Search Documents

By R. M. Santmyers

Of the sand and miscellaneous silica produced in the United States , ordinary sand and gravel are , of course , the most important, at least as regards volume of output . The building- construction industry absorbs approximately 75 per cent of the total value of all quartz and silica , as shown in Table 2 of Quartz and Silica, Part I, under "General summary . " Because of their unusual physical properties tripoli and diatomite find extremely wide uses in industry, and as the commercial deposits of these ninerals , especially tripoli , are scattered, large quantities enter into interstate commerce . Whereas ordinary sand and gravel are bulky commodities , these specialties have a fairly high unit value and hence can be transported relatively long distances .

Aug 1, 1931

By Alexandre de Freitas Gomes de Mendonça

O pick-up de nitrogênio no aço deve ser evitado nos processos de fabricação em uma Aciaria de alto desempenho. Entretanto, o pick-up de nitrogênio pode ocorrer em inúmeros pontos na Aciaria, principalmente quando o aço líquido é exposto ao ar atmosférico. Alguns locais de controle têm grande relevância no resultado do pickup, tais como: durante o vazamento do aço do convertedor para a panela, no refino secundário durante a agitação excessiva do aço e no lingotamento contínuo devido a aspiração de ar atmosférico nas conexões. Neste trabalho, o foco do controle da incorporação de nitrogênio é no lingotamento contínuo e, para efeito de estudo, tomou-se como referência um pick-up de nitrogênio de até 5 ppm. Os dados históricos mostram que menos de 64,6% das corridas encontravam-se com pick-up de nitrogênio abaixo de 5 ppm. Assim, visando reduzir esse pick-up foi proposto um ajuste no ângulo da sede da válvula longa, melhoria do projeto do gasket e capacitação da equipe de operação. Após a efetivação dessas ações de controle esse número passou para 97,7% das corridas lingotadas.

Jul 30, 2018

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

[ ]

Jan 1, 1981

By Sutham Niyomwas

Silicon-Silicon Carbide (Si-SiC) composites were synthesized by self-propagating high temperature synthesis (SHS) from a powder mixture of SiO2-C-Mg. The reaction was carried out in a SHS reactor under static argon gas at a pressure of 0.5 MPa. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of silica sources and carbon mole ratio in precursor mixture on the Si-SiC conversion were investigated using X-ray diffraction and scanning electron microscope technique. The as-synthesized products of Si-SiC-MgO powders were leached with 0.1M HCl acid solution to obtain the Si-SiC composite powders.

Jan 1, 2009

By Alexander B. Reeb, Richard J. Varuso, George M. Filz, Jehu B. Johnson

"T-walls, which are concrete floodwalls in an inverted “T” shape, are an integral component of the Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS). In order to resist large lateral flood loads, T-walls are typically supported on long batter piles that extend through the weak and compressible clays and peats commonly encountered in southern Louisiana. Since the piles are battered, settlement of the compressible foundation soils can result in loads acting normal to the piles and induce pile bending moments. Therefore, the design of pile-supported T-walls is a complex soil-structure interaction problem that requires detailed and careful numerical analysis to accurately estimate the stresses and bending moments in the piles. For this paper, numerical analyses were performed for three cross sections that each included a two-pile T wall system that was installed within a 15-ft tall new levee embankment. The cross sections were identical except that the elevation of the T-wall base was varied. This paper discusses the analyses, and it compares the influence of settlements and flood loading on the pile stresses and bending moments. In addition, this paper includes general recommendations for the analysis and design of pile-supported T-walls in practice.INTRODUCTION AND BACKGROUNDThe recently completed Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS) includes 350 miles of levees and floodwalls and is designed to defend against a 100-year storm surge event. The floodwalls predominantly consist of I-walls and T-walls. I-walls are comprised of a sheet pile wall curtain capped with a monolithic concrete wall above grade. T-walls are similar to I-walls, but they include a wide concrete base at grade, which forms an inverted “T” shape, and they are generally supported by long batter piles that provide additional lateral and rotational stability for resisting flood loads.During Hurricane Katrina, several I-walls failed, resulting in large breaches and devastating flooding (Duncan et al. 2008, IPET 2009). T-walls on the other hand performed quite well, including T-walls that were overtopped and eroded on the protected side, yet still did not collapse. As part of the HSDRSS, more conservative designs and height restrictions were required for I-walls (USACE 2011), and a number of I-wall sections were replaced with T-walls. However, the design of pile-supported T-walls is complex and requires careful consideration of both flood loading and settlements."

