Search Documents

By Todd Wanless, Daryl Poduska, Prakash Donde, Mahmood Khwaja

"The proposed Minne Lusa Stormwater Conveyance Sewer is part of the Phase 3 Major Combined Sewer Overflow projects to be scheduled as part of the City of Omaha’s Long Term Control Plan (LTCP). The system features a 6,100 foot long, 14-foot inside diameter tunnel to provide for conveyance of separated stormwater from previously completed and future LTCP sewer separation projects to the expanded Storz West and Pershing Detention Basins and subsequently, the Missouri River. The tunnel will operate as a pressurized system and convey flows of up to 2,500 ft3/s resulting from a 10-year, 24 hour storm event. This paper provides a synopsis of the project with a focus on the overall design aspects related to siting the tunnel alignment in an urban environment, the hydraulic analyses performed to choose a pressurized system rather than an open channel system, and expected geologic conditions. Tunnel alignment and profile and geological profile are presented, as well as an overview of the construction related impacts considered during design. PROJECT BACKGROUND The proposed Minne Lusa Stormwater (MLSW) Conveyance System will provide for conveyance of separated stormwater from previously completed, and future, LTCP sewer separation projects to the expanded Storz West and Pershing Detention Basins and subsequently, the Missouri River. The project location is representatively shown on Figure 1; the overall conveyance system is represented in Figure 2. The MLSW Conveyance System consists of three separate construction contracts under Contract Numbers: OPW-52004 – The Storz West Detention Basin to 31st & Paxton Tunnel; OPW-52454 – The Storz West/Pershing Detention Basin Grading and Improvements; and, OPW-52752 – The Pershing Detention Basin to ML Outfall Channel. This paper focuses on the project covered under Contract OPW-52004: design and construction of an approximately 6,110 feet 14-foot inside diameter (ID) tunnel, constructed using a Tunnel Boring Machine (TBM). The tunnel will receive flows from the Paxton Boulevard (PB) and the John Creighton Boulevard (JCB) Stormwater Conveyance Sewers and convey the flows to the Storz West Detention Basin, resulting in CSO volume and flow rate reductions to the Minne Lusa Outfall Channel and the North Interceptor."

Jan 1, 2016

By Earl Ingerson

BORE surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. METHOD AND APPARATUS In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel ,bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. st the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 5000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (1:16), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1947

Innovative mining technology came to Texas in the form of bucket wheel excavator/cross-pit spreader systems. Texas Utilities Mining Company put the first system to work at its Big Brown Mine in December 1985. The second such system was put into operation at the Monticello Mine in February 1991. The cross-pit spreader systems are mobile, electrically powered, excavation and conveyor systems, the principal components of which include bucket wheel excavators (BVE) and an across-the-pit conveyor (spreader). These crawler mounted machines operate as a unit; the BVE's excavate overburden, feed it via conveyors to the spreader which in turn conveys the material across the open pit and onto the developing spoil bank. The system at the Big Brown Mine is composed of 2 BVE's and an across-the-pit conveyor while the Monticello system is made up of 1 BVE and a spreader. The BVE's prestrip overburden preparing a dragline bench for the final removal of overburden. Numerous evaluations, including lignite production requirements, economics, overburden characteristics, rehandle reduction, spoil stability, and the compatibility with dragline operations, led to the selection of the cross-pit spreader system at the Big Brown Mine. The system has proven itself as a viable and economical means of prestripping. The system's success at the Big Brown Mine led to the development of a second such system at Monticello. The advent of the cross-pit spreader system is viewed by Texas Utilities Mining Company as a viable solution to recovering deeper lignite reserves in a safe and economical manner.

