Search Documents

By Changjiang Li, Jun Yang, Qiang Fu, Xu Chang, Xing Wu, Yubing Gao

With the development of underground mining, the deformation of roadway floor has increasingly become a major constraint on the safe and efficient production of coal mines. To address the floor deformation that was caused by massive stress concentration in roadway, an innovative method based on deep-hole directional tensile blasting technology is put forward. By taking No.122108 working face in Caojiatan Coal Mine as engineering background and analyzing the mechanism of deformation, a numerical simulation and field test are carried out to verify the effect on deformation control of this technology. It is found that the deep-hole directional tensile blasting technology can actively control the fracture position of the roof in the gob area and cut off the stress transmission path, so as to relieve the stress in the roadway. And since different blasting parameters have different impacts on the stress relief effect, a numerical simulation is implemented and it is found that the stress relief effect is the best when blasting depth is set to be 32 m and the blasting angle be 60°. By applying the optimal blasting parameters to the field engineering test, it can be seen that the deep-hole directional tensile blasting technology could effectively reduce maximum stress value and stress field range of the both sides of the roadway, and make the stress field far away from the roadway, thus effectively controlling the deformation of the roadway floor. The deep-hole directional tensile blasting technology can effectively solve the problem of roadway floor deformation and can be safely applied to engineering sites.

Jun 13, 2023

By Thomas Hard

A description is given of a new facility processing blast furnace slag into a high quality cementitious material to be used as an ingredient in concrete for general construction purposes. A brief history of the process is given, followed by a detailed discussion of the water granulation system and the methods used to transport and dewater the granulate. Environmental advantages of handling slag away from the blast furnace by water granulation are included.

Jan 1, 1983

By Kot F. Unrug

When reading different studies discussing trends in coal mining, it appears that a substantial expansion of output by the year 2000 is predicted, even in the most pessimistic forecasts. Depletion of shallow, easy-to-mine deposits is only a matter of time, and the future average mining depth will increase. The proportion of slope to shaft mines operated during the next decades will change in favor of the shaft mines. Since an increasing amount of shafts in new nine developments seems to be inevitable, it appears appropriate to focus more attention on shaft design criteria. Some valuable papers have recently been published (1) that emphasize geotechnical aspects of shaft design. In the discussion that follows some other aspects of design criteria will be evaluated.

Jan 1, 1984

By R. Bryce, T. J. Doughty, K. Stoll

Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Ca6Al2(SO4)3(OH)12•26H2O Ettringite readily precipitates in high pH water and by doing so, removes sulfate from impacted waters. The SAVMIN process, piloted in South Africa, is one method to produce ettringite. In this process, aluminum hydroxide is the aluminum source. The Cost Effective Sulfate Removal (CESR) process is similar to SAVMIN, but uses a proprietary aluminum source instead of aluminum hydroxide. Outotec and Veolia also have their own versions of the process using their specialized process equipment. TWC patented a version of ettringite precipitation using metallic aluminum as the aluminum source for ettringite formation. The benefit of using aluminum metal is that no additional ions are added to the process. At high pH, the raw aluminum corrodes in water causing hydrogen gas generation as the water is chemically reduced. This reaction is shown below:

Jan 1, 2019

By Yuting Xue, Mark Van Dyke, Zoheir Khademian

Borehole scoping has been widely used in the U.S. underground coal mines as a method for geologic mapping and stability analysis because it is very useful for identifying rock types, voids, fractures, and formation boundaries through the direct observation of the borehole wall. An image stitching technique was proposed to generate panoramic borehole images from side-view borescopes in a previous study. However, the generation of panoramic borehole images can be affected by the borehole condition because the image stitching process highly depends on the key point detection and matching. The presence of dust and water could have a significant influence on the detection of key points. In this study, the influence of borehole conditions on panoramic borehole images was studied from the success of image stitching and the visibility of geologic features and lithology changes. Borehole videos recorded at different times, when the same borehole was freshly drilled, freshly washed with water and 12 days after washing, were processed with the proposed technique. The comparison of the stitched images shows that the presence of dust has minimal influence on the image stitching process but shows significant negative effects on the visualization of geologic feature and lithology change. In addition, the presence of water can significantly hinder the image stitching process, which in turn helps in identifying lithology change. Borehole scoping aids in identifying and mitigating hazardous conditions in underground mines, and this study provides preliminary inputs into identifying optimum borehole conditions for geologic mapping with panoramic borehole images.

