Search Documents

By Nightingale R, Johnson B, Bensley C, Vince A, Keast-Jones R

In order to counter the massive increase in the level of near gravity material that would follow the reduction in dense-medium cyclone separation density at B.H.P. Slab and Plate Product Division's B and C coal preparation plants, "wing tank" systems to control medium density to within ¦0.005RD units have been installed. However, despite very precise density control, cyclone metallurgical performance has been less than satisfactory. The approaches taken to identify the causes of this poor performance and to justify alterations in operational and maintenance practices are presented.

Jan 1, 1987

By J. Silva, M. Kotraba, F. Pontanilla

Blasting is the application of highly complex science that, in some cases, could be viewed as an art. Many variables are involved in a blast, including geology, pattern design, timing and firing sequence, and explosives selection. Assuming that better results can be achieved by only increasing the powder factor is inaccurate. The Drill-to-Mill (D2M) concept has been in the mining industry for over two decades. The D2M approach is commonly viewed in an oversimplified manner, assuming that by simply increasing drilling and the amount of explosives used (both of which add operational costs), the downstream value will be created. An optimized D2M initiative should combine the smart application of explosives at the beginning of the mining process, matching the dynamic properties of the rock to the explosive selected to improve the efficiency of the energy created by the explosive to the rock mass being blasted, and to bring benefits to the mining operation across the entire mining and processing value-chain. This paper reviews the principles behind matching the shock impedance of the rock and the explosive and compares the traditional use of explosives versus the smart application for two hypothetical blasts.

Jan 1, 2024

By Jose A. Ruiz

INTRODUCTION For heterogeneous non-catalytic solid-gas reactions carried out in fluidized bed reactors, nominal bed temperature is an average value between gas and solid. For highly exothermic reactions, actual particle temperature can be up to hundred degrees above termocouple temperature, since heat dissipate at slower rate than heat generation during some steps of transformation. These micro instabilities at particle level can displace thermodynamic equilibrium from the desired phase to others. This effect is important when relatively narrow range of phase stability exists, like in sulphation roasting of sulphides, where bed discharge contains, in addition to the desired sulphate others metastable phases such as basic sulphate and ferrite. For example, for copper-iron sulphide concentration roasted below 680°C, no cupric ferrite is formed, as shown by Jakob et al., therefore the separate Kellogg's stability phase diagrams Cu-S-O represent the roasting (Fig.l). At temperature above this one, like 760°C for example, phase stability changes from CuSO4 to the basic sulphate Cu0•CuSO4. Solid state reaction between Cu0•CuSO4 and Fe203 also occurs to form cupric ferrite, Cu0•Fe2O3, therefore the Cu-Fe-S-O Kellogg's phase diagram of Fig. 1 (continuous line) represents this condition of roasting. Although both Cu0•CuSO4 and Cu0•Fe2O3 are metastable phases under normal operating conditions of sulphation roasting(1-10% SO2, 1-10% 02 and 680°C, points A and B,Fig. 1) sulphation of these species and particularly ferrite are slow and limited due to diffusional control. This explain why reactors discharge contains several phases: CuSO4, Cu0•CuSO4, CuO•Fe203 plus small amounts of CuS and FeS due to the baclonixed conditions of fluidized bed reactors. The presence of cuprous ferrite due to reducing conditions inside individual particles also occurs, but in very limited extent at the reaction interface, as it is demonstrated by the low soluble iron levels of calcines. On the other hand, the presence of cupric ferrites can be explained only due to the higher temperature achieved by particles, since below 680°C cupric ferrite formation does not take place. [ ] This phenomena also occurs for others non-ferrous metal sulphides concentrates roasted under sulphation conditions, such as 7n, Co and Ni. Therefore the prediction of discharge composition of fluidized beds is not possible based only on kinetics and mechanistics models alone or purely thermodynamical considerations, since all factors should be integrated to describe the overall phenomena. SINGLE PARTICLE TRANSFORMATION Assuming a first order reaction with respect to the gas and zero for solid, such as

