Search Documents

By R. B. McElwaine

From November 1943 to April 1944, the Bureau of Mines put down 18 churn-drill holes aggregating 2,571 feet of bore in an investigation of the virtually abandoned zinc deposits of the north-central Arkansas district, principally in Marion, Boone, Searcy, and Newton Counties. The ore of this area occurs in flat-lying sedimentaries of the Mississippian and Ordovician ages. Much of the zinc is in the form of carbonate and silicate, although some sulfide has been produced. Preliminary studies resulted in selection for investigation of the Big Hurricane mine in northwest Searcy County, the Spies mine in northeast Newton County, and the Coon Hollow mine in eastern Boone County The comparatively large production of th.ese properties in the past was a factor in the selection. This report describes the work accomplished in the investigation and presents the data obtained.

Jan 1, 1948

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By C. A. Young, J. D. Miller

Thermodynamic data has been obtained for oleate chemisorption at fluorite (CaF2) and calcite (CaCO3) surfaces using adsorption isotherms determined previously at room and elevated temperatures by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS). Linear regression analysis was used to statistically derive free energy data as a function of temperature assuming oleate chemisorption followed Langmuir-type adsorption. Enthalpy and entropy changes were subsequently ascertained from the Clausius-Clapeyron equation and fundamental thermodynamic relationships. Essentially, no difference in the free energy of chemisorption at the two mineral surfaces was found; however, the differences in enthalpy and entropy values were significant. By comparison, the results showed that oleate chemisorption at fluorite surfaces was more extensive and more entropically driven due to more water being displaced. Results correlate well with values determined in the literature for other mineral collector systems. These findings help explain the greater hydrophobic character of fluorite than calcite in both the absence and presence of oleate.

Jan 1, 2002

By Colin Hardie, Simon Pelletier, Rakan Rhabani, Guy Comeau

"In order to improve the nickel concentrate thickener operation at Raglan Mine, two pulp deaeration cyclones were installed. These units obtained from Outotec Pty Ltd, also called the FrothBuster®, have been in continuous operation since mid-October 2006. The primary objective of the de-aeration cyclones is to lower the solids content in the thickener overflow by de-aerating the concentrate pulp before it enters the concentrate thickener. This dearated slurry should help decrease the nickel particle losses that report to the thickener overflow because of the flotation effect within the thickener.Optimizing the de-aeration cyclones has been a slow and ongoing process, however, initial testing is encouraging. The latest test results indicate a 50 % reduction (0.070 to 0.035 % solids) in nickel losses to the concentrate thickener overflow resulting in an additional $350,000 in annual revenues.This paper will present an overview of installing the de-aeration cyclones within a limited space, as well as the preliminary commissioning and testing challenges. This paper will also discuss the most recent concentrate thickener operating results since the de-aeration units were installed.INTRODUCTIONThe Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik Region has been in production since 1997. In early 2002, the concentrator implemented the Zero Process Water Discharge (ZPWD) project to recycle the process water to decrease fresh water consumption and reduce discharges to the environment. Due to this initiative, the chemistry of the process water changed significantly resulting in flotation concentrate streams, which were very frothy and difficult to manage. This phenomenon has resulted in operational challenges in many areas of the concentrator including slurry pumping, flow measurement and concentrate thickening.In October 2005, the Raglan Mine underwent a conversion from an AG mill to a SAG mill operation in order to increase throughput and to optimize key process areas. As part of this project, the first two North American pulp de-aeration (FrothBuster®) units from Outotec were installed to improve the operation of the concentrate thickener. The primary objective of the deaeration technology was to lower the solids content in the thickener overflow by de-aerating the concentrate thickener feed pulp. This in turn was to reduce the froth, which accumulates on the thickener surface, and more importantly reduce valuable nickel losses to the thickener overflow because of the flotation effect within the thickener."

Jan 1, 2008

By T Wootton

The Barrytown ilmenite pilot plant was commissioned in two stages using Westport Titanium Project heavy mineral concentrate. The wet concentrator was commissioned on the 17 December 1989 and produced magnetic concentrate from this date.   The Drymill was commissioned on the 27 January 1990 and produced product grade ilmenite successfully from the onset.   The commissioning period was exceptionally short by normal standards and few problems were encountered. This paper concludes with general observations of operations of the pilot plant.

