Search Documents

Expansion of the B.H.P. Co. Ltd. mater ials handling facilities, at their Newcastle Steelworks, began in 1964 and continued until 1970. The present complex handles the annual iron ore requirement of some three million tons for the Sinter Plant and Blast Furnaces. Iron ore is discharged from ore carriers and conveyed at rates up to 3,000 t.p.h. to either of two 180,000 ton capacity storage yards, where it is blended using boom stackers. Material is reclaimed from these yards at rates up to 1,000 t.p.h. using a slewing boom bucket-wheel reclaimer and fed to a screening station. Oversize material is scalped out and crushed in a closed circuit cone crusher. Undersize material is sized on double-deck vibratory screens which separate at 1/4in (6mm). The two fractions are blended in two of four 70,000 ton capacity blending yards using slewing boom travelling stackers. Bridge-mounted bucket-wheel reclaimers reclaim the blended piles at 1,000 t.p.h. Fine ore is conveyed to the Sinter Plant and lump ore to a second screening station, for rescreening, before passing to the Blast Furnace.

Jan 1, 1972

By V. J. Hucka

Coal, which was discovered in Utah in 1849, covers about 18% of the total area. Production in 1981 vas more than 14 million tons. However, some Utah coal mines are quite gassy. If longwall face technology is applied, then a release of a high volume of methane may be expected during the mining process. Investigations on methane content have been made by use of an isothermic bubble desorbometer. The desorbable methane content of 5 m3 to 16 m3 of methane per ton of coal mined has been determined.

Jan 1, 1983

Discussion of the paper of N. V. Hansell, presented at the Cleveland meeting, October, 1912, and published in Bulletin. No. 72, December, 1912, pp. 1497 to 1,517. F. L. GRAMMER, Leesburg, Va. (communication to the Secretary*).:-Mr. Hansell conies from a country where charcoal is the fuel, and fuel is therefore costly. The Swedes appreciate more than most Americans the value of ore-concentration, not only in fuel-economy, but also in its influence on the quality of metal produced. Neither in these particulars nor in our knowledge of the dressing of iron-ore do I think. we can claim to be their equals. A 60 per cent. ore is not merely- twice, but more than four times, as valuable as an ore carrying 30 per cent,. Failure to appreciate this fact explains many idle American stacks, erected in defiance of it. Next to the rule that the equipment-cost of a blast-furnace increases approximately as the square of the hearth-diameter, I know of no mathematical relations involved in smelting iron which are less appreciated than the disadvantages of lean ores. Mr. Orn told me, when I was in Stockholm, that 2,500 patents on magnetic concentration had been taken out. He may have been joking as to the exact figure, but his remark indicated the great activity of inventors in this field. The magnetic separators seem to represent two main ideas, namely, wet and dry separation. The wet separators, such as the Gröndal, are applicable to ores requiring the greatest comminution by reason of the small particles of associated minerals or because of the occurrence of magnetite with a soft mineral likely to cake, as in those of Cornwall, Pa. Of the dry magnetic separators some are well suited for large-grained ores, such as those of Mineville, N. Y. We have also magnetic separators, like the Wetherill, for ores not usually classed as magnetic.

Jan 5, 1913

By E. C. Robertson

Observations of faults in mines, at outcrops, and in the laboratory lead to the conclusion that the displacement d of a fault increases irregularly but monotonically with the thickness t of its associated fault gouge and breccia, not including adjacent undisplaced jointed rock. The general trend of data points has a slope d/t of about 100. (The correlation coefficient of a logarithmic regression line is r = 0.94.) The rather wide scatter of the points can be accounted for by inaccuracies in measurement of d and t, and by variation in the conditions at faulting of confining pressure, rock type, water pressure, and deformation history. Limestone is an exception to the relation. Until the data can be corrected and refined, the relation should be used only qualitatively for estimating displacement of ore bodies in mines. The suggested relation is based on observations of 48 steeply- dipping normal and reverse faults and nine small flat-dipping thrust faults, with displacement less than 5 km (3 miles). It does not apply to large strike-slip and low-angle overthrust faults because their large displacements are poorly determined and their breccia thicknesses are widely variable.

