Search Documents

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combusts on products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting with gasified carbon (CO) produces (14,140 - 3,960) 10,180 B.T.U. which is (10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total combustion. It is not only logical but practical in partial combustion, converting bituminous coal to gas, to generate the gas with reduced nitrogen dilution.

Jan 1, 1936

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004

By Hector M. Henao

To provide thermodynamic data for converting nickel matte to liquid nickel at high temperature, an experimental study was conducted on the phase equilibrium between the Ni-S alloy and the FeOX-SiO2, FeOx-CaO, and CaO-A12O3 base slag in a magnesia crucible and the CaO-Al2O3-MgO slag in an alumina crucible. All experiments were carried out at 1773 K under controlled pso2 of 0.1 atm and po2 in a range between 5x10- and 10-5 atm by using CO-CO2-SO2 gas mixtures. The dissolution of nickel in the slag was found to be minimum for the CaO-Al203¬-MgO slag with a molar ratio of NCaO/NA1203=1.7. The solubility of nickel in this slag at p02 of 6x10 atm (just before the precipitation of solid NiO) was 4 mass%. This result suggests that a CaO-A12O3 base slag could be used in converting Ni-S melt to nickel while minimizing nickel losses to the slag.

Jan 1, 2002

By Luiz Gabriel da Silva Nascimento

Um material que vem sendo muito estudado quando imerso na matriz de outros materiais, são os nanotubos de carbono, uma forma alotrópica do carbono, que são milhares de vezes mais finos que um fio de cabelo, mas que apesar disso, possuem uma extraordinária resistência mecânica. O alumínio por apresentar um baixo peso específico e ter a facilidade de se unir a outros materiais pode nos fornecer excelentes propriedades e muitas aplicações tecnológicas. Através de ensaios metalográficos e mecânico, esse trabalho avaliou o comportamento microestrutural e de microdureza do alumínio depois da adição nanotubo de carbono e nanotubo mais níquel em sua estrutura. Foi usado um processo de fabricação por fusão com agitação mecânica por um pequeno motor elétrico e resfriamento brusco por água. Depois das análises nesses diversos materiais, com composição diferenciada, o que melhor apresentou propriedade mecânica foi o Al-3%Ni+nanotubo de carbono.

Aug 7, 2018

By M. I. Abbas, M. A. Shahin, M. S. Ahmed

"The influence of annealing of galvanized steel (galvannealing) on its corrosion kinetics in a saturated solution of Ca (OH)2 has been studied by means of the polarization resistance method.Galvannealing heat treatment was carried out at 450°C and 550°C for varying times. Annealing at 450°C for 24 hr or at 550°C for 5 hr showed the highest corrosion potential (Ecorr) ~= - 400 m V/ SCE as well as, the lowest corrosion current density (icorr ~= 3 mA.cm-2, while Ecorr and icorr of the unheated specimens were ~= - 1400m V/SCE and == 20 mA.cm-2, respectively.Polarization curves were also obtained for the as-received galvanized specimens together with the galvannealed ones.INTRODUCTIONHeat treatment of galvanized steel (i.e . galvannealing) is carried out at a temperature range of 450°C to 550°C for a time sufficient to convert the free zinc coating to an alloyed one consisting of layers of iron-zinc intermetallic compounds. Table I is a review of the properties of the Fe-Zn intermetallicphases while Figure I is a reproduction - of the Fe-Zn equilibrium phase diagram taken from Hansen.Several authors have studied the formation of intermetallic phases through the interdiffusion of Zn/Fe couples. Their results confirmed the stability of intermetallic phases that could be shown up on the outer surface as a result of galvannealing of galvanized steel.Bernick and Sievertv"" investigated the processing of galvan nealed steel. They found that the galvannealed coating with the best forming qualities consisted of a mixture of Zeta phase and Eta phase."

