Search Documents

THE paper on "Specific Efficiency of the Blast Furnace" by Richard Franchot, which was pub-lished in the September issue of MINING AND METALLURGY, was presented for discussion at the Pitts-burgh meeting. The session opened with a discussion among S. P. Kinney, Mr. Franchot, and J. N. Reese as to the methods and results in sampling for cyanides in the blast furnace. This is covered in detail in writ-ten discussion below. T. T. Read objected to the use of the term specific efficiency as likely to be confusing. The blast furnace has to perform the function of reducing Fe, 03 to Fe as well as that of fusing the metal and, since the reduc-tion of Fe, 0? involves a CO equilibrium, it seems mis-leading to calculate efficiency on the basis of burning the , all carbon to CO? since it is not possible. Mr. Franchot replied that he used the term in the sense defined by Richards in his "Metallurgical Calculations;" but a subsequent search failed to reveal the term in Richards, who says (page 245, 1st edition): The practical conclusion is that a blast furnace generates in itself not much over 40 per cent of the calorific power of the fuel used, and rejects nearly 60 per cent; by using part of the waste gases to heat the blast, however, some of this rejected heat, to an amount representing net 5 to 10 per cent of the calorific power of the fuel used, is returned to and injected bodily into the furnace, thus rendering available for the purpose of running the furnace about 50 per cent of the calorific power of the fuel as a maximum. The efficiency with which the furnace applies this 50 per cent usefully to the objects of the reducing and smelting is another question for investigation.

Jan 2, 1927

By A. López-Valdivieso, M. A. Corona-Arroyo, M. Llamas-Bueno

Magnetite (Fe3O4) ore is concentrated by low-magnetic-field drums to recover a magnetite concentrate that is low in silica (SiO2). The presence of SiO2 in the magnetite concentrate for steel production increases the steel processing costs, so a major challenge in magnetic concentration is to lower the SiO2 grade in the Fe concentrate. This work presents studies that were carried out on the removal of SiO2 from the magnetite concentration at the plant scale. Studies were performed with a three 36 × 96″ drum unit processing 46 ton/h of rougher magnetite concentrate. These studies showed that silica appears in the magnetite concentrate by three mechanisms, namely SiO2 entrainment in Fe3O4 chains, heterocoagulation between Fe3O4 and SiO2 particles, and mineral locking of SiO2 to Fe3O4. The SiO2 entrainment mechanism had the highest contribution (75%) to the SiO2 recovered in the Fe concentrate. Electrokinetic studies on Fe3O4 and SiO2 showed that heterocoagulation occurs because of the low negative zeta potential of the minerals at the pH of the plant slurry. This study also showed that a high percentage of ultrafine size SiO2 particles trapped in Fe3O4 agglomerates was not removed by the dilution water for the slurry fed to the drum. To lower the SiO2 recovery in the drum magnetic concentration process, work should be directed towards the removal of trapped SiO2 in Fe3O4 agglomerates.

By Claudio José Martins da Silva

A planta siderúrgica da TKCSA possui em seu sistema de distribuição de gás dois flares (bleeders) que possuem funções distintas durante o regime normal de operação. O flare 2 é responsável por queimar o gás de alto forno de baixo poder calorífico, gerado no início do processo de partida do alto-forno até que o gás atinja as características adequadas para o aproveitamento e ser direcionado para o gasômetro. Já o flare 1 trabalha em conjunto com o gasômetro no processo de controle de pressão e vazão excedente de gás, quando da redução intempestiva de consumo de gás de alto forno. O presente trabalho apresenta a solução implantada pela TKCSA para garantir, sob quaisquer condições de fornecimento de energia elétrica, a operação dos equipamentos elétricos e de todo o sistema de automação e controle operacional dos flares. Podemos dizer que a operação do flares torna-se autônoma e relação ao sistema elétrico e sistema de automação e controle da distribuição de gás de alto forno. O sistema implantado promoveu uma elevação na segurança operacional dos flares, já que, a autonomia operacional impede o apagamento da chama eliminado a possibilidade de lançamento de gás cru na atmosfera.