Jan 1, 1984

By Charles Wurms, Robert Steinitz

DURING an investigation to determine the compatibility of several metals with tungsten, the degree of reaction between tungsten and lead was determined. A literature survey showed considerable disagreement between the results of various earlier investigators. Information presented by M. Hansen1 states that, according to S. Inouye,2 tungsten has very poor resistance against attack by molten lead, even at the low temperature near the melting point of lead. A phase diagram in the same reference indicates a solubility of 30 wt pct W in molten lead at 1300°C. Contrary evidence was shown by Parkman and shepard3 in their investigation of materials for use in heat transfer systems containing liquid lead alloys; they performed experiments at 980°C for times up to 50 hr without noticing any appreciable attack on the tungsten. Tungsten sheet was immersed in molten lead contained in Vycor tubes evacuated to at least 10-4 mm Hg. R. Bernard4 and R. I. Jaffee5 also indicate that no reaction occurs between molten lead and tungsten. However, no experimental data were included in these reports. In order to settle the question of the solubility of tungsten in molten lead, tungsten powder with an average Fisher subsieve particle size of 6µ was pressed in a double-acting die at 6 tsi to small compacts. They were then sintered in an atmosphere of hydrogen for 2 hr at 1700°C, resulting in a sintered density of 64 pct of theoretical with final dimensions of 0.260 in. in height and 0.245 in. in diameter. For all tests, the tungsten pellets were immersed in molten lead. Table I is a summary of the experimental procedures showing atmospheres, temperatures, and times. The first experiments were performed at 650°C; at this temperature, the liquid lead should wet the porous tungsten better than at its melting point, and penetrate into the pores. The lead was heated in a graphite crucible with a graphite cover. No protective atmosphere was used, as it was expected that the formation of CO would be sufficient to prevent oxidation. This, however, proved to be wrong, and all tungsten samples showed a slight oxide film after treatment. The tungsten samples were immersed in the molten lead for times of 5 min, 10 min, 1/2 hr, 1 hr, and 2 hr. After this time, the melt was poured into a form and the

Jan 1, 1962

By J. F. Barkley

"The fly-ash problem of the smoke-abatement engineer - who now might well be titled, ""Smoke and Fly-Ash Abatement Engineer"" - starts with the necessity for him to know what fly ash really is, what plants really create it, and how much is being created. Fly ash in this connection may be defined as all solid particles emitted to the atmosphere as a result of the combustion of fuel.COMPOSITION OF FLY ASHMuch can be learned about fly ash by studying samples with a strong magnifying glass or, preferably, a high-power microscope. As an example, figure 1 is a photomicrograph of an underfeed-stoker fly ash weighing 23.7 pounds per cubic foot, which passed a baffle-type cinder catcher and was caught by a Cottrell precipitator. Figure 2 shows a similar fly ash made at a higher stoker rating and weighing 36.2 pounds per cubic foot. The lighter ash contains more light, unconsolidated ash than the heavier. In both instances some of the ash has been fused to a glass, as is indicated by the spherical particles resembling marbles; however, the heavier dust contains more and larger spheres. With the faster burning and higher air pressures occurring at the higher burning rates, more of the larger fused spheres reached the precipitator.Such studies of fly ash frequently make possible correct determination of its source. For example, the Supreme Court Building, one of the finest of the Federal buildings in Washington, was having considerable difficulty with fly ash from some outside plant. It was thought to come from a nearby apartment house. A fly-ash trap was installed there, and care was taken in the operation of their underfeed stokers. The fly-ash nuisance continued. Microscopic examination of the fly ash found about the building compared with samples taken from the stack of the apartment house showed to the surprise of the accusing building superintendent that the present source was elsewhere. By the same means, the source was found to be a plant about ore-half mile away."

