Search Documents

By Limao Zhang

This paper presents a novel model to assess the risk of adjacent buildings in tunnelling environments based on Extended Cloud Model (ECM). ECM is an organic integration of Extension Theory (ET) and Cloud Model (CM), where ET is appropriately employed to flexibly expand the variable range from [0, 1] to (-8, +8), and CM is used to overcome the randomness and fuzziness during the gradation of evaluation factors. The risk level of a specific adjacent building is assessed by the correlation with the cloud models. A confidence indicator ? is proposed to illustrate the rationality and reliability of evaluating results. Ten buildings adjacent to Wuhan Metro Line Two (WMLT) are randomly chosen among hundreds of adjacent buildings for a case study. Results have proved to be consistent with the actual situation. Compared with other traditional evaluation methods, ECM has been verified to be a more competitive solution with high calculation accuracy, wide adaptability, as well as simplified computer programming. There are no stringent requirements on the quantity of training data during the modelling process, and the original data can be directly entered into ECM without a normalization procedure, avoiding the potential information loss. ECM can be offered as a decision support tool for the risk assessment in urban tunnelling construction and worth popularizing in other similar complicated projects.

Aug 1, 2013

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

By John M. Hird

Texasgu1f's Lee Creek Mine in Eastern North Carolina is usin8 a combination Dredge-Dragline method for mining deep phosphate ore at a rate of 8.5 million tons per year. The matrix is thick, uniform in grade, and is processed into agricultural products. As in many other good mineral deposits, there are tough obstacles to overcome in recovering the ore. The deposit is in an area with a land surface of about ten feet above sea level, is close to tidewater, is overlain with 90 to 130 feet of unconsolidated overburden, and is underlain by an artesian aquifer with over 140 feet of natural hydrostatic head at the bottom of the bed, The upper 40 feet of overburden will not support stripping equipment and is unstable when cast as spoil. Barriers are emplaced to prevent flooding from hurricane tides. The ground water problems have been successfully controlled by pumping 60 million gallons per day from the aquifer. Only recently have the severe ground problems been overcome by this unusual Dredge-Dragline combination of mining equipment.

Jan 1, 1978

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed. The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters. A good correlation between flotation, adsorption and surface energy as a function of amine concentration and pH was observed. The sudden increase in wollastonite flotation and amine adsorption at and above 5x10-5 M initial amine concentration is thought to be due to two-dimensional precipitation of amine on surface in accordance with the recent 2D-3D precipitation model of amine adsorption on silicate minerals.

Jan 1, 2003

By N. L. Piret

In copper smelting minimization of solid waste generation is receiving increased attention with more stringent environmental legislation and lower disposal space availability. Copper smelting slags generally being valorizable, solid waste generation is attributed to the presence in the feed of unvalorizable impurities which do not report to the slag and to the unavoidable formation of contaminated dilute acid solutions which need neutralization. As to unvalorizable impurities, solid waste minimization is achieved by rejecting them in the highest possible concentration. Dilute acid is mainly due to the formation of SO3 in the smelter gases and to the discard of decopperized bleed-off electrolyte. Its generation is substantially lowered by preventing SO3 formation, by converting the dilute acid to a valorizable product, e.g., by thermal decomposition for H2S04 recovery or by precipitation as chemical gypsum, and by suitable treatment of the bleed-off electrolyte for impurity removal. Industrial processes are evaluated and alternatives are discussed.

Jan 1, 1994

The longwall system with caving is the most common mining system in Polish Collieries and the extraction is carried out simultaneously on several levels and in different seams. The extent and diversity of the methane hazard occurring is strictly connected to the specific geological and gas conditions as well as to the applied mining methods. Taking these factors into consideration the following methane drainage methods are applied as additional means of combatting the methane hazard in Polish gassy coal mines: 1. predrainage by means of boreholes drilled from the surface, 2. predrainage from stone drivages and devel- opment workings, 3. degasification of coal extraction workings, and 4. degasification of sealed-off areas/old goaves. Predrainage gave satisfactory results when holes were drilled from the surface or from underground workings, but only to depths to 300 m. It was necessary to adapt methane drain- age methods to the geological and mining con- ditions as gassiness increased with depth. The results of methane capture, both pre- drainage and post drainage were obtained by investigating several gassy mines.