Jul 31, 2018

By Amélia de Santana Cartaxo

A pedra cariri, devido a sua extração, produz um alto teor de formação de sobras, o qual polui muito os arredores dos municípios, prejudicando rios e relevos da região. O presente trabalho tem como objetivo caracterizar o resíduo da pedra cariri, juntamente com uma argila para propor seu uso na formulação de blocos de vedação. Inicialmente a pedra cariri e a argila foram beneficiadas. Estes materiais foram submetidos a um ensaio de plasticidade pelo método pfefferkorn, e posteriormente á analises de difração de raios-x e de fluorescência de raios-x, para saber suas composições mineralógicas. Através da fluorescência e da difração de raios-x comprovou-se que a pedra cariri possui um teor elevado de CaO(89,0%), que ajudará na densificação da peça e no abaixamento da temperatura de queima, e que a argila tem um percentual bom de sílica livre, que ajudará na eliminação do gás CO2 decorrente da decomposição térmica do carbonato presente na pedra cariri, ajudando também na estabilidade dimensional da peça. Pelas analises feitas, percebe-se um potencial de uso da pedra cariri na formulação de massas para fabricação de blocos de vedação.

Aug 16, 2017

By Ricardo Tadeu Meneses Sodré

Principalmente após a crise mundial de 2008, as grandes empresas brasileiras focaram na redução de custo como fator de sobrevivência, buscando manter, em contrapartida a produtividade e qualidade dos produtos. As normas brasileiras ABNT NBR ISO 55000/1/2, combinam atividades sistemáticas, coordenadas e práticas pelas quais uma organização gerencia de forma organizada e sustentável seus ativos tangíveis e intangíveis e sistemas, seu desempenho, bem como seus riscos e custos associados. A norma trata do ciclo completo do ativo, desde a concepção até o seu descarte. A implantação de uma norma deste porte requer compromisso de toda organização, principalmente da alta direção, no intuito de correlacionar os objetivos do negócio com as atividades de manutenção. O ponto principal é entender que a Manutenção é parte de um ciclo mais amplo que trata de todo o ciclo de vida do ativo, logo a Manutenção está contida dentro da Gestão de Ativos. O trabalho visa mostrar de maneira prática como a ArcelorMittal Tubarão está se estruturando para uma implantação futura da ABNT NBR ISO 5500X. Tal estruturação engloba atividades estratégicas, táticas e operacionais de alto nível visando à elevação da maturidade em Gestão de Ativos.

Aug 7, 2018

By Sarah Banks

"Here and there the grease and filth have caked solid, and the creek looks like a bed of lava; chickens walk about on it...and many times an unwary stranger has started to stroll across, and vanished temporarily." Upton Sinclair offers this revolting - yet accurate - description of the Chicago River in his book The Jungle, originally published in 1906. In the early 1900s, Chicago was a major industrial hub. The Chicago River was not only heavily used for transportation but also for the disposal of waste produced by the meatpacking industry, steel production, rail manufacturing and more. The South Fork of the river was the primary sewer for the Union Stock Yards. The meatpacking industry caused so much pollution, the river became known as Bubbly Creek. Chicago's older buildings were designed to be shut off from the river - no windows, certainly no homes or parks. A river view from an office or hotel was not something to brag about. It wasn't until the 1970s and the passage of the federal Clean Water Act that things began to change. The city now requires public access to the river in all parts and newer architectural designs ensure this is possible. Rather than sewage and industrial waste, the river now carries boat- loads of tourists and kayakers.