Jan 1, 1984

By A. D. Davis

The disposal of spent ore from cyanide heap-leach processing facilities is of concern to the mining industry, regulatory agencies, and the public. Disposal of several hundred million tons of additional spent ore is planned in the western United States during the next decade, with increased amounts likely if gold prices rise. In the past decade, more than fifteen million tons of spent ore have been disposed of in the Black Hills. South Dakota's off-loading criterion for cyanide has been set by the state's Department of Environment and Natural Resources at 0.5 parts per million (ppm) as weak acid dissociable (WAD) cyanide. Nitrate off-loading limits vary for each mine in the state, depending on ore type and other factors. Nitrate concentrations in leachate from spent ore depositories could be caused by conversion from other nitrogen-containing species. One likely source of nitrate is residual explosives from blasting of ore. Previous work on the combustion products of nitrogen explosives has shown incomplete 3xidation (Johansson and Persson, 1970). Another likely nitrate source is degradation of cyanide to ammonia, followed by oxidation to nitrite and nitrate.

Jan 1, 1994

By Garland R. Dever, Preston McGrain, George W. Ellsworth

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. High calcium and high carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental control measures, and other special uses are present in the High Bridge Group (Ordovician) and Warsaw and Ste. Genevieve Limestones (Mississippian). Deposits with thicknesses of 7.3 to 20.7 m,(24 to 68 feet) have been documented by the analysis of samples taken at 0.3-m (1ft) intervals. Active and potential mine and quarry sites afford access to water transporation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1979

By R. K. Singhal

A sizable surface mining industry exists in Western Canada. There are the surface coal mines in the provinces of Alberta, British Columbia, and Saskatchewan producing the bulk of Canadian Coal. The two oil sands plants in Fort McMurray, Alberta producing synthetic crude oil are surface mining operations. Much of the metalliferous mining in British Columbia is carried out by open pit methods. This paper discusses the current surface mining methods in both of these industries with particular reference to Alberta. Issues relating to environmental impact assessment, mine reclamation and mine site closure have been dealt with.

Jan 1, 1995

By S. F. Walsh

The San Manuel Oxide Pit is located within the subsidence boundaries of Magma Copper Company's block caving operation. Ground conditions offer a constant blasting challenge and vary from hard, competent crystalline rock to widely spaced fracturing in a sedimentary conglomerate. A successful drilling and blasting program has undergone several changes since mining commenced in 1985 and continues to be developed. This paper discusses the site specific progress made with the drilling and blasting program from selection of feasibility parameters to current practice. Topics discussed include controlled blasting, use Of high energy blasting agents, charge decking, blast casting, as well as standard drill and blast techniques.

Jan 1, 1988

By John G. Reid

When the paper "Operations at the Greenvale Nickel Project Mine and Refinery" was delivered at the 1st International Laterite Symposium in February 1979, the Yabulu Caron plant had been operating for four years and production had just stabilized. The design had been based closely on the Caron plant at Nicaro, Cuba, built in 1944, also by Freeport. Yabulu had 10 Herreshoff ore roasters and production in 1978 was 18,682 tonne nickel as impure oxide sinter and 763 tonne cobalt in a mixed sulphide with a cobalt to nickel ratio of 1 :2.5. In the 25 years since the 1st Symposium, two more roasters have been added, but dry ore processing rate has remained relatively unchanged at 2.4M Uyr to allow a lower feed rate per roaster with associated higher recovery. The ore source has changed from the domestic Greenvale mine to imports from New Caledonia, Indonesia and the Philippines. Nickel production between 1978 and 2003 has risen by 67%, cobalt has risen by 146% and the products have changed to high purity nickel compacts and "ChemGrade" cobalt salt. The plant changes that have contributed to the increased recovery, production and product value are discussed. Keywords: Caron, Yabulu, nickel, cobalt, ammonia