Jan 1, 1993

By William R. Beloff, Franklin M. Grynkewicz, Puza

Construction of the MBTA Red Line Extension through Somerville, MA, called for driving twin tube tunnels through a zone of approximately 83m (273 ft) with mixed face conditions. While the majority of the tunnels were driven through competent hard rock using drill and blast techniques, the mixed face zone was advanced using floating crown bars for primary support. The overburden consisted of medium clay, underlain by water bearing glacial till, over a sloping bedrock surface. Due to the unusual nature of the construction techniques, a program was undertaken by the Contractor to monitor ground movement and stresses in the temporary steel supports. This paper presents a description of the instrumentation employed, as well as the measured ground movements and support stresses. Additionally, the tunneling techniques are briefly presented and commented upon. PROJECT DESCRIPTION The Davis Square to Porter Square Tunnel Contract is part of the Massachusetts Bay Transportation Authorities (MBTA) Red Line Extension from Harvard Square in Cambridge to the Alewife Brook Parkway via Somerville. The 5.1km (17,000 ft) Red Line Extension consists of four major new stations, three of which will be interlinked via tunnel construction, and the remaining station will be the last link of an open cut portion, and a terminal point for this phase of the extension. This 866m (2,790 ft) portion began at Porter Square in Cambridge and rose at a 4% slope through Somerville, terminating at the new Davis Square Station. Twin tube tunnels were constructed through 763m (2,517 ft) of rock and 83m (273 ft) of mixed face conditions at the Davis Square end. Figure 1 presents a plan view of the entire contract.

Jan 1, 1981

By M. S. Azun

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function ?(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [1 N-hy*(h) = 2(N h) i21 {Xi-Xi+h}Z, h=0, 1, N-1] where N is the total number of samples, Xi is the sample value at the i - th location, X i+h is the sample value at the i +h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2,…., up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any ar¬bitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of onedimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. ? References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity. ?

Jan 1, 1986

By Steven J. Page, John A. Organiscak, Thomas Mal

Monitoring the miner respirable quartz dust exposure for compliance with U.S. federal regulations is mandatory to protect the health of coal miners. However, there is no technique available for the direct measurement of the respirable quartz dust concentration in the mining environment. The only means to estimate the respirable quartz dust concentration is to perform an analysis of the respirable dust sample collected, which contains both coal and quartz dust as well as other mineral constituents. For samples collected at coal mines, the U.S. Mine Safety and Health Administration (MSHA) utilizes the P7 method for respirable quartz analysis. The objectives of this work are to 1) evaluate the performance of the P7 method on field samples of low quartz mass loadings, 2) evaluate the magnitude of dust mass spatial variability within an enclosed cab environment, and 3) estimate the subsequent propagation of error in calculating the per. centage of quartz over a broad range of mass and quartz filter loadings at a surface coal mine. These objectives were achieved by obtaining surface coal mine dust samples over a 9-month time period in enclosed cabs of three drills and three bulldozers. By measuring weighing precision and using reasonable estimates for sampler variability, the dust mass spatial variability component was calculated by difference. The results show that 1) the P7 method can be precise and linear with quartz mass loadings as low as approximately 5 µmg of quartz, 2) the dust mass spatial variability, even within an enclosed cab environment, is the dominant factor of variability in propagation of error in estimating the quartz content of the obtained dust samples on a percentage basis, and 3) weighing precision is not a significant factor in error propagation. In addition to the enclosed cab samples, samples from eight surface coal mine drills were collected at various locations exterior to the drill cab. Significant data scatter at these outside locations strongly suggests that the ambient dust mass spatial variability has a significant effect on the propagation of error in estimating quartz content of the dust samples on a percentage basis.

By Jean-François Boucher, Ernest K. Yanful, Mei Lin Shelp, Lionel J. J. Catalan

Shallow water covers for preventing acid production in tailings are based on the principle of minimizing oxygen availability. Resuspension of material from the tailings bed may result in increased oxidation and metal releases since dissolved oxygen is at near saturation levels in the water cover. Resuspension can be caused by waves and currents strong enough to mobilize the surface of the tailings bed. Tailings resuspension was measured with sediment traps in the Upper Cell of the Heath Steele site near Mirarnichi, New Brunswick Canada. Although significant amounts of resuspended tailings were collected in all traps, analysis of resuspended solids and bed tailings suggests that for the observed wind conditions resuspension did not occur at locations where the water cover depth was greater or equal to 1.0 m. Currents were likely responsible for the transport of resuspended tailings from shallower areas to locations where the water cover was deeper than 1.0 m.

