Search Documents

By Yury Kapelyushin

Formation of cementite in the reduction of hematite by CO–CO2 gas was studied in situ using high temperature XRD (HT XRD) analysis. Reduction of hematite was examined in the temperature range 873–1173 K by CO–CO2 gas mixture with high carbon activity. When carbon activity in the system was 1.5, cementite was formed only at 1023 K; it was not observed in experiments at 973, 1073 and 1123 K. Formation of cementite was observed at 923–1073 K when carbon activity increased to 3–5; and at 873 K when carbon activity was 10. Formation of cementite at 973–1073 K proceeded through metallic iron; however, in the reduction of hematite at 873 and 923 K, iron was not observed; cementite apparently was formed directly from wüstite. XRD spectra were used to estimate concentration of carbon in austenite in the process of cementite fromation.

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By S. Raghavan

The thermodynamic activities of MgO in the solid solutions that can exist in the system NiO-Mg0-Zn0 are determined by measuring the EMF of the cell: O2 (g), Pt / MgO, MgF2 // MgF2 // x MgO + yNiO + (1-x-y)ZnO / Pt, O2 (g) / MgF2 in the temperature range 1190-1237 K. Equilibrium phases were prepared along the quasi- binary lines MgO/NiO = 0.1765,0.3333, 1.0,3.0 and 5.667 with the ZnO contents being 0.1, 0.2, 0.25, 0.35, 0.5, 0.75 and 0.9. The crystal structures of the phases were identified by X-ray diffraction. Results obtained so far show that a single phase MgO-rich cubic solid solution exists upto 0.2 ZnO content and for compositions above 0.25 ZnO, a second ZnO rich wurtzite phase forms in addition. Activity measurements show that for low MgO and ZnO contents, the MgO activities exhibit ideal to slight positive deviation from ideality and at higher MgO contents, a negative deviation is shown. Further studies are in progress.

Jan 1, 1993

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 um fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 um. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1991

By G. R. Palmer

The success of future electric vehicles will depend greatly upon the power supply choices made today. Research is presently being conducted by automotive engineers and electrochemists to determine what battery type may be the most promising. Not only are product production and application efficiencies being evaluated but also environmental concerns of reclamation and recycling. Rechargeable batteries using nickel-metal hydride electrodes are strong candidates for these electric vehicle applications. The U.S. Bureau of Mines is investigating hydrometallurgical technology that separates and recovers purified metallic components present in nickel-metal hydride battery scrap. Sulfuric, hydrochloric, and nitric acids are all capable of dissolving the battery electrode alloys given the proper operating conditions. Solvent extraction of the leach solutions using D2EHPA removes iron, and selective precipitation shows promise of recovering the other metals in the H2SO4 and HNO, systems.

Jan 1, 1994

By Rong Zhu, Guang-sheng Wei, Kai Dong, Ling-zhi Yang

As a shortage of information technology support, steel plant is unable to real-time tracking production cost of each working procedure, and can’t form the information feedback in time. Information integration technology for dynamic monitoring becomes a development trend of process control in advanced iron and steel enterprise. The paper based on the characteristics of EAF steelmaking process and requirements build the digital platform and process guidance model, which is designed to solve for smelting composition control, cost control, and optimizing guide in EAF steelmaking process. The model is including: data acquisition module, cost monitoring and calculation module, EAF endpoint carbon control module, alloy material optimization module, component monitoring and forecast module, process guidance module, data maintenance and query module.

Mar 1, 2018

By Richard D. Hagni

Polished sections of pyrometallurgical intermediate products from a simulated commercial flash furnace were examined by reflected light microscopy, scanning electron microscopy-energy dispersive spectrometry and electron backscatter analysis, and microprobe analysis for phase and textural relationships. The smelter feed is a copper concentrate from a porphyry copper deposit. The concentrate consists primarily of chalcopyrite, bornite and pyrite with smaller amounts of covellite, chalcocite, molybdenite, magnetite, galena, and sphalerite. The flash furnace reactions for pyrite and chalcopyrite can be observed by reflected light microscopy. Reacted angular particles of pyrite exhibit successive rims of fibrous pyrrhotite and hematite or magnetite. Reacted angular chalcopyrite particles show successive rims of bornite, digenite, and chalcocite. Spherical particles, formed by the complete melting of former pyrite particles, consist of variable amounts of granular pyrrhotite with magnetite rims and minor hematite. Spherical particles, formed by the complete melting of former chalcopyrite particles, exhibit exsolution intergrowths with varying proportions of intermediate solid solution, bornite, digenite, and chalcocite and have rims of hematite, magnetite, and copper-iron spinel. Sphalerite and molybdenite do not show evident mineralogical reactions.

