Search Documents

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005

By G. R. Denham

Innovative designs, mining, construction and reclamation practices are used at PT Newmont Nusa Tenggara's Batu Hijau mine on Sumbawa Indonesia to develop a cost-effective, environmentally sound, stockpile and dumping system. The mine production rate is over 200 million tonnes per year (50 million tonnes processed with 150 million tonnes being stockpiled for processing later or placed in waste dumps). Dump development for over 150 million tonnes per year in a mountainous, tropical environment, while meeting environmental and permitting requirements is not an easy task. The effective implementation requires innovative techniques and practices from every department of the mine.

Jan 1, 2002

Correlation of Air Recovery with Thin Film and Froth Stability in Flotation

Sep 13, 2010

By Philip C. Good

Preliminary studies showed that direct hydrolysis of H2SiF6 to SiO2 and HF at elevated temperatures was subject to many mechanical difficulties, and that corrosion of construction materials was a serious problem. Elimination of SiO2 from the HF product was generally poor. An alternative procedure, hydrolysis of lime-neutralized H2SiF6 by steam at 950° to 1,100° C, yielded a product very low in SiO2. Condensates containing up to 300 g/1 HF were prepared.

Jan 1, 1968

By C. H. Dionne, J. A. Holmes, B. J. Huls

"Falconbridge Limited is presently developing flowsheet alternatives for implementation at the Strathcona Mill. The main thrust for change arises from the need to reject more pyrrhotite from the concentrate. To maintain appropriate levels of sulphur in the smelter concentrate, however, enhanced removal of non-sulphide gangue minerals must be realized. This could best be done in the Non-magnetics flotation circuit.Laboratory investigations were followed by an on-stream pilot test at Strathcona. The application of a column cleaner on the Non-magnetics concentrate resulted in significantly lower levels of fine gangue at equivalent sulphides recovery.This paper discusses the laboratory and pilot testing and results, with a focus on piloting. Also included is a discussion of the Strathcona Mill Flowsheet and the role of the Nonmagnetics flotation circuit.INTRODUCTIONFalconbridge Ltd. is currently developing means to reduce atmospheric sulphur dioxide emissions. One alternative is a reduction in the amount of pyrrhotite in Strathcona Mill concentrate, which reports to the smelter. Pyrrhotite in the Falconbridge ores contains an average of 39 percent sulphur and 0.64 percent nickel. By comparison, pentlandite contains an average of 33 percent sulphur and 34 percent nickel.A consequence of the rejection of pyrrhotite is a decrease in the sulphur assay in the remaining concentrate. This decrease causes downstream difficulties in the roasting process. Therefore, the content of non-sulphide gangue in the mill concentrate must also be reduced in order to maintain sulphur grades adequate for roasting. The resulting concentrate will have lower sulphur dioxide emissions while maintaining nickel production."

Jan 1, 1991

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 m/s (1,500 )fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high-velocity airstream may occur as shields are advanced, allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to 1,600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

Jan 1, 2002

By Sumantra Bhattacharya

The per capita energy consumption in India is 510kgoe/year, the global average being nearly 1818kgoe/year. Correspondingly low is the per capita CO2 emission at 1.25t against the world average of 4.39t.65-70%, at times more, of India?s power generation from about 190,000 MW installed capacity, is however coal fired.India therefore has to secure diversified sources of energy and solar power is increasingly being looked as the real alternative to the existing over dependence on coal. To ensure sustainable solar power it is essential to secure its raw material base that is ?silica?, hitherto considered as ?minor minerals?. That calls for immediately addressing the issues of land availability, solar power cost, developing a dynamic inventory of silica containing minerals, appropriate processing technology and strong regulatory framework for sustainable mining and processing of all silica rich minerals. Keywords: silica, silicon, Thar, power generation, India, quartz, solar power