Jan 1, 2000

By Jerry M. Whiting, Neil J. Duncan

"Does Canada need a mining industry? Isn't it a chronically depressed collection of businesses that pollute the air and water and tear up the countryside? Wouldn't it be better if Canada's investors devoted their attention to high-technology endeavours, tourism, and other relatively pleasant tasks?Probably the answer to whether Canada needs a mining industry in the 21st century is to look at the real mining industry that is in operation today. The facts indicate that mining is a very important contributor to Canada. It has certainly encountered some challenging times during periods of recession, and it face s severe and continuing problems of cost and competition in world markets. However, uneconomic mines have been closed, others suspended, and productivity has risen dramatically with employment at 77 000, down from 101 000 in 1981. The country's metal and non-metal mines, metallurgical plants and semi-fabricated metals industries employed an estimated 378000 workers in 1986, and paid wages than any other sector of the Canadian economy. This effort resulted in the production of 60 different metals, non-metals and structural minerals valued at $13.5 billion.The trade aspects of the mining industry are of paramount importance. If there is a reason for this situation to change during the next century. it eludes the authors. Canada has the well-developed expertise to discover, evaluate, develop, operate and profit from existing and new businesses based in an enormous area endowed with a nearly unbelievable variety of mineral resources. Many countries throughout the world must rely on producers like Canada, if they are to maintain and/or improve their standard of living."

Jan 1, 1988

By Lilong Zhu, Shaoda Zhang, Qian Wang, Shengping He

The effects of ZrO2, Y2O3 and Sc2O3, which are transition metal oxides, on the melting temperature, viscosity at 1300 °C, and break temperature of three mold fluxes (two weak-reactive type and one non-reactive type) designed for the high manganese and high aluminum steels, and one another conventional CaO-SiO2 based mold flux is studied. The results indicate that the melting temperature and viscosity increases slightly, and the break temperature increases dramatically with the addition of ZrO2, Y2O3 and Sc2O3 content in the conventional CaO-SiO2 based mold flux system. While, the addition of ZrO2, Y2O3 and Sc2O3 in the weak-reactive or non-reactive mold flux systems has a negligible in fluence on the melting temperature, viscosity and break temperature, suggesting that these transition metal oxides are possible to regulate radiation heat transfer without changing the basic properties of mold fluxes.

Mar 1, 2018

By F. H. Bunge, W. H. Jr. Dailey

This paper covers an investigation of the magnetic roasting characteristics of several iron ores when treated in the form of small pebbles (1/8" to 1/2" in size), and in the form of balled fines. The roasting treatment was carried out with apparatus capable of very close control of time, temperature, face velocity, and per cent combustible in the reaction gas. The effect of rapid initial heating was not studied although it is believed that this has a major effect on the results when processing solid pebbles. The test equipment is a fixed bed type, with such a wide range of gas velocities, temperature, combustible content and etc., that the results obtained can be made to approximate those from various commercial roasting processes. The data presented in this report covers reaction rates, effect of processing variables on silica in the concentrate, flow resistance of beds, and to a limited extent, the effect of particle size. The work is far from complete and raises many more problems than it gives answers for. We believe, however, that much of the information will be useful to those engaged in investigation of magnetic roasting processes. We measured the time required for various degrees of completion of the reaction of hematite to magnetite, for finely pound material in balled form and for carefully sized crushed ore. Measurements were made for a variety of Minnesota and Labrador ores. This report covers an ore requiring fine ginding (-325 M) for liberation (Lower Kevin) and an ore requiring coarser grinding (-100 M) for liberation (Upper Olson). These ores represent approximately the range of characteristics for a group in the west end of the Mesabi Range. Our data shows that the reaction rate is very fast for the finely ground material and that tests are readily reproducible. The reaction rate of the larger size material, in the range of 1/8" to 1/2", is much slower and the results more erratic. We found that for the ores tested, the percentage of silica in the Davis tube magnetic concentrate was a function of iron recovery. Normally the concentrate had a low and relatively uniform percentage of silica up to a critical value of recovery. Above this critical recovery value the percentage of silica increased very rapidly. For example, for one particular ore roasted in the form of 3/8" diameter balls made from -28 mesh fines, the silica remained at about 7% to 8% until the recovery exceeded about 93%. Increasing the recovery beyond 93% resulted in over 25% silica with the additional recovery. The degree of conversion of hematite to magnetite (% completion of roast) required to obtain 93% recovery for balled material, varied inversely with the gas flow rate. Percentage silica in the concentrate resulting from roasting 3/16" and 1/2" solid material was relatively erratic. However, for varying degrees of iron recovery the lowest silica percentages corresponded to those obtainable when roasting fines. It is thought the probable reason for the erratic values was the variation in shattering or cracking of the pebbles during initial heating and roasting. There is some indication that very fast initial heating will greatly increase the permeability of the individual particles of ore to gas flow so that the reaction rate for coarse sizes will approach that obtainable with balled fine material.