Feb 1, 2025

By William A. Vogely, Lawrence J. MacDonnell

This section begins with an introduction to several key environmental laws. This is followed by a discussion of some of the issues raised by such environmental regulation. Finally the subject of regulatory reform is addressed. Overview of Selected Major Environmental Laws The number, type and complexity of environmental laws and regulations affecting mineral resources development have grown at an astonishing rate since the 1960s. The most significant laws and regulations are those addressing the use of the public lands; those concerned with air quality, water quality, and surface reclamation; and those defining government responsibility for its actions having important environmental consequences. The laws and regulations governing activities on the public lands will be taken up in the section 5.15C, "Minerals and Land Management." In this section we will concentrate on five primary laws: the Clean Air Act, the Clean Water Act, the Surface Mining Control and Reclamation Act, the Endangered Species Act, and the National Environmental Policy Act. The Clean Air Act: The legislative and regulatory framework for controlling air pollution has developed in a series of steps. Most important for present purposes are the Clean Air Act of 1970 (P.L. 9 1-604) and the 1977 Amendments (P.L. 95-95). The rather complex air quality control scheme includes four key elements-national ambient air quality standards, state implementation plans, the prevention of significant deterioration program, and the non- attainment program. National Air Quality Standards. The 1970 Clean Air Act is a landmark law because it contains the first explicit recognition that pollution is a nationwide problem requiring a national control program. The federal government through the Environmental Protection Agency (EPA) was to establish national air quality standards for at least the six pollutants named in the Act (sulfur dioxide, carbon monoxide, total suspended particulates, photochemical oxidants, hydrocarbons, and nitrogen dioxide). These standards were to be established so as to protect public health, "allowing an adequate margin of safety." The cost of achieving these standards is not to be considered. The 1970 Act unrealistically required that these standards be achieved in all areas of the country by 1975. As the program has developed, the air quality control regions are now to be designated as "attainment" or "nonattainment" with respect to each of the national standards. State Implementation Plans. Under the Act the states are given the primary role in achieving the ambient standards. States are to develop and implement control plans governing emissions from all existing and new sources. These plans can include emission limitations for existing stationary sources, transportation control plans to reduce emissions from mobile sources, and pre- construction review of new stationary sources to assure compliance with new source performance standards. The EPA must approve all state implementation plans. Sanctions are given to the EPA to be applied if states fail to submit acceptable

Jan 1, 1985

By T. N. Andersen

The history of gold and silver analyses shows an interesting duality. On one hand, classical chemical and instrumental methods have evolved to meet changing needs, but on the other hand, the age-old and somewhat empirical fire assay has remained a popular tool. Inasmuch as gold and silver generally have been present in ores at low concentra¬tions, methods have been challenged by a need for sensitivity and selectivity coupled with reasonable assay time. A progressive increase in the importance of low grade materials as ore sources has led to the need for improved methods. Assays of these materials are required for process control and accounting in operating plants as well as for guiding research and development activities. The analytical response to these needs is evidenced by numerous reviews published through 1977-¬e.g., cf Kolthoff and Elving (1966), Beamish and Van Loon (1966, 1972, and 1977), Young (1971) , Mallett (1970), and Sen Gupta (1973). In this paper we present a brief sketch of the history and status of various gold and silver methods. A more detailed summary of atomic absorption spectroscopy (AAS) is Given, as this method has gained in popularity more than other assay methods. AAS methods currently in use are summarized and discussed briefly. This paper is not meant to be a detailed review, as are the above mentioned publications. Rather, we borrow from those works and more recent papers to report trends in gold and silver analyses (particularly in AAS). Also, we discuss some selected poten¬tial problems, and problems that have been experienced by this laboratory.

Jan 1, 1981

By J. D. Allen

The Concord Mine Coal Preparation Plant of United States Steel Corporation, located near Bessemer, Alabama, began operations in June, 1950. The basic cleaning circuit consisted of a Chance Cone for cleaning the 2-inch x 3/8-inch fraction and concentrating tables for cleaning the minus 3/8-inch coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable (Figure 1), 85 per cent passing three mesh and 25 per cent passing 28 mesh, there was a considerable amount of fines passing through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-foot diameter hydro-separators with the underflow returning to the dewatering screens and the overflow going to a 175-foot diameter thickener for water clarification, (Figure 2). As might be expected, there was a considerable amount of recirculation of the minus 35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20 per cent. Further reduction to approximately 11 per cent was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a smaller percentage of the coal previously used at the coke plant, the high moisture and fluctuations did not seriously hamper coking operations.

