Search Documents

By T. A. Larssen

The efficiency in production of manganese ferroalloys is dependent on the gaseous reduction of the higher manganese oxides in the ores used as raw materials. The materials, descending in the furnace, will meet the furnace gas that contains significant amounts of CO(g) and reduce in subsequent steps, the last step being reduction of Mn3O4 to MnO. This step may to varying extent occur at temperatures exceeding 800 °C, i.e. in the active region of the Boudouard reaction. The gas reduction of Assmang and Comilog manganese ores were investigated in CO-CO2-atmosphere at temperatures up to 1000 °C. It was seen that decreasing ore size correlates to a lower reduction temperature and increasing reduction rate. Similar effect was observed with increasing CO-content in the gas atmosphere. Further, it was found that Comilog ore obtained a complete prereduction at 600 °C, whereas reduction of Assmang ore was not complete at 800 °C for the majority of the experiments.

By Liu Wei-feng

Base on the thermodynamic calculation of vapor pressure of lead, antimony and arsenic at high temperature, the possibility of separating lead, antimony and arsenic in different temperature was analyzed ,and the practice of producing qualified antimony white from lead-antimony alloy by direct blowing was introduced in detail in this paper. The blast furnace reduction smelting was brief introduced firstly, and then alkaline refining was applied to removing arsenic from lead-antimony alloy that contains As1%,Sb39%,Pb58%,the arsenic in the treated lead-antimony alloy could decrease to 0.009% by that method. The antimony white containing Sb2O3 99.5% could be produced by air blowing in the special furnace at 650? from the treated lead-antimony alloy. And the electrolytic lead could be achieved by electrolysis from the lead-rich alloy which contained 83% lead.With high-grade product being obtained the process was shortened. The technology has been applied successfully many years in Guangxi, China.

Jan 1, 2009

By C. R. Palmer

The Bureau of Mines investigated the use of ion-exchange technology for the recovery of precious metals from cyanide leach and spent electrolytic solutions. This research included adsorption of gold and silver on both weak-and strong-base anion-exchange resins. The effects of nickel, mercury. and iron on precious metal loading of strong-base resins were also determined. Due to the nonselectlvity of strong-base resins, selective elution also was investigated. Both commercially available and experimental weak-base anion-exchange resins were tested. None of the commercial weak-base resins tested were suitable for a caustic-cyanide system owing to their low recovery of precious metals at pH 10 or above; however, three experimental resins have possible application. Continuous tests conducted with mill cyanide solution in a multicompartmented ion-exchange column using strong-base anion-exchange resins adsorbed nearly 100 pct of the precious metals as well as the iron and nickel. During the elution of this loaded resin the iron was first removed with NaCI plus NaOH; then nickel with dilute H2S04 or HCl; finally gold and silver with thiourea in dilute HCl.

Jan 1, 1988

By E. vanHuyssteen

A method of establishing the relationship between the mineralogy of a sinter and its subsequent processing behaviour in a lead blast furnace is demonstrated. It involves: 1) analyzing the Zn-spinels, hardystonite, larsenite, Pb-silicates, Pb-arsenates, Pb-(Ca)-sulphates and other femtes with an electron microprobe; 2) determining the extent of elemental substitutions in various mineral structures; 3) establishing a sequence in which the various phases formed during sintering. In this manner the relationship between the bulk chemistry of a sinter formulation and the speciation of elements into various phases in the sinter can be established. Specifically, the-substitution of Mg for Zn in hardystonite significantly influences sinter production. Mg substitution releases Zn into the surrounding matrix. This Zn reacts with the Pb-silicate to form larsenite thereby reducing the amount of Pb-silicate available for anhydrite digestion. Excessive amounts of residual anhydrite thus result if the sinter formulation is based solely on the CaO/Si& ratio.