Jan 1, 2017

By M. Hokkanen, M. Hagfors

The Finnish Defence Forces has destroyed old and spoilt munitions in open surface mass detonations at Hukkakero fell in municipality of Kittilä, Lapland, since 1988. The technique was learned from Sweden. The destruction camp is organized every year at autumn and it lasts 4-5 weeks. During the disposal period one or two charges are exploded per day. The gross weight of a typical charge varies from 150-250 tons including 15-25 tons of explosives. They mainly consist of TNT, but may also contain smaller amounts of amatol and hexotol. As a booster there have been used 2-3 tons of emulsion explosives.

Jan 1, 2015

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By Chuanfu Zhang, Liwei Liang, Yanxin Wu, Jinliang Wang

"According to the reaction shaft operation characteristics during the flash smelting process, 15 groups of slag samples containing high Fe3O4 were prepared by some chemical reagents, and then the slag viscosities were measured using a RTW-10 type synthetic test instrument for melt physical property by the rotating cylinder method. The effects of Fe/SiO2 ratio (mFe/mSiO2), Fe3O4 content (wFe3O4), Cu2o), MgO content (WMgO) and Cao content (wCaO) on the slag viscosity were also studied. Results show that slag viscosity is decreased with the increase of temperature, mFe/mSiO2, wCu2o, wMgO and wCao, and with the decrease of wFe3O4, under the range of slag contents: mFe/mSiO2 1.36~1.78, wFe3O4 17.83%~21.18%, wCu2o 3.51%~8.34%m wNgI 2.21%~6.57%m w/caI 6.22%~9.387% and temperature range if 1250 o/c~1450 oC. Only wFe3O4m and w/caO have great influence on the slag viscosity when temperatures as high as 1400 oC. Only wFe3O4 and wCaO have great influence on the slag viscosity when temperatures as high as 1400 oC or so. To form a freeze slag with higher viscosity inside the reaction shaft, wFe3O4 should be more than 20% and wCaO should be less then 6%.IntroductionSince its appearance in 1949, Outokumpu flash smelting technology has making continuous innovation and has become the most competitive intensified smelting technology [1], widely considered to be the standard clean smelting process [2]. At present, flash smelting technology is adopted to newly build or reconstruct most of the world's copper or nickel smelting enterprise [3]. Reaction shaft is the most important part of the flash smelting furnace. During the flash smelting process, reaction shaft must be able to withstand the following harsh conditions at the same time: 1) high temperature varying from 1400 °C to 1500 °C. 2) strong oxidative atmosphere containing 50% - 80% oxygen. 3) solid particles and melt with speed up to l00 m/s. 4) high acidic or basic slag with strong chemical corrosiveness. 5) smelting gas containing 50% - 80% SO2. 6) matte with strong dissolution."

Jan 1, 2012

By Peter Wells, Gordon Marrs, Dominic Fragomeni, Warren Holmes, Daryl Macnamara

"LocationThe Strathcona mill ofFalconbridge Limited is located in Onaping, Ontario, 50 km northwest of Sudbury.GeneralOre from the Falconbridge mines in the Sudbury Basin (Strathcona, Fraser, Onaping, Craig and Thayer Lindsley mines) is processed through the Strathcona mill with 8500 t of nickel ore and 1500 t of copper ore being treated daily. Current capacity is -3 Mt of ore at 1.8% Ni, 1.9% Cu combined grade. Custom feeds are also processed. The valuable minerals in the ore are pentlandite (FeNi)9S8, chalcopyrite (CuFeS2) with some cubanite (CuFe2S3) and very minor nickel sulphides/ arsenides. Cobalt is present mainly in solid solution in pentlandite. There are small but economically important concentrations of precious metals including platinum, palladium gold, and silver. The common non-sulphide gangue minerals are feldspar, quartz, mica, talc, and chlorite while pyrrhotite (Fe7S8) is the major gangue sulphide. The pyrrhotite contains between 0.6% and 1.2% nickel in solid solution and additional nickel as exsolved pentlandite in micron sized blebs. The nickel and copper ores are batch-crushed in a two stage dry crushing plant and then ground in separate circuits. Concentration by flotation and magnetic separation produces a nickel concentrate assaying approximately 16% nickel plus copper and a copper concentrate assaying 30% copper and 0.4% nickel. The nickel concentrate is trucked as a slurry to the Falconbridge smelter while the copper concentrate is trucked as filter cake to the Kidd Division of Falcon bridge"

Jan 1, 2000

By L. K. Marshall

The importance of high quality underground mine ventilation is readily apparent. The principles of primary and auxiliary mine ventilation, however, are sometimes less readily apparent. The first article in this two-part series discusses some general aspects of primary and auxiliary ventilation. Next month's article will detail considerations involved with auxiliary mine ventilation.