Oct 1, 2025

By R. M. Asimow

The magnetization curves for specimezs containing superparmagnetic particles are considered. It is shown that the curves may differ from a Langezlin function because of particle anisotropy, particle interactions , and the presence of a size distribution of particles. The various causes of particle anisotropy are considered, and magnetization curves for specimens with cubic and uniaxial anisotropy are presented. The magnetization curves depend on the In the particle-size below 100A it is quite difficult to obtain quantitative size and shape information on precipitate particles. All of the available techniques have their limitations; however, quantitative applications of superparmagnetism have not been developed as fully as possible due to a lack of analysis of the complete magnetization curve. With such an analysis it appears possible to obtain from a single magnetization curve of a specimen containing randomly oriented SPM (superparamagnetic) particles a quantitative volume distribution and a description of the particle shape.* sign of the anisotropy energy and in the case of a negative uniaxial anisotropy (prolate spheroids) the resulting curves may differ very considerbly from a Langevin function. A graphical technique is developed whereby it is possible to separate out the effects of the size distribution, the particle interaction, and the particle anisotropy. Thus it is possible to obtain quantitative values for both the particle shape and the size distribution. Langevin function2 I/Is = ctnh(HVIs/k T)-k T/HVIS [ 1 ] where I, is the saturation magnetization, V the particle volume, H the applied field, T the particle temperature, k the Boltzmann constant, and I the magnetization in the direction of the applied field. Such behavior is rarely if ever observed in actual systems. One explanation for this is that the SPM particles do possess a significant anisotropy and thus the magnetic energy associated with the particle depends on the direction of magnetization in a more complicated way than for the isotropic particle of Eq. [I]. In general the magnetic energy E of an isolated SPM particle embedded in a nonmagnetic matrix can be expressed as a sum of several contributions: E = Eh + Ed+Es+Ec [2] where Eh is the external field energy, Ed the energy resulting from the particle demagnetizing factor, E, the magnetostriction energy, and E, the crystalline anisotropy energy. In each term we consider only the part dependent on the orientation of the magnetization vector and the particle axes as the shape of the magnetization curve will be determined by these contributions. Following the same procedure used in deriving the Langevin function,

Jan 1, 1965

By J. D. A. Morrow

This discussion relates to the distribution of coal under the di , of the U. S. Fuel Administration beginning Apr. 1, 1918. At t' L a definite method of controlling and directing distribution was put int effect. Prior thereto, although some of the machinery utilized was in operation, especially in the few weeks immediately preceding' Apr. 1, distribution had not been effectively and comprehensively organized. The writer was called to the Fuel Administration by Dr. Garfield about the first of February, 1918, to assume general direction of the distribution of coal for the Fuel Administration, to develop the general plans, and to obtain practical men to assist in this work and in carrying through the program finally devised. A study of the situation and conferences with the Fuel Administrator and leading men in the business made it plain that it would be necessary to begin at the bottom, measure the undertaking, develop plans to meet the need thus shown, and build an organization to effect the distribution required. This work had to be done under war pressure in the midst of a bad coal shortage. The successful performance of such a task is always primarily a matter of putting competent men in the right places and giving them the power and opportunity to function properly together. In the Distribution Division of the U. S. Fuel Administration, the men who were chiefly responsible for whipping plans into practical form and then for carrying out these plans were A. W. Calloway, of Baltimore, President of the Davis Coal & Coke Co., who served as the Director of Bituminous Coal Distribution; S. Lovell Yerkes, of Birmingham, Alabama, Secretary of the Grider Coal Sales Agency, who assumed general charge of distribution while the new plans and organization were being perfected and then became the Assistant Director of Bituminous Coal Distribution; Warren S. Blauvelt, of Detroit, who was Director of Coke Distri. bution; A. S. Learoyd of New York, Director of Anthracite Distribution, in connection with the Anthracite Committee, consisting of Joseph P. Dickson, President of Dickson & Eddy, Chairman; S. D. Warriner, President of the Lehigh Coal & Navigation Co., and W. H. Richards,

Jan 1, 1920

By Wan Entong, Xie Junlin, Jiann YangHwang, Yang Chengwei, Chen Junfu, Zhang Jianjun, Cao Tongyou, He Feng, Peng Zhugang, Fang De

During the solidification process of peritectic steel (PS), the peritectic reaction often causes volume contraction which associated with surface longitudinal cracks, and using mould flux with low heat flux density help for alleviating surface longitudinal cracks. New peritectic steel mold flux with Co2O3 doping reduced the heat flux density, and the optimal content was found to be 2.0 wt %. Furthermore, basicity and Na2O addition were designed, and the minimum heat flux density required basicity of 1.4 and 10.0 wt %. Na2O content. As a result, the optimal peritectic composition was CaO(35.67wt% ), SiO2(25.48 wt %)，Al2O3(3.7 wt %)， MgO(2.53 wt %)，Na2O(10 wt %)，CaF2(14 wt %)，Co2O3(2 wt %).