Jan 1, 1993

By Dong Hoon Han

The simultaneous sulfation by sulhr dioxide and oxygen of CaO and MgO in calcined CMA (calcium magnesium acetate) were investigated. he experiments were carried out in the temperature range from 700 to 830 "C and at the SO2 concentrations of 0.3 to 1 mol %. The oxygen concentration was kept at 5 %. Each sample was calcined completely before the temperature was lowered to the sulfation temperature. According to the ranges of partial pressure of sulhr dioxide and temperature, there exist three regions for the sulfation reaction: region I in which neither oxide is sulfated, region I1 in which only CaO is sulfated, and region 111 in which both oxides are sulfated. It was shown that the MgO in calcined CMA is sulfated at a rate comparable to that of CaO by forming a mixed sulfate phase. Thus, unlike MgO contained in other desulhrization materials, the MgO content in calcined CMA can be fully utilized for flue gas desulhrization.

Jan 1, 1999

By J. P. Evans

The modem copper smelter today utilizes tonnage oxygen for smelting concentrates, generating a high strength S02 off-gas leaving the smelter vessel. This gas stream, which also contains any unreacted oxygen, plus C02, N2 and H20, also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates. The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals in the off-gas circuit. Depending on this history, the type and characteristics of the chemical and physical reactions which. occur in the gas handling system can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries .and design, on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data, several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating improved technology for mineral flotation. A variable often neglected in flotation control is redox potential. The use of redox control is illustrated by the separation of molybdenite from chalcopyrite. Laboratory testing showed that redox potential had a greater effect on product quality than collector addition. A significant need in froth flotation is greater reliability of the sensors used in measuring and controlling redox potential in mineral slurries. The USBM has developed an automated method for removing scale and reconditioning gold redox-sensing electrodes. Fouled electrodes are anodically polarized to 1.2 V versus the AglAgCI reference potential to remove scale. The electrodes then are conditioned by a brief potentiodynamic treatment to re-establish electrochemical equilibrium. In laboratory tests, this technique removed calcarious deposits from gold electrodes and reconditioned them for useful service in approximately 10 min. In plant practice, this technique would obviate the need for plant operators to manually polish electrodes, and also should result in greater reliability in redox measurements. Inexpensive, automated equipment to condition electrodes in a plant setting is described.

Jan 1, 1995

By Lu Lin, Yan-ping Bao, Min Wang

In order to forecast the cost of dephosphorization during BOF process, and achieve economical dephosphorization of BOF. The mathematical model of dephosphorization cost for BOF process was established. The model calculations show that, when the silicon content and phosphorus content are increased in hot metal, and the final phosphorus content of BOF is decreased, the dephosphorization cost will be increased. The silicon content of hot metal is increased of 0.1% in the plant, the dephosphorization cost is added by 9 RMB/ton steel. The De-P cost of mode A is much higher than the other two modes for three typical production modes of single slag melting process, when the phosphorus content of hot metal is higher than 0.14%, an increase in the phosphorus content by 0.01%, the De-P cost of mode A is added by about 7 RMB/ton steel. Meanwhile, when the phosphorus content of hot metal is lower than 0.165%, the De-P cost of mode C is higher than mode B’s. For BOF single slag melting process, the dephosphorization cost calculated by model is between ± 2%, proving that the model is reliable for the prediction of dephosphorization cost.

Jan 1, 2015

By R. F. Hammen

Copper is one of the most widely used metals in industrial processes and is also present in most mining operations. Extraction of copper from solutions often proves difficult due to the presence of complexing agents. ChromatoChem, Inc. has developed a Solid Phase Extraction (SPE) support (HiPAC) for removal and recovery of metals from wastewater. The HiPAC SPE support employs chelating agents covalently coupled to a long linker molecule. Several solutions containing copper and complexing agents were tested including 1) copper and carbonate, pH 9.8, 2) mixed metals and anions with copper and cyanide, pH 11, and 3) copper and the chelating agent EDTA, pH 11. The copper was extracted from solutions one and two at high pH, but the EDTA containing solution needed the pH lowered to make the copper available for capture. In each example, the copper concentration was significantly reduced by HiPAC SPE treatment.

Jan 1, 1994

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transformation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling

Jan 1, 2003

By N. Choi

The distribution behavior of cobalt, gold, and silver in nickel sulfide smelting was investigated between 1250-1300 °C under inert gas atmosphere. The distribution coefficients of these elements between nickel-copper-iron matte and silica-saturated iron silicate slag were determined as a function of matte and slag compositions. The effect of slag additives such as CaO, MgO, and Al2O3 on the solubility of cobalt, gold, and silver in slag was also investigated. It was observed that the distribution coefficients of these &nor elements were strongly dependent on matte grade. For cobalt and silver, the distribution coefficients decreased as the matte grade increased. However, the distribution coefficients of gold increased as the matte grade increased. The solubility of these minor elements in iron silicate slag was considerably decreased by the addition of basic oxides. Temperature dependence of the distribution of the minor elements will also be discussed.

