Search Documents

By S. Kahraman

The correlations between the modulus ratio and penetration rate of rotary and percussive drills were statistically investigated using the raw data obtained from the experimental works of different researchers. An inverse power law was found between the modulus ratio and the penetration rate of rotary and diamond drills. The penetration rate of rotary drills and diamond drills decrease with an increasing modulus ratio. The penetration rates of percussive drills increase with an increasing modulus ratio. There are significant linear correlations between the penetration rates of percussive drills and the modulus ratio. In one of the cases of percussive drilling, a strong correlation between the penetration rate and the modulus ratio was found for the rocks having a porosity value lower 1.23 %. It can be concluded that the modulus ratio might be a representative measure of rock drilling efficiency. However, further study is necessary to check the validity of the derived equations for other rock types. The effect of porosity on the correlations between the modulus ratio and penetration rate needs to be further investigated.

Jan 1, 2003

By W. S. Sanner

Pyrolysis (destructive distillation) techniques developed at the Bureau of Mines to determine the yield and quality of the products from coal were used to convert municipal (household) and industrial refuse into potentially useful solids, liquids, and gases without adding to environmental pollution. The tests demonstrated that a ton of municipal refuse can be converted into 154 to 424 pounds of solid residue, 0.5 to 6 gallons of tar, 1 to 4 gallons of light oil, 97 to 133 gallons of liquor, 16 to 32 pounds of ammonium sulfate, and 7,380 to 18,058 cubic feet of gas. A ton of industrial refuse, consisting of paper, rags, and cardboard, can be converted to 618 to 838 pounds of residue, 1.5 to 3 gallons of light oil, 68 to 75 gallons of liquor, 12 to 23 pounds of ammonium sulfate, and 9,270 to 14,065 cubic feet of gas. The energy from the gas is more than sufficient to provide the heat for the pyrolysis.

Jan 1, 1970

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By R. Addison

This is the story of the Carlton Mill. But first-a little geography. For those who do not know where the Carlton Mill is, or, perhaps, have only a vague idea, its location is indicated in Figure 1. The plant is situated on the road between the two old mining towns of Cripple Creek and Victor, 10 the west of Colorado Springs. From Denver, it's about 110 miles by road. The story of the Carlton Mill began with the discovery of gold at Cripple Creek in 1890. This discovery set off a major boom such that, by the turn of the century, there were 450 separate operating mines in the district. Gold production boomed early and declined rather rapidly as indicated by the graph in Figure 2. Significant factors affecting production are shown on the graph-the raising of the gold price in 1934 from $20.67 to $35.00 per ounce and the government executive order L-208 in 1942 requiring the closure of all gold mines.

Jan 1, 1983

By B. Caro Vargas

The Toulon Tunnel project is a key component of the highway corridor on the French Riviera between Marseille and Nice and is a fundamental transportation infrastructure for the region. The first design studies started in the 1960s. The tunnel project is comprised of two separate tunnels: south and north. The north tunnel was built between 1992 and 2002 after 10 years of difficult construction. On March 15, 1996, for example, a collapse of the tunnel in the Marchand area generated a sinkhole in the city center, causing a 20-month delay. The south tunnel alignment runs parallel to the north tunnel below Toulon?s historical downtown at a depth of 20 to 40 m (65 to 131 ft) with some areas with less than 10 m (32 ft) of cover. The risk management program was studied to be a state of the art program in urban tunneling construction.

Jan 1, 2012

By John Dodd

Advances in the technology of abrasion resistant irons and steels, which could help in combating abrasion and wear in mining operations, are reviewed. Nodular irons alloyed with nickel or copper and molybdenum, with acicular, bainitic or bainitic-martensicic microstructures are described. These alloy irons combine excellent castability and relatively easy machinabilitv with good resistance to wear. Recent progress in the development of high chromium molybdenum alloy irons is outlined, by which high temperature heat treatment of massive castings can be eliminated, alloy costs can be reduced and cracking problems avoided. Data is also given on the erosion-corrosion resistance of these irons. Trends in the development of improved cast steels are outlined. Factors influencing the toughness and abrasion resistance of manganese steels are considered. The 6% Mn 1% Mo manganese steels are shown to have a useful combination of toughness and abrasion resistance. Composite castings are seen as a means of com- bating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1981