Jan 1, 2015

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By N. Gopalakrishnana, R. Beccard, S. Lourdudoss, R. Holz, M. Deschler

"Rapid growth of conducting and/or insulating InP, GaAs, Gao.47In0.53As, and GaAs0.6Po.4 on one or more of (001), (110), (111)A, (3ll)A and (3ll)B surfaces by Hydride Vapour Phase Epitaxy (HYPE) is demonstrated. The maximum growth rate of the binaries lies between 12 and 300 µm/hr and of the ternaries between 7 and 170 µm/hr. A simple model is developed to describe the influence of crystallographic orientation on temperature dependent growth rates. The growth rates predicted by the model is compared with the experimental values. Room temperature resistivity of insulating InP:Fe can be as high as 5xl09 ohm cm. Temperature dependent differential resistivity is also analysed. This feasibility of growing conducting and insulating layers rapidly on different orientations is very useful for electronic and optoelectronic devices.IntroductionRecently there is a renewed demand for very thick layers of III-V compound semiconductors for high performance electronic and optoelectronic devices [1]-[2]. Long wavelength high speed lasers that can be modulated up to 30 GHz necessitate epitaxial growth of semi-insulating (SI) layers [3]. There is also an increased interest on the growth of epitaxial layers on surfaces other than (001) surface. Epitaxial growth of these materials on such surfaces is of theoretical importance besides being technologically relevant. These demands led us to focus on the growth of conducting and insulating III-V compounds by Hydride Vapour Phase Epitaxy (HYPE). lnP, GaAs, Gao.471no.s3As on lnP and GaAso.6Po.4 on GaAs were grown as conducting materials using Low Pressure HYPE (LP-HYPE) on (001) 2° off substrates. Gao511no.49P on (001) GaAs substrate and lnP on lnP substrates of (001), (110), (l 11)A, (31l)A and (3 ll)B orientations were grown as semi-insulating materials using Atmospheric Pressure HYPE (AP-HYPE). In this report we present the growth aspects of these materials. We also present a simple model on the growth of InP on substrates of various orientations. The theoretically obtained temperature dependent growth rates are compared with the experimental values. Differential resistivities of semi-insulating lnP grown on substrates of various orientations as a function of temperature are also summarised."

Jan 1, 1998

By D. Yu, T. A. Utigard, M. Barati

"Sulfation roasting of nickel concentrate to generate water-soluble metal sulfates was investigated as an alternative process to smelting for the recovery of valuable metals. The kinetics of dissolution of various species of the calcine in three leachants was studied; hot water, dilute HCl, and concentrated HCl. The results indicated that dissolution of sulfates by hot water at 90 ºC is achieved within 30 minutes. In order to increase the recovery of the valuable metals, acid leaching is necessary due to the existence of ferrite in the calcine.INTRODUCTIONInvestigations on the sulfation roasting of nickeliferous sulfide ores or concentrates were mainly carried out in 1950’s to 1990’s to generate water soluble non-ferrous metal sulfates followed by metal recovery by leaching (Stephens, 1953; Thornhill, 1954, 1961; Fletcher and Shelef, 1964a, 1964b; Fletcher and Hester, 1964; Frankiewicz, 1977; Norrgran, 1983). Commercialization of the sulfation roasting process was only performed by Falconbridge Ltd. (Thornhill, 1961; Boldt, 1967), which employed a sulfation roast process on nickeliferous pyrrhotite at 680 oC where Ni, Cu, and Co were leached and Fe2O3 was produced for the iron industry. In 1965, 118,342 tons of pyrrhotite was processed, however because of the huge SO2 emissions (no acid plant) relative to the nickel production and the poor economics, this plant was shut down.Nickel production from sulfide ores via pyrometallurgical means, especially the electric furnace smelting process, is a major emitter of SO2 to the environment and a big energy consumer (Warner, Diaz, Dalvi, Mackey, Tarasov and Jones, 2007). Nowadays, due to the more stringent environmental regulations as well as the need to reduce energy consumption, metal production by sulfation roasting is gaining more attention as an alternative process to smelting. The main focus of this paper is to investigate the extent and rate of leaching of valuable metals from the sulfation roasted nickel calcine, aiming to maximize the metal recovery and minimize the dissolution of iron species."