Jan 1, 1982

By Charles G. Maier

SCIENCE beginning in rational observation came of age, when its devotees first began to measure and count. It has been said that the most striking aspect, of science today is its growing abstraction, and its preoccupation with mathematical symbolism. Technology with specific and concrete objectives in the satisfaction of human wants, cannot conceivably achieve the abstract unification that science seeks, but .the utility of the' scientist's method has been too well proved to require bolstering. Metallurgy is in its scientific infancy.

Jan 1, 1931

By Louis R. Iverson

Analysis of seed numbers present in topsoils (a grazed area, an ungrazed area, and two stockpiles) indicated that seeds of the most prevalent colonizers (e.g., Kochia scoparla, Setaria virdis, and Salsolo collins) were not present in the topsoil upon respreading but rather appeared by immigration from the surrounding areas. The grazed site had a seed density of over 7,700 seeds m-2 (of which 43% were from weedy species) and the ungrazed site had 3,900 seeds m-2 (of which 7% were weeds); the stockpiled topsoils had very low seed densities (255 and 520 seeds m-2). Seed densities and diversity decreased with depth on both the grazed and ungrazed sites; this was especially true on the grazed site where 94% of the seeds were found in the surface 7.5 cm. Several species were present in the seed bank (e.g., Hedeoma hispida, Artemesia ludoviciana, A. frigida, and A, abslnthlum) which were also found on the three and four year old mined sites in the aboveground vegetation survey. Seeds from these species may germinate after several years of dormancy, thereby starting populations on mined sites and enhancing plant diversity. Seed bank analysis was also undertaken on mined sites ranging in age of 2 to 6 years (plus an unmined site). Mined site seed densities ranged from 1630 to 3980 seeds m-2, with the four year old site having the greatest density (largely because of high Melilotus spp. populations); unmined site and stockpiled topsoil sample had lower seed densities. A significant positive correlation between total viable seed content and soil-water saturation percentage indicated that soil texture may influence seed viability/ dormancy (the. finer the material, the higher the seed population). As with the previous part of this study (and other studies), there was a poor correlation between the aboveground flora and the belowground seed composition.

Jan 1, 1982

By J. Cole

The Morenci concentrate leach plant construction was completed and successfully commissioned in October 2007. The plant was designed to operate at medium temperature, 160ºC and pressure, 2,100 kPa. The concentrate leach plant utilized many innovative design features. This paper examines the first year?s operation, the challenges, the successes and the lessons learned. The future plans for Morenci concentrate leaching will also be presented.

Jan 1, 2009

By Daniel W. Kappes

Testing ores for heap leach operations traditionally follows a progression of bottle roll tests, bucket and column leach tests, and very expensive large field leach tests. Enough data is now available to streamline the procedures. Data from five different operations shows that recoveries from large field leach tests can be predicted from the bucket tests. Initial recovery times in large field leaches are longer than in bucket tests- a typical response is eight days versus twenty days to the same recovery percentage; but the ultimate percent recoveries (after 60 days) are normally very close. Methods of mining and stacking can radically affect recoveries from clay-rich ores. Leaching of uncrushed ores provides special testing problems, since accurate samples smaller than several tons cannot be taken.

Jan 1, 1981

By M. Yekich, W. R. Reed, G. Ross, A. Salem

"Canopy air curtain (CAC) technology has been developed by the National Institute for Occupational Safety and Health (NIOSH) for use on continuous miners and subsequently roof bolting machines in underground coal mines to protect operators of these machines from overexposure to respirator coal mine dust. The next logical progression is to develop a CAC for shuttle cars to protect operators from the same overexposures. NIOSH awarded a contract to Marshall University and J.H. Fletcher to develop the shuttle car CAC. NIOSH conducted laboratory testing to determine the dust control efficiency of the shuttle car CAC. Testing was conducted on two different cab configurations: a center drive similar to that on a Joy 10SC32AA cab model and an end drive similar to that on a Joy 10SC32AB cab model. Three different ventilation velocities were tested—0.61, 2.0, 4.3 m/s (120, 400, and 850 fpm). The lowest, 0.61 m/s (120 fpm), represented the ventilation velocity encountered during loading by the continuous miner, while the 4.3 m/s (850 fpm) velocity represented ventilation velocity airflow over the shuttle car while tramming against ventilation airflow. Test results showed an average of the dust control efficiencies ranging from 74–83% for 0.61 m/s (120 fpm), 39–43% for 2.0 m/s (400 fpm), and 6–16% for 4.3 m/s (850 fpm). Minor modifications to the shuttle car CAC design and placement improved the dust control efficiency to 51–55% for 4.3 m/s (850 fpm) with minimal impact on dust control efficiencies for lower ventilation velocities. These laboratory tests demonstrate that the newly developed shuttle car CAC has the potential to successfully protect shuttle car operators from coal mine respirable dust overexposures. INTRODUCTION The development of the canopy air curtain (CAC) dates back to the 1970s starting with the initial development of the CAC by the Donaldson Company, Inc. under contract from the U.S. Bureau of Mines [Krisko 1975]. This CAC was originally developed for continuous miner operators when continuous mining machines had cabs. The need for a CAC on the continuous miner was eliminated when the cab was removed from the machine design. However, CAC development progressed to include CAC designs for a roof bolting machine to protect roof bolters from respirable coal mine dust [Goodman and Organiscak 2002, Listak and Beck 2012, Reed et al. 2017]. This roof bolting machine CAC research continues to the present day."