Jan 1, 1961

By J. M. Eriksen, T. Rosenqvist, H. Elstad, S. Seim, A. Hildal

The titanium industry demands high titanium feedstock for their processes. As rutile resources are limited, ilmenite has become the most important titanium source. Ilmenite smelting is an important part of upgrading ilmenite to high titanium feedstock. In the year 2005, upgrading of ilmenite by smelting, producing a slag with 80-90% Ti02, accounted for approximately 40% of the feedstock to the Ti02 pigment industry. In ilmenite smelting molten iron is produced together with a slag, which in addition to titanium oxide contains iron oxide as well as various impurity oxides of manganese, magnesium, silicon, aluminium, etc. Titanium is present mainly as Ti02 but partly also as Ti203. It is known that the concentration of Ti203 increases with decreasing concentration of FeO, but this dependency is affected by the nature of the impurity oxides. Sigurdson and Moore1 showed that slags high in CaO and MgO had a lower concentration of Ti203 than slags high in Si02 for the same amount of FeO. Pistorius2 showed in 2002 that if the impurity oxides MnO and MgO are counted, on a molar basis, as FeO, and Cr203, V203 and part of the A1203*), as Ti203, industrial slags will have a composition close to that of the M305 phase, where M denotes the elements Ti, Fe, Mn, etc, and which has the pseudobrookite structure. However, for equilibrium with liquid metallic iron he computed, by means of a computer program FACT, that the slag equilibrium composition is represented by a curved line in the ternary phase diagram FeTi03-TiO2-Ti2O3, but with a significantly higher concentration of trivalent titanium than actually observed in the industrial slags, and he discussed various mechanisms by which the slag during solidification could change its composition to a lower Ti203 content, but the possibility that the computed compositions might be wrong was not mentioned. Trane113 found in her research on titaniferous silicate slags a lower Ti3+/ Ti4+ ratio than that which is computed by the FACT program. The purpose of the present investigation was to study the equilibrium composition of Fe-Ti-O slag in equilibrium with liquid metallic iron, as well as the effects of impurities such as Si02, CaO and MgO on the slag composition. Industrial slags from TINFOS Titan and Iron KS (TTI) will also be discussed and their compositions will be plotted in the ternary phase diagram. These are slags produced from Tellnes ilmenite, quite high in magnesium and iron. Experimental In the past, equilibrium studies of the Fe-Ti-O slag system were difficult when it came to producing the slag. It was difficult to find a suitable crucible for the meltings. The highly corrosive slag would attack all known refractories, and the metal would attack metallic crucibles such as those made of platinum and molybdenum. In the present investigations the slag-metal combination was prepared in a high-frequency induction furnace with a vertically segmented water-cooled copper crucible. The crucible is shown in Figures 1 a and 1b. It was designed by the Australian Nuclear Science and Technology Organisation (ANSTO) with power from a 75 kVA high-frequency generator (750 kHz) supplied by Farfield Electronics Pty, Ltd, Australia. This enabled the slag-metal combination to be melted with turbulent stirring and is expected to be isothermal. The entire temperature gradient

Jan 1, 2007

By Ava Segal, Doga Cagdas Demirkan, Abhidipta Mallik, Sebnem Duzgun, Andrew J. Petruska

Search and rescue operations in mining heavily rely on humans. In the context of emergency situations within underground tunnels, the potential to utilize sensory technology for navigation assistance holds the promise of saving human lives. Our research introduces a device configuration designed to enhance the performance of search and rescue teams. This setup integrates LIDAR and thermal cameras with the Microsoft Hololens, facilitated by the NUC computer and ROS Bridge. Performance assessment involves quantifying the extent to which a user is willing to venture into a light-deprived section of the mine prior to necessitating supplementary illumination. The preliminary outcomes highlight the significant potential of augmented reality assistance in offering indispensable aid to first responders, thereby greatly augmenting the efficiency of search and rescue missions conducted during critical circumstances.