Jan 1, 2012

By Albert Sauveur

Some writers believe that when austenite transforms completely into pearlite on slow cooling through the thermal critical range, such transformation does not imply the formation of any of the so-called transition constituents: martensite, troostite and sorbite. Might it not be claimed with as much justification that when water freezes it does so suddenly, solid ice being obtained without passing through the intermediate stages of ice and water? Obviously, regardless of the speed of solidification, this would be erroneous. Before reaching the completed solid condition, this must of necessity pass through an unbroken series of stages when the system consists of mixtures of water and of ice, the former decreasing and the latter increasing in amount. Are not these "transitionV stages in the freezing of water similar to the transition stages occurring in the transformation of austenite into pearlite? To clarify, let us consider in Fig. 1 the mechanism of the transformation of eutectoid steel from its austenitic to its pearlitic condition as it cools slowly through its thermal critical range. It is generally admitted that this transformation is the result of two distinct phenomena: (1) the allotropic change of gamma iron into alpha iron and (2) the crystallizing out of solution of the carbide Fe3C. Whether this crystallizing of Fe3C implies also its formation is immaterial for our purpose. In other words, whether it is the carbon in atomic dispersion which is present in gamma iron or molecules of Fe3C has no bearing upon the matter to be discussed. The transformation of gamma iron into alpha iron cannot take place suddenly. It must of necessity be progressive, regardless of the speed with which it may take place. At A, for instance, there would be present AB gamma iron and BC alpha iron. The distance MN does not refer to falling temperature, but to the passage of time. It may be assumed that the transformation takes place at a constant temperature (the Ar321 point). In a similar way, the crystallization of Fe3C out of the austenite solid solution must be progressive as depicted between M and N. At A there would be present AB gamma iron, BC alpha iron, CD carbon dissolved in gamma and in alpha iron and DE Fe3C. This condition may be described according to individual preference as martensite or troostite. To sum up, can the metal pass from condition

Jan 1, 1931

By M. P. Adamson, Bryson D. Trexler, R. V. Ramani, Mark L. Koenig, V. Rajaram, Alan Burton, C. S. Crocker, Kim. Y. C., A. G. Law, William C. Larson

Another record year vas experienced by the mining industry as the value of nonfuel minerals production soared to $23.5 billion-up 15% from the previous year. Based on preliminary estimates by the Bureau of Mines, US mine output was the basis for about $225 billion worth of minerals-derived materials. Metal mining accounted for $8.5 billion, or 36%, of the total. Of the 22 metals produced in the US, 11 showed quantity increases, while 16 had value increases. Business Week's survey of 1200 companies (Mar. 17, 1980, pg. 81) revealed that 21 metals and mining companies had sales increases of 30% with earnings up 104%. Higher prices and increased demand for metals were primary factors behind the improved performance. The steel sector reported a 30% decrease in earnings for the year, but the slump was primarily the result of a $383-million loss for US Steel coupled with a 17% decrease in earnings at Inland Steel. Other firms did well in 1979, with earnings up 279% at Interlake and 269% at Kaiser Steel. Major obstacles facing the steel industry included substantial tonnages of dumped and subsidized imports, environmental expenditures, runaway inflation, and price controls. Turning to nonmetallic production, of the 49 commodities reported by the US Bureau of Mines, 29 had higher outputs and 39 had increased values. While production statistics may seem encouraging, government regulations continued to stifle industry efforts to develop needed new capacity. A case in point may be publication of the Environmental Protection Agency's simplified procedure to streamline five permit programs by consolidating them into one. The five included: hazardous waste management, national pollution discharge elimination, dredge and fill, underground injection control, and prevention of significant deterioration. The new procedure, published by EPA in the Federal Register, took 149 pages. AMC's J.A. Overton, Jr., noted that (MCJ, Nov. 1979, p. 39) to visually depict the complexity of the proposed regulations, Sell Oil Co. developed a flow chart mapping a path through one section. The chart required 10 days to map and two weeks for two draftsmen, using computerized drafting techniques, to plot the results. Overton said, "Perhaps the greatest service EPA has performed in preparing its proposal is to demonstrate again that federal regulations have become a complexity compounded by confu¬sion that culminates in a conundrum." While regulatory agencies promulgate new regulations, the lack of a cohesive government minerals policy remained a matter of significant importance to mine management. A non-fuel minerals study to provide input to the Administration for a national minerals policy program was a dismal shock, according to Rep. Jim D. Santini (D-NV). He said the first phase of the program, which was to identify industry problems, failed to come to grips with the hard decisions necessary regarding these problems, their impact, and their interrelationship. Santini said the report failed to acknowledge government's role in the process and absolved the government of any adverse influence on the domestic minerals industry. In response to the phase one report, eight senior mining executives testified before Santini's House Subcommittee on Mines and Mining concerning mineral supply, access to foreign sources, environmental protection, conservation and recycling, national security, and capital formation. By year's end, Rep. Santini promised to prepare a hard-hitting committee report on problems affecting the non-fuel minerals industry to provide a better base for subsequent policy recommendations (MCJ, Jan. 1980, p. 34). On the technological front, interest again centered on mechanization, automation, and scaleup to improve and expand production. Computer use increased for calculation of ore reserves, mine planning, operations research, and mineral processing.