Jan 1, 1989

By R. R. Klimpel

The use of froth flotation as a means of separating and upgrading sulfide mineral concentrates is standard industrial practice throughout the world. Froth flotation is also widely recognized to be a very complex system having highly interactive and often self-compensating factors at work. Several summary articles have been recently published which discuss at length some of the important practical aspects of optimizing the use of existing commercial flotation reagents. Klimpel (1987). Klimpel and Hansen (1987a), Klimpel and Hansen (1987b), and Klimpel (1988). It is apparent from monitoring the industrial practice of sulfide mineral flotation over the last decade that considerable progress has been made in optimizing the operating aspects of flotation. For example, the availability of improved instrumentation and related computer devices, modified mechanical flotation cell designs, better reagent dosage control leading to less reagent usage per ton of ore, blending of feed ores, more attention to coarse and fine particle flotations, etc., are all examples of this progress.

Jan 1, 1988

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003

By Marina de Menezes Lopes

Sabe-se que a presença de ultrafinos em plantas de beneficiamento de minérios pode comprometer a eficiência dos processos principalmente os de flotação, uma vez que fenômenos como o slime coating e o arraste hidrodinâmico das partículas ocorrem fortemente. Além disso, concentrados contendo uma proporção significativa de ultrafinos terão dificuldade de serem filtrados gerando tortas de alta umidade. Este trabalho teve por objetivo estudar o efeito do dispersante AGLP consumido atualmente na planta de beneficiamento da Votorantim Metais Vazante, na flotação do minério silicatado de zinco e avaliar o efeito da sua dosagem na umidade do concentrado final produzido. Para tanto foi realizada a caracterização granulométrica das amostras e conduzidos testes de bancada de sedimentação, filtração e flotação em diferentes dosagens de AGLP. Como era de se esperar, os resultados identificaram que o concentrado de granulometria mais grosseira obteve melhor sedimentação e umidade. Já os testes de flotação indicaram que a dosagem ótima do dispersante em torno de 400g/t garante um concentrado de qualidade, sem perda de recuperação metalúrgica e com umidade adequada para que seja transportado.

Aug 17, 2017

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed a series of lab tests to evaluate the respirable dust removal capacity of an industrial air-cleaning fan. Limestone and coal dust were tested separately in NIOSH’s full-scale drill table simulator at the Pittsburgh Mining Research Division (PMRD). Gravimetric samplers with Dorr-Oliver Cyclones and 37-mm filters were used at two upstream and four downstream locations inside and outside of the drill shroud chamber. There were six tests performed for both the limestone and coal dust experiments. In the limestone tests, an average respirable dust concentration of 98.86 mg/m3 was achieved upstream of the air-cleaning fan. The filter results show that the averaged respirable limestone dust reductions were 7.84%, 8.81%, 10.94%, and 18.02% at the four sampling locations downstream of the fan. In the coal tests, upstream samplers achieved an average of 129.03 mg/m3 of respirable coal dust. The averaged dust reductions were 9.54%, 9.83%, 18.54%, and 19.21% at the four downstream sampling points. The results indicate limited cost benefits of using this technology because of the relatively low dust reductions determined from this laboratory study.

Feb 1, 2023

By Roberto Rosario

El presente trabajo la factibilidad de la evaluación realizada en la capacitación del personal minero. Esta evaluación comprende el control de calidad del producto formativo y para ello, es necesario que se definan los objetivos deseados con dicho trabajo y que los efectos se mantengan a lo largo del tiempo. En esta perspectiva, la capacitación fue aplicada en Pan American Silver de la mina Quiruvilca en el mes de octubre y la evaluación se desarrolló dos meses después. Las etapas de la evaluación fueron: entrada, salida y desempeño (autoevaluación). Esta última permitió conocer el conocimiento obtenido en los participantes, concluyendo en un resultado positivo en tanto mejora el autoestima, actitudes, comportamiento laboral y desempeño.

Sep 13, 2001

By David D. Davidson

Commodities remain hot for the time being, but for how much longer? The bulls point to global economic growth lead by China?s insatiable demand for raw materials. To further emphasis the bullish view they point to the emergence of India for follow through demand. The bears remain convinced China?s growth is unsustainable and with higher interest rates and high oil prices, the United States economy is poised to slow. Both groups can make a convincing argument and both will be proven right in the fullness of time. Profitability and balance sheet strength for the mining industry has rarely been better. Is this a time to be bold or cautious? In this paper, the author will address the dilemma facing today?s management as they pursue growth and try to minimize risk.

