Search Documents

By George Bárdossy

Most of the bauxite deposits in Europe belong to the karst type. They are located mainly ill Southern Europe along the Mediterranean Sea and in the Ural Mountains. Lateritic bauxite deposits occur on the Russian Platform, in Poland, Northern Ireland and in Turkey. Tikhvin-type deposits arc found on the Russian Platform. Bauxite formation in Europe started in the Middle Devonian. The main bauxite forming period was the Upper Cretaceous. Very few bauxites are younger than Eocene. Most deposits are covered by overburden of up to 1000 m. Prospecting is carried out by drilling. Several geophysical methods are used to detect the hidden deposits. Geostatistical methods were introduced in several countries for evaluation of the reserves and the geometry of the deposits. Data on bauxite production are given for 1982 and since the beginning of mining in Europe.

Jan 1, 1984

By Andrzej Wala

Constantly increasing demand for energy materials and metal ores brought about tremendous progress in mining techniques which are characterised by a high degree of mechanization and concentration of works. One of the recent trends in underground mining mechanization is connected with an application of heavy machines with diesel engines [l],[2]. The introduction of diesel engines in mining all over world caused not only improvement in economic conditions but also the necessity to prevent contamination of air in the mine by toxic agents in diesel exhaust emissions. A generally used way of eliminating exhaust gases is proper ventilation of the cross cut by means of providing permanent exchange of air that would guarantee in every point of the cross cut and in every moment the decay in concentration of exhaust gases beyond threshold limit [3][4][5][6][7][8][9][10]. The present paper is an attempt to define a mathematical model describing the changes of concentration in cross cut face to which fresh air is distributed by ventilators and tubes in a forcing way. Obtained model should offer its practical adaptability to engineering calculation of the amount of fresh air needed for diluting and eliminating exhaust gases beyond threshold limit. Justness of these models has been confirmed by investigation of the growth of nitrogen dioxide concentration in air environment in some cross cut faces of Kiirunavaara iron ore mine in Kiruna (Sweden).

Jan 1, 1980

By Wen L. Cai

This paper examines the effects of different block dimensions and cone bases on the economic open pit limit design based on case studies on a coal deposit consisted of two west- east elongated, near vertical thin seams starting with a base model dimension of 200x170x50 (NX*NY*NZ) with a block dimension of 10mx5mx4m (DX*DY*DZ), the blocks were combined along easting, northing and elevation directions. Two cone bases were used, one with a base radius of 10 meters, the other with a base radius of 0. Two pit design algorithms, one is the floating cone algorithm, the other is an optimum algorithm, were used to see which one of the two pit design algorithms is more sensitive to block dimension and cone base variations. The results are presented and analyzed.

Jan 1, 1992

By B. K. Mishra, R. K. Rajamani, R. Venugopal, P. Songfack

Millsoft is a computer-simulation software that predicts the performance of large industrial grinding mills. This software surpasses all other tumbling-mill analysis techniques available today because it is based on fundamental laws of physics instead of empirical correlations. Graphical user interface (GUI) forms simplify the specification of the following design and operating parameters: mill diameter, length, speed, charge density and size distribution, lifter material and geometry. All of these parameters are taken into account in the discrete element numerical technique that constitutes the essence of the simulation software. In turn, the software produces a visual animation of grinding-charge motion, predicts mill power and gives the distribution of impact energy. In this paper, a case study of an 8.5-m-(28 ft-) diam SAG mill is used to illustrate the application of Millsoft for mill design and trouble shooting.