Sep 1, 1939

By G. R. Belton, Y. K. Rao

A galvanic cell, using liquid MgCl2 or MgC12-CaC12 mixtures as the electrolyte, has been used to determine activities in Mg-A1 liquid alloys between 700' and 880°C. The incovporation of a chlorine electrode in the cell also allowed measurements to be made of the standard free energy of formation of MgCl2(l). The results are shown to be in good agreement with thermo-chetrlical values from the literature, and this is taken as evidence that the small, known solubility of magnesium in iMgCl2 introduces no significant error in galcanic cell measurements. Within experimental error, the activity coefficients and relative partial molar enthalpies at 800°C are shown to be represented by the following "subregular" solution equations: logy~~ =-0.68(1 -xMgj3 log yAL =-1.02(1 - XMf + 0.68(1 - XMf H.M = -4400(1 - %)3 / cal Mg 7Ag' HZ =-6600(1 - xA1)' + 4400(1 - XMf cal SCHNEIDER and toll' have used a transpiration technique to measure the vapor pressures of magnesium over Mg-A1 alloys between 544" and 594°C. amsstad,' however, has since suggested that the extrapolation to zero flow rate, used by these authors in interpreting their apparent pressure vs flow rate data, gives unreliable results. Rogers, Tomlinson, and Richardson,3 in interpreting the results of solution equilibria between Mg-A1 alloys and liquid MgC12, also considered the measurements of Schneider and Stoll to be unreliable and preferred to derive activities for the alloys from the earlier boiling point determinations of ~eit~ebel~ and the partial molar heats recommended by Kubaschewski and ~atterall.~ These latter heats were based substantially on the early calorimetric work of Kawa-kami but, unfortunately, his work on other systems has sometimes been found to be inaccurate.7 Rogers et al., in the above-mentioned paper,3 tentatively concluded that the most likely species responsible for the limited solubility (0.3 mole pct at 800°C) of magnesium in MgC12 were Mg° (neutral) and Mg2++. Two more recent studies8,9 have supported Mg2++ as the soluble species. In the present study, activities in Mg-A1 alloys have been determined by means of a galvanic cell involving liquid MgCl2 or MgC12CaCl, mixtures as the electrolyte. Since the reactive nature of magnesium precluded simple Faraday yield experiments, a chlorine electrode was incorporated in the cell in order that the performance of the cell could be checked by measurements of the heat and free energy of formation of MgC12. This procedure was considered necessary since it has been suggested1' that the solubility of a metal in a molten salt might introduce electronic conductivity; also, previous determinations of the standard electrode potential for MgC12 differed by as much as 70 mv11-13 EXPERIMENTAL Materials. Analyses of the materials used in preparing the alloys and the electrolyte mixtures are presented in Table I. The alloys were prepared by induction melting weighed amounts of the metals in a graphite crucible held under an argon atmosphere. Pure anhydrous magnesium chloride was prepared by heating the mixture MgCl, . 6H20 +NH4C1(1:1) to 650°C, followed by melting under dry argon. The melting point of the dry MgC12 was found by differential thermal analysis to be 714.8oC, which compares well with the accepted value of 714C.14 This agreement was taken to be an indication of the high purity of the dried salt. Table I. Compositions of Materials, wt pn Impurity Mg Al MgCI2 CaCI, Ba - - 0.005 Ca - - 0.010 Cu 0.02 0.02 Fe - 0.10 0.001 0.010 Pb 0.01 - 0.001 0.005 Mn 0.15 0.001 Si - 0.10 Sr - - 0.005 MBSO* - 0.040 ARGON TUNGSTEN CHLORINE LEAD—411 11 II ALUMINA 'A I / ave GRAPHITE on irA~_ ( ^"l ROD MAGNESIUM S>ILICA~^ /, OR ALLOY-. I /A] ___________ -«^- _ ELECTROLYTE I y FRITTED DISCS Fig. l—Arrangement of chlorine and metal electrodes in electrolytic cell.