Jan 1, 1990

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

Instabilities occurred as a result of climate changes caused to investigate the rock behavior dependency to temperature changes, in this paper. In the natural earth condition, the phase transition of pore water has known to be the most effective factor causing different rocks mechanical properties due to temperature changes. So, the temperature range of [-30, 30]°C is selected in laboratory tests of this study. P-wave velocity, unconfined compressive strength (UCS) and elasticity modulus of rocks at different temperatures are studied by developing a temperature adjusting apparatus. The tests were performed on three rock types. The results show that firstly, the temperature reduction and pore fluid freezing improves these rock?s mechanical properties. Secondly, the dependency of rock properties to climate changes depends on the type and shape of its porosity as well as porosity percent. The improvement of rock mechanical properties in jointed rocks exceeds rocks with spherical pores. Finally, maximum changes in rock?s properties occur at [-10, 0]°C, which includes the phase transition of pore fluid. Keywords: Temperature; Rock Mechanical Properties; Pore Fluid; Porosity.

Feb 27, 2013

By R A. Binns, S Murao

The PACMANUS and Jade deposits are two active hydrothermal fields that are forming massive sulphide deposits at the Pacific rim margin. Both are associated with felsic submarine volcanic rocks and both occur in back-arc settings. However, PACMANUS is associated with almost sediment-free dacites and lies on the crest of a volcanic ridge, whereas Jade occurs in a heavily-sedimented tectonic depression associated with a basement of pumiceous rhyolite. The PACMANUS deposit is richer in Cu and Au, and Jade in Pb. Zinc, Ag, As and Sb contents are similar. Sulfide textures at PACMANUS suggest formation of Cu and Zn sulfides by simultaneous double-diffusion involving inwards-moving seawater mixing with outwards-moving hydrothermal fluid. By contrast, at Jade there is a more complex history of formation where initial growth of barite on the sediment surface, probably associated with microbial activity, formed an impervious cap which trapped higher temperature hydrothermal solutions.  

Jan 1, 1995

By D. J. Farmer

Mining hoists are major components of any underground mine, however, the detailed design work required to get the actual power required for a particular hoist is outside the scope of preliminary feasibility studies. Nonetheless, a hoist is costly. Therefore, an accurate estimate is needed for the design parameters and the power required. There are two methods available, namely, the O’Hara method and the Society of Mining Engineers’ method. Tests were done for both methods employing nine friction hoists and 19 drum hoists currently in use at Canadian mines. The O’Hara method provided unacceptable results for both friction and drum hoists. While, the SME method was designed for American regulations and factors of safety which often differ significantly from Canadian ones, good results were obtained. The two relationships deter-mined were simply to add 5% to friction hoist design and to add 4% to drum hoist design. Modifying the SME method by these two factors will allow the hoisting system determined by the SME method to be within the error for a prefeasibility study.

Jan 1, 1997

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module (Fig. 1). The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information. Key for Fig. 1 A-Helium-3 neutron detector B-Wax moderator for neutrons C-Irradiation chamber D-Funnel for receiving ore E-Gate F-Transducers G-Biological shield for neutron source H-Transfer tube for neutron source I-Neutron source J- Microprocessor K-Accumulator for hydraulics L-Control panel M-Electro-hydraulic servo valve to control movement of the source N-Electro-hydraulic proportional valve to control movement of the gate O-Hydraulic power unit Irradiation and Counting Equipment Irradiation of the ore is achieved using a 1 X 10 7 neutron*s-1 californium-252 neutron source. The source is contained in an iron capsule and pneumatically transferred between the irradiation/counting and storage chambers. The irradiation/counting chamber possesses 12, 600-mm (24-in.) long helium-3 thermal neutron detectors embedded in an annulus of wax (Fig. 1). Two sets of six detectors are each interfaced to a preamplifier, amplifier and single-channel pulseheight analyzer system, and the two systems are connected to a scaler. A special timing unit controls the transfer of the source and the on and off switching of the detector assembly, in sequence with the movement of the source. Results and Discussion In the experimental demonstration, using the 107 neutron.s-1 source, a 10% uranium ore was measured to ± 10% (2o total error) in 10 cycles and ±6% (2o) in 100 cycles. Since a larger source was not available, it can be statistically predicted that a 109 neutron-s-1 source could be used to measure a 0.1% ore to ± 10% (20) in 10 cycles. The uranium can occur as discrete nonhomogeneous particles in the ore, and the error caused by such a distribution of particles is ± 4% (2o), as determined by