Jan 1, 2004

By W. Jacobi, K. Eisfeld

The primary objective of dosimetric modelling for the inhalation of radon daughters is the evaluation of the dose distribution and of the mean dose to sensitive cells or target tissues in the respiratory tract which are assumed to be responsible for the initiation of lung cancer. The results of such dosimetric models are influencing the practice of radiation protection in a twofold manner: Firstly, they enable us to identify appropriate operational quantities for air monitoring and for the surveillance of individual exposures to radon daughters. Secondly, they can be used to derive secondary and operational limits for these radionuclides from the basic dose limits. The dose to target tissues in the lung from inhaled radon daughters depends on various physical and biological parameters: The unattached fraction of daughter atoms, the AMAD of the carrier aerosol for attached atoms, the geometry of the respiratory airways, the breathing conditions, the parameters for the retention and translocation of daughter atoms in the different lung regions, and the location of the target cells or target tissues, respectively. Therefore, dosimetric modelling for radon daughters has to include a sensitivity analysis showing the influence of these parameters. To meet these objectives we have recently described in a comprehensive report an improved dosimetric model for the inhalation of 222Rn, 22ORn and their short lived daughters (Jacobi and Eisfeld, 1980). In the following this model is shortly described and the main results are summarized. DOSIMETRIC MODEL [Model Structure]. For the geometry of the bronchial airways the model A of Weibel (1963) was used. Each bronchial generation i (i =0.1 .... 16) was considered as a separate compartment i, for which the following transfer pathways for radon daughter atoms were taken into account (see fig. 1): (1) the uptake by deposition (deposition probability wi); (2) the translocation by ciliary clearance (rate constant [A]i); (3) the transfer to blood by diffusion through the bronchial epithelium (rate constant [A]b). To distinguish between attached (Index a) and free (index f) daughter atoms each bronchial generation was divided in two subcompartments (i.a and if) with a transfer rate constant [a]s (ia- if) characterizing the desorption or dissolution rate of attached atoms in the mucus fluid. Thus for daughter atoms primarily deposited in attached form the transfer to blood is a twostep process with the rate constants [a]s and [A]b which were assumed to be independent of the generation number i. [Deposition]. The deposition probabilities wi in each bronchial generation were calculated on the basis of the laminar diffusion model of Gormley et al. (1949); however the deposition in the upper airways was corrected for turbulent air flow, taking into account the results of our deposition experiments (Martin et al., 1972). Figure 2 shows the resulting deposition probabilities per unit surface area of the bronchial generations for nose breathing at a rate of 20 1/min. The values for attached daughter atoms refer to an AMAD of 0.2 - 0.3 µm ([O]g =3) for the carrier aerosol; the deposition values for free atoms were derived with a diffusion coefficient of 0.05 cm2/s, assuming a prefiltration of 50% in the naseopharyngeal region.

Jan 1, 1981

By Magnus Ek

After the installation of three new converters as part of the recent expansion of the Rönnskär smelter completed in 2000 work continues to further improve the converter operation. The converter upgrade led to an increase in blister copper taps from 150 tons per batch to more than 300 tons. The total cathode copper production increased from 130,000 tons in 1999 to 230,000 tons in 2001, the first year in full production. In recent years focus has been to improve operating practise, maximize the blowing time, extend the converter campaigns hence to reduce the specific brick consumption and improve the converter slag composition.

Jan 1, 2005

By William H. Schiffbauer, Ph. D. Mowrey

Proximity warning devices can improve workplace safety by alerting workers when they are in a hazardous area near moving equipment. Industrial work sites often present extreme challenges to safety-based proximity warning devices. Many commercially available types of proximity warning sensors and systems can be rendered useless when covered with mud, ice, snow, ore, rock, and other material. The list includes radar, ultrasonic, capacitive, and visual types of sensors and systems. Addressing these shortcomings, NIOSH personnel have developed a patented active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) which employs lowfrequency, low-power magnetic fields which are quite impervious to severe environmental conditions. A shapeable wire loop antenna which provides the marker of dangerous work areas, has been mounted on a continuous mining machine and was mounted inside 1.3-cm thick angle iron. This loop antenna was exposed to more than six months of active underground coal production, which included being covered by and scraped over with tons of rock, sprayed by a continuous stream of water, and immersed in thick mud. After six months the loop antenna showed signs of wear, but was still capable of performing its intended function. The HASARD system is now being applied to other industrial applications and is showing much promise, especially in harsh environments. This paper details the system, describes the tests that have been done, and mentions other areas where it can benefit the safety of industrial workers.