Jan 1, 1982

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By M. F. Chambers

The U.S. Bureau of Mines conducted experiments on electrowinning of neodymium metal by using a molten-metal cathode at 650° C and an electrolyte of 50 mol pct NdCl3 (neodymium chloride) and 50 mol pct KCI (potassium chloride). The molten-metal cathodes were alloys of magnesium and zinc or magnesium and cadmium. Current efficiencies were 90 pct with a Mg-Zn cathode and 80 pct with a Mg-Cd cathode; The Mg-Cd cathode was easily separated from the electrolyte. In contrast, the Mg-Zn cathode tended to mix with the electrolyte, making separation difficult. The cathode metals were separated from the neodymium by distillation at 1,100° C under a vacuum of 10-3 torr. Neodymium metal of 99.9+ purity was recovered from the Mg-Cd alloy cathode after 30 min distillation time. The neodymium recovered from the Mg-Zn system contained almost 2 pct Zn after vacuum distillation. Continuous operation using the Mg-Cd alloy cathode was demonstrated.

Jan 1, 2010

By Douglas Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

OFFICERS AND COMMITTEES OF LOCAL SECTIONS AIME Committee on Local Section Affairs Roger Pierce, Chairman Carleton C Long Thomas C Frick AIME Committee on Student Chapter Affairs John P Nielson, Chairman John C Calhoun, Jr J R Van Pelt, Jr Council of Section Delegates A A Burr, Chairman (Hudson-Mohawk) Ralph A Watson, Vice-Chairman (North Pacific) L G Neely, Secretary (West Central Texas) INTERIM COMMITTEE M O Langham (East Texas), Fulton J Olivier (Delta), L W Smith (Niagara Frontier), G R Spindler (Central Appalachian) LOCAL SECTIONS (There are 78 Local Sections in the United States, 9 Foreign) ADIRONDACK Established June 18, 1952 Official year begins in April Meets fourth Saturday monthly, April through October Seven meetings annually Local Section Dues AIME Members $2, Nonmembers $3 Charles F Dievendorf, Chairman Severn P Brown, Vice-Chairman George E Erdman, Secretary-Treasurer Gouverneur Talc Co , Inc Gouverneur, N Y Malcolm V Lowry, '60, Section Delegate Committees Membership David J Crawford, Chairman Program Brower Dellinger, Chairman Student Affairs Eugene A Eastman, Chairman

Jan 1, 1959

By S. Bagchi

The LaNi5-xMnx-hydrides have potential applications in cryocooling devices for non-mechanical method to compress hydrogen gas. Thermal aging behavior of LaNi5-xMnx-hydrides of compositions x=0.4 and x=1.5 has been investigated. The hydriding properties of the La1.02Ni4.6Mno.4 alloy do not change significantly after thermal aging at 453K for 260 hours. X-ray diffraction analyses of this aged alloy do not reveal the presence of any new phases but the Bragg peaks become broader. Line profile analyses show anisotropic microstrains with an average <e2>1/2 value of -5x103. Thermal aging of the other hydride, LaNi3.5Mn1.5 hydride, at 623K for 280 hours, showed significant disproportionation; the hydrogen capacity reduced significantly from an H/M value of 0.75 in the activated condition to -0.15 after aging. X-ray diffraction analyses showed disproportionated lanthanum dihydride, metallic Ni, and Mn phases. The Bragg peaks were very broad indicative of microstrains or small crystalline domains.

Jan 1, 1997

By Jennifer Riefenberg

The U.S. Bureau of Mines has long recognized the hazards associated with rock burst activity in underground mines. Concern over lost lives and resources prompted this study to further characterize rock burst occurrence as related to microseismicity and mining. A period of over 1,079 days of mining with 101 bursts, where microseismicity rates and blasting were recorded, was used in this study. Statistical analyses investigated relationships between (1) rock burst occurrence versus blasting, (2) rock burst size versus damage, (3) rock burst occurrence versus average micro seismicity rates, and (4) rock burst occurrence versus local mine geometry. Statistical analyses showed that 91% of all rock bursts occur with blasting while only 3% of all rock bursts occur, apparently, independent of blasting. Additionally, the long-term average daily micro seismicity rates appear to dictate when blasting will trigger rock bursts. Time series analysis on the daily microseismicity resulted in model equations that may be used to forecast the daily microseismic activity.