Jan 1, 1984

By Robert B. Hopler

Explosives, originally used only in fireworks and warfare, became legitimate contributors to human progress when miners in Eastern Europe began using them to break rock in the early 1600%. Since that time these powerful materials have had a dual role in the world: as agents of destruction in war, and as irreplaceable tools necessary to advance civilization. In the latter role, they serve as agents to enable mankind to produce metals, build roads, and drive tunnels. In other words, to provide those materials, services, and infrastructure without which the modern world could not exist.

Jan 1, 1997

By Larry A. Lass

The U.S. Bureau of Mines, in cooperation with the Iron Range Resources and Rehabilitation Board, investigated the potential of using northeastern Minnesota papermill waste sludges as a binder for Mesabi Range iron ore (taconite) concentrate. Sludges from five different commercial papermill waste treatment operations were evaluated in laboratory tests. Except for the coarsest sludge, all were fairly easy to blend with the taconite concentrate using conventional mixing methods. The coarsest sludge had to be reslurried at 2 pct solids before adding it to the concentrate in order to obtain pellets without visible sludge clumps. Drying and grinding the sludges made them less effective as binders because of a lower degree of rehydration. On a dry weight equivalent basis, twice as much raw sludge binder was required to obtain similar pellet physical properties as with bentonite; however, the pellets made with raw sludge had superior metallurgical properties. Over 30 pct higher reduction rates and over 1500 C higher softening temperatures were obtained with sludge binder than with bentonite. Sludge D, which had the lowest fiber and the highest alkali metal content, resulted in the lowest reducibility enhancement. Even though more raw sludge was required than bentonite, the sludges have virtually no value, and therefore may provide a cost-effective additive binder for producing improved metallurgical-quality pellets. Large-scale testing has not been done to confirm these laboratory results.

Jan 1, 1989

A description is given of a simple, cheap device that enables the intact shear strength of rock to be determined quickly and inexpensively. Thin rock plates, prepared with a diamond saw, are tested in double shear by a linear punching action. By varying the direction of the diamond-saw cut in a number of specimens, the change in shear strength can be measured for different orientations relative to the rock fabric.

Jan 1, 1980

By Sushil Bhandari, S. S. Rathore

Controlled drilling and blasting continue to be an important method of block production and for block splitting. Drill and blast technique has disadvantage that sometimes, it produces cracks in uncontrolled manner and also produces micro cracks in the block as well as in remaining rock, if not carefully carried out. Recovery by this method is low compared to other methods. Therefore, attempts have continued to develop controlled growth of crack in desired direction. In this paper a series of tests are described using detonating fuse in marble. Economics of different methods is also compared. In comparison to conventional use when holes are lined with inexpensive cardboard or plastic liners with a slit, the cost and damage is the least and development of crack is in desired direction.

Jan 1, 2002

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By I. V. Lunkin, E. B. Rakishev, B. R. Rakishev

In mining the method of statistical tests is used by solving of problems, exposing to influence of random factors. Such problems are: rational selection of equipment set; co-ordination in time of different processes; interaction between some processes and kinds of works. Usually it is considered that Monte Carlo method proves its value in the first place in that problems, which allow theoretical-probabilistic description. Analysis of numerical solution of mining-economic problems shows that the method of statistical tests may be used successfully by solving of determinate problems, which are solved usually analytically or by the methods of mathematical programming. We are talking about the problems of optimal use of resources, expedient placing of equipment, effective use of investments, rational planning of stripping and extracting works, groups of mining enterprises and about different variants of transport problem. In the report possibility of the method use is studied at an example of typical technical-economic problems solving. By solving of these problems the variant of the method with uniform distribution of random quantity had been applied and built-in random number generator of visual modelling system VisSim had been used. By algorithms elaboration it seems very perspective to use combination of the Monte Carlo method with traditional methods of numerical solving of the problems (methods of linear, nonlinear and dynamic programming and so on). Keywords: method of statistical tests, mining-technical problems, diapason of random number sample, efficiency function and its extremum.

