Search Documents

By J. C. Scully

In June, 1965, Sanderson and scully5 reported at the Conference on Environment Sensitive Mechanical Properties of Materials at the Research Institute for Advanced Studies at Baltimore that thin foils of titanium could be prepared by chemical polishing in a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. The technique is simpler than that since reported by Rice and Orava. As-received annealed titanium (containing 0.8 pct Fe and 30 ppm H) in the form of sheet 0.05 cm thick is placed in the solution and moved up and down. The reaction is violent but suitable foils are obtained very easily and consistently. A typical micrograph is shown in Fig. 3. The small precipitates were not identified. Yamane and ueda6 observed many spotlike features which they referred to as small dislocation loops. While their spots may be due to the reaction of the warm foil with the air as suggested by Rice and Orava, the precipitates in Fig. 3 are also found when foils of titanium are prepared by electro-polishing at low temperatures and subsequently examined in the electron microscope without any inter- mediate warming. Furthermore, they are not a surface effect. It is necessary to add that alloys of titanium cannot be so easily thinned by the chemical polishing solution described above since it contaminates the a, phase with hydrogen and produces y hydride. These matters are described at length in a paper7 and their relevance to stress corrosion is considered elsewhere.'-* Author's Reply The authors are grateful to Dr. Scully for bringing to our attention his hitherto unpublished technique for thinning unalloyed titanium, and deeply regret the unintended apparent duplication. The chemical thinning solution (7 parts HNO3 and 3 parts HF, by volume) reported by us is the same as that with which, for some period in the past, we had experienced success in the preparation of foils from single and polycrystalline niobium. Its subsequent effective application to titanium was a logical step, which, clearly independently of Scully, was conceived by Mr. Rice, to whom full credit is due. A few comments are warranted concerning some of the details of the preceding Discussion. It is evident to the discerning reader that the two thinning techniques under consideration are chemically almost identical, and in that sense are equally "simple". The chemical aspect is, of course, the one of primary importance in both communications. Thereafter, the relative simplicity is dictated by the mechanics of the actual thinning operation selected by the individual investigator. Our standard dimpling, or dishing, procedure was chosen with a view toward providing, for the electron transparent areas of the sample, the maximum protection from extraneous deformation during handling. That the long, straight dislocations visible in Scully's electron micrograph of a seemingly recovered structure closely resemble handling dislocations would tend to indicate the merit of our adopted technique. Features similar to those which Scully has attributed to precipitates, without any apparent diffraction contrast confirmation, were not observed in any of our clean foils taken from annealed or deformed specimens. This was admittedly somewhat surprising since the 3700 ppm (nominal) Fe in the A-70 commercial-grade titanium examined should have given rise to TiFe precipitates. Presumably these existed but were un-resolvable. Curiously, Scully's "precipitate1' density is fairly high although the iron content quoted was less than one-fourth of that in our material. One is forced to conclude from the evidence that prior thermal and mechanical treatments are responsible for the two different types of structure observed.

Jan 1, 1968

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) remains a health concern in many underground metal/nonmetal mines, and has been regulated by the Mine Safety and Health Administration since 2002. While the NIOSH 5040 standard method for DPM monitoring is required to demonstrate regulatory compliance, the FLIR Airtec DPM Monitor can serve as complementary engineering tool. It is a handheld instrument that offers near real-time measurements. As part of an ongoing field study, the Airtec has been used to survey elemental carbon concentrations (a proxy for DPM) in an underground stone mine. Via “spot-checking” and more prolonged area monitoring, this effort was aimed at determining spatial and temporal DPM variation in several key locations. INTRODUCTION Diesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It is largely made up of elemental and organic carbon (EC and OC, respectively), which can be measured as proxies for estimating mass concentrations of DPM. The National Institute for Occupational Safety and Health (NIOSH) considers DPM to be a health hazard and potential carcinogen [1]. It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition, and retention in lung tissue [2]. Since DPM exists in both the micro- and nano-particulate ranges, it can surpass typical auto-immuno defense mechanisms that keep larger particles out of the respiratory system [2]. Relative to other occupations, the DPM exposure potential for underground miners is high because these individuals work in enclosed environments where diesel powered equipment is frequently used [3,4]. A variety of engineering and administrative controls have been devised to reduce DPM exposures in underground mines, and increased airflow is often a key component of control strategies. In large-opening mines, which are most common in the metal/nonmetal sector, DPM abatement via increased ventilation can be especially complex due to moving and controlling the large air quantities [5]. The Mine Safety and Health Administration (MSHA) has regulated DPM exposure in metal/nonmetal mines since 2002. The final rule limits personal exposure to total carbon (TC, which is the sum of EC and OC) to an eight-hour time weighted average (TWA) of 160 µg/m3. To demonstrate compliance, operators must use the NIOSH 5040 Method [6]. However, the Airtec DPM Monitor (FLIR Systems, Inc., Nashua, NH) was developed as an engineering tool to provide near real-time measurements of both EC and TC for tracking personal exposures [7]. The portable Airtec works by capturing DPM on a filter and successively measuring laser extinction on the filter as DPM accumulates; the EC fraction of the DPM is dark, and so as it accumulates the filter becomes darker and absorbs more laser light [8]. The laser extinction value is directly correlated to EC, but since EC and TC are generally observed in consistent proportions (i.e., TC = EC*1.3), the Airtec is also programmed to display TC as a TWA [9]. There have been multiple studies conducted to validate the Airtec and the instrument has been adopted by some mine operators as a tool for their health and safety programs [3,8]."