Jan 1, 2010

By Jei Y. Choi, P. G. Shewmon

The surfrrce-diffusion coefficients (DJ for Aulg8 on (100) and (111) surfaces of copper have been determined between 1050" and 780°C using a new avuzlysis imd experimental procedure. The results are: D, has also been determined fm cua4 at 870°C, and the values found are 4.5 times larger than those measured by the grain boundary grooving technique for the same surface orientations. This difference is felt to result from the approximate nature of the mathematical solution used in the present work. Attempts to measure D, for silver on copper and silver surfaces indicated a means of matter transport different from surface diffision was dominant in moving tracer from the source out over the surface. Cnlculations and experiment both indicate that this is the flow of silver through the vapor phase which completely masks the much smaller flow due to surface diffusion. The previous self-difhsion studies of D, for silver and copper are discussed in terms of our own analysis and found to yield values of D, factors of lo5 or more greater than those found by the grain boundary grooving tech -nique. UNTIL about 5 years ago it was widely believed that the activation energy for surface diffusion, AH, , was less than that for grain boundary diffusion, AHb,, which in turn was less than that for diffusion through the lattice, AHz.&apos; This was concluded from various evidence that D,> Db>Dl, and one tracer study of D, for silver on silver from which AH, was inferred.2 In 1959 Mullins and Shewmon demonstrated that D, could be determined from the kinetics of the growth of grain-boundary grooves.3 Using this procedure, Gjostein measured D, on copper between 800" and 1050°C and found that the activation energy was roughly equal to AHl .4 Subsequent work on copper,5" silver,&apos;,&apos; and goldg between the melting temperature T, and 0.87 T, confirmed that AH, as determined using the grain boundary grooving or scratch-relaxation technique was equal to or greater than AHz. During the same period, Drew and Pye again determined AH, for silver on silver using a tracer techniquelo and a mathematical solution similar to that of Nicker son and arker.&apos; Though the values of D, Drew and Pye measured at any given temperature were about 200 times smaller than those reported by Nickerson and Parker, they again found a low activation energy of about 10 kcal, or about one fifth that found at the higher temperatures with the mass transport technique. A distinguishing characteristic of these two previous tracer studies is that they have worked at low temperatures (-1/2 T,) where they felt volume diffusion was negligible and then analyzed these data as if all tracer atoms leaving the source flowed out into and remained in a homogeneous high-diffusivity surface layer of undefined thickness. This is totally different from the model used in the mass-transport studies or the studies of grain boundary diffusion, which assume the high-diffusivity surface layer to be only a few angstroms thick. If this latter model is applied to the earlier tracer studies, it is shown that the tracer has really pe!etrated into the lattice a mean distance of 1000A. Thus the tracer distribution observed after an anneal is thought to be due to the combined effects of surface and volume diffusion. Independent of the relative validity of the two models, it seems evident to us that any comparison of the values of D, as determined in these two ways is meaningless and misleading, since the values of D, and AH, obtained in these two ways would be totally different for the same physical distributions of tracer. Once the fundamental difference in the approaches of the two techniques is established, we are faced with the question of which model better approximates physical reality. Here all the evidence seems to be on the side of the &apos;&apos;thin surface layer" analysis. In fact, the authors of Refs. 2 and 9 do not argue for the "thick-layer model" we have described; they simply invoke it through the equation they use to calculate D, . The primary evidence for the thin-film approach is: a) grain boundary grooves and scratches widen in proportion to tU4 and Mullins&apos; rigorous analysis shows that this is only valid for a surface layer which is quite thin relative to the width of the groove;11 b) all accepted or seriously discussed models of solid-vapor interfaces and high-angle grain boundaries assume that the disturbed region of the interface is at most a few a0 thick. With the above in mind, it was desirable to determine D, using a radioactive tracer and a "thin-