Sep 1, 2012

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By J. A. Herrick

SOME time ago the writer needed a cheap, light, and portable hydraulic lift or crane, that would be universal in its application, and that might -be suspended from crane-arms, overhead tramways, beams, etc., and serve all the uses of ordinary hydraulic cranes. This was accomplished by the use of a closed cylinder of wrought-iron hydraulic pipe, provided at its top with the ordinary gland and stuffing-box, through the centre of which passed another similar pipe of slightly smaller diameter, forming in effect the ordinary plunger of the regular hydraulic crane. Over the top of this centre pipe or plunger or piston a disk of iron is placed with two arms projecting several inches from the rim, as may be required. Through these arms long iron rods pass, one on each. side, and are fastened in place by nuts screwed to a bearing immediately above and below the disk. These rods also pass through the enlarged head of the lift down through a casting which closes the bottom of the cylinder, which, at the same time, gives them a bearing, and they terminate at a point below the casting equal to the height of the lift of the crane. The rods at this point pass through a disk similar to the top disk and are similarly secured in place. A common hook arranged with a swivel passes through the centre of the disk, and on this hook the load is suspended. For a stationary hanging crane the apparatus is suspended by two rods passing through the head of the lift in similar manner to the two already described, at right angles to the first, and of sufficient length to let the first set play between them and rise to the full height which the plunger will allow. The second set of rods terminates in an iron disk similar to the one at the bottom of the first set, and a hook through this in turn suspends the entire apparatus. In order to adapt the lift to an overhead tramway, single or double, in place of the suspending rods, a projection or offset is arranged on each side of the head of the lift and a journal cast in, allowing the lift to be suspended on pivots arranged as follows

Jan 1, 1879

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

By G. Vouille, P. Bérest

Residual stresses observed in rocks often result from non-compatible initial strains. These stresses can be determined when the incompatibility tensor associated with the initial strain tensor is known. The residual stresses in a cylindrical rock sample can be computed the sample is considered small enough for its incompatibility tensor to be constant. Les contraintes résiduelles, dont on observe couramment les manifestations dans les roches, résultent souvent de l’existence de déformations initiales non-compatibles. Ces contraintes peuvent être calculées lorsque le tenseur d’incompatibilité associé aux déformations initiales est connu. Les contraintes résiduelles dans une éprouvette cylindrique sont données dans le cas où le tenseur d’incompatibilité est constant. Eigenspannungen, die man haeufig in Steinen beobachtet, sind oft Ergebnis einer inkompatiblen Deformation des Anfangszustandes. Diese Spannungen koennen berechnet werden, wenn der Inkompatibilitaets-Tensor der Anfangsdeformation bekannt ist. Die Eigenspannungen einer zylindrischen Probe werden fuer Fall eines konstanten Inkompatibilitaets-Tensor bestimmt.

Jan 1, 2003

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

A method is proposed for the evaluation of the influence of grout prestressing systems on the support resistance offered by timber packs. It is shown that, in order not to reduce the load-carrying capacity of timber packs, grout prestressing systems need to be at least as stiff as a single timber rise. The method was used to establish strength specifications for the grout prestressing systems to be used under non-seismic and seismic conditions. For non-seismic requirements, the 24-hour grout strength needs to be at least 1,7 MPa, and the 7-day grout strength 4,9 MPa. The investigation showed that the proposed strength specification is realistic in the light of current grout-strength capabilities. For seismic requirements, the grout strength needs to be at least 4 MPa and 8 MPa to prevent extensive damage to the grout during seismic events with a peak velocity of 1m/s 3 m/s respectively.

Jan 1, 1996

By Steven Bradshaw, Edson Charikinya

The application of high power microwave energy to secondary crusher products has been shown to induce micro fractures and cracks in the ore. This suggests that heap leaching could benefit from microwave-induced fractures, as the extent and kinetics of heap leaching processes depend on the accessibility of grains to lixiviants, which can potentially be improved through microwave treatment. The density and pattern of microwave induced cracks and how these cracks subsequently affect heap leaching recovery has not yet been investigated. The objective of this study was to apply X-ray micro computed tomography (X-ray CT) to investigate microwave induced cracks in large cone and HPGR crushed sphalerite particles within 3D space. The ore particles were microwave treated in a single mode microwave applicator coupled to a switched mode power supply and a water cooled microwave transmission sub system operating at 2.45 GHz. The ore particles were treated at specific absorbed microwave heating energies of between 2 and 3kWh/t by treating at 6 kW of forward power for treatment times of 1 s. X-ray tomography analysis was conducted on fine (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm sphalerite particles before and after microwave treatment at voxel resolutions of 5 µm, 15 µm and 25 µm respectively. Image segmentation, thresholding and spatial registration techniques were used to study crack patterns in 3D images of HPGR and cone crushed particles. Analysis of the X-ray CT images after microwave treatment shows considerable micro crack formation within the Cone and HPGR crushed particles. The cracks pattern showed interphase cracks propagating across all phases, with no evidence of preferential cracking. A greater density of microwave induced cracks was observed on fine (-5+4.75) mm particles compared to the medium (-16+9.5) mm and (-25+19) mm large particles. The results showed overall increased particle porosity following microwave treatment.