Jan 1, 2003

By W. C. Kelly, E. J. Essene, A. M. Affifi

Occurrences and associations of natural tellurides are constrained by the relative fugacities of Te, in specific mineralizing environments. Some are rare (e.g., FeTe2) and others absent (e.g. MoTe , ZnTe) m nature because high f-Te2/f-S2 ratios are rare or unattainable , whereas others (e. g . , Ag2Te,HgTe) require lower ratios and are common. Complex and seemingly chaotic sulfide-telluride associations are, in fact, highly systematic and depend both on temperature and fugacity ratios. Some older sulfides act as buffers via reactions such as PbS + Te2 = PbTe + S2, thereby affecting the deposition and paragenesis of younger tellurides and the combined or uncombined mode of occurrence of precious metals. Thermochemical calculations of telluride-sulfide-oxide equilibria can have pragmatic value. The thermochemical approach tells us little about the Te "source", but is beginning to unravel the systematics of telluride mineralogy and controls at the precipitational end of the line.

Jan 1, 1985

By Bob Rautenberg

The Construction of Tunnel and Edison Force Mains contract involves the installation of two new force mains to provide a redundant means for sewage conveyance from Middlesex County Utility Authority?s (MCUA) Edison Pump Station on the northern shore of the Raritan River to the Central Wastewater Treatment Plant on the southern shore. The force mains will be installed in a 1,192 m (3,910 lineal foot) long tunnel with a 4.09 m (13'-5') inside diameter, fully gasketed precast concrete segmental lining, which is to be tunneled underneath the Raritan River utilizing an Earth Pressure Balance TBM. The tunnel is anticipated to encounter flowing soils near and beneath the river. Two new 60-inch diameter Centrifugal Cast Fiberglass Reinforced Polymer Mortar force mains will be installed within the tunnel leaving an open utility corridor above the force mains for future consideration. The project also includes the design and construction of two slurry wall shafts with associated piping. The paper will provide an overview of design and provide a case history of the construction of the tunnel and highlights of the construction methods implemented to date.

By Dogan E. Gücer

In the following note, with the help of a new parameter of strain hardening, the attention is drawn to the close relationship between the relative performances of steels under plastic range cycling and their strain hardening characteristics. If a cantilever beam of rectangular cross section is tested with the arrangement shown in Fig. 1 in reversed bending between constant deflection limits at the lever head, the longitudinal strain-deflection hysteresis shown in Fig. 2 is obtained. There is no lateral strain due to constraint at the rectangular test section.' If the absolute value of strain undergone between a maximum state of tension and maximum state of compression is called A, it will be seen that A decreases with cycling rapidly due to the strain hardening in the test section and the ensuing change in the bent beam profile. It will also be seen that A reaches an approximately stable value around 10th cycle. If we call the first cycle strain range, A,, and that of 10th cycle, A,,, then is an index of the strain hardening capacity at a particular deflection level. A plot of n vs ? is reproduced in Fig. 3 for two ASTM steels: A-302 and A-201. A-302 is a low alloy structural steel, A-201 a low-carbon steel. The specimens were first normalized at 1650°F for 75 min then grooved with a milling cutter; and the notches were ground to 50G finish. The final operation before testing was a stress relief at 1150°F for 75 min. The behavior of the two steels changes around ?1 = 0.8 pct or A,, = A, -n = 0.7. If these curves are compared with the endurance life curves given in Fig. 4, it will be seen that the relative performance of the two steels also change around A,, =. 0.70 pct. The steel with lower strain hardening capacity (7) at a certain strain level shows a longer endurance life, irrespective of their strength levels. Since the exponent governs strain hardening at lower strain levels than the Modulus, the relative values of both parameters also coincide with the change in n values and the relative performances of the two steels at different strain levels. These two observations indicate to the close relationship be-

Jan 1, 1962

By Jay P. Chapman

The basic control requirement for multi-pump, long distance slurry pipelines are discussed and a particular example of an operating slurry pipeline using programmable controllers is presented.

Jan 1, 1983