Jan 1, 1995

By Neal Schwartz, Robert De Saro, Richard Rosenthal, Ed Kear

"A Stack Melter has been installed and is currently operating at Lexington Die Casting. The Stack Melter consists of a 1 meter (3 foot) diameter refractory tube, 2 meters (7 feet) high. Specification ingots are continuously fed to the top of the melter and piled to nearly the top. A burner fires through the scrap which melts the lower portion and preheats the upper portion. As the lower portion is melted, it is drawn out and the upper preheated scrap falls to a lower level where it in tum melts. The molten metal is fed to one of two holding furnaces for eventual delivery to a casting machine.The Stack Melter's energy use is approximately 2900 joules/g (1,250 Btu/lbm), resulting in an overall energy savings of about 58%. This energy savings is brought about primarily because the flue gases preheat the scrap and the flue gas temperature is dropped to well under 528°C (1000°F)."

Jan 1, 2000

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.

By Michael J. Marinigh

"Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable.In converting furnaces which have tuyères such as the Noranda Reactor and the Teniente, Peirce- Smith and Hoboken converters, efficient tuyère line management is critical to optimizing blowing rates, increasing refractory life, and improving safety.This paper will describe recent improvements made to equipment used for tuyère punching, tuyère silencing, tuyère pyrometry and refractory drilling of tuyères and how the proper application of the equipment can lead to operational and safety improvements."

Jan 1, 2009

By R. E. Molnar

A number of flowsheets have been designed and operated, or are currently being considered, to extract copper from leach solutions having much more copper than the 4 g/L levels typically found in heap leach liquors. Dealing with these solutions has required that the envelope for ?normal? copper solvent extraction be pushed beyond the usually considered limits. Others have published information on flowsheets to recover copper from leach liquors containing over 25 g/L copper. Secondary solvent extraction circuits are often required to attain satisfactory overall recoveries. This paper reviews some of the issues faced in three pilot plant circuits that were operated by SGS Lakefield Research to produce cathode copper from solutions containing 8 to 20 g/L Cu. The primary objective was to maximize copper extraction using one solvent extraction circuit. The role of feed acidity and the disposition of impurities such as iron and chloride are considered. The challenges of running short SX piloting campaigns are discussed.

Jan 1, 2003

By Carla Lupi, Mauro Pasquali

"Photographic technology is based on light sensitivity of silver halides that, because of silver properties, are capable of forming photographic images. Photographic laboratories and hospital departments because of digital photographic systems less use this technology today. Nevertheless recovery of silver is still advantageous because environmental problems related to Ag ions danger to biological system. Many processes have been studied to treat silver containing photographic bath: cementation, chemical precipitation and electrowinning. In this work, after preliminary voltammetric tests, a batch electrometallurgical process has been studied to completely deplete the silver containing photographic fixing baths. The effect, of silver concentration in the electrolyte, varying over the range 0,2-1 g/L, bath stirring and current density ranging from 10 to 500 A/m2 on process yield and deposit quality, has been investigated. Introduction Photographic wastes, electronic scrap and spent catalysts constitute the main sources of materials for silver recycling. Among those silver secondary sources, the photographic discharged material could be still important and useful, even if photographic laboratories and hospital departments, because of digital photographic systems, less use photographic technology. Several processes have been developped in order to recover silver used in the field of photography from both photographic solutions and scrap film paper[1-5]. Fixing solutions are very complex baths but, because of silver position in the electromotive series, electrolysis could represent an advantageous method for silver recovery. Electrolysis produces high purity silver without generating new pollutants, while the fixer can be reused: obviously it is necessary to purge off a portion of this solution in order to avoid the excessive build up of other deleterious compounds into solution. A tested recovery method was constituted by the dissolution of silver from X-ray films with concentrated nitric acid. Internal electrolysis and external electrolysis methods were carried out using a steel electrode as cathode and a copper electrode as anode [6]. Silver recovery from photographic chemical solutions has been also performed in a special cell [7]: the solution is supplied to the bottom of a non-agitated cell having a vertically elongated form and including a central anode enclosed by a cathode. An other study discloses the use of an electrolytic cell comprising at least one anodic compartment and one cathodic compartment: the solution is treated in the cathodic compartment and then recycled in the anodic one [8]. A more recent work proposes the use of zirconium cathode for the recovery of silver from photographic fixing solution [9]: studies carried out by cyclic voltammetry showed that about 98% of total Ag can be recovered with an electrical efficiency close to 92%."

