Search Documents

By H. P. LeVan

Research was conducted to examine the feasibility of extracting manganese from Georgia umber ore by a three-stage continuous sulfuric acid-ferrous sulfate pickle liquor leaching process. A continuous cyclic process for treating the umber was operated successfully, using a synthetic solution simulating a ferrous sulfate fortified anolyte solution discharged from a manganese electrolytic cell as the leaching medium. Leaching efficiency based on removal of the manganese from the ore ranged from 83 to 89 percent for all systems tested.

Jan 1, 1965

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By Detnet Solutions

1. “Daisy-Chain” concept The term “daisy-chain” stems from the fact that when the HotShot? detonators are connected there is a chain or electrical path for electrical current to flow from detonator A to detonator B, detonator B to detonator C etc until the path is terminated by an electrical means. The “daisy-chain” concept has long been used in electronic detonator systems, historically used in Expert Explosives’ ExEx 1000 5/6 wire system and currently in use in African Explosives Limited (AEL’s) Electrodet? electronic detonator system and has been adopted as the basis upon which the “auto-programmability” of the HotShot? electronic detonator system functions. HotShot? Detonators are connected to each other in a string, completing a “daisy chain”, and during the auto-detection mode of the control equipment, it is possible for the equipment to determine the order of hookup of the detonators as well as map the entire blast layout. The auxiliary components (Row Controllers & Branch Controllers) assist the control equipment in mapping the entire blast by indicating different points on the blast, i.e. The inflection point of a row of blast holes on a closed chevron timing pattern, the beginning of row of blast holes on open chevron timing pattern and extra blast holes or extra blast rows.

Jan 1, 2004

By Rudolf Gahl

THE history of flotation in America is very short, at least as far as the large-scale application of the process is concerned. It is remarkable how many important developments have taken place inn the last few years and are already being extensively utilized. What was new a year ago, seems almost commonplace now. For this reason it is with hesitation that I follow the suggestion: of Dr. Ricketts, President of the Institute, to describe the experiences of the Inspiration Consolidated Copper Co. with the flotation process. TESTS CONDUCTED IN SMALL TEST-MILL When the Inspiration company first decided to build a concentrating plant, nothing was known about flotation, and the process was to be gravity concentration pure and simple. Demonstration Tests Conducted by Minerals Separation Co. While plans were being prepared by H. Kenyon Burch (who had been intrusted with the design and construction of the concentrator) the Minerals Separation Co., a concern at that time little known in America, asked and obtained permission to demonstrate the value of its flotation process for Inspiration ore. As. a consequence, a small 50-ton flotation machine of standard design was added to the company's test plant and started to operate in the beginning of 1913. This marks the beginning of flotation at Inspiration. The results obtained with this machine, which was operated by members of the Minerals Separation staff, so far surpassed what this company anticipated that it was decided to continue flotation tests for this purpose, and two of the flotation experts of the Minerals Separation Co., I. L. Greninger and G. A. Chapman, were retained. L. R. Wallace, now superintendent of the Miami works of the International Smelting Co., was at that time metallurgist of the Inspiration company and in that capacity took an active part' in these tests. Great credit is due to him for his quick recognition of the possibilities of flotation.

Jan 9, 1916

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

By H. Ozturk

In this paper, the computer program ‘SHAFT’ developed for estimation of support requirements for circular mine shafts is introduced. Theory of support design is based on the analytical solutions of circular excavations under non-hydrostatic loading (Detourney and St. John1), and Lame’s thick-wall cylinder theory (Timoshenko6). For rock mass strength property determination Hoek-Brown failure criterion (Hoek et al.2) is used. Mainly two types of support, concrete and steel are taken into consideration as a support member. Program is written in Quick Basic language. Input parameters of the program are shaft radius, number of zones having the same properties along the shaft depth, and depth, unit weight, horizontal to vertical stress ratio, GSI, and uniaxial compressive strength of intact rock of each zone, and compressive strength and safety factor of support member. Output of the program is the graphical representation of shaft with the required support member and thickness throughout the depth of the shaft.