Jan 1, 1966

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006

By Jim Huerta

Diesel fuel usage in the mining industry continues to escalate. This is because approximately 60 percent of all mined materials are surface extracted by large equipment using diesel fuel, which continues to increase in cost per gallon. For example, coal mining uses large equipment such as wheel loaders, wheel dozers, draglines and [ ] dredgers. In one year, three of the largest U.S. coal mining operations consumed approximately 567 million to 852 million L (150 million to 225 million gal) of diesel. At an approximate cost average of $3.25/gal the expenditure on diesel is $487 million to $731 million per year. So, are there any solutions that could reduce this cost burden? Yes, there are. Coal mining companies can extract less ore; use more efficient extracting equipment that consumes less fuel; wait for a significant reduction in the cost of fuel; or find and use technology that would create efficiencies that would lower the cost. Nanotechnology is one such technology that might provide the means to create the efficiencies that will significantly lower diesel fuel costs.

Jan 1, 2011

By Madhu G. Ranade

A statistically designed pot grate- kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables, bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate, were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a pl ant trial. The target firing temperature at the Empire Plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets

Jan 1, 1985

By d&apos, I. J. Agati

The stockpiling and reclaiming of bulk materials can be a challenging task for engineers seeking the optimum solution for plant needs, reliability, and at lowest unit cost. The objective of this paper will be to expose advantages, disadvantages and limitations of many storage and reclaiming systems to the responsible engineer and management. The paper will emphasize the practical aspect of stockpiling and reclaiming methods. Many valuable and interesting papers are available dealing with the theoretical viewpoint and application of a particular manufacturer's machine. Several of these are mentioned in the bibliography. As many practical parameters as possible will be given. After twenty years in the field of designing and selling bulk materials handling systems, the needs of the user and the plant are recognized and reasonably understood. This paper cannot give solutions to all problems In this vast field but will stress practical applications and examples of various installations. The evolution of advancements in materials handling is based upon not only technological innovations, but learning from many experiences of others and utilizing them as stepping stones to improved installations.

Jan 1, 1969

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By T. S. Lundström, B. D. Marjavaara, I. A. S. Larsson

"The flow field in a rotary kiln, used in an iron ore pelletizing process, was investigated using a three-dimensional computational fluid dynamics model. The model is isothermal, downscaled and simplified. The objective was to examine the possibility of capturing the unsteady motion of the flame seen in the real kiln. The results from the simulations were compared with recorded images of the real process. The results demonstrate the possibility of quickly getting an overview of the flow field in the kiln. The main, unsteady behavior of the flame was captured. The model may be used as a tool in the ongoing work of improving and optimizing the pelletizing process.IntroductionThe pelletizing process, in which the crude iron ore from a mine is upgraded into pellets, is a process involving large amounts of hot air flowing in complex geometries. Flow control is a crucial factor in this process to maintain high pellet quality. The rotary kiln is one of the last steps in the pelletizing process, and this is where the pellets are sintered to increase their strength and metallurgical properties. The kiln burner produces a flame that supplies the entire pelletizing process with the necessary heat.Kiln burner flames are large diffusion flames arising from a jet of fuel from the burner issuing into a concentric confining cylinder with a surrounding coflow of air, called secondary air. To enable combustion, the secondary air needs to be entrained into the fuel jet. This mixing of the fuel and air is the slowest step in the combustion process and therefore affects the efficiency of the combustion. The rate of entrainment depends on the momentum ratio between the burner jet and secondary air. The higher the momentum ratio, the faster the entrainment rate and, consequently, the faster is the fuel/air mixing.The kiln of interest in this study differs from kilns used in other industrial processes in both geometry and operating conditions. A distinguishing feature is the large amount of secondary air being induced through the kiln hood and then transported to earlier stages in the process as air or exhaust gas. The secondary air therefore has a substantial momentum, implying that the resulting flow field has a significant impact on the mixing and combustion process in general and the flame shape and stability as well as combustion efficiency in particular. A systematic study of the factors influencing the dynamics of the flow field in the kiln, neglecting the combustion, is therefore justified."

Jan 1, 2016

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By Pieter Hoekstra, Jim Hild, Mark Blohm

In the Basin and Range Province of Nevada, geophysics is used to assist exploration for bulk minable gold deposits, particularly over pediments. It is employed for mapping thickness of alluvium and Tertiary valley fill, for mapping covered structures, and for identifying alteration zones. In addition to potential field and seismic methods, three different electrical and electromagnetic methods are frequently used, resistivity-induced polarization, controlled source audiomagnetotellurics, and time domain EM. A review and comparison of the principles of these methods, illustrated by case histories, is the topic of this paper.