Jan 1, 2008

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

By Mari Naess, Jan Erik Olsen, Gabriella Tranell

"Fume, also known as dust, is produced during metal refining. Exposure to fume is damaging to the health of plant operators. A mathematical model has been developed to study the different factors governing the fuming mechanism. It is shown that natural convection is the main driving force of the phenomenon, and that the fuming rate is highly sensitive to the area of the exposed metal surface. A new feature introduced in the modeling concept is the ability to include a gas flux of unconsumed process gas flowing up through the metal surface. This reduces the fuming rate, and should normally not be neglected.IntroductionFormation of fume from the ladle in which metal is refined into its final specifications is an environmental issue of importance for the working environment in the production plant. In layman-term fume is often known as dust. It is formed when metal reacts with oxygen. As an example of a fuming process, we will focus on ladle refining of silicon. Note that many of the principles and conclusions will apply to other metal refining processes. For silicon production, silica fume (S1O2) is produced when silicon metal (Si) reacts with oxygen (O2).Silicon is produced in a submerged arc furnace. The metal is tapped from the furnace into a ladle for refining. The refining is conducted by injecting a mixture of air and pure oxygen at the bottom of the ladle. The oxygen reacts with the metal and the impurities, and the amount of impurities is reduced according to product specification. At the ladle surface, metal also reacts with oxygen present in the air surrounding the ladle. This reaction produces silica fume as illustrated in Figure 1."

Jan 1, 2012

By P. Mercille, M. F. Nasmyth, J. G. Cooper

The turn of the century sees considerable activity in the zinc industry for the replacement or expansion of existing cellhouses, and the building of new cellhouses as part of new zinc projects. Aside from the cellhouse technology itself, numerous engineering and construction issues play a major role in the success of a project for replacing or building new cellhouses. The purpose of this paper is to bring to light and to address the engineering and construction factors which go beyond the selection of a cellhouse technology and which remain of key importance in implementing such projects. In addition, some implications of these factors for project costs will be illustrated.

Jan 1, 2000

By Graham Cooke, Abhishek Lahiri, Animesh Jha, E. Jeya Kumari

"CO2 reduction by alternative energy devices such as wind-power, electric vehicles utilize rare-earth elements (REE) in several forms; such as in piezo-electric devices, batteries and magnetic materials. In 2010, the 95% of Rare Earth supply is controlled by China, compared to USA being dominant supplier in the 1980s. The dependence upon a single source of lanthanides has prompted the utilization of lower grades of titaniferous mineral concentrates, which often have rich seams of REE. We propose a new methodology, which utilizes the low-grade minerals for the extraction of synthetic rutile and also significant quantities of REE. We demonstrate the alkali roasting of lower grades of mineral concentrates and subsequent leaching in an aqueous medium for preferential flocculation of REE during the extraction of synthetic rutile. Changes in mineral structure during alkali roasting and leaching determine flocculation of REE and permit their separation at the front end of unit process.The physical chemistry and crystal structure of minerals in equilibrium with alkali and aqueous medium play an important role, which we explain by demonstrating the changes in the crystal structure. The quantification of separation of RE oxide via chemical analysis suggests that it may be possible to separate rare-earth oxides between 50 and 80% of the initial concentration in the non-magnetic fractions of ilmenite, for example. The microstructural and X-ray diffraction analysis points out that the presence of alumina and roasting with potassium based alkali enhances the separation and flocculation of rare-earth elements at the front end of the process after roasting. The process allows the recovery of CO2 generated by recycling into the process for the regeneration of alkali."

Jan 1, 2011