Jan 1, 1987

By Toshiro Kuji, Masakazu Fujita, Tetsuji Saito

"The magnetic properties of the magnetic materials were deeply dependent on the microstructures. In this study, the novel technique to produce the desired microstructures in a controlled manner was proposed. The technique consisted of the production of the amorphous alloys and the control of the crystallization process. The technique was applied to improve the magnetic properties of Nd-Fe-B permanent magnets. The microstructural control of the magnets exhibited the excellently high energy-products of higher than 430 kJm-1. The relationship between the magnetic properties and the microstructures of the Nd-Fe-B permanent magnets was discussed.IntroductionThe intrinsic properties of the materials are basically determined by the properties of the constituent elements or the compounds. However, it is often noticed the difference between the observed properties and the theoretical values expected from the intrinsic properties of the materials. This indicates that the observed properties of the materials are determined not only by the properties of the constituent elements. In other words, the observed properties of the materials are also strongly dependent on the morphology of materials. This means that the microstructural control may creates a great improvement of the properties of materials.In Nd-Fe-B permanent magnets, the superiority arises from the uniaxial intermetallic Nd2Fe14B compound which has a large saturation magnetization and a high anisotropy field [1,2]. The magnetic properties of the Nd-Fe-B permanent magnets are dependent on the microstructure, that is, the size, shape and degree of the crystallographic alignment of the Nd2Fe14B phase. Currently, the Nd-Fe-B permanent magnets have been produced by either sintering or melt-spinning [3,4]. In the sintered magnets, alignment of the Nd2Fe14B phase is achieved by the prior green compaction of the crushed ingot powders in an applied magnetic field [3]. In the melt-spinning approach, alignment of the Nd2Fe14B phase is achieved by hot deformation [5]. Amorphous melt-spun ribbons are comminuted and then are consolidated into bulk form by hot pressing before hot deformation. As-hot-pressed magnets have randomly oriented Nd2Fe1~ grains [6]. Subsequent die upsetting of as-hot-pressed magnets gives rise to the crystallographic alignment of the Nd2Fe14B phase."

Jan 1, 1998

By Leonard J. Friedman

The recovery of sulfur dioxide from metallurgical gases for the production of sulfuric acid has been an effective means of reducing sulfur dioxide emissions from non-ferrous smelters. Sulfuric acid has been produced from gas originating from fluid bed roasters, electric furnaces, reverberatory furnaces, flash smelting furnaces, Pierce Smith and flash converters, sinter machines, etc. The gas from each of these sources has a unique set of variables that affect the design and operation of the sulfuric acid plant. In addition, the sulfuric acid plant itself has been evolving, with new equipment designs and materials. This paper will review each of the unit operations in the gas cleaning and contact sections of the metallurgical sulfuric acid plant, discussing various equipment designs, materials and the handling of gas stream variables and impurities. The paper updates to 2006 previous works on metallurgical sulfuric acid plants by the authors.

Jan 1, 2006

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Jean-François Boulanger

The production of rare earth elements from ore usually consists of three steps; the separation of a concentrate of REE bearing minerals; the cracking of the REE minerals to liberate the REE into an aqueous solution and separation of REE into individual elements. This paper describes the results of laboratory tests conducted on a carbonate-rich REE ore containing bastnaesite and monazite. The tests cover the whole processing sequence of beneficiation, preparation of the REE solution using a caustic leach followed by acid leach to break monazite and bastnaesite and liberate REE into an aqueous solution and the partial separation of the REE using solvent extraction. Details on the product quality and process performances (recovery and impurities removal) are given for each studied step. The paper also discusses the economic advantage of separating the REE rather than producing a mixed REO product to be sold to a refinery for REE separation. A mini-pilot plant version of the process is currently planned.

By Robert J. Stevenson

The chemical variation of central North American lignite fly ash can be compared using the major and minor oxide analyses and the distribution pattern of the inter-grain chemistries of the individual fly ash have been used to illustrate the variations in bulk ,sample and individual grain chemistry. This information documents the chemical variability of the lignite fly ashes by geographic region. There is a direct relationship between grains rich in SiOa and AlaO, and in the NazO content of the grains in lignite derived fly ashes. There is also a direct relationship between grains rich in Ca0 and the MgO and SO, content of the grains in lignite derived fly ashes,. These variations are shown using CaO-SiO2-Al2O3 and CaO-Na2O-MgO ternary diagrams.