Jan 1, 2000

By Chee Theng

"Keep calm and carry on mining. That has long been the conventional wisdom in the mining industry, a largely cyclical one that has weathered roller-coaster booms and busts. But in the years from 2002 to 2016, an unprecedented steep rise in commodities prices that lasted a decade and then took a sharp turn downward had made it hard for gold and silver miners to stay the course.“The last 15 years highlighted some of the structural and inherent challenges that our industry has, from product price uncertainty to long lead times to the capital intensity of our business,” said Mitchell Krebs, president and chief executive officer of Coeur Mining, who was the luncheon speaker at the American Exploration & Mining Association’s 122nd Annual Meeting held Dec. 5-9, 2016, in Reno, NV.Looking back, Krebs said, “We were given this enormous gift of a commodities super cycle, and the industry kind of blew the opportunity.” While gold prices rose 319 percent and silver prices rose more than 200 percent over the 2002 to 2016 period, the XAU index of 30 gold and silver mining companies’ stock prices went up by only 20 percent.Entering 2016, precious-metals prices have made a comeback, with gold rallying strongly from a six-year low at the start of the year. This time, the industry is ready. Companies are leaner and meaner, with lower costs, reduced debt and an increased focus on higher grades and quality ounces. Although opportunities were missed in the past, the industry has got its act together and is now well positioned to take advantage of a price upswing and even to show profits when prices fall, as they did in August 2016, pushed down by a strong dollar."

Feb 1, 2017

By A. F. McKown, P. E. Sperry, W. L. Fourney, D. E. Thompson

INTRODUCTION Underground drill and blast excavation is usually accomplished with small diameter holes loaded with high energy explosives. The detonation pressures are extremely high and an extensive amount of energy is dissipated in the process; however, very little of this energy is used to create the specified fracture planes required for excavation. The available energy is expended in producing radially outgoing stress waves, in crushing the adjacent rock, and in producing a dense, randomly oriented radial crack pattern about the holes. This causes several undesirable effects: 1. Overbreak at the perimeter, which results in more muck to remove and extra concrete or shotcrete to fill the voids. 2. Damage to or loosening of the remaining rock at the perimeter which may result in the need for additional support measures. 3. Ground vibrations and/or airblast, which could result in damage to nearby structures and complaints by people living or working in the area. Several steps may be taken to minimize these effects. Where control of the perimeter is desired, smooth blasting techniques are generally employed in which the spacing and burden of perimeter holes are reduced and lighter, decoupled charges are used. Where vibration damage to structures is feared, control is generally exercised by limiting the charge weight per delay period so that the ground vibrations at the nearest structure do not exceed a peak particle velocity of two inches per second. Where blasting complaints may be a problem, con-

Jan 1, 1979

By Jie Li, Longxiang Li, Wenbing Guo, Gaobo Zhao, Yuhang Hu

Surface subsidence caused by underground longwall mining is a very complicated process in time and space, influencing building and structures on the surface of the mining area, including houses, pipelines, and highway. The field monitoring data of surface subsidence are essential for protecting them. This study investigated the dynamic and residual subsidence characteristics of both the surface and the highway over a 730-day monitoring period on a longwall panel. Three monitoring lines (Lines 1–3) were established to monitor the subsidence process, and three stages were identified: initial stage of surface subsidence, active period of surface subsidence, and residual subsidence deformation stage. The maximum subsidence value on the highway (1,786 mm) was smaller than that on the surface (2,094 mm), and the maximum subsidence velocity on the highway (41.7–50.8 mm/day) was also lower than that on the surface (66.7 mm/day). During the residual subsidence deformation stage, both the surface and highway subsidence velocities decreased to below 0.6 mm/day. Furthermore, differences in subsidence characteristics between the surface and the highway were analyzed, with the subsidence value on the highway always being less than that on the surface, while the subsidence velocity during the residual deformation stage was not always lower. This could be attributed to the influence of dynamic loads from vehicles, which could induce additional residual subsidence on the highway. Further investigation into this phenomenon will be conducted in future research.