Jan 1, 2003

By K. R. Coulter

"Good morning gentlemen. I am very pleased to have this opportunity to tell you a few of the things that happen within a completely unrelated activity, the electroplating industry, except that it does consume metals and has some slight similarity of problems so far as cyanide is concerned.First, just a few general terms about the industry. It is a relatively unsophisticated industry technically, and in many instances there are serious problems in obtaining staff that can operate the various systems that are currently available for destroying cyanide or precipitating metals.I would suggest to you that if you are investigating any system that you consider very seriously the personnel that are actually going to run it. The installation people; probably have some idea what it is all about but the operators must be chosen for their ability and not because they just happen to be available.We perhaps have another area in common. There is very little money for capital expenditures that produce no immediate return or even eventual return on the investment.The industry is largely made up of ""Jobbers"" who are strictly electroplating. There is another group in which the electroplating is captive as in large companions where it is a convenience operation. Also there are specialists, who do other things besides plating but it is a very major part of their operation. This applies to the automotive parts industry.Cyanide applications in the plating industry will be for copper, zinc, cadmium, silver, brass, and gold. Cyanide waste solutions come from those solutions adhering to the plated parts, and from the occasional discharge of the plating bath solutions. Also, in a related industry, the heat treating people with cyanide case hardening have some high concentrations of cyanide to dispose of. Concentrations of cyanide that we treat are 2500 parts per million or higher especially in wastes from heat treating. Solution volumes might be as low as 100 gallons per hour in a well run, carefully operated rinsing system. It may be as high as 3000 gallons per hour where dilution occurs."

Jan 1, 1973

By Roe-Hoan Yoon

"Industrial flotation columns often suffer from low recoveries and high maintenance requirements because of poorly-designed air spargers. The MicrocelTM bubble generators were developed at Virginia Tech to overcome these problems. In this system, small air bubbles are generated by circulating a portion of the flotation pulp through a set of static in-line mixers. The small bubbles improve flotation kinetics and allow a higher recovery (or capacity) to be achieved. Other advantages of the system include reduced air consumption, plug-free operation and on-line maintenance. This article discusses the advantages of the MicrocelTM bubble generators and presents examples of successful in-plant demonstrations.IntroductionColumn cells are widely accepted in industry for cleaner operations because they are more selective than mechanically-agitated conventional cells. The improved selectivity can be attributed to the use of wash water which minimizes the entrainment of fine gangue particles into the froth product. Columns may also produce higher recoveries if the air sparging system is properly designed and steps are taken to minimize back-mixing. Furthermore, the quiescent conditions afforded by column cells may be beneficial for recovering coarse particles that are readily detached from bubbles under more turbulent conditions. Also, properly-designed columns offer advantages in terms of savings in floor space, reduced operating and capital costs, and simplified circuitry.It is unfortunate, however, that some of the advantages of columns are not fully realized in industrial practice. Some column circuits are unable to achieve their design capacity, while others require extensive maintenance programs. These shortcomings can usually be attributed to deficiencies associated with the design, scale-up and operation of the air-sparging system. In this article, some of the basic problems associated with commercial air sparging systems are discussed and alternatives are suggested."

Jan 1, 1994

By A. F. Lee

A pick-up apparatus capable of yielding quantitative results has been described. Studies of some collector-mineral systems have been presented to illustrate the versatility of the apparatus and prove the validity of results.

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

Management of Mining Wastes in European Union and Developments in Turkey

Sep 13, 2010

By Mingchun Lu, Yunjin Yan

"This paper describes a new type of bell-less top installed on two relined blast furnaces at Tianjin Iron Works and another new-built at Echeng Steel Works in China. A compact installation was presented for existing furnace top innovation with the least reformation of existing top structure. A water cooling and sealing gearbox used for driving the chute discards completely the traditional idea about necessity of continuous supply of cooling gas for the gearbox. A multiring spreader and its dozens of selectable charging patterns enables an operator to achieve optimal burden distribution easily under the condition of a minimum investment of control equipment. Some useful conclusions have been made through a small-size model and a full-scale model tests. The excellent characteristics and the superiority of the new top have been fully proved at both works.IntroductionIt is known that there are some advantages with the bell-less top of a blast furnace: suitable for furnace to operate at high top pressure, capable of realizing optimal burden distribution, less investment and maintenance costs, etc. But why do most of blast furnaces in the world still remain using conventional bell top. One of the concerns is that current bell-less tops still have some shortcomings:1) The height of a current bell-less top might be lower than three or four-bell top or two-bell plus valve seal top, but still much higher than an ordinary two-bell top.2) The gearbox for driving the rotating chute is positioned onto the lip of the furnace. It is subject to attack by crude hot bf gas. Continuously pumping cooling gas (pressurized nitrogen or clean bf gas) into the gearbox is indispensable to withstand such a harsh working environment. Therefore, a plant furnished with blower8 and its ancillaries has to be built, It involves a large sum of investment and much expense in its annual running costs.3) Although the current bell-less charging device as a means of controlling burden distribution possesses a wide range of freedom, it is difficult to realize optimal burden distribution. There are some large blast furnaces realized better burden distribution, but sophisticated control means is indispensable so that the investment of control means is much higher."