Apr 1, 2005

By A. V. Myaskov, V. S. Valavin, K. D’Elia, I. O. Krylov, Vu Van Toan, T. I. Yushina

"The purpose of this research is the development of a technology for processing the concentration tailings of limonite ores at Kamysh-Burun Mining and Processing Complex into an iron- containing product for ROMELT process. In the concentration and metallurgical processing of iron ores, substantial amounts of waste are generated (tailings, slimes, slags, metallurgical dust, etc.) that can be converted into a commercial product if is properly processed. This article presents the results of experimental studies of the feasibility of processing iron- containing tailings of Kamysh-Burun deposit (slimes from Verkhne-Churbash storage facility (VCh sample) and dumped waste of Kamysh-Burun (KB sample)) to obtaining valuable components for further uses. Applying Mossbauer spectroscopy has been shown that the iron minerals in the studied samples are technogenic varieties of iron hydroxides. The most suitable technology is the magnetic roasting process, since iron hydroxides are easily transformed into a magnetic, easily recoverable form. Have been shown the advantages of a two-stage magnetic separation, in a strong field and with polygradient separators. Concentrating this material through magnetic methods makes it possible to increase the iron content to 20-21 %. Magnetic concentration of the deeper layers materials results in iron- containing concentrates with a total iron content of up to 58% whit a phosphorus content of about 2%. Reducing the phosphorus content is possible by blending upper and lower layers of the material at a ratio of 1:1. Thus, it is possible to process the material accumulated in the slime storage facility using the ROMELT process combined with preliminary three-stage magnetic concentration and disposal of tailings with the permissible iron content of less than 5%. Wastes from smelting will be slags suitable for use in construction industry. The Kamysh-Burun material preparation for ROMELT process should be performed applying gravity-washing with separation of the -0.4 mm fraction and additional blending for dephosphorizing the concentrate. The smelting will produce pig iron and slag."

Jan 1, 2018

By Elli Nurminen

Keywords: Thermal conductivity of sulphates, flash smelting, heat recovery boiler, flue dust Accretions and build-ups in metallurgical heat recovery boilers decrease the efficiency of the heat transfer and may cause process shut downs. Transient plane source method (Hot Disk) has been applied to measure the thermal conductivities of the Copper Flash Smelting flue dusts. Thermal conductivities of copper, iron and zinc sulphates, and process flue dusts were measured. The results indicate that all the components are effective thermal insulators, having a thermal conductivity of less than 1 W/mK. Decreasing dust layer porosity has an increasing effect on thermal conductivity. Insulating layers on the boiler walls decrease greatly the heat transfer efficiency of the boiler. The gathered information will be used in CFD-modelling of the process, and in the process control.

Jan 1, 2005

By I. Stapf

Systematic investigations on silver-rare earth metal systems have been extended on the Ag-Ce system in order to clarify the discrepancies reported in literature. The phase diagram has been reinvestigated on the base of thermal analyses and of microstructure examination on cast and annealed specimen. All intermetallic phases Ag4Ce, Ag3Ce, Ag2Ce and AgCe show no extended range of homogeneity, they melt congruently fm), or decompose peritectically (d) at 815 °C (d), 1030 °C (m), 855 °C (d) and 855 °C (m), respectively. The system shows eutectics at 793 °C/10 at.%, 780 °C/42 at.%, and about 505 °C/81 at.% Ce. d-Ce dissolves up to 2 at .% Ag and decomposes metatectically at 710 °C. Furthermore, the phase transformation of the intermetallics would be clarified. The phases Ag5Ce and Ag51Ce14 reported in literature could not be verified.