Jul 1, 2023

By Thomas C. Atchison, James J. Olson

INTRODUCTION Technologic progress depends on new and innovative ideas, the practical application of these ideas, and finally as the technology is developed and demonstrated, the engineering improvement or replacement of existing capabilities. In many areas the new ideas, although known, are not immediately put to practical use in all applicable fields. Good technologic forecasting for research and development within the excavation field coupled with adequate technology transfer is necessary to ensure timely application of innovative ideas to remove bottlenecks in the total system. The purposes of this paper are (1) to show the potential ability of technologic forecasting to meet future demands in rapid excavation through the acceleration of excavation rates by research and development in several related technologic fields, (2) to provide a brief review of the initial development of the ARPA (Advanced Research Projects Agency) Rock Mechanics and Rapid Excavation Program, (3) to draw attention to the research projects completed or underway in the FY 1970-1972 ARPA program and explain where information or program results can be obtained, (4) to summarize the progress and accomplishments of applied research contracts in the rock disintegration element of the ARPA program, and (5) to discuss the research directions planned for the remaining years of the program. The Advanced Research Projects Agency (ARPA) is a group within the Defense Department responsible for conducting basic and applied research and development for advanced projects assigned by the Director

Jan 1, 1997

By David Maust, Rob Albinger, Mike Walling, Michael Rispin

The safeguarding of health and life is the number one priority for underground infrastructure projects. While culture and approach are critically important, the industry has also seen the development of innovative tools and technologies that assist in making the underground environment and working places more safe and secure, both on an everyday basis and in the event of an unexpected occurrence.

Dec 1, 2022

By J. Raatikainen, I. Auranen

"INTRODUCTION Sorting technology has advanced rapidly recently. Of the two possibilities particle sorting has advanced especially in introducing new sensors and the use of multiple sensors. The analyzing and computing lead times have also shortened. This has made it a viable technology option for many applications but not for the most important sorting task at a mine; the run-of mine ore. Bulk sorting, however, has advanced in smaller steps, even if the technology has the capability to tackle the run-of-mine ore and offers a high potential to bring mines substantial economic benefits. The sensors, which are useful are restricted by the difficult operating conditions or by the ore characteristics. One of the important features of run-of-mine sorting technology is the major material handling infrastructure required. The capital expenditure can be substantial requiring good understanding of the sortability curve (grade-recovery curve) behavior of the ore. This paper discusses one industrial case, where substantial amount of data measured from the ore feed belt has been obtained. This data was then analyzed for the grade recovery curves obtainable from that ore with sorting. EXPERIMENTAL The XRF measurement used was the FCA device from IMA Engineering (Fig.1). It is a specially built version of XRF designed to operate with coarse material. The measurement was situated at the main belt conveyor taking ore from the primary crusher to the stockpile. The crushed ore was about 80% -300 mm at a capacity of 1100-1200 tph (Fig.2). Measurement times were varied from 30 seconds to a minute. Measurements were obtained over several months.As the XRF is a surface distribution measuring technique, the measurement was first tested upon accuracy and reproducibility against plant daily wet chemical assays and against on-line Courier feed analysis. As there is a varying delay in the ore stockpile, the delay time was used as a variant in the validation. Different measurement times were tested for accuracy. A one minute measurement time gave a total measurement relative standard error, which was both for Cu and Ni below 3%. The results showed also very robust correlations; for Cu, the correlation coefficient was R > 0,94 for one minute measurements over three months and R > 0,86 for Ni respectively. Fig 3. Shows a measurement period of two hours showing substantial feed grade variations (given as relative value; 1.0 represents the mean value during the measurement month)."

Jan 1, 2018

By W. Blake, J. Mahaut, W. Hustrulid

Division II at Kamoto mine in Kolwezi, Zaire represents a transition zone between Divisions I and III where transverse and longitudinal cut-and-fill rooms were being mined. Because this transition zone had been geologically depicted as being badly faulted the mining in this division had been deferred to a future time. However, to increase production and to reduce mining costs by carrying out the mining of the 3 divisions simultaneously, it was decided to mine Division II. The mining research group of Gecamines was given the task of designing a mining geometry then testing this design in a full scale test. Based on an evaluation of the faulting and fracturing of the 2 parallel orebodies and on an extensive in situ testing program preliminary mathematical analyses were used to develop and evaluate room and pillar designs in the 35°-65° dipping bedded formations. Based on these analyses and the constraints of having to fit the design of Division II to grade into Divisions I and III in a logical manner, a mining geometry for Division II evolved. To test this design an instrumented room was excavated in the most critical area. The results of this full scale testing showed that the behavior of the roof and wall rocks were as had been predicted by finite element computer model studies which incorporated the material properties and results of the field testing. The room geometry design was both judged and observed to be stable, hence mining commenced.