Jan 1, 2000

By L. C. Brichta

The Melrose zinc-lead. deposit is in an area of structural disturbance of sedimentary rocks in the Melrose mining district in Cherokee County, Kans., 25 miles west of Joplin, Mo., adjacent to the northwest limits of the Tri-State district. Mining and milling in the Melrose district has been sporadic and. very limited, largely due to the high cost of exploration through great thicknesses of barren rock, 350 to 440 feet overlying the ore deposits. No mining has ever been done on the Melrose zinc-lead tract, but it has been drilled extensively. The drill-hole logy indicate extensive structural deformation, silicification, and zinc-lead deposits in the Boone limestone-chert formations of the Mississippian series, which is overlain by thick-bedded Pennsylvanian shale and sandstone. Analyses of samples from Bureau of Mines drilling indicate the ore minerals are sphalerite and galena with no evident oxidation. During the period from November 2, 1949, to March 13, 1950, the Bureau of Mines investigated the deposit by churn drilling and sampling 23 holes aggregating 10,405 feet of bore. Factual data on the investigation and logs of holes drilled by private parties and the Bureau of Mines are presented in this report.

Jan 1, 1951

By G. L. Oldright, F. W. Schroeder

Very great changes were made in the dimensions of the smelting hearths of the furnaces in the period from about 1800 to 1906, the length increasing from about 11 to 116 ft., and the width from 8 to 19 ft. During this time the tonnage smelted increased from about 9 to 250 tons per 24 hr., and the tons of charge smelted per ton of coal increased from 0.77 to 4.3. Dr. Mathewson3 noted no great difference in the "fuel ratio" (i. e., the amount of charge smelted per ton of coal) as the furnace at Anaconda was increased in length by stages from 85 to 116 ft. (The percentage of copper in the slag, however, was lowered from 0.42 to 0.36 per cent. The other components of the slag were not given.) Lump coal fired on grates was the fuel used during this period. The practice in operating the furnaces over such a length of time naturally varied considerably, and there were differences in composition and nature of the charge, yet it may he considered that the improvements made were due largely to increases in the size of the furnace used. Doubtless some credit should be given to improvements in operating technique, like changes in the methods of firing the lump coal. However, the greater part of the advance was probably due to factors influencing the

Jan 1, 1928

By Louise Reber

THE town of Jerome is located in Yavapai County in north central Arizona. It has a population of over 6000 people and the two important mines of the district, the United Verde and the United Verde Extension, lie almost within its limits. Perched high on the southwest side of the Verde Valley, at elevations of 4800 and 5500 ft.. (1463 and 1676 m.), both mines have long tunnels from their lower levels through which ore is hauled to their respective smelters. The two smelter towns of Clarkdale and Verde, out in. the center of the valley and about 2000 ft. (609 m.) below, form part of the wide panorama that meets the eye at Jerome. This panorama and the topographic and surface features and the geologic formations are shown in a separate pamphlet. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "the rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the, highest parts of the Black Hills, which bound the valley to the southwest. The two lava-capped mesas, known as Mingus and Woodschute Mountains, form the culmination of the Black Hills. That part of the old Black Hills mining district which lies between their crests -and the Verde River is now known as the Jerome or Verde copper district. However, if the smelters are not included, a strip about 7 mi. long and 3 mi. wide (11 by 5 km.) embraces practically all the properties belonging to the Jerome district. This strip lies parallel to and along the side of the Verde valley from about First View, 2 mi. northwest of Jerome, to the neighborhood of Allen Spring, near the south end of Mingus. Mountain. The rank of the district in copper production, as well as features of peculiar geologic interest in connection with the ore occurrences, entitle the district to much more consideration than it has received in the literature of copper mining. Arizona stands preeminent as a copper-producing state. In 1918, it produced four-tenths of the total amount produced in the United States, and nearly equaled the, combined production of its three chief competitors, Montana, Michigan, and Utah. The production of the Jerome district places it in the sixth place among the copper