Jan 1, 2016

By Boshou B

In China, there are approximately 3,000,000 million m3 of gas (methane) included in highly gassy mines liable to coal/gas outbursts; the amount of methane pre-drainage possible is estimated at 400,000 - 500,000 million m3. At present, methane drainage has been carried out in 110 mines with a total amount of 19,000 million m3 methane produced during the period of 198 1- 1986. The methane drainage in coal mines of China can be divided into three types: from adjacent seams, from working face seams and from goafs, all with good results. In recent years, general attention has been paid to integrating methane drainage into the mining system but methane drainage from old goafs has to some extent been developed as well.

Jan 1, 1988

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By Yukihito Sasaki

Sumitomo Metal Mining Co. Ltd. planned an expansion program for the Toyo smelter and refinery in order to increase the production capacity of electrolytic copper to 450,000 tpy in 2007. Regarding the flash smelting furnace, a drastic increase in the average concentrate smelting capacity from 2,300 tpd to 3,950 tpd was required to achieve the plan. It was necessary to examine the performance of the Sumitomo concentrate burner when the feed rate was considerably increased. The authors developed a mathematical model to describe the combustion phenomena in the Toyo flash smelting furnace. This model was developed incorporating the fluid flow, heat and mass transfer, and chemical reactions of the copper concentrate and ancillary fuel. The copper concentrate was considered to mainly comprise chalcopyrite (CuFeS2). The reaction of CuFeS2 was assumed to consist of two steps, namely, the decomposition of CuFeS2 and the oxidation of the resulting pyrrhotite (FeS) and sulfur (S). The combustion phenomena in the furnace at the increased feed rate were predicted using this model. It was found that the Sumitomo burner was capable of enhancing the smelting capacity. This is attributed to the wide dispersion of the concentrate particles caused by an increase in the particle mass and a long residence time in the reaction shaft; this is due to the low temperature of the reaction air. However nonuniformity of the reaction in the reaction shaft was enhanced with the increased feed rate. In order to improve the nonuniformity of the reaction, an increase in oil-burner oxygen and an enlargement of the diameter of the dispersing cone were useful. By combining the expertise of the Toyo smelter staff and the calculation results, the concentrate smelting capacity of the Toyo smelter has been stably increased to 3,600 tpd thus far, and further improvements of the smelting performance are still being carried out.

Jan 1, 2006

By Eugene Frey

"INTRODUCTION The ti taniferous-iron deposits in the Iron Mountain area of the Laramie Range, and particularly the Shanton deposit, were examined by several engineers. 3/ of the Bureau of Mines during 1942, 1943, and 1944. A dip-needle survey also was made early in 1945. 4/ Interest in this property has increased as a result of the exploratory work completed by the Bureau in 1944 on the Iron Mountain deposit, 6 miles northeast of the Shanton property.ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is due to Paul T. Allsman, chief, Salt Lake City Division, Mining Branch; James A. Marsh, district engineer; Paul E. Pesonen, Frank L. Wideman, and Frank H. Gunnell, Bureau of Mines engineers; and to S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch, for analyses of samples."

Aug 1, 1946

By Hugo Montalvão Gontijo

O complexo de extração, beneficiamento e transporte de minério de ferro denominado Minas-Rio, de propriedade da Anglo American, consome na moagem primária uma grande quantidade de corpos moedores (bolas metálicas). Recentemente, foi desenvolvido em 4 etapas um trabalho para automatizar a reposição dos corpos moedores e estabilizar o grau de enchimento do moinho. Na etapa A, com a reposição sendo realizada com auxílio de um operador. Na etapa B, com a reposição sendo realizada automaticamente de acordo com uma taxa de reposição predefinida. Nas etapas C e D, com a taxa de reposição sendo alterada por meio do sistema de controle avançado OCS-4D©, considerando a potência do moinho como indicação indireta do grau de enchimento. É possível verificar após a implementação das modificações uma maior estabilidade da potência e consequentemente maior estabilidade do grau de enchimento.

