the optimal physicochemical conditions for laboratory-cell flotation of the two minerals from samples of complex sulphide ores, and subsequently the reagent has been tested in the Sotiel plant (Spain). The plant has three flotation sections. With conventional re-agents, the first section yields a Cu concentrate grading 21% with a total recovery of 29%, and the second one yields a 40% Pb concentrate with total recovery of 34% and a 47% Zn concentrate with total recovery of 78%. Application of the new synthetic reagent in the copper and zinc circuits produces a more selective process with a decrease in re- agent concentration grade and recovery are increased by 2 and 9 points respectively in the case of Cu and by 1 and 3 points where Zn is concerned. Moreover, the penalty elements in the Cu concentrate are halved.

Jan 1, 1995

By K. L. Gabby

Selective removal of mercury from cyanide leaching solutions while retaining silver has been a long-standing problem, due to the chemical similarity of mercury and silver. In order to be practical, a mercury removal process needs to be both highly selective and use inexpensive materials. This paper reports the use of zinc sulfide (ZnS) as a precipitant for mercury. The mercury cyanide complex (Hg(CN)4 2-) undergoes a replacement reaction with the zinc sulfide, forming insoluble HgS, while the silver cyanide complex (Ag(CN)2 -) remains in solution. Under appropriate conditions, the separation of mercury from silver is nearly quantitative, with close to 100% removal of mercury, while nearly none of the silver is precipitated.

By KAGAN BENZESIK, OMUR CAN ODABAS, SELCUK KAN, Onuralp Yucel

In this study, domestic molybdenum disulfide (MoS2) concentrate was roasted in a chamber furnace and then in a rotary kiln. The behavior of the roasting process was examined in both furnaces, and which type of furnace is more advantageous to use in mass production was investigated. It is theoretically possible to roast in a chamber furnace, but a major problem was observed when the amount of concentrate was increased in the chamber-furnace experiments. The problem was solved by using a rotary kiln. This study improves the understanding of the roasting of  MoS2 concentrate and presents a different perspective to the industry, showing that rotary kilns can also be used for roasting.

By Otis M. Clarke

The Eufaula bauxite-kaolin district in southeastern Alabama is an important source of raw material for the refractory industries in the United States. At the present time, five companies are mining and processing bauxite and kaolin from this district and a sixth company is holding substantial reserves. Mining operations are expanding, but finding new ore reserves is a major problem. The Geological Survey of Alabama sponsored geologic research in the Eufaula district to: 1) investigate the utilization of sandy kaolinS and other clays associated with bauxite-kaolin deposits; 2) find limits of the bauxite district, looking for possible extensions; and 3) study the geology of the district, looking for patterns or trends that may aid in finding new ore reserves. This work was done with the full cooperation of mining companies operating in the district and property owners. Research was aided by the U.S. Bureau of Mines and the University of Alabama. The investigation included detailed geologic mapping of mines, drilling in selected areas, and making mineral analyses of bauxite and clays. The mapping was performed primarily by pace and compass because of the complexity of the deposits studied, but aerial photographs were used to a limited extent. Drilling included both auger and core drilling. The auger drilling was limited to 100 feet, but core holes were drilled as deep as 200 feet. The term &apos;bauxite,&apos; as used here, indicates a mixture of minerals containing more than 50 percent gibbsite. Bauxitic clay is a mixture of gibbsite and kaolinite that contains more kaolinite than gibbsite. The term "kaolin" indicates a clay composed of predominantly kaolinite. Other clays in the Eufaula district are composed of kaolinite, illite, quartz, mica, and goethite or hematite.

Jan 1, 1971