Jan 1, 1989

By L. M. Nuelle

Rare earth element (REE)-and gold-bearing breccia pipes are a potentially significant economic target in the Pea Ridge iron ore mine, Washington County, Missouri. The Pea Ridge deposit is one of eight known volcanic-hosted iron ore deposits in the Middle Proterozoic St. Francois terrane, which are similar to the Olympic Dam-type deposits of Australia. The iron orebody is steeply dipping, tabular-shaped, and cuts across the host rhyolite. The footwall of the deposit is zoned from the massive apatite-bearing magnetite core outward to heterolithic breccia, pseudobreccia, specular hematite zone, to an extensive silicified zone. The hanging wall is zoned from the massive magnetite core outward to a heterolithic breccia, pseudobreccia, and an amphibole skarn zone. The REE-rich breccia pipes cut through the various lithologies along the footwall at or near contacts. They are typically 60 m long, 15 m wide, and extend at least 120 m vertically. The pipes are comprised of fragments of rhyolite host rock, massive magnetite zone, specular hematite zone, and silicified zone rocks supported in a matrix of rock flour, barite, feldspar, monazite, apatite, chlorite, xenotime, and, locally, gold. Total REE oxide content of samples of the ground mass material, which are not diluted with lithic fragments, average about 20 weight percent. Grades from working faces in the mine are lower and average about 12 weight percent. Gold distribution is erratic, but concentrations are as high as 371 parts per million.

Jan 1, 1991

By C. L. Lin

The characterization of rare-earth resources in 3D is now possible using high-resolution X-ray microtomography (HRXMT) to describe ore texture and mineral phase composition. In addition, detailed texture analysis, including grain exposure and mineral association, can be described. Preliminary examination of a sample of Mountain Pass ore is reported to describe the spatial distribution of the mineral phases (calcite, barite and bastnaesite), particularly the grain size distribution of bastnaesite. The examination includes analysis of selected particle size classes to determine the appropriate size for liberation of the rare-earth mineral bastnaesite. Good liberation is expected to be achieved if the material is ground to a top size of -150 µm.

By Kirk L. Prather

Why discuss techniques of accident prod lot on? Would it not be more useful to discuss means to reduce accidents? This discussion will answer these questions by suggesting ways in which effective accident prediction techniques improve the ability to foresee and prevent accidents. Accident Prediction Process The secret to accident prediction is to utilize the tendency for history to repeat itself. The same circumstances and the same human behavior that produced accidents in the past tend to produce accidents in the present and the future. The ability to predict accident occurence in the future by projecting from the past is a statistical process. In a bookmaker's jargon this means "playing the odds" or "the percentages". A horse or a sports team may be beaten on any given day, but by skillfully assessing the factors of past performance and assigning odds, many clever bettors make money in the long run.

Jan 1, 1973

By Gabriele Eccher, Michele Caponero, Paolo Cucino, Roberto D’Angelis

"This paper describes the optic fiber structural monitoring system implemented for Pavoncelli Bis tunnel. The paper highlights the optic fiber sensors customization capabilities, how they smoothly fit precast concrete lining processes and TBM operations, and how a lifelong service monitoring can be achieved. An overview of readings’ evolution during excavation concludes the paper.INTRODUCTIONPavoncelli Bis is a 10 km hydraulic tunnel designed to by-pass the existing Pavoncelli tunnel which experienced severe damages during the 1980 Irpino-Lucano earthquake, in south of Italy (Barla 2009). Pavoncelli Bis excavation work commenced in 1988-90, however, when excavation approached pk. 0+583 in 1992, water percolations became more and more consistent and resulted in work suspension. The tunnel was eventually sealed at pk. 0+383, leaving a flooded section between pk. 0.383 and pk. 0+583. Work resumed in 2012 where EPB-TBM excavation was adopted to cross the flooded section and to overcome complex hydro-geological conditions in various lito-types and, in particular, in the Varicolori Clay-shales area (Figure 1).Consequently, stress evolution monitoring is extremely important during construction and during the service life of tunnel lining in clay-shales and in faults areas. In particular, the paper focuses on the monitoring system proposed for the newly EPB-TBM excavated portion from pk 0+583 onwards where optic fiber sensing technology was chosen for its reading stability and reliability in presence of water and its ability to be connected in series and remotely interrogated at kilometers of distance. FBGS OPTICAL FIBER SENSOR TECHNOLOGYFiber Bragg Grating Sensors (FBGS) are gaining increasing attention in the field of experimental stress analysis. Basically, Fiber Optic Bragg Sensors are strain-measuring devices and therefore provide many of the advantages of the well-known metal foil strain gages (Kreuzer 2007).Bragg gratings are written into so called single-mode fibers. These fibers consist of a very small inner core of 4 to 9 µm diameter and an outer part (cladding) of pure glass (SiO2) of 125 µm diameter. The difference of refraction indexes between inner core and cladding causes the light to propagate only inside the small core."

Jan 1, 2016