Oct 30, 2017

By A. P. Grossman

'This report was prepared by Shell Oil Company, Mining Ventures Department in accordance with Cooperative Agreement No. 14-09-0070-b53 dated September 10, 1976, between the United States of America, Department of the Interior, Bureau of Mines and C(b) Shale Oil I Project, Ashland Oil Inc., Shell Oil Company, Operator. After completion of this report the Shell Oil Company withdrew from participation In the C(b) Shale Oil Project and advised the Bureau of Minus that plans for publication of this report had also been withdrawn. The Bureau of Mines acting under terms of the Cooperative Agreement hereby releases this report for general information.

Jan 1, 1976

By Jean Igor Margem

Nestes dias materiais ecológicos como compósitos com fibras naturais em matriz polimérica estão chamando a atenção de pesquisadores científicos, devido ao seu bom desempenho na substituição de materiais como madeira, polímeros à base de petróleo e outros. Neste trabalho foram avaliadas as propriedades de tração de compósitos de matriz epóxi reforçados com diferentes espécimes de fibras lignocelulósicas. Compósitos reforçados com até 30% em volume de fibras longas, contínuas e alinhadas de malva, sisal e bambu foram testados em uma máquina Instron a temperatura ambiente. A fratura foi analisada por SEM. Os resultados mostraram alterações significativas nas propriedades mecânicas com a quantidade dessas fibras. Estas propriedades mecânicas foram comparados com outros resultados em compósitos testados em ensaio de tração. A análise da fratura revelou uma fraca interação da interface fibra / matriz, o que poderia ser responsável por um maior desempenho de algumas propriedades.

Aug 17, 2017

By Ben L. Seegmiller

The artificial stabilization of a pit slope at the Twin Buttes Mine near Tucson, Arizona has been completed as part of a practical rock mechanics program. The research program began in June 1971 as a result of the three million ton South Slope slide(1) which caused significant economic and operational problems. Hydrological studies, field and laboratory testing and investigation of various stabilization systems(2)occupied the first year of research. In July 1972 a design for an artificial stabilization test using post-tensioned cable bolts was completed and the selection of an outside contractor was made the following month. The project began in mid-September and was completed during the first week of January 1973. The test site is located adjacent to the South Slope slide in a zone of high potential failure. When the site was initially selected it was thought that it would remain stable at least until the test could be completed. However, heavy rains which fell in late October induced displacement in the half of the test site adjacent to the South Slope slide. Prior to this stabilization test it was thought both impractical as well as improbable that a moving slide could be stabilized with an artificial support system(3). Because the project was nearing the half-way point it was decided that an attempt should be made to complete the test as originally planned. This meant, in effect, that an attempt would be made to stabilize the moving section as well as the stable section.

Jan 1, 1973

By Elaynne Rohem Peçanha

Com o objetivo de estudar a interação da hematita com biorreagente de flotação (Bacillus subtilis), foram realizados experimentos de ângulo de contato. Após a interação com o biorreagente, a superfície da hematita apresentou uma hidrofobicidade apresentando um valor de 46,0º. Os experimentos de potencial zeta mostraram uma interação acentuada entre o reagente e o mineral na faixa de pH alcalina com deslocamento do ponto isoelétrico da hematita. Ensaios de microflotação foram conduzidos em tubo de Hallimond modificado, em pH 6, com uma recuperação de, aproximadamente, 80%. As teorias DLVO e X-DLVO foram aplicadas para avaliar as energias de interação entre o reagente e os minerais. As duas teorias foram capazes de prever a interação que ocorre entre o biorreagente e a hematita. Os resultados evidenciaram o uso promissor do reagente na flotação direta de hematita.