Jan 1, 1970

By William Gleason

Since 2004, Dave Kanagy has served as the executive director and chief executive officer of SME. In that role, he has worked with 22 SME Presidents, traveling the world to represent the Society. His prestigious one-million-mile status with United Airlines is a testament to these efforts. He has been to six of seven continents while leading the Society on a journey from a struggling association in 2004 to the largest and arguably the most influential professional mining society in the world. In the following pages, some of those past SME Presidents reflect on their time with Kanagy and paint the picture of a visionary leader who was willing to make the hard decisions for the betterment of the Society while remaining open to new ideas and opportunities. One of his first accomplishments as the executive director was to streamline the SME Boad of Directors from 29 members to nine, making it much more effective. With a keen financial sense, he was able to add value while cutting excess to expand the Society in every measure. As the leader of SME, Kanagy helped facilitate much of the Society’s growth and innovation as the world’s largest mining related organization. He has a B.S. degree in industrial education from the University of Maryland, an M.S. degree in technology education from Eastern Illinois University and is a certified association executive by the American Society of Association Executives. Under his leadership, several unique programs were created or advanced, including OneMine.org, the world’s foremost online mining research library. He enhanced legacy programs and increased collaboration with international organizations. Kanagy is the recipient of prestigious awards, including the Colorado Society of Association Executives’ Professional of the Year award and the Mining and Metallurgical Society of America’s Gold Medal award.

Feb 1, 2026

I have headed this paper with a question and for the impatient among you ûthe answer is no we have not run out of developments but, and it is a big æbutÆ, we need to be innovative and ahead of the game or ænoÆ will be æyesÆ before we know it.Why do I believe that our future lies in innovation? Thirty years ago, knowledge doubled every 14 years. It is now doubling every seven years. In 1965, Gordon Moore, one of the founders of the chip maker Intel, made an observation that growth in memory chip performance is doubled every 18 months which became known as MooreÆs Law. Now there is fibre law, where the transmission line capacity doubles every nine months and storage capacity, under disc law, doubles every 12 months. What does this mean? Well, firstly there is a massive rise in information flow and availability with no limits in growth for at least the next ten years. Secondly, unlike our grandfathers, we are most unlikely to be employed by the same firm for our working career - we may not even have the choice to stay with the same company. In a phenomenon Richard Foster and Sarah Kaplan (2001), borrowing from Schumpeter, termed æcreative destructionÆ, companies are unable to sustain market-beating levels of performance for more than ten to 15 years. In the 1920s the turnover rate of companies in the United States was 1.5 per cent, so a company could employ almost three generations from the one family. A company had a half life of 60 years. In other words, you could well be in the same working environment as your grandparents. Today the churn rate is estimated to be eight to ten per cent. A company has a half life of five to six years. So for large companies, as an employer or employee or as a contractor, your working environment has a 50 per cent chance of changing in five years. Innovation is the driver of this rapid rate of change. Innovation is not for the faint hearted (Cutler, 2001) but it is the core for success in the global economy. The rate of change in our world is not going to decrease. We must learn, not only to manage change, but to enjoy the process of changing û to ride the tsunami of the knowledge economy.

Jan 1, 2002

By Apoorva Bajaj

Iron ore mines of Steel Authority of India Limited (SAIL) have to comply with strict chemical composition norms laid down for iron ore lumps supplied to its steel plants. This requires a careful planning of the overall ore excavation operation. In general terms, the problem can be stated as: Given the chemical composition of ore for all excavation sites, excavation capacity of each shovel, distance of each excavation site from the crushing plant and the number of dumpers available for transport of the ore, find out the percentage of ore to be excavated from each excavation site such that the production rate is maximized and the chemical composition norm is satisfied to the best possible extent. This paper presents an approach to solve this problem using Branch and Bound method. The specification for r.o.m. quality has been modified by incorporating a new parameter, ?Al2O3 / SiO2? ratio, which has a significant effect on the performance of iron blast furnace.