Feb 1, 2024

By G. Mercher

El presente trabajo refiere cómo los concentrados de cobre pueden fundirse en un sistema de ciclón con un reactor de soplo por alto. Asimismo, se describe el proceso de la técnica de flotación durante las dos primeras décadas del siglo anterior, donde el concentrado de grano era muy fino, aunque existieron razones económicas que contradecían el uso de tal concentrado de flotación en el horno de tiro. En este sentido, se utilizó el horno reverbetorio, cuyo trabajo neutro se encuentra libre de toda reacción química metalúrgica. La eficacia de este equipo permitió la construcción de otro horno, al tiempo que satisfizo las necesidades grandes de otras plantas de flotación eficientes. Sin embargo, surge la necesidad de mejorar dicho proceso a mediados de este siglo, conduciendo a la aplicación de otro métodos como el Outukumpu, el cual satisface los requisitos de control ambiental or concentración de las sustancias gaseosas detríticas, asi como al uso de otros equipos.

Nov 20, 1978

By David White

THE submission of carefully prepared estimates of the oil reserves of the United States calls for no apology or explanation. In this country, petroleum is a rapidly wasting asset and an occasional appraisal of the amount remaining in the ground is a simple business procedure to safe-guard the general welfare and the prosperity of the republic. The rumored danger of failure, in the near future, of the foreign supply on which we depend in constantly increasing amounts makes the immediate review of our available reserves the more imperative. The Director of the U. S. Geological Survey, in March, 1921, requested the American Association of Petroleum Geologists to cooperate in the preparation of new estimates of the oil remaining in the ground. With the members of this cooperative committee, state geologists, regional geologists, consulting specialists, and geologists and engineers attached to many companies worked both independently and through sub-committees. The reports for districts, counties, fields, etc., after review by local or state committees, were discussed by the joint cooperative committee in conferences that, in some instances, were attended by the original compilers of estimates for the states or smaller areas. Finally the data were reviewed and the figures revised by the joint cooperative committee, so that the totals given in Table 1 represent the opinion of the committee, which was composed of F. W. DeWolf, W. E. Wrather, Roswell H. Johnson, Wallace A. Pratt, Alexander W. McCoy, Carl H. Beal, C. T. Lupton, G. C. Matson, K. C. Heald, W. T. Thom, Jr., A. E. Fath, Kirtley F. Mather, R. C. Moore, and David White, chairman.

Jan 6, 1922

By Sam Tour

WHAT is a die-casting and what is the die-casting industry? From the literal translation of the words "die" and "casting"' one concludes that a die-casting is a casting made in a die. The casting may be of any metal or alloy or, for that matter, may be of some nonmetallic material capable of being cast, such as plaster of paris or glass. The die may be of any material that will take successive casts so it need not necessarily be metallic in nature. The term "die-casting," therefore, is indeed broad, though in practical usage it has come to mean the casting of metals and their alloys in metallic molds or dies. Even this limitation of the term leaves -a broad field, for castings may be made in a number of different ways. For example, the molten metal may be allowed to run into the die by gravity it may be sucked into the cavity of the die, it may be forced to take the contour of the cavity in the die by centrifiugal force, or it may be forced into the cavity under hydrostatic pressure. In England, castings made by practically all of these

Jan 1, 1935

THE first session of the production engineering group on Wednesday, morning, with J. B. Umpleby as chairman, recorded the principal developments since the Fort Worth meeting. Added to this was a lively discussion of pressure maintenance. Recent advances in the air-gas lift have resulted from the need of applying the method to smaller wells at lower costs. In many places intermittent flow has given excellent results, and numerous mechanical de-vices for its automatic control have been, developed. Papers by C. V. Millikan on the Mid-Continent field and by A. H. Bell on California, fields formed the basis for discussion. The maintenance of initial sand pressures was ably discussed for two Texas fields by t. V. Foran in a paper that not only outlined the technic of operation and the results obtained but also contained noteworthy cost data in terms of increased ultimate production. Mr. Foran recommends the use of air in the first stages of pressure maintenance as a means of determining sand conditions and directions of flow, later turning to gas, if available, because of its greater solubility on oil. A round table discussion on petroleum engineering educational problems, with H. G. George as chairman, brought out much interesting discussion that is difficult to summarize. The other Wednesday morning session was a refinery engineering symposium with T. G. Del-bridge as chairman and the economical application of heat for the general topic. A paper on the modern pipe -still, by H. S. Bell, and another by C. W. Stratford on the modernization of the cylindrical still elicited a lively discussion.