Jan 1, 1977

By Ronald M. Fedrick

The microtunneling project for the State of Hawaii's Natural Energy Laboratory (NELH) facility in Kona, Hawaii, was awarded to Nova Group Inc., Napa, California. Nova has developed both microtunnel and deep pile cofferdam experience. Both of which would be required for this project. The project was designed by Makai Ocean Engineering of Honolulu as a continuation of the Ocean Thermal Energy Project (OTEC). The world's first OTEC plant has been successfully operational at NELH since 1982 netting approx 50 kw of usable electric power from a gross generation of 210 kw. A second plant designed to draw 39°F cold water from 3,000 ft below sea level and produce a gross output of 1 mw with a net 500 kw of usable power required 2 - 54 in. finished diameter pipelines. An ongoing problem with earlier offshore pipelines has been the damage to the near-shore pipes within the surf zone. The necessity for a deeper connection between the land based pipe and submerged sea pipeline was obvious. Earlier pipelines had been drilled and shot through the shoreline. This process was only practical at shallow depths. Makai Ocean Engineering and the NELH scientists looked at different methods to get the pipeline through the shoreline at a depth of 80 ft below sea level. Initially, the direction drilling method was proposed as the most potentially practical method. A contract was awarded and various attempts were made to complete a successful

Jan 1, 1995

By P. E. Nielsen, T. L. Loga, B. B. Mauko

A numerical model is presented which simulates the dynamic fracturing process for a circular geometry fracture in a uniform stress medium. The dependence of crack aperture and net pressure in the crack upon various dominant parameters of the fracturing process is discussed. An analysis of a 75% nitrogen foam fracture in a coal seam at 5600 feet (1707 m) is also presented. The analysis is based upon the discussed parametric trends, the job records of treatment parameters, and a Nolte plot of net downhole pressure. It is interpreted that fracturing with water, in pre-foam fracture pump tests, resulted in significant fracture height growth. However, the subsequent foam fracture had reduced height growth due to the high effective viscosity of the foam and due to the higher magnitudes of elastic modulus and stress in the bounding rock strata with respect to the coal.

Jan 1, 1986

By R. J. Hickson

From 1993 through 1999, Cyprus Amax Minerals successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized and an environmental issue was appropriately remediated. The projects stretched over three continents: from arctic Russia to the Atacama Desert, from sea level to an elevation of 4,900 m (16,00Oft), from city suburbs to remote wilderness and from a low of US$130 million to more than US$ 1billion. The operations included open-pit and underground mines, mill and leach facilities and involved gold, copper, molybdenum and coal. The diversity of these projects inspired Cyprus Amax to create a "best-practices” project-management protocol to steer corporate expansion in the new millennium. This paper summarizes these best practices, while highlighting the project-management pirfalls to avoid.

Jan 1, 2000

By G. Belardi, G. Marruzzo, P. Plescia

This paper presents the results of grinding tests performed on magnetite from Kiruna (Sweden) and on chromite from Skoumtza (Macedonia. Greece). Stresses were measured by XRD, which determined the variations in the characteristic structural spacings of the minerals both before and after, grinding in a HSM/250 Herzog laboratory ring mill. Anal Isis of the magnetite and c hromite crystallinstallin was performed hi measuring the broadening of the strongest diffraction peak (311). .Also, structural analysis on chromite was carried out using the Mikheev model. Ultrafine-grinding tests on the magnetite and chomite demonstrated that this type of treatment can induce profound variations m the surface-stress state. These included plastic variations of the cell followed by "chemical" stress with oxidation front the stricture to form hydroxide or carbonate, films. This can have a great influence on the mineral reactivity to flotation reagents

Jan 1, 1996

By Edwin A. Blackey, Joseph G. Engels, James T. Cahill

An extensive geotechnical instrumentation program was undertaken during the construction of a 6.7 m (22 ft) inside diameter tunnel to monitor the ground-structure response and to check assumptions made for design. The tunnel was advanced through sedimentary and igneous rock using a fully shielded tunnel boring machine (TBM) with both temporary support and final lining provided by precast concrete liner plates erected in the tail section of the TBM. The parameters measured and evaluated include rock deformation, strain in the precast concrete liner, changes in tunnel cross section and groundwater response. In addition, an automated camera system is described which was mounted on the TBM to provide a continuous photographic record of the bedrock conditions exposed at the tunnel springline. The performance of various types of instrumentation equipment in an underground construction environment is also evaluated.