Aug 17, 2017

By A. W. Hesse

TWELVE years ago, a meeting of coal-mine operators, mining engineers, oil and gas operators, Bureau of Mines engineers, geologists and state mine inspectors took place in Pittsburgh, Pa. for the purpose of discussing, and solving if possible, the problems in connection with the drilling of oil and gas wells through or near coal mines and through the future coal reserves. Proposed regulations were drafted and presented at that meeting by 0. P. Hood and A. G. Heggem of the Bureau of Mines.1There was considerable discussion of the various articles, practically all of which appear in Bulletin 65, but unfortunately the interest aroused at that meeting was short lived. Practically none of the important coal-, producing states gave the matter the consideration it should have received at that time. REASONS FOR AGAIN RAISING THE QUESTION Notwithstanding the marked progress in, safety work, coal mines still have an unenviable reputation for mine explosions. Our mining laws have become stricter and the enforcement, especially in Pennsylvania, more sternly carried out, but what good will come from a rigid carrying out of the mining laws if some source of danger exists all around the mines, over which the operators have no control? It is hardly necessary to recite all the cases of natural-gas explosions published in Bulletin 65, but with some of them I am especially familiar. In 1912, while making one of my usual Sunday visits to the Miners' Hospital, at Fairmont, W. Va., my attention was called to a patient in a horribly burned condition. He was swathed in bandages so that no part of his face and hands were visible. He had not then been informed that his two sons, mere boys, had died of the burns they had received in the same accident. This explosion was due to natural gas leaking into a country mine at Peora, Harrison Co., W. Va.

Jan 2, 1925

By Juan Sodi, John F. Elliott

The standard free energy of ReS2 has been measured in the range of 1050° to 1250°K using H2/H2S mixtures and a slight variation of the method described by Hager and Elliott.1 The result is: The experimental method and apparatus were modified slightly for this study. Measurements on Cu2S were made to verify the application of the method to the work on ReS2. THE EXPERIMENTS AND RESULTS Briefly, the experimental method consisted of exposing a chip of copper or rhenium at a known temperature for 8 hr to a slowly flowing gas stream at the same temperature in which Ph2S and PH2 were known. The chip was withdrawn quickly from the hot furnace, and subsequently it was inspected for the presence of a sulfided surface. In the experiments described here, there was no ambiguity in any case as to the presence or the absence of the sulfide. At a given temperature, gas compositions for sulfidization were explored systematically until two compositions were found whose values of ?G°, Eqs. [I] and [2], were within approximately 100 cal of each other, one of which was sulfi-dizing and the other was not. These are termed the "straddle" compositions and it is assumed that the equilibrium composition lies between them. The chief modification to the apparatus, which is shown schematically in Fig. 1 of Ref. 1, was to support the metal specimen on a small alumina boat which could be moved along the reaction tube, 6 mm ID, by platinum wires. An appropriate seal at each end of the reaction tube permitted the sample to be moved from the cold end of the tube into the hot zone in 2 to 3 sec, and the sample could be withdrawn equally rapidly. Thus, it was possible essentially to quench the specimen from the reaction temperature with the reaction gas or helium flowing and without danger of breaking the reaction tube. The usual practice at the end of the experiment was to switch the gas system to the helium tank, flood the reaction chamber with helium, and pull the sample out of the hot zone. The purpose of the modification was to permit study of the sulfidization of copper without the complication of the back-reaction between the gas and the specimen as the latter cooled during slow withdrawal of it from the hot zone; this was a problem in the earlier work.&apos; A further improvement located the tip of the temperature-indieating thermocouple and the specimen precisely at the hottest part of the furnace. A carefully calibrated thermocouple, with its tip at the position of the specimen and with other conditions duplicating those of an actual experiment, showed that in the temperature range of 900° to 1122°C the temperature of the specimen differed from that of the tip of the indicating thermocouple by less than 0.5°C. The two positions were 0.5 cm apart. The reaction gas was prepared from ultrahigh-purity hydrogen (<l ppm O2, <0.5 ppm H2O) and CP grade hydrogen sulfide (99.5 pct H2S). High-purity helium (99.995 pct He) was used. All of these gases were purchased from the Matheson Co. All flow meters were recalibrated by the soap-bubble method with hydrogen, H2S, helium, and several gas compositions used during the study. These calibrations gave a linear relationship with a slope of 1.0 for the plot of log flow rate vs log pressure drop across the flow meter, in accordance with the Hagen-Poiseuille equation. The analysis of the gas was determined in the same manner as was reported previously. Good checks were obtained between the composition of the gas established by the flow-meter settings and by chemical analysis of the gas taken after the mixing bulb and ahead of the furnace. The pressures of H2S, H2, S2, and HS in the equilibrium gas at temperature were calculated from the following data :3 The pressures of the species S and S8 were negligible for the conditions of the experiments.3 There was no sign of vaporization of ReS2 either by weight loss or deposits in the reaction tube. Thus it is not possible to account for the apparent volatility of the compound reported by Juza and Biltz.2 The inlet gas composition and the calculated equilibrium ratio of PH2 S/PH2 for the "straddle" points of each experiment are shown in Table I. The specimens of metal for the experiment were small clippings of annealed copper (99.9+ pct) sheet 0.005 in. thick that was obtained from Baker and Adamson and of "high-purity" rhenium (99.9+ pct) sheet 0.005 in. thick that was purchased from Chase Brass and Copper Co. A specimen was removed from the apparatus; inspected for the presence of the sulfide, and then stored in a sealed vial. A fresh clipping was used in each measurement. The condition of the surface of each specimen after the experiment is noted in Table I.