Oct 1, 2009

By Flávio Paulo Pugnal da Silva

Em 2010 foram observados elevados índices de quebra de rolamentos dos segmentos da máquina de lingotamento contínuo 3 da ArcelorMittal Tubarão. As análises iniciais, realizadas pelo fabricante, sugeriram que a causa estava relacionada principalmente a falta de proteções térmicas e desvios no sistema de lubrificação que estavam deteriorando as propriedades físico-químicas da graxa. Após o restabelecimento das condições de projeto os índices de quebra mantiveram-se elevados. O objetivo deste trabalho foi avaliar as potenciais causas ligadas as falhas de lubrificação deste equipamento. Foram estudados temperatura de trabalho do equipamento, qualidade físico-química da água, vazão e velocidade da água de refrigeração dentro dos mancais e respectivos suportes. Os resultados obtidos convergiram para uma deficiência do projeto de resfriamento dos mancais e suportes. Tais deficiências geravam baixa velocidade do fluxo de resfriamento, que associada as altas temperaturas de trabalho, proporcionavam condições adequadas a precipitação de particulados contidos na água, gerando assim a obstrução gradativa dos canais de refrigeração até total colapso do sistema.

Jul 30, 2018

By J. B. Wagner, p. Hembree

The iron tracer diffusion coefficient of umstite has been measured at 110(fC across the phase field and at a single composition at 800°C. Assuming a simple cation vacancy model the tracer diffusion coefficient was found to be a linear function of the cation vacancy concentration at 1100°C. The equation is D = 3 x 20 29 where denotes the concentration of vacancies in numbers per cc. The tracer work at 800°C was carried out to investigate the reported "pinning" of tracer to the wustite surface at low temperatures. No evidence for the "pinning" of the tracer was found at 800°C in COz-CO gas mixtures. HIMMEL, Mehl, and Birchenall,&apos; Carter and Richardson,2 and Desmarescaux and La combe3 have measured the diffusion of iron tracer in wustite at several temperatures and compositions. The present work was undertaken to extend the measurements over a large composition range at 1100°C and to resolve certain apparent discrepancies in the data, expecially at lower temperatures. EXPERIMENTAL Wustite was prepared by oxidizing rectangular iron plates* in C02-CO mixtures. The samples were •The iron was supplied by the Battelle Memorial Institute courtesy of the American Iron and Steel Institute. The analysis is presented in Table I. quenched. Due to the inward flow of cation vacancies during oxidation, the center of the sample contained a thin void. The edges of the wustite slab were sanded until the sample could be split into two parts. Each part was then sanded on the front and back flat area until a smooth surface was obtained. The specimens were then replaced in the furnace and equilibrated at llOO°C in a predetermined COa-CO mixture by methods described elsewhere.4"6 The specimens were again quenched and the surfaces were lightly sanded to remove any roughness following the first equilibration. The specimens were then reequi lib rated in the same C02-CO mixture for thirty minutes in order to relieve any mechanical damage on the surface due to the polishing. The specimens were then quenched and the tracer was applied by an electroplating technique. The work of Carter and ~ichardson&apos; demonstrated that there was no systematic difference in the iron tracer diffusion coefficient in wustite if the tracer was plated, dried, or evaporated on the specimen. In the present study a piece of filter paper was saturated with an iron chloride solution of pH <* 3 that contained the tracer FeS5. The wustite was placed on the filter paper and made the cathode. A current density of 0.4 to 0.6 ma per sq cm was passed for about five to ten minutes. The thickness of the tracer layer was estimated to be about 7 x lom6 cm. This estimate was made by considering the area plated, the current flow, and time for plating and the activity of the iron in the plating solution. Different areas of the specimen were counted using a collimator to determine the uniformity of the tracer. Any specimen which exhibited a variation from the initial count rate (about 1500 cpm) by more than 15 pct was rejected. An estimate of the time necessary to convert the thin layer of iron tracer to wustite was made using the data of Pettit and wagner." he estimated time was 1 sec at 1100°C assuming linear oxidation kinetics. The shortest diffusion anneals were 1800 sec. The samples were suspended in the hot zone of a furnace by two platinum wires. Two separate specimens were run at the same time. Only the edges of each sample were in contact with the wires. The C02-CO gas of the same composition as that used in the pre-diffusion anneals flowed freely around the samples at a linear velocity of 0.9 cm per sec. To initiate a run, the specimens were lowered from the cold zone of a furnace to the hot zone by a magnetic lowering device." bout 60 sec were required for lowering. To terminate a run, the sample was withdrawn from the hot zone to the cold zone. Time zero for the beginning of the experiment was taken when the sample blended into the red glow of the furnace and conversely for the end of the experiment. The surface decrease method of measuring the tracer diffusion coefficient was used to collect the data. This method requires that counting geometry be reproducible because the specimen is counted before the diffusion anneal and after the anneal. A special jig was constructed for each specimen so the specimen could be removed from the jig and returned to the jig such that the well geometry was reproducible.