Jan 1, 1984

By A. Redman

Aquatic organisms are sensitive to free cyanide (HCN) though the presence of certain metals that can form stable complexes and thereby reducing both the amount of bioavailable cyanide. Recent work has suggested that consideration of HCN rather than total cyanide can provide the basis for water quality criteria. Cyanide is often present in complex effluents that affect speciation and bioavailability. We have developed a model to predict the speciation of cyanide in complex effluents and have shown that this model can predict the toxicity of metal-cyanide complexes in terms of HCN. This study evaluated available cyanide toxicity exposures with this model to assess the role of water chemistry (e.g., metal-cyanide interactions) on the observed. Toxicity endpoints based on total cyanide ranged over several orders of magnitude for a variety of metal-cyanide mixtures. However, predicted HCN concentrations among these same tests described the observed toxicity data to within a factor of 2. Aquatic toxicity can be well described using HCN though in certain metal-cyanide mixtures toxicity was jointly described by HCN and elevated levels of bioavailable metals. This work was performed in support of an industry-sponsored reassessment (Gensemer et al 2006) of the U.S. EPA water quality criteria for cyanide (EPA 1985) using free cyanide as the basis for the re-calculation. The work presented in this manuscript presents technical support for using free cyanide as the preferred basis for this recalculation.

Jan 1, 2011

By Joseph Gersic

The U.S. Bureau of Mines assessed mineral resources of the BLM Malheur-Jordan Resource Areas (MJRAs) in southeastern Oregon in 1993 and 1994. The study relied heavily on acquiring and analyzing existing data. In order to efficiently handle and analyze a large quantity of data, a minerals information management program, informally called MINFO, was developed as a frontend for three databases created to store basic information gathered during the minerals resource assessment. The MINFO program will also provide the BLM with a method of tracking and updating minerals information in the future because program modules in MINFO allow the addition of new data and the correction of errors, creation of print files, transfer of data to other database formats, exportation of data to other software packages, and creation of AutoCAD script files to be used in conjunction with AutoCAD to produce maps. The report specifically identifies significant past and present mineral exploration and development activities and possible areas of future mineral exploration and development. These areas are informally designated as areas of development interest or ADIs. The report contains a scenario of what mineral development might reasonably occur in the foreseeable future if the BLM does not substantially change its present resource management plan, and it shows the possible socioeconomic impacts of that development. The uncertainty of the political and economic situation makes it extremely challenging for the USBM to accurately predict a reasonably foreseeable development scenario. The reasonably foreseeable development (RFD) scenario developed by the USBM for the BLM indicates short-term RFD of minerals should have a negligible socioeconomic impact, and longer-term RFD of minerals should have a slight socioeconomic impact on the MJRAs. The mining industry is facing a rapidly changing business and regulatory environment in Oregon. Several signal changes have occurred recently, including State regulations that require significant bonding prior to the startup of "chemical process" mining, an initiative by a special interest group to stop all chemical process gold mining within the State, and an opinion by the Oregon Attorney General (AG) banning all forms of placer mining without exemption. In the AG opinion, not even gold panning is allowed, and the prohibition applies to mining claims on Federal lands. The State legislature may amend the statute to allow small scale placer mining to occur, as was allowed under an AG opinion issued in 1982. These and other changes occurring at the local, State, and National levels are making it more challenging for the mining industry to operate in the United States. Several epithermal gold properties in the MJRAs attracted the mining industry's interest. Only the Grassy Mountain Project of Newmont Grassy Mountain Corporation may be developed in the next few years. It is probable that at least two other properties will be developed if Grassy Mountain is successful. Mining companies are waiting to see the effect recently promulgated State mining regulations and more stringent proposed regulations, particularly bonding regulations, may have on Grassy Mountain. Resources of bentonite, diatomite, and zeolite are abundant. The almost Ubiquitous stone, sand and gravel, and semiprecious gemstone resources also were examined. Little environmental or socioeconomic impact is expected from reasonably foreseeable development of these mineral resources.

Jan 1, 1994

By Anna Eleria, Joseph Welna, Jim Herber, Nathan Campeau

Constructed by stonemasons over 120 years ago, a portion of the Trout Brook Storm Sewer Interceptor (TBI) owned and operated by the Capitol Region Watershed District in Saint Paul, Minnesota, needed rehabilitation. A routine inspection of the 10-foot limestone block tunnel revealed degraded and missing mortar between the blocks, allowing significant infiltration and soil migration through the tunnel joints. Conditions, including damaged and missing blocks, were considerably worse in a 250-foot-long segment beneath a busy mainline railroad corridor. Barr’s solution included tuck-pointing to repair the mortar joints, shotcrete overlay, and construction of a hybrid cast-in-place/shotcrete “tunnel within a tunnel” to support the mainline railroad loads.