Jan 3, 1928

By G. M. Willis, F. L. Hennessy

The oxygen pressure in equilibrium with silver and Ag2O-B2O3 melts has been measured between 800' and 900°C, to obtain the thermodynamic properties of the liquid. The compound Ag20. 4B20:1 appears to exist in the liquid, which shows marked heat content and entropy effects. A KNOWLEDGE of the thermodynamic properties of binary liquid silicates, borates, and phosphates would be of considerable assistance in the interpretation of the behavior of multi-component metallurgical slags. However, the literature contains comparatively few studies of the thermodynamics of binary slags. The system Ag20-B,O, attracted our attention as it was known to give a single liquid phase,',' in which high contents of silver could be obtained (up to 61 pct Ag according to Foex2). Further, it would be expected that the partial pressure of oxygen over melts in equilibrium with metallic silver could be used to determine the activity of Ag2O in the Ag,O-B,O, system. In many respects, it may be expected that the reaction of a basic oxide with boric oxide would be analogous to its reaction with silica. Liquid immiscibility frequently occurs in both borate and silicate systems. With B2O3 and SiO reaction with a basic oxide presumably involves a breakdown of the three-dimensional network of the acid oxide by reaction with oxygen atoms common to more than one silicon or boron atom. Ag2O-B2O3 was therefore investigated as a model of a slag system in the hope that its thermodynamic properties would assist in understanding those of other systems. Several methods for determining the activity of a component in a slag have been described in the literature. Chang and Derge" used high temperature electromotive force measurements to obtain the activity of SiO2 in CaO-SiO2 and Ca0-Al203-Si02 slags, but the cell reaction in their work is not clear. low has used rate of volatilization and vapor pressure measurements combined with phase diagrams to obtain activities in the systems KO-SiO,, Na,O-SiO, and Li,O-SiO," and PbO-SiO26 Taylor and Chipman7 extrapolated their results for the distribution of FeO between liquid iron and CaO (+Mg0)-FeO-SiOl slags to obtain the activity of FeO in the binary FeO-SiO2 system. In principle, one of the most direct methods for obtaining the activity of a metallic oxide in a phase is by comparison of the equilibrium oxygen pressure for the system metal-pure oxide with that of metal oxide-containing phase. Schenck and othersa have studied the stabilization of Ag2O on combination with other oxides (MO,) in the solid state by measurements of the oxygen pressure in systems of the type Ag-Ag,O-xM0,-MOy-0, (gas). Schuhmann and Ensio" have determined the activity of FeO in iron silicate slags in equilibrium with solid iron, using CO/CO2 mixtures to establish known partial pressure of oxygen. Although the method gives the activity of FeO without ambiguity, the slag is not a binary system, and interpretation of the results in terms of the hypothetical binary system FeO-SiO, is not possible. If a metal is solid at temperatures at which the properties of the slag containing its oxide are to be studied, this method has the considerable experimental advantage that the metal can be used as the container for the slag, and contamination by contact with refractories is avoided. In this work, crucibles for Ag2-B,O, melts were made from silver, and the liquid brought to equilibrium with definite pressures of oxygen gas. The oxygen pressure PO, thus fixes the activity of Ag20 in the liquid silver borate. For the reaction at a given temperature. is substantially constant, is directly proportional to the square root of the equilibrium oxygen pressure. Varying the oxygen pressure changed the silver oxide content of the liquid and it was possible to obtain the activity of Ag2O over a range of composition. Experimental Procedure In principle, the method consisted of bringing melts in silver crucibles or boats to equilibrium at a fixed temperature under a definite pressure of oxygen and analyzing the glass after solidification. Materials: B2O3 glass was prepared from A.R. quality boric acid by fusion in platinum. The silver

Jan 1, 1954

By I. Gaballah

The chalcopyrite ore's anodic and cathodic electrodissolution are studied using a Porous Pulsed Percolated Electrode (3PE) reactor. Stationary solid electrode experiments are also performed to explore the mechanism of electrochemical dissolution of chalcopyrite. Experiments with a low - grade natural ore have been carried out at 25 "C in solutions containing 1 M NaCl and 1 M HCl. Galvanostatic and potentiostatic conditions are employed. The influences of current and potential on selectivity of the chalcopyrite ore dissolution are assessed. Anodic oxidation of this ore leads to a preferential dissolution of iron bearing minerals, whereas cathodic reduction is more selective with respect to chalcopyrite. However, in both cases the electrochemical dissolution is incomplete and the current efficiency is low. Design of the actual reactor has to be modified to increase the bed conductivity and to allow continuous experimentations.