Jan 1, 1970

By Alfred Boyles

"Heredity"1 in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mechanism of freezing in cast iron. The experiments described below are largely concerned with that problem. Normal and "Dendritic" Cast Iron As examples of variation in type of structure, photomicrographs of two test bars of cast iron are shown (Figs. 1 and 2) and the composition and properties are given in Table 1. Both are common, unalloyed gray iron. Test bar No. 13 has normal graphite flakes while No. 49 has very fine, lacy graphite arranged in a dendritic pattern, the matrix in both being pearlite. These two types of cast iron are well known to foundry-men and need no detailed description.

Jan 1, 1937

By Simón D. Strauss

El presente estudio revisa la evolución de la producción de los principales minerales (plomo, cobre y plata) en Estados Unidos desde la década del 70, asi como su repercusión en Chile, Perú y algunos países latinoamericanos. En esta perspectiva, se pronostican algunos datos sobre los cambios políticos, sociales y económicos que ocurrirán dentro de los próximos 28 años y que afectarán la demanda de productos minerales y la capacidad para producirlos.

Nov 20, 1972

By R. Dawson Hall

WHAT are the opportunities for the services of engineers in the coal mines? The best answer perhaps can be made by detailing the present lines of development in the bituminous coal mining regions. They are just at the beginning of a period that can be conservatively termed revolutionary. A few glimpses of new possibilities in economic mining that will reduce the cost of bituminous coal at the mines by at least one half have convinced almost everyone that a change must shortly come about. The cost of housing has become such a burden, especially in mountainous regions, that development which demands the hiring of more men and constructing more houses would not be profitable. The introduction of mechanical aids to mining, transportation and dumping suggests a way of obtaining a large tonnage with the same or a smaller number of men with no further house construction. At the same time the restriction of immigration has made it increasingly difficult to obtain men inured to hard labor. Modern civilization is not productive of muscular energy and at the same time it provides men who are not indisposed to the use of the mental effort required to direct the physical forces now available for the replacement of such energy.

Jan 1, 1924

By K. P. V. Lei

The Bureau of Mines investigated molten salt electrorefining &apos;n helium atmosphere cells as a means for the production of ductile vanadium. &apos;Electrolytes composed of NaCl-VCl2, LiCl-NaCl-VCl2, BaCl2-KCl-NaCl-VCl2 KCl-LiCl-VCl2, and CaCl2-NaCl-VCl2 were tested. Two electrolytes, KCl-LiCl-VCl2 and CaCl2-NaCl-VC12, were selected for laboratory-scale production tests. A molten salt electrorefining process was developed for the production of ductile 99.6 percent vanadium from a commercial 90-percent grade. Using the CaCl2-NaCl-VC12 electrolyte, an 87-percent recovery of ductile vanadium was made; an 85-percent recovery was made with the KCl-LiCl-VCl2 electrolyte.