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By Frederico Valadares de Andrade Resende

O uso de aglomerantes na pelotização é uma ciência que está em constante desenvolvimento de novos produtos, visando elevar o desempenho em suas aplicações, além da busca da redução e não incorporação de ganga ácida no produto final. Para tanto, a pelotização em parceria com fornecedores destes insumos está trabalhando em pesquisa para agregar cada vez mais valor nas pelotas de minério de ferro. Atualmente já ocorreram avanços na utilização da bentonita sódica superativada, com o desenvolvimento e aplicação em escala industrial, onde foi constatada vantagens em seu desempenho frente a outros tipos de aglomerantes. Porém, durante um maior período da utilização da bentonita sódica superativa em escala industrial, foram percebidas algumas influências não desejáveis no processo produtivo, as quais estavam interferindo diretamente no desempenho das plantas de pelotização que estavam utilizando tal aditivo em seu processo. Diante do exposto acima, foram estudadas possibilidades para adequação do produto, onde foi sugerida a alteração da formulação química promovendo uma redução do potencial de aglomeração do aditivo, alterando assim algumas características que estavam impossibilitando a utilização em escala industrial. Este trabalho apresenta a viabilidade da aplicação industrial da bentonita sódica superativada, após a reformulação desenvolvida em parceria com o fornecedor do produto, baseada em análises estatísticas dos resultados.

Aug 1, 2018

By G. M. Hughes

"400 cubic foot Agitair Flotation Cells are in use at Sherritt Gordon's Fox and Ruttan Mine Cu-Zn concentrators. The 4 impeller model No. 120, used at the Fox Mine Operation, appears to offer superior agitation and aeration qualities compared to the single impeller model 120A, in use at Ruttan. The advantages of the model 120 are most significant with ores of high specific gravity and coarse grind.IntroductionSherritt is using 400 cubic foot Agitair flotation machines at both the Fox and Ruttan Mine Concentrators.At the 3000 tpd, Cu-Zn Fox concentrator, 18 model 120 machines have been in operation since May, 1969.The 10000 tpd, Cu-Zn operation at Ruttan utilizes 49 model 120A machines. The plant started operation in May, 1973.The 4-impeller model 120 flotation cell has been marketed by Galigher since the early 1960's but the single impeller model 120A is relatively new.Model 120 Agitair -Cell DataThe Model 120 (Dwg. 1) has floor dimensions of 101 x 10' and a lip height of 2~ to 4 feet to provide up to 400 cubic feet of volume. This machine is shown with a froth crowder and stabilizer plates which are optional.Each motor drives two agitators. 20 HP is recommended by Galigher but 25 HP is more realistic with massive sulphides. The SG of ?ox ore is about 3. 6.The Model 120 can handle up to 600 cubic feet of air per cell at 2 psig which requires 5-6 HP at the blowers. Air volume to each impeller is controlled by a valve from a main header.During the first 3 years of operation at Fox there were few mechanical problems with the 120's."

Jan 1, 1974

By Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Zengqing Sun, Yanfang Huang

"Because of small specific surface area and poor ballability, vanadium/titanium-bearing magnetite is difficult for production of oxidized pellet. A novel organic copolymer binder, modified humic acid (MHA), has been authorized recently in China. Effects of the novel MHA binder on the quality of V/Ti-bearing magnetite pellets are studied in this paper. Experimental results show the MHA binder can obviously improve the strength of green pellet. Because of better heat endurance, the MHA binder pellet has a higher strength than Peridur pellet under the same preheating conditions. Moreover, TFe grade of pellet with the MHA binder is much higher than that of the bentonite pellet. The strength of preheated pellet containing MHA binder of 0.25%~1.0% meets the requirements of oxidized pellet production by grate-kiln process. Comparatively, MHA is a promising orgainc binder for iron ore pellets. Its price is only one tenth of Peridur price and about 3 times of bentonite price.IntroductionThe iron-making practices show that the use of pellet is beneficial to blast furnace life, productivity and fuel savings. Therefore, many iron-making plants have expanded the production of oxidized pellets in order to meet the needs of modern large-scale blast furnaces [1]. Presently, bentonite is widely used to improve the quality of iron ore pellets. The negative effects of using bentonite include decreasing total iron (TFe) grade and degrading the metallurgical properties of the final products [2, 3]. Many studies, therefore, have been conducted on the application of organic binders to overcome the weakness of the inorganic bentonite. In comparison with inorganic binders, one of the biggest strengths of organic binders is low residual silica content [4]. However, those studies showed that the economics of foreign organic binder addition into pellets was not attractive. For example, the compression strength of preheated pellets and roasted pellets are both too low, resulting in powder generation and ring formation in the industrial rotary kiln [3, 4]."