Jan 5, 1980

MISCELLANEOUS U.S. 0,029,598 - Extraction of vanadium values from vanadiferous iron oxide ore. A pelletized mixture of ore, limestone and bentonite is roasted in an oxidizing atmosphere to form calcium vanadates, the calcine ground, the ground material leached with aqueous ammonium carbonate or sodium carbonate to produce a vanadium-rich solution while leaving an insoluble residue of calcium carbonate and/or calcium bicarbonate along with undissolved iron values, and the solution separated and treated for its vanadium content. This patent is a reissue of U.S. Patent No. 3,853,982, dated Dec. 10, 1974. C. B. Bare and J. W. Pasquali, assigned to Bethlehem Steel Corp. Mar. 28, 1978. 7 pp. (423-68). Filed: 3-3 1-77 (783,352).

Jan 1, 1979

By Wen Chen, Xinghua Liu, Zeyou Peng, Qiulin Wang

"Limonite is a collective for iron hydroxide argillaceous materials. It is very difficult to be treated due to the wide variation in specific gravity and magnetism and the high argillization rate in the course of grinding and beneficiation. The iron ore in Huangmei, Hubei, China is the typical representative of limonite. If the limonite is processed using conventional physical beneficiation methods (e.g. magnetic separation, gravity separation, flocculation-desliming-flotation, or a combined process of the three), it can only be obtained an iron concentrate grade of 51.98% and an iron metal recovery of 86.64%. However, the technique of flash magnetic roasting-magnetic separation can improve the concentrate grade to 61.03%, iron recovery to 91.17%. This paper describes the tests of recovering limonite by flash magnetic roasting in detail.IntroductionLimonite (mFe2O3, nH2O)[1] is a general designation for hydrous iron hydroxides and argillaceous matters. Limonite is hard to be separated because of its complicated geneses, comparatively weak magnetism, nonuniform grain size and being easily slimed during grinding. So most small and medium enterprises sell deslimed limonite product which was dealt with just by simple methods of washing, magnetic separation or gravity separation and so on. In recent years with the iron ore prices soaring, significant progress was made in mineral processing research of limonite. Laboratory research and industrial test results showed that flocculation-desliming-flotation process and roasting-magnetic separation process are the two best methods to recover limonite till now. To compare these two methods, roasting-magnetic separation process is superior to flocculation-desliming-flotation process in aspects of beneficiation indexes and industrial stability."

Jan 1, 2012

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The purpose of this section is to demonstrate the development of a method that we believe can be used for simulating and predicting mine water inflow. It will also show how important it is for personnel who model mine water inflow to have considerable experience with this subject, and with the conversion of hydrogeologic frameworks to conceptual models. Several of the models described previously are said to be three dimensional. However, closer examination reveals that there is considerable limitation in the variation possible in the third dimension. A true three-dimensional analysis would require a very large program. Therefore, it seems more reasonable to develop a procedure by which information from a two-dimensional model can be used for analysis of a three-dimensional problem. For a vertical mine shaft this is relatively easy because most two-dimensional models have an option for axisymmetric flow. If it can be assumed that axisymmetry exists about the centerline of the shaft it can be modeled easily as has been illustrated previously. For a horizontal drift or tunnel the analysis is not nearly as straightforward. However, the flow can be divided into two parts as indicated in Fig. 59. Part 1 considers the flow into the side of the drift while part 2 considers the flow into the end of the drift. To calculate the flow rate into the entire drift from the unsteady flow into a unit length the instantaneous flow per unit length may be integrated over the total length of the shaft. This procedure is shown in Fig. 60. The radial flow through any incremental length of the shaft is q. The total flow rate, Q, into the drift at any particular time is given by: The discharge q is a function of the time during which a particular segment has been draining that is dependent on the location x. In other words, a location at x = 0 has been draining during the entire time of expansion while a segment at x = L has only started to drain. Therefore, the time of draining at any point, x, is given by: [ ] where t' is the time over which the mine has been expanded. To determine the relationship between q and t it is necessary to refer to Polubarinova- Kochina (1962, pp. 566-569) and the equation given for the unsteady flow problem. This is: [ ] where q is the steady flow, q,, q, are the coefficients, and t is the time since drainage began. The expressions for q0, q1, and q2 are given as:

Jan 1, 1986

Shoveling ore cost so much at Tyrone during the year 1917 that it was deemed advisable to conduct tests to see where the fault lay. These tests were in the nature of time studies and extended over a period of very nearly a year. No data were available on this work to supply a starting point, so it was necessary to begin in a very elementary way, to find out the capacity of the average Mexican laborer. To' obtain a basis for comparison, it was necessary to determine the capacity of various types and sizes of shovels, so as to know whether the 21-1b. (9.5-kg.) load was the best load underground as well as on surface. A list of essential factors influencing shoveling was also made out during the course of a short series of preliminary time studies, and the motions involved in shoveling were analyzed and subdivided for convenience in studying. The necessary forms and record sheets were also decided upon at this time. A second short series of tests was then conducted on the surface, so as to be able to estimate the negative effects of underground work on the shovelers, and to minimize, as far as possible, the need for studying obviously poor types and sizes of shovels under the difficult conditions to be encountered in the mine. The test work underground consumed by far the greater proportion of the time and was divided into three series: Shoveling directly into a chute; shoveling into a wheelbarrow and tramming to a chute; and shoveling into a car and tramming to a chute. In each series the following points were determined for various lengths of time worked: Number of shovelfuls handled per minute, effect of distance thrown on shoveling speed, amount of rest required, amount of time consumed in tramming and dumping, proportion of working day occupied in shoveling, total tonnage handled during various working periods, effect of distance on tonnage handled during the day.

Jan 2, 1919

By Arcy R., D&apos George

Removal of S02 from smelter gases is being investigated, using an innovative technique that results in the almost simultaneous recovery and production of elemental sulfur. S02 is removed from the gas stream by scrubbing with suitable aqueous salt solutions or high-boiling organic fluids. The S02-laden liquor is then reacted with H2S Crystalline, high-purity sulfur is instantly precipitated and, after filtration, the regenerated liquor is recycled. The H2S required for the process is produced by reacting a portion of the recovered sulfur with hydrogen or with methane and steam. The chemistry and results of preliminary laboratory research are discussed.

Jan 1, 1969

By Albert Sauveur

SOME writers believe that when austenite transforms completely into pearlite on slow cooling through the thermal critical range, such transformation does not imply the formation of any of the so-called transition constituents: martensite, troostite and sorbite. Might it not be claimed with as much justification that when water freezes it does so suddenly, solid ice being obtained without passing through the intermediate stages of ice and water? Obviously, regardless of the speed of solidification, this would be erroneous. Before reaching the completed solid condition, this must of necessity pass through an unbroken series of stages when the system consists of mixtures of water and of ice, the former decreasing and the latter increasing in amount. Are not these "transition" stages in the freezing of water similar to the transition stages occurring in the transformation of austenite into pearlite? To clarify, let us consider in Fig. 1 the mechanism of the transformation of eutectoid steel from its austenitic to its pearlitic condition as it cools slowly through its thermal critical range. It is generally admitted that this transformation is the result of two distinct phenomena: (1) the allotropic change of gamma iron into alpha iron and (2) the crystallizing out of solution of the carbide Fe3C. Whether this crystallizing of Fe3C implies also its formation is immaterial for our purpose. In other words, whether it is the carbon in atomic dispersion which is present in gamma iron or molecules of Fe3C has no bearing upon the matter to be discussed. The transformation of gamma iron into alpha iron cannot take place suddenly. It must of necessity be progressive, regardless of the speed with which it may take place. At A, for instance, there would be present AB gamma iron and BC alpha iron. The distance MN does not refer to falling temperature, but to the passage of time. It may be assumed that the transformation takes place at a constant temperature (the Ar321 point). In a similar way, the crystallization of Fe3C out of the austenite solid solution must be progressive as depicted between M and N. At A there would be present AB gamma iron, BC alpha iron, CD carbon dissolved in gamma and in alpha iron and DE Fe3C. This condition may be described according to individual preference as martensite or troostite. To sum up, can the metal pass from condition

Jan 1, 1931