Jan 1, 1967

By J. Herbst, K. Fallenius, G. Poling

Since 1970 a new series of pneumo-mechanical flotation machines has been developed by Outokumpu Oy. The cells have a completely new type of mechanism based on a recently-developed theory of conditions necessary for dispersion of large amounts of air. The mechanism was developed in 3 cu m cells and scaled to 16 cu m cells. Rotor and stator description, scale-up theory, and practical experience with the 16 cu m cell are presented.

Jan 1, 1976

By Tae-Hyun Kim, Kang-In Rhee, Jeong-Soo Sohn

The synthesis of Mn-Zn ferrite powder from spent zinc-carbon batteries was investigated using a series of physical treatment, sulfuric acid leaching and coprecipitation. Physical separation methods such as crushing, magnetic separation and sieving were applied to generate a non-magnetic material of 8- mesh undersize for subsequent leaching process. The 8-mesh undersize of the spent zinc-carbon batteries was assayed 23.9% Mn, 14.9% Zn, and 4% Fe. Metal extractions obtained in sulfuric acid leaching at the solid/liquid ratio of 1:10, 2 M H2SO4, and 60? with 6 vol.% H2O2 addition were 97.9% Mn, 98.0% Zn and 55.2% Fe. The leach liquor was finally adjusted to the Mn:Zn:Fe mole ratio of 1:1:4 suitable for producing MnZnFe4O8 ferrite powder by the addition of Mn, Zn and Fe sulfates followed by pH control. A co-precipitation test for Mn-Zn ferrite powder was performed at 80?, O2 gas flowing at 1.3 L/min. As a result of co-precipitation, Mn-Zn ferrite nanoparticles in 20 nm size with spinel structure were successfully synthesized. The saturation magnetizations of Mn-Zn ferrite powder (Mn1-xZnxFe2O4) were determined to be 39-91 emu/g with various zinc contents (X=0.2-0.8).

Jan 1, 2008

By Camila Fernandes Rezende, Camila Simon Christ, Vinicios Andreatta, Marcus Vinícius Pimentel Gomes

A integração e cruzamento de dados de diversos sistemas para as unidades técnicas de processo sempre foi uma necessidade e um desafio. Para a unidade técnica da Aciaria, a integração de dados gerados pela Instrumentação, Automação e MES (Manufacturing Execution System) é imprescindível para a análise e otimização do processo. Este processo feito de forma manual era trabalhoso, improdutivo e com grande potencial de erros. Mesmo com o suporte da área de TI (tecnologia da informação) e TA (tecnologia de automação), em alguns casos este processo era inviável devido à complexidade. Com a utilização de uma ferramenta analítica, já utilizada em outros processos produtivos da empresa (Laminação de Tiras a Quente e Qualidade), foi possível prover acesso a diferentes bases de dados, permitindo a integração dessas informações de forma simplificada, ágil e única, todos consumindo os mesmos dados, com as mesmas regras. A automatização deste processo trouxe benefícios como: melhora na qualidade do dado, democratização das informações e tempo para investigação de problemas e otimização de processo, além de menor dependência das equipes de TI e TA.

Oct 1, 2019

By A. G. Spencer

"The horsepower required to drive large grinding mills has increased dramatically during the past ten years. Limitations on the amount of power which may be transmitted by a single gear and pinion have resulted in the application of multimotor drives, with consequent loadsharing problems. It has also sparked the development of some entirely new drive concepts. In addition, the severe demands made upon the electrical system during the acceleration period have required that the selection of motors and electrical system design be closely coordinated. Moreover, the installation of such large process units results in downtime being very costly. The equipment selected and the plant maintenance philosophy must therefore be such as to minimize the risk of unscheduled downtime."

Jan 1, 1972