Jan 8, 1920

By Xiang He, Xinzhong Wang, Ning Li, Bao Cao, Hongyang Bai, Zhigang Du

Revealing the periodic fracture pattern of the main roof and the key influencing factors of the support resistance is crucial for strata control and support selection of the shallow buried working face with large mining height. Based on the cantilever beam theory, an improved step rock beam model, and the measured strata pressure data of the 12,401 working face in Shangwan Mine, the mine pressure behavior law of the shallow buried with a large mining height working face was analyzed. The results show that both ratio of maximum principal stress to load (σ1/q) and ratio of maximum shear stress to load (τmax/q) inside the main roof increase with increasing periodic advancing distance, while the ratio of maximum shear stress to maximum principal stress (K) is the opposite, indicating that the increase rate of σ1/q is higher than that of τmax/q. K is less than 1 when the periodic advancing distance exceeds 8 m, indicating that the periodic fracture of the main roof will be dominated by tensile failure. Support resistance increases with increasing immediate roof thickness, main roof thickness, periodic fracture step distance of the main roof, and mining height, and decreases nonlinearly with increasing friction coefficient of periodic fracture rock block hinge surface. The main roof thickness, the periodic fracture distance of main roof, and the friction coefficient of the hinge surface of the periodic fracture rock block are the key factors influencing the support resistance. The advance breaking of the main roof and increasing the friction coefficient of the hinged surface of the main roof can reduce the support resistance of the working face. The support resistance of the 12,401 working face in Shangwan Mine presents an arch distribution characteristic. The average periodic weighting step interval, average support resistance, and dynamic load coefficient are 15.6 m, 17,552 kN, and 1.3, respectively. Finally, the rationality and validity of the model are verified by comparing the measured and theoretical values of the support resistance in the 12,401 working face of Shangwan Mine and other shallow coal seams with large mining height.

Apr 22, 2024

The theme i wish to develop in this talk is how we might make use of the scientific and technological knowledge we now have ofextraction metallurgy to meet the present-day needs of the production industry.Before doing so, I would like to say a few words in tribute to Dr. G.K. Williams since he was a past master at precisely what I wish to talk about. I knew G.K., as everybody called him, during the time he spent at Avonmouth in the late 40's and in the 50's. Later, when he was ostensibly retired, I had the pleasure several times of lunching with him when I was visiting Melbourne.When G.K. was at Avonmouth, the Imperial Smelting Process was in that capricious adolescent stage in between the pilot plant and the full-scale commercial unit. G.K. was a great collector of process plant data which hung in cascades from the walls of his office and-from his hand-operated desk calculator. What G.K. understood very well were the basic metallurgical and engineering principles of what was going on in the sinter machine, the shaft furnace and all their ancillaries.

Jan 1, 1985

By Carlos Rivera

En el proceso de clausura de labores explotadas en a mina subterránea se emplean estructuras de cerramiento, con la finalidad de que estos sectores alcancen la seguridad física, química y protección ambiental en el interior de la unidad de producción y sus alrededores. Sin embargo, uno de los problemas que se presenta durante la explotación de la mina, responde a el abatimiento de la napa freática, donde los sistemas de drenaje captan y conducen el agua por las galerías ubicadas en los niveles inferiores de las minas, generando el Drenaje Ácido de Roca. Por ello, el presente texto señala la construcción de las estructuras de cerramiento proyectadas y construidas en un nivel freático para así reducir el oxígeno requerido para la formación del DAR. Asimismo, se muestra la estructura proyectada y construida en el Nivel 490 de la unidad de producción Julcani, perteneciente a la Compañía de Minas Buenaventura S.A. A y la aplicación práctica de los métodos usados para su diseño.

Sep 13, 2001

By S. Finsterle, R. C. Trautz

We performed numerical modeling studies to investigate water seepage into underground openings excavated in unsaturated fractured rock. Water seepage is a key factor affecting the performance of a nuclear waste repository such as the one proposed at Yucca Mountain, Nevada. The amount of water dripping into an underground opening depends on the connectivity and permeability of the fracture network as well as on the capillarity of individual fractures intersecting the opening. We developed a high-resolution numerical model of an unsaturated fracture network and examined the appropriateness of seepage predictions using a fracture-continuum model. Model calibrations to liquid-release tests performed at Yucca Mountain are also discussed.

Jan 1, 2000