Jan 1, 2011

By Carl Henrich

While the size of the blast-furnaces used for smelting leadand copper-ores has constantly increased, during late years, the manner of removing the slag from the furnace to the slag-dump has (until quite recently, at least) practically remained the same. The only appliance in practical use has been the two-wheeled slag-pot, holding about 300 to 400 pounds of slag, or as much as one man could manage to pull or push on a smooth, hard surface. When these slag-pots on wheels were first introduced, the daily capacity of a lead or copper blast-furnace hardly reached 30 tons of smelting-charge. With furnaces of this size, and even when the capacity had been doubled, this kind of slag-pot answered well enough. All the improvements made were in the construction of these pots and not in an increase of their size, which was limited by the weight which one man could handle. But the size of the furnace went on increasing. The daily consumption of one furnace rose gradually to 75 tons, 100 tons, and even more. The writer had occasion to construct some of these furnaces, which, in their day, were among the largest, if not the largest, of the water-jacketed kind then in existence. A water-jacketed furnace will always smelt more in the same time than a furnace with brick walls. Already, in those days, the slag-removal from these enlarged furnaces received due attention by the writer. The removal of 60 tons of slag in 24 hours, in pots holding only 300 pounds each, will require 400 pots to be filled in 24 hours; and when the amount.of slag increases to 90 tons, 600 pots will be required. That is to say, in the last case, 25 pots in each hour, or 1 pot each 24 minutes, will have to be put under the slagspout, filled, pulled away, and replaced with another. This will involve too much hurry for any degree of comfort, convenience

Jan 1, 1896

By Kazutoshi Haga, Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Kawata, Refilwe S. Magwaneng, Kohei Mitsuhashi, Altansukh Batnasan

"The recovery of copper and iron from carbonaceous sulfide ore is of economic and environmental interest despite its processing difficulty. Hydrometallurgical methods can be used to concentrate sulfide metals of these hard-to treat ores in a simple and eco-friendly manner. In this study, high pressure acid leaching process was comprehensively studied to dissolve metals from an ore with organic carbon and carbonaceous gangue material using autoclave equipment. The sample used for the experiment was reduced to an average particle size of 75 µm after undergoing flotation to reduce carbonaceous gangue minerals. A comparative study on two leaching reagents of sulfuric acid and iron sulfate and their dosage was used to observe dissolution of copper and iron. Other parameters of temperature (90-170 0C), solid-liquid ratio (1:10, 1:5, 1:3 and 1:1) were investigated through kinetic studies to access the influence of organic carbon and carbonaceous material on recovery of copper and iron. Materials balancing analysis was used to evaluate the efficiency of metal dissolution. The effects of parameters on leaching rate and concentration was demonstrated. Results obtained from the experiment indicated low concentrations of copper and iron in pregnant leached solutions, which was attributed to acid consumption by organic carbon and carbonaceous material in feed. However, the high efficiency rates of 92.4% and 86.3 % for copper and iron respectively in sulfuric acid can be concluded that leaching of concentrates of carbonaceous ore is possible provided system control on type of acid, pH and temperature. The purpose of this research is important in understanding mechanism involved in dissolution of copper and iron in concentrates of carbonaceous ore and marks an improvement in leaching of highly contaminated ores."

Jan 1, 2018

By George S. Rice

ARIAL maps of prospective mineral-bearing territory have become almost indispensable in all the branches of exploration, and have proved particularly useful in the great oil area of the Southwest. About nine years ago aerial photographic mapping in this area was begun. The early product was lacking in scale accuracy and other control features, which limited its effective use. Since then, the evolution of the technique of such mapping has been steady, with several mapping companies collaborating with five of the leading oil companies, and aerial maps have been prepared covering practically the entire area.Improvements in cameras, film, and developing equipment and practice have resulted in more uniform and clearer photographs, but the outstanding development has been the accuracy obtained with respect to scale and all other control features. Maps are no

Jan 1, 1936

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015