Jan 1, 1964

By Richard D. Hagni

Process mineralogy has not been given adequate attention in years past, because geologists have not been sufficiently interested in applying mineralogical techniques to industrial processes, and most process engineers are not adequately trained to use them. Although some individuals and institutions have made efforts to improve the situation, it is only in the last few years that the significance of applying the methods of mineralogy to a wide variety of industrial processes has been fully appreciated. Presently, the formation and organization of several groups devoted to applied mineralogy have created a more amenable climate for the development of process mineralogy. As a result, the presentation, discussion, and publication of the results and case histories of process mineralogy have become fairly common. Short courses affording hands-on experience with applied techniques are now available to the many geologists and process engineers engaged in industrial mineralogical processes. The future role of the process mineralogist is viewed as an expanded one, which will increase in value.

Jan 1, 1982

By P. Marier, T. R. lngraham

The kinetics of the sulfation of MnO,, MnzO3, and Mn3O4 in SO,, SO3, and O, mixtures was examined and the descending order of sulfation rates at temperatures near 400°C was found to be Mn,O3 > MnO, > Mn3O4. The respective activation energies for the thermal decomposition of MnO, and Mn,O, are 39 and 47 kcal. At 900°C, the thernzal decomposition of MnSO, to MnzO3 is slower than that to Mn3O4. The respective activation energies are 62 and 51 kcal, respectitely. MANGANESE is used to improve the hot workability of steel in the proportions of approximately 13.5 Ib of ferromanganese per ton of steel produced. This requirement accounts for about 95 pct of its large industrial market in North America. The remaining 5 pct is used in the battery and chemical industries. In most North American ores, the percentage of manganese and the manganese-to-iron ratio are not suitable for the direct production of ferromanganese. Hence, most of the North American requirements for manganese are satisfied by importing ore. Typically, many of the studies done on native low-grade manganese resources have been directed toward the production of ore substittes" and the recovery of manganese from open-hearth slags.3 Of the wide variety of processes which have been proposed, the most popular involve compounds in the Mn-S-O system. The thermodynamic properties of manganese and its compounds were reviewed by ah&apos; in 1960 and, more recently, lngrahams discussed the thermodynamics of some of the reactions involved in the Mn-S-O system at normal roasting temperatures. The conditions for producing manganese sulfide during the reduction roasting of manganese sulfate are discussed by Fuller and Edlund.9 A novel scheme was proposed recently by zimmerley7 for utilizing waste sulfur dioxide from stack gases to recover the manganese from ocean-mined manganese nodules. Very little of the work published on manganese compounds has been related to reaction rates. Singleton et 1.&apos; studied the rates of reaction on the MnO-C and Mn7C3-3MnO systems and observed linear and parabolic kinetics respectively in the systems. Tatievskaya et a1.&apos; studied the low-temperature reduction of Mn&, MnO,, and Mn& in HZ and CO, and reported activation energies in the range 1628 kcal. In this paper, the rates of some of the decomposition and formation reactions involving MnSO4, MnOz, MnzO3, and Mn3O4 will be examined after the conditions for the thermodynamic stability of the individual compounds have been designated. CONDITIONS FOR STABILITY OF MnSO4, MnOz, MnZO3, AND Mn3O4 The areas of stability for h&apos;hSO4, MnOz, MnzO3, and h3O4 were established from the data of Mah4 and Ingrahams and are shown in the predominance area diagram,10 logpq- logpsq, in Fig. 1. The diagram is drawn for two temperatures, 700°K, solid lines, and 1100°K, dotted lines. The sketch for the lower temperature includes the conditions likely to prevail in the Zimmerley patent7 when manganese nodules react with sulfur dioxide and that for the higher temperature indicates the conditions for recovering MnzO3 or Mn3O4 from MnSO4 during a roasting reaction. From the fact that the boundary between the areas of stability of MnOz and hSO4 at 700°K is parallel to the abscissa, it is evident that MnOz and SO2 should react together to produce MnSO4, irrespective of the oxygen pressure in the system. If the source of sulfur for sulfation were from waste flue gases, it is likely that the oxygen content of the gas stream would be more than sufficient to oxidize any MnsO4 to MnzO3, 107 atm of O2 required, or even to convert any Mnz03 to MnOz, 0.02 atm OZ required, prior to sulfation. At 1100°K, the diagram indicates that MnSO4 may be converted directly to either MnzO3 of Mn3O4, depending upon the prevailing partial pressure of oxygen. When the gas stream contains more than 1 pct Oz, logpq = -2, only MnzO3 would be recovered from an experiment done under equilibrium conditions. At oxygen partial pressures of less than 1 pct, one would expect to bring about a reversible exchange between MnSO4 and Mn3O4 by appropriate adjustment of the partial pressure of SOZ. These various reactions will be described in the subsequent kinetic experiments.