Jan 1, 1994

By Edoardo Misano, Magali Schivre, Martino Semeraro, Alain Bochon

"INTRODUCTIONThe Laboratoire Souterrain de Modane (LSM) is an underground research laboratory located in the Western Alps on the French – Italian border. It is located in the middle of the 13km long Fréjus highway tunnel that links Modane (France) to Bardonecchia (Italy) in correspondence of the highest overburden of 1800m. The LSM current activity is mainly based on the investigations about the dark matter and requires very sensitive instrumentation which shall be protected from cosmic rays. To comply with the new legislation about safety in tunnels, the highway tunnels owners agreed in 2007 the construction of a parallel safety tunnel, at an average distance of 50m from the existing tunnel and the laboratory owner CNRS (Centre National de recherche scientifique) also decided to extend the existing laboratory with the construction of a new 17000 m3 cavern allowing the installation of wider and more powerful instruments that could increase chances of success of research. Preliminary studies stated that, considering both geological and functional issues, the most appropriate location for the new laboratory shall be in between the two tunnels and parallel to the existing laboratory (see Figure 1).Hence, the CNRS asked Systra, already in charge of the works supervision of the safety tunnel, to realize the design of the new cavern. The laboratory extension includes the construction of a 40 m long cavern with 300 m² cross section and two smaller tunnels connecting the safety tunnel and the existing laboratory to the new cavern. The minimum distance between the front face of the new LSM and the highway tunnel is about 25 m.The French and the Italian authorities, responsible of the exploitation of the Fréjus highway tunnel, asked the CNRS to develop an accurate study indicating that the construction of the laboratory extension would not have any negative impact on the existing structures of the highway tunnel. The main results of the developed study by Systra are summarized hereafter. The construction works should begin prior to the end of the construction works of the Fréjus safety tunnel in 2018."

Jan 1, 2016

By J. Szarkowski

"INTRODUCTION The Butte district of Montana is well-known as one of the biggest historic producers of copper in the world. It is also a classic example of a porphyry Cu-Mo system that has been overprinted by zoned, polymetallic (Cu-Zn-Pb-Ag) lode mineralization. After copper, silver was the next most important metal mined from Butte, with over 700 million ounces of total Ag production between 1880 and the present day. Although many papers have been written on the mineralogy of the early porphyry Cu-Mo mineralization and the high-grade Cu-rich lodes in the center of the district, relatively little information exists on the mineralogy of silver in Butte. The purpose of this paper is to summarize past and present silver production trends for the district, and to combine previously published work with new research to examine the mineralogy of silver in the Butte mining district. BUTTE HISTORIC SILVER PRODUCTION According to a recent USGS compilation1, Butte is one of the most Ag-rich porphyry deposits in the world, both in terms of average Ag grade (8.6 g/ton) and total production + reserves (Fig. 1). It is also the 2nd biggest Ag-producing mining district in the U.S. (after the Couer d’Alene district, Idaho). Annual silver and copper production data for the Butte district, compiled from various sources2,3,4, are summarized in Figure 2. Peak production of Ag and Cu was in 1917. While Ag production gradually declined in the ensuing decades, Cu production remained strong until the years leading up to the closure of the Berkeley Pit in 1982. In 1984, mining of the nearby Continental Pit resumed under a different operator, and continues to the present day. The Continental mine produced an average of 35,000 metric tons Cu and 575,000 oz Ag per year between 1984 and 20044. These figures do not take into account a period of mine closure in 2001-2003 due to an unexpected hike in utility prices. The long-term decline in Ag/Cu ratio of ore mined in Butte (Figure 3) is due to several factors, including: 1) changes in metal prices; 2) a downwards decrease in Ag/Cu ratio of most of the lodes with depth below surface; and 3) a shift in mining methods from selective underground mining of high-grade veins to open-pit mining of the bulk rock."

Jan 1, 2016