Jun 13, 2021

By N Dube, K L. Sandvik, C Mutevhe

Trojan Nickel Mine is the largest producer of Ni, Cu and Co in Zimbabwe. The mine has operated a nickel flotation concentrator and base metal refinery continuously since 1969, creating 28 million tonnes of sulfide bearing tailings, five million tonnes of permanent waste rock and about seven million tonnes of smelter slag. Exposure of the sulfide bearing minerals renders them susceptible to oxidation in the presence of water and oxygen, resulting in acidic solutions with elevated concentrations of total dissolved solids, sulfate, metals and residual flotation chemicals in various waters draining from the mine site. These pollutants pose a direct threat to the environment and human health, and understanding their deportment and behaviour in the various waste streams is essential in the mineÆs environmental objectives to prevent or minimise adverse impacts arising from its operations. A geochemical assessment of the pollutants was carried out to compute a mass balance between the major sources of pollution and the distribution and fate of pollutants in waste streams from the mine site. Waste rock, tailings, surface water, ground water and sediments were sampled, tested and analysed. Mineral composition and water chemistry data show that geochemical reactions are responsible for the release of pollutants from waste rock, tailings and plant spills. Drainage from the mine area is near neutral due to buffering by magnesium carbonates in the fine fraction of the tailings. The natural wetlands that exist downstream of the waste rock and tailings dams are effective in reducing metal loadings to water courses. However, solutes and heavy metals are occasionally released to surface and ground water, when their concentrations peak during the dry season. The results demonstrate the necessity to understand the natural chemical processes that characterise the distribution of pollutants in nature and how such knowledge can be used to develop cost effective methods to remediate pollution in the natural environment.

Jan 1, 2006

By S. R. LaBrooy, J. Avraamides

Thermal reactivation of eluted carbon is an essential part of most carbon-in-pulp gold recovery plants. The effectiveness of the reactivation procedure depends on the nature and level of contaminants adsorbed on the carbon, the efficiency of the elution and the temperature, residence time and atmosphere within the kiln. The most commonly used kilns are evaluated in terms of their operating parameters and performance. Data obtained both in the laboratory and in the field emphasize the importance of carbon feed moisture content, kiln atmosphere and carbon conditioning on the activity of the kiln product.

Jan 1, 1998

By Victor J. Scaravilli

This report is based on experience developed on the construction of one contract for the Buffalo, New York subway. The Buffalo subway is under construction for the Niagara Frontier Transportation Authority and is called the LRRT-Light Rail Rapid Transit or more commonly the Metro. The Initial Route of the Buffalo subway construction started early in 1979 and is scheduled for completion in May, 1984. The initial system includes 5.2 miles of underground construction, 1.3 miles at grade for a total of 6.5 miles of subway system. A total of fourteen stations, eight underground and six at grade are included on the system. The Initial Route has a planned expansion to 17.3 miles in the future. On January 15, 1979, a Joint Venture of S & M Constructors, Inc., Solon, Ohio, James McHugh Construction Co., Chicago, Illinois, and Kenny Construction Company, Wheeling, Illinois, was awarded contract 100031, the Line Tunnels from Amherst Street to South Campus in northcentral Buffalo between Delaware Park and the State University, (see Fig. 1, Location Plan) This $35,000,000.00 contract was designed by Hatch Associates Consultants, Inc., Buffalo, N.Y. The Notice to Proceed was issued January 15, 1979 and the scheduled completion date is August 18, 1981. The project consists of two parallel rock tunnels with a minimum excavated diam of 18 ft 0 in. and a final concrete lining of 16 ft 0 in. diam. The tunnels total 14,630 linear ft. In addition to the tunnels, contract C-31 includes four shafts, an underground pump station, three cross passage connections, and other minor work items. (see Fig. 2, C-31 Project Plan and Profile) The tunnels were constructed primarily within the Bertie Formation, an approximately 50 foot thick moderately fractured to massive, dolo-

Jan 1, 1981