Jan 1, 1969

By P. B. Mee

The secondary re crystallization behavior of two vacuum-melted, nominally 3 pct Si-Fe alloys has been studied, one alloy being produced from pure electrolytic iron and semiconductor-grade silicon and the other from commercial-purity hot band. The vacuum-melted and vacuum-remelted alloys were found to develop {110}(hhl) and {lll)(hkl), respectively, on annealing in high vacuum and {100}(0kl) and {11l}(hkl), respectively on annealing in pure hydrogen of dew point, < — 60°C. H2S doping of the hydrogen or annealing in commercial argon was found to effect a reversal for the vacuum-remelted alloy from (111) to (100) secondary recrys-tallization, while prolonged vacuum annealing at 2 x 10-6 Tow resulted in a tertiary re crystallization from (111} to (110). The growth selection of the {lll}(hkl) component was found to be governed predominantly by the {111}/planar misorientation, the maximum deviation of the resulting secondaries being 5 deg. It is considered that the driving force for {111}(hkl) secondary recrystallization arises from the preferential lowering of ?111, possibly by phosphorus or nitrogen diffusion, just as oxygen and sulfur under certain conditions have been found to preferentially lower ?100. When heavily cold-rolled metals are annealed at high temperatures, primary recrystallization usually occurs rapidly and may be followed by considerable grain growth. However, in the presence of a fine dispersion of inclusions1"3 or with a strong matrix preferred orientation4&apos;&apos; the matrix may be stabilized and a secondary recrystallization may then be effected. Also, in vacuum-melted Si-Fe it has been shown possible to develop {100}(001) and {110}(001)6 surface energy driven secondary recrystallization textures. Further, it has been found that, on annealing very pure metals, grain growth normally ceases when a grain size approximately twice the strip thickness is acquired, due to the formation of V-shaped thermal grooves which result in an equilibrium being set up between surface and grain boundary stresses. If, however, a surface energy difference ??s, exists between adjacent grains (of the order of a few percent of the grain boundary energy ?b), then according to Mullins8 a secondary recrystallization may be effected, since the grains having lowest ?s would grow at the expense of their higher-energy neighbors. For clean bee metal surfaces ?110 should be lowest; however, for 3 pct Fe-Si (100) secondary structures have frequently been developed and have been attributed by Walter and Dunn9 to an alteration of the relative surface energies due to the preferential chemisorption of oxygen on (100) planes. Kohler,10 however, indicated that this reversal may be achieved by employing minute quantities of highly polar compounds in the annealing atmosphere, i.e., sulfur compounds, in par- ticular H2S being beneficial in (100) growth. This work has been verified by Kramer" using {100)/{110} bicrystals, while Mager12 demonstrated the importance of sulfur diffusion within the strip. Detert13 has intimated that carbon may be responsible for the preferential lowering of ?110 although no direct evidence has appeared yet to support this supposition. It must , be appreciated that the above-mentioned examples of surface energy driven secondary recrystallization were obtained with very pure vacuum-melted materials with oxygen contents (which is now known to be a critical factor") less than 35 ppm. During the course of a textural study on Si-Fe it has been found that under certain conditions (111) secondary recrystallization can be obtained by what is believed to be a surface energy growth selection mechanism. The purpose of the present paper is to briefly describe this result and to try and postulate the possible causes. EXPERIMENTAL Two vacuum-induction-melted, nominally 3 pct Si-Fe alloys were produced, one from pure electrolytic iron and semiconductor-grade silicon designated A and the other from commercial-purity hot band, designated B.