Jan 1, 1969

By J Kwiri, T Zvarivadza, R Mitra, F Cawood

It is crucial to record ground movement of any magnitude to enable the safe and economical design of excavations and infrastructure. The DigiMine Laboratory is equipped with technologies to record such movements. This paper analyses the effectiveness of the Digital Mine instrumentation in recording earth movements in light of the Botswanan earthquake which occurred on the 3rd of April 2017 at 17:40 UTC. Recordings from the Digital Mine are compared with other ground sensing technologies which also captured the event (USGS and GEOFON systems). USGS and GEOFON system’s recordings suggest that, there are a number of possible mechanisms that could have resulted in the earthquake as discussed in the paper. Compared to the USGS and GEOFON systems, DigiMine system could not provide an analysis that could give possible source mechanisms. However, the system’s success in recording the Botswanan earthquake, is an indication that the system works and can be further developed or improved. For a comprehensive analysis, more data from various sensors needs to be collected. For example, DigiMine connecting to the national seismic monitoring system or to the local mine’s seismic monitoring system. Such connections will enable the development of a better self-analysis system and possibly prediction of future events. More importantly, it will contribute to better understanding of regional seismicity and its potential impact on excavation design. CITATION:Kwiri, J, Zvarivadza, T, Cawood, F and Mitra, R, 2018. How efficient is DigiMine technology in recording earth movements? A look at the Botswanan earthquake, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 414–419 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B G. Lottermoser

Field and laboratory data combined with computational modelling have been used to predict the pit water quality for the Highway Reward mine. Open pit mining of the Highway Reward copper-gold deposit has produced a final mining void with a diameter of 600 m and a depth of 280 m. This void will be left to fill with ground and surface water once pumping of pit water ceases. Several leaching tables were constructed to simulate weathering reactions and surface water run-off in the major pit wall units during a 200-day leaching experiment. To date, about three-quarters through the experiment, combined run-off from these cells has reached a pH

Jan 1, 2003

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872 R W RAYMOND 1873 R W RAYMOND 1874 A L HOLLEN 1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 ECKLEY B COXE 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882

Jan 1, 1910

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By T. Mulja, Michel Boily, Anthony E. Williams-Jones, Pierre Pilote

"The Preissac-Lacorne batholith is composed of suites of early metaluminous calc-alkalic gabbroic to granodioritic intrusives, three late peraluminous monzogranite plutons and numerous Li, Be and Ta-bearing granitic pegmatites. The Lacorne pluton is dominated by biotite and biotite + muscovite monzogranites containing abundant Be and Ta-bearing granitic pegmatites (40-80% volume). The pluton is surrounded by swarms of unzoned or poorly zoned spodumene-rich pegmatite dykes. The La Motte pluton is composed of biotite monzogranites, biotite+ muscovite monzogranites and rare muscovite + garnet monzogranites. Li, Be and Ta-bearing pegmatites are less abundant than in the Lacorne pluton and are commonly associated with molybdenite bearing quartz-muscovite-K-feldspar veins. In the Preissac pluton, muscovite + garnet monzogranites and muscovite + biotite + garnet monzogranites are the dominant rock types. The pluton rarely contains granitic pegmatites and these are generally barren. However, numerous molybdenite bearing quartz and quartz-feldspar-muscovite hydrothermal veins are observed.Li, Be andTa-bearing pegmatites display a crude spatial zonation around their parent monzogranites. Spodumene-rich pegmatites are generally unzoned or poorly zoned and are confined to the surrounding metasedimentary or metavolcanic rocks or crop out in the early gabbroic to granodioritic intrusives surrounding the monzogranites. Ta and Be-bearing pegmatites are usually concentrated towards the margins of their parent monzogranites. The highly fractionated nature ofmonzogranites (high Rb/Sr, low K?Rb, Ba?Sr, Zr/Nb ... ), their peraluminous composition (corundum normative and muscovite bearing) and the numerous occurrences of Ta and Be-bearing pegmatite dykes represent important criteria for the exploration of fertile granites."

Jan 1, 1990

By J. S. Y. Wang, R. C. Trautz

A 9-meter-long drift was constructed in the unsaturated-fractured tuff at Yucca Mountain to evaluate the potential for water seeping into an underground opening. Forty seepage tests were performed by releasing a finite volume of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations, and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2000