Jan 1, 1992

By D. Valic

In 1997, 9.2 million tonnes of mined, recoverable copper was produced, of which, 1.8 million tonnes or 19.4% was produced by leaching, solvent extraction and electrowinning. The amount of copper produced by this method grew faster than those attained from concentrate smelting, signifying the growing importance of this low-cost production method. Statistical experimental design, unlike traditional approaches, allows for proper distribution of experiments within the boundaries of factors being studied such that the number of experiments required to develop a sound relationship between the factors and a response is minimized. In the past, very little use has been made of statistical experimental design in copper electrowinning studies. Traditional one- variable-at-a-time approaches are widely employed for this purpose. The present study employs a factorial experimental design to relate current efficiency with current density (180 and 300 A/m2), copper concentration (25 and 65 gL), and temperature (40 and 60 °C). Pure synthetic electrolyte with a constant acid concentration of 180 g/L was used throughout the study. The designed study produced a linear relationship where the independent variables of current density, copper concentration, and temperature, and their interactions, were found statistically significant. It was shown that current efficiency could not solely be used as a predictor of copper cathode quality. The quality of the deposit is difficult to be incorporated into a model or relation. It was determined that other measures, such as cathode morphology and crystal structure should be considered. This was done through XRD and SEM analysis.

Jan 1, 1999

By F. F. Aplan, G. Simkovich

"A review is given of the effects of solid state point imperfections upon a number of mineral benefication processes and a metal extraction process. It has been found in numerous flotation studies that small amounts of aliovalent impurities (dopants) in binary compounds may show major effects upon flotation behavior. Both semiconducting and ionic conducting compounds are affected. These effects are also seen in hydrometallurgical studies as well as in electrostatic operations. Additionally, de-copperization of lead melts appears to be strongly influenced by similar defects. It is hypothesized that the effects observed in these studies are present in actual operations and should be considered in designing processes. A few speculations concerning future efforts are advanced. IntroductionImperfections [point (e.g., vacancies, interstials, quasi-free electrons, electron holes, impurity ions), line (e.g., dislocations), two dimensional (e.g., grain boundaries) and three dimensional (e.g., 2nd phases) defects] are generally present in solid materials and these imperfections may, and often do, have important effects upon a variety of properties and processes. In general, one may, in most cases, attain elimination of three dimensional defects by a separation process of one type or another (e.g., gravity, electrostatic, magnetic, flotation, hydrometallurgical etc.,). Thus, this type of defect has rarely been investigated in a systematic fashion. Two dimensional defects are always present in non-single crystal materials but have also escaped systematic studies in processes primarily because the control of such defects is not easily attained. Line defects are non-equilibrium entities which are present in ill-defined quantities so that they present a variable that cannot be easily controlled although through careful systematic experiments one can attain some reproducible relations pertaining to this type of defect.Contrary to the lack of studies concerned with the effects of 1, 2 and 3 dimensional types of defects there has been some activity concerned with point defects and their effects upon a number of mineral/metallurgical processes, especially flotation processes. Thus, this article will present a review primarily of point defects in relation to their effects upon flotation although other processes and defects will also be mentioned."

Jan 1, 1988

By Monica C. Pinto, Gustavo H. Nalon, José C. L. Ribeiro, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Lucas A. F. Fioresi

This study aims to evaluate the influence of mortar’s mechanical properties on the behavior of clay masonry. Experimental studies were performed using prisms of clay blocks under axial compression. The clay units were produced with a clay from Tres Rios, Rio de Janeiro, Brazil and had compressive strength of 4.9 MPa. Two mortar compositions were used, which had compressive strength of 94.7 and 50.4% of the clay blocks’ net area compressive strength. It was noticed a slight increase on the prism’s compressive strength with the increase of the mortars’ compressive strength and stiffness. Prisms made with flexible mortars had a ductile failure and collapsed under lower compressive stresses, while prisms made with stiff mortars resisted higher compressive stresses, but had a brittle failure ,crushing the blocks. A very strong mortar is not recommended. Using more flexibl mortars does not compromise the strength and stiffness of the masonry and prevents an excessively brittle failure of the structure.

Mar 1, 2017

By M. J. Perpich

Electrochemical and chemical leaching tests were carried out on chalcocite, covellite and chalcopyrite in acidified iron sulfate solutions sparged with a mixture of O2 - SO2. The gas mixture catalyzed the ferrous to ferric oxidation reaction in situ and, therefore, increased the redox potential and oxidizing strength of the solution. Anodic polarization curves in dilute sulfuric acid on copper sulfide electrodes showed that chalcopyrite passivates and dissolves at current densities orders of magnitude less than chalcocite and covellite. The addition of a depassivating agent (Ag+) increased the passive current density of chalcopyrite and caused breakdown near 0.625 V (SCE). The depassivating effect was also observed during the leaching of chalcopyrite particulate samples as small amounts of Ag+ added to acidified iron sulfate solutions in the presence of O2 - SO2 mixtures greatly increased the leaching rate and the total amount of Cu oxidized (> 90%). Passivation was prevented in the absence of Ag+ by decreasing the initial oxidizing power of the solution and by pretreating the sample in a reductive leach. Both of these methods resulted in transformation of the chalcopyrite surface from its characteristic greenish-gold into deep black. Increased concentrations of Fe+++ due to 02 - S02 sparging were then able to oxidize the transformation product.