Jan 1, 2014

By R. Demont, A. Pranesh, S. Rakheja

Ethical concerns of in-vivo procedures and poor repeatability of non-invasive techniques have been major limitations in estimating vibration-induced spine loads through experiments. The biodynamic models of seated human body exposed to whole-body vibration (WBV) have evolved for defining the frequency-weightings, enhancement of human responses to WBV, and developing anthropodynamic manikins for seating assessment activities. The widely reported mechanical-equivalent models, solely based on through- or to-the-body biodynamic response functions, do not seem to resemble the biomechanical structure and do not yield information on the dynamic loading and deflections of segments of concern, namely the spine. On the other hand, biomechanical models with representative anatomical structure and anthropometry are being attempted to simulate segmental movements and the coupling effects, using Finite elements (FE) or multi-body dynamics (MBD) formalisms, which could provide important insights into the inter-vertebral forces [1]. While the FE models pose considerable complexities primarily related to characteristics of the bio-material properties, the MBD technique with discrete rigid bodies offers the flexibility to create multi-segment models with relative ease and lower computational cost. In this study, a preliminary multibody dynamic model of a seated human body exposed to WBV along the vertical direction is formulated using MSC/ADAMS software. The model validity is demonstrated by comparing selected responses with the available measured data. Methods The seated human is represented by nine rigid body segments, including: head, neck, thoracic and lumbar torso, pelvis, hands and thighs, as shown in Fig. 1. The rigid bodies are coupled through different rotational and translational joints, some of which are force elements to allow vertical translations and sagittal–plane rotations of the segments. The measurements of transmission of vertical vibration through-the-body generally require subjects to voluntarily maintain a vertical head position to reduce head-accelerometer orientation errors. The head–neck–shoulder joint is thus considered to be rigid. The shoulders are assumed to be rigidly attached to the thoracic segment. The torso is made up of three (upper, middle and lower) segments connected by visco-elastic revolute and translational joints to permit relative pitch and vertical motions. The forces and torques generated by the joints are derived assuming linear stiffness and damping properties, which were identified from published studies. The pelvis is connected to the rigid seat by similar elements representing the visco-elastic properties of the buttock tissues. The two thighs are rigidly connected to the pelvis, while the segment masses are chosen from the anthropometric data for the 50th percentile male subject. The initial model parameters for the joints were obtained from [2]. The model was analyzed to determine the force-motion relationship at the buttock-seat interface expressed in terms of

Jan 6, 2006

By R. Owen, T. Canty, C. Marks

The industrial vision system provides on-line 2D particle size analysis for aggregate slurries in both the overflow and underflow of hydrocyclones. This paper covers required vision system features allowing CCD cameras to function in the harsh environment of a mine milling area. The study conducted demonstrates the system’s capacity to obtain particle size distributions for controlling hydrocyclonic separators. The particle size distribution is obtained within seconds and immediately updated to allow for process adjustments. Results are then provided as a graphical computer generated display or output as a 4-20mA current loop for process control. The primary use of the vision system is in classifying particles in cyclone overflows which are often a few microns in size. Typical size information for actual mine slurry samples are presented and possible control schemes discussed.

Jan 1, 2002

By R. Zivojinovic, S. Vujic

The structural age of the capital mining machinery, representing a part of the system of the Electric Power Industry of Serbia, has been dictated by the initiation and development of open pit coal mines. For example, the oldest bucket wheel excavators were installed some thirty-four years ago, and the average life of the relevant machinery exceeds twenty-two years. Operation of both capital equipment and machinery has direct effects on economic and business activities of open pit mines, and consequently forced us to make a decision and study thoroughly the problem of establishing the optimum exploitation life of capital mining equipment at the open pit coal mines of the Electric Power Industry of Serbia. The aim of this paper is to define and discuss the relative problems as well as to find out the possible solutions and establish the methodology for estimating the optimum exploitation life of machinery. The study was successfully carried out by a team of scientists engaged from and coordinated by the Department of Computer Science of the Faculty of Mining and Geology, University of Belgrade. This paper presents the key observations covering the subject problem. Keywords: Mining, Opencast exploitation, Coal, Optimization, Exploitation life, Capital machinery, Electric power industry, Dynamic programming.

Jan 1, 2003

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

Jan 1, 1968