Jan 1, 1969

The Burragorang Valley lies approx. 95 km by road south west of Sydney and some 35 km west of Camden. It is over 80 km in length and varies in width from 3 km to over 16 km. Geologically, the history of the Burragorang Valley is of interest. It was referred to by early geographers and N.R.M.A. booklets as the largest sunken valley in Australia. This description is incorrect as it is a water worn valley formed by the dissection of an uplift in the south western portion of the large Sydney Sedimentary Basin. Ages2 ago there extended right across the Blue Mountains, a continuous tableland into which the Nattai, Wollondilly and Cox&apos;s Rivers have carved out the formation of the Burragorang. This dissection together with other valleys such as the Megalong, Jamieson and Grose, formed part of the eastward drainage pattern of the uplifting tableland into the Pacific ocean. The lapse of time since the streams in the Burragorang began their work of erosion can

Jan 1, 1976

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"PROJECT OVERVIEWThe Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million inhabitants. The project was constructed by a joint venture of four South American contractors (“the JV”), and consisted of the following key components:• Treatment Plant: A 16 hectare area was cleared for the construction of a treatment plant to purify 900,000 m3/day of raw water from the Paraná River and distribute it to the surrounding communities.• Bored Tunnel: Nearly 15 km of 3.6 m inner diameter tunnel, ranging from 18 to 22 m below grade, was bored with two EPB tunnel boring machines to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions: Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access & Ventilation Shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of: one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (Intake and Treatment Plant, respectively), and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installed afterwards. Access Shaft 3, the intermediate shaft located between the launch shaft and the treatment plant, experienced persistent leaks during initial excavation attempts."

Jan 1, 2016

By S. LeFevre

, The solution of the housing and sanitation problem in mining communities, keeping in view both economic and humanitarian aspects, demands the best thought of the management of such enterprises. Upon the solution depend the health and comfort of the employee and his family, and as a consequence his contentment and efficiency. The following description covcrs briefly the methods installed for Witherbee, Sherman & Co. The operation of the system has been for about two years under the direct supervision of T. A. Hammond, Land Agent, and I am indebted to him for a compilation of the results. Sanitation The sanitary service covers 238 tenements. The installation cost was about $22 per tenement, as follows: Privy, $15; privy box, $3; proportion of incinerator cost, $2; garbage can, $2. The operating cost is $1 per month for each tenement. In considering the installation of an ordinary village system of water supply and sewerage two difficulties were encountered: First, lack of a sufficient quantity of water; there is no stream large enough, as Mineville is situated very close to the divide between the Lake Champlain and Hudson River watersheds. A storage reservoir was tried, but the only location available, among glacial hills, would not hold water. Second, the expense of digging ditches for the distribution of water and sewer pipes is so great as to be prohibitive; Mineville is built chiefly in a valley covered in the bottom with drift, in this case a combination of boulders and hard pan. Digging in this material costs 80c. to $1 per cubic yard, and pipes must be placed 41/2 ft. down to be below frost. The houses are scattered along 4 miles of streets, the oldest having been built in the original forest 65 years ago. The newer houses have gone up a few at a time wherevcr a clear space could be found and the slopes were not too steep. This has advantages, as it separates the dwellings into

Jan 1, 1915

By George S. Rice

INTERESTING developments going on in European coal mines look to: (1) increasing mechanization; 12) concentration of mining; (3) improvement in safety appliances; and (4) studies in bettering roof supports and. incident to this, studies of the way a roof behaves under different conditions of support and methods of mining and back-filling. Mechanization and concentration off mining is being adapted to a considerable extent in Great Britain coincident with the development of conveyors. Belt conveyors, shaker-pan conveyors, and a combination of the two are used. For pitching seams not steep enough for the coal to run in station-chutes, the. shaker-pan conveyor is more popular. For large outputs from a contiguous face, the double-unit system of face layout-that is, the conveyors meeting at a common point-is favored.

Jan 1, 1934