Jan 1, 2018

By Lucas Sanches Magalhães

A utilização de resíduos industriais é dificultada, na maioria das vezes, pela presença de determinados elementos, como por exemplo, o ferro, justificando assim a sua remoção. Dentro deste contexto, o objetivo deste trabalho foi estudar a sulfatação de um resíduo proveniente da flotação de um minério de ferro e subsequente lixiviação deste resíduo sulfatado. A composição mineralógica da amostra inicial foi obtida por DRX e MEV sendo possível identificar quartzo (SiO2), hematita (Fe2O3) e muscovita (KAl2Si3AlO10(OH,F)2). De acordo com a análise química, os teores dos elementos principais foram: Fe (12,65%), S (4,02%), e Al (0,62%). Na sulfatação, realizada à 250ºC durante 4 horas, foi estudada a influência da relação ácido sulfúrico/amostra (0,1:1; 0,2:1; 0,7:1; 0,8:1; 0,9:1 e 1:1) na extração do ferro. A lixiviação foi conduzida com 5% de sólidos do material sulfatado, sendo avaliada a interferência da temperatura de lixiviação (25°C e 90°C) e do tempo de duração dos ensaios (15min, 30min, 60min, 120min, 180min e 240min). Pelos resultados obtidos observou-se que o tempo de lixiviação foi um parâmetro insignificante. A máxima extração de ferro foi encontrada sulfatando o resíduo na relação ácido/amostra 1:1 e posteriormente realizando a lixiviação deste resíduo sulfatado a 90°C por 30 minutos, alcançando 85,64% de extração do Fe.

Aug 17, 2017

By H G. Bosmare, G Bedser, C V. B Cunningham

Peak Quany has achieved substantial improvements to its bottom lie by giving close attention to blasting practice, and in pr@icnlar by introducing electronic delay detonators for routine production blasting. The precision and flexibility provided by these units has enabled the quarry to gain control over fmes and curtail oversize without increasing explosive usage. In addition, the extent of nuisance from blasting vibrations has been reduced.

Jan 1, 1998

By Art Carino

"The McClean Lake operation is located in the Eastern Shore of the Athabasca Basin in northern Saskatchewan some 700-air kilometers north of Saskatoon. It is operated by Cogema Resources Inc., the major share holder of the joint venture consisting of Cogema Resources Inc., Denison Mines Limited and OURD, a consortium of Japanese utilities.The JEB mill is the first uranium mill to be constructed and licensed in North America within the last 15 years. The mill uses conventional uranium unit process but employs innovative techniques unique to the JEB mill.This paper presents brief descriptions of the various unit processes, the innovations and the commissioning strategies developed to achieve the designed production capacity in the shortest possible time.INTRODUCTIONThe McClean Lake ore body was discovered in 1979, followed by the discovery of the JEB ore body in 1982. From 1985 to 1990, a cluster of deposits named Sue A, Sue B and Sue C were discovered. Environmental Impact Assessment (EIS) of the McClean Lake project began in 1990 under a joint federal-provincial process. Following the public hearings in 1993, the governments gave approval to proceed with the construction of the project, subject to fulfilling licensing requirements.The McClean Lake ores are located in the uranium-rich geological region of Saskatchewan known as the Athabasca Basin, 700 air kilometers north of Saskatoon. The JEB mill is located near the mined out JEB open pit that is now used as the tailing depository.The approved mill has a production capacity of 6,000,000 pounds of U3O8 annually and is capable and licensed to process JEB, Sue A, Sue B, Sue C, McClean Lake, and Midwest Lake deposits. Although the EIS has been approved, Mining of the Midwest Lake deposit has not been approved at this time."

Jan 1, 2001

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994