Jan 1, 1999

By Jeff M. Kuhn

A new solvent extraction process for the removal of halides from zinc sulphate solution was tested in pilot plants at both a 0.1-L/min scale and at a 3-L/min scale. Teck Cominco?s process is called the HalogonTM process, for which patents are pending. Mixer-settlers were used for the 0.1-L/min pilot scale and two BATEMAN pulsed columns for the higher rates. Pilot testing was performed with commercial zinc sulphate solutions containing variable amounts of chloride and fluoride. Sulphate extraction was also controlled and deleterious halides were loaded and stripped into a form suitable for disposal. The engineering aspects and economics of this solvent extraction process for halide removal are also reported.

Jan 1, 2003

By Peter Kettle

This paper describes the performance of the copper industry over a period of some two decades and examines the theme that improvements in operating efficiency have not been matched by improved returns on capital. The financial performance of the copper industry is analysed using CRU's MICA database. Regression analysis indicates a two percentage point increase in operating margins but no increase in returns on capital. The gain in operating efficiency appears to have been mainly achieved in the mid 1980s. The investment boom of recent years has resulted in a rapid increase in the industry's level of debt and gearing ratio (now some 47%). Data on 44 copper mine projects is used to show the linear relationship between scale and capital costs. Typically new capacity costs some US$5,000 /tpy. The relationship between cash costs and capital intensity of projects is also plotted. The greater attention now being focused on efficient use of capital means that capital intensity rankings will become increasingly important in determining which projects go ahead.

Jan 1, 1999

By Antoine Allanore, Luis A. Ortiz, Donald R. Sadoway

"The steelmaking industry has drastically reduced its energy consumption in the last fifty years, and today’s technologies are considered to operate at their optimal efficiency with respect to energy needs. To cope with new constraints related to greenhouse gas (GHG) emissions, a change of paradigm is necessary. One of the promising technologies that could be deployed to help reach CO2 mitigation targets relies on the intensive use of electricity: molten oxide electrolysis (MOE). This paper presents the key process parameters that need to be tuned to address the practical needs for both high productivity in a steelmaking reactor and for an energy efficient process. Herein we show that contrary to common perception, the electrolysis process for ironmaking requires less energy than today’s chemical reduction route. Furthermore, we prove that most of the energy that must be provided to operate the electrolytic iron production cell is thermal energy which is readily generated by joule heating during electrolysis due to large currents being passed through the electrolyte. The energy consumption of the electrolysis cell is therefore shown to be highly dependent on the cell configuration and the chemistry of the electrolyte. As a consequence, the CO2-impact of the technology strongly depends on both the power production mode and the technological choices for design of the process, including cell configuration. Surprisingly enough, even when the electricity generation is not carbon-free, MOE still appears to be viable from the perspective of reducing GHG emissions providing sound reactor design considerations are made.IntroductionIn the context of greenhouse gas (GHG) emissions mitigation, the steelmaking industry is considering several techniques that could sustain the efforts and progress achieved by this sector in the last decades [1]. A recent report [2] on potential routes for low-CO2 steelmaking highlighted for all techniques both the strong dependency of CO2 emissions on electric power production mode and the need for a decrease in energy consumption per tonne of steel. Incited to innovate with respect to this last criterion, the steel industry considers electrolysis to be a promising technological solution, and in particular the molten oxide electrolysis (MOE) process. This process conducts electrolysis in a mixture of oxides that dissolve the iron oxide feed, which by the action of electric current is decomposed into liquid iron and oxygen gas. The opportunity for reduction in energy consumption during steelmaking by MOE is commonly attributed to the “direct” pathway from iron oxide to liquid metal offered by the use of a molten oxide melt and operation at a temperature above the melting point of iron, ideally 1600°C, to provide enough superheat for tapping the molten iron product:"

Jan 1, 2011

By J. Phillip Mackey

The Peter Hayes Symposium on Pyrometallurgy, held as part of Extraction 2018, is an acknowledgement of his contributions to the basic science and principles underpinning modern pyrometallurgical processing. After completing his PhD at Strathclyde University, Scotland, in 1974, Peter took up a teaching position at The University of Queensland, Brisbane, Queensland, Australia in 1976. Peter Hayes’ research at the University since then has been focussed on: • The mechanisms and kinetics of heterogeneous solid/solid, gas/solid and liquid/ solid reactions, and • Experimental measurement of phase equilibria in complex high temperature metallurgical systems. This paper provides a brief biography of Dr. Peter Hayes and gives a full listing of Peter Hayes’ publications.