Jan 1, 1981

By W. Pariseau, J. Goris, S. R. Dismuke

Ore at the Magmont mine in southeast Missouri is extracted by the room-and-pillar method on two and sometimes three horizons. In 1991, a plan was formulated to recover high-grade ore in pillars using cable halts to accommodate spans of more than 27 m (90 ft ). A test area was selected and a recovery plan developed. A cooperative rock mechanics study was established by Cominco Metals, the US Bureau of Mines and the University of Utah. When initially opened in 1968, the planned production rate was about 910 kt/a (1 million stpy). Due to declining reserves, the production rate was decreased in November 1992 to 570 kt/a (630.000 stpy). Pillar recovery now accounts for about 40% to 50% of the mined tonnage. This method plays a vital role in allowing Magmont to continue to operate.

Jan 1, 1996

By E. L. Bohnet

The purpose of this paper is to translate a mining company's "Corporate Objectives" into usable and practical guidelines for long term mine design and production scheduling. These guidelines are required to ensure that both operating and development properties are designed and economically ranked on the same basis, and with the "current" Corporate Objectives in mind. Secondly, if both management and mining engineers have a better understanding of the cause and effect of corporate policies, then penalties and risks associated with various Corporate Objectives can be put into better perspective for management. Corporate Objectives, relative to usable guidelines for either short and/or long term mine planning, could be defined as one or more of the following four objectives: 1) Maximize the recovery of the economic portion of the defined geologic resources, and hence, maximize total non-discounted project cash flows and profits (most common approach in mine design), 2) Maximize the Net Present Value (NPV) of the after-tax cash flows from each existing or proposed project, either on an individual basis or in concert with other projects, including downstream processing facilities (primary method used to judge relative investment merit of a proposed development or operating concept), 3) Limit short and long term capital expenditures to a defined ceiling, 4) Maximize product output for the existing facilities in the short term, or conversely, keep commodity production at a constant level for a series of years.

Jan 1, 1994

By Bob Gordon, Allen Furth, Dan Dobbels

A 4.8 m (16 ft) diameter hard rock tunnel was driven through granite bedrock to create the 1.7 kilometer (1.1 mile) long Hampton McCloy Retention Tunnel for the city of Richmond, Virginia. During the work the tunnel encountered narrow seams of partially decomposed granite that were not self supporting and could be dealt with using ribs and lagging. However, as the tunnel approached the receiving shaft, it encountered a large seam of highly decomposed rock, alluvial deposits and running sand which resulted in soil loss into the machine. As a result of this condition, a jet grouting program was quickly developed to allow the tunneling to continue. This paper will describe the manner in which jet grouting was used to solidify and stabilize the decomposed bedrock, alluvial soils, and running sand to allow the TBM to continue tunneling.

Jan 1, 2003

By A. Pavlidis

This paper investigates variations of lignite quality attributes with geostatistical methods. The study focuses on lignite from the Southern Field in the Greek province of West Macedonia. The targeted quality variable is the ash water-free content (AWF). A geostatistical model is constructed based on data from 480 drillholes (approximate drill hole spacing of 250m). For each drillhole, the vertical average of the AWF is calculated. The coarse-grained AWF is then modeled as the superposition of a trend surface and fluctuations. The spatial dependence of the fluctuations is modeled by means of the experimental variogram. Kriging estimators are used to determine the AWF values on a rectangular grid, and the uncertainty of the estimates is calculated. Implications of the analysis for the variability of the produced lignite are discussed, and recommendations for additional drilling are proposed.

Jan 1, 2006