Contents.SummaryIntroductionSituation, climate, topographyHistorySize of depositsPrevious investigationsGeological History of AreaMap compilationHistorical summaryNature and Significance of Granitic RocksSynchronous granitesMain subsequent granitesSignificance of types of bathylithsGeological StructureNorth-south anticlineCross-foldingFormation of channelwaysHydrothermal Depth-Zoning at CobarAssociation of Ores with PorphyryOrigin of replacement porphyriesTransgressive porphyriesSummary of ore-porphyry relationshipsSource of the Copper and GoldProspecting Targets, Cobar-NymageeGeneral ApplicationBroken HillThe Bendigo FieldKalgoorlie-Coolgardie, Western AustraliaConclusions

Jan 1, 1950

By Walter R. Storms, Jerry W. FAUST

This paper, which describes mining methods and costs at the Kearney zinc-lead mine, is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices, methods, and costs in varicus mining districts of the United States. The Kearney mine, which is owned by the New Mexico Consolidated Mining Co., a subsidiary of the Peru Mining Co. (Illinois Zinc), is situated a few miles southeast of the town of Hanover, in the northwest corner of sec. 27, T. 17 S., R. 12 W., in the Central Mining District, Grant County, N. Mex. (Figs. 1 and 2.) This report presents a brief history of the district, describes the geology, and outlines methods of prospecting and exploration, including eampling and estimation of tonnages and values. Development and mining methods are explained, and transportation, ventilation, drainage, safety measures, and organizatich are described. The wage scale and mining costs comprise the concluding sections of the report.

Jun 1, 1949

By Lawrence M. Gochioco

The interpretation of coal seismic data requires a certain precision and accuracy to make the results more reliable. The signature of the seismic wavelet provides a host of valuable geologic information. Subtle features and anomalies, not easily observed in conventional black and white seismic sections, are enhanced through color attribute displays in terms of frequency, amplitude and phase. Coal seam anomalies like sandstone washouts produce a distinct pattern in frequency and amplitude displays due to the change in the net acoustic impedance contrast. Faults produce frequency and amplitude variations due to interference within the Fresnel zone that straddles the fault. The magnitude of displacement is estimated by studying the effects of faults on reflection amplitudes and frequency from computer-generated models.

Jan 1, 1989

By Gordon B. French

The Occidental Oil Shale mining and retorting system for the production of shale oil has many advantages over the conventional underground mine and surface retort systems. For example only a portion of the oil shale is mined and transported to the outside, where it blends with the existing shale talus found on most of the slopes in the immediate area. The retorted spent shale is retained underground so that it does not become a surface disposal problem. The process consumes only minor amounts of water which is produced in adequate amounts in the retorting to fulfill all mining operations needs without outside supplies. Noise and dust levels are kept to a minimum with most of the facilities located underground. The exception being the generating stations and facilities as required to monitor air and water qualities, and last but not least, more than four times as much oil is pro¬duced from a given acre than from conventional surface processing. With the increased thicknesses as available on the government monopoly area this number could be increased by a substantial amount.

Jan 1, 1975

By Lok M. Sharma, Deep K. Khatri, Bradfield. Brett

"A shored enclosure was required to access a control structure upstream below the dam of a deep lake. The shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures. However, traditional analysis does not take into account soil-structure interaction. Numerical modelling offers better means to analyze soil-structure interaction. This paper presents a 2D finite element (2D-FE) analysis of a deep excavation support structure that was required to remove and replace a control structure at the upstream toe of a dam. The sheet-piling shoring was designed to withstand the lateral pressures from 14 m deep free water and 5.5 m deep excavation below the free water to reach the required excavation level to replace the gate structure. Elastic-plastic analyses were performed to predict the stresses and deformations of the complicated shoring structure and excavation bottom. The soil parameters, procedures used to develop the 2D-FE model, and the results are discussed in this paper. The shoring system is currently under construction.INTRODUCTIONA deep shoring system enclosure is required to keep out water and soil and to provide a support for unbalanced loadings due to dewatering and/or, excavation in order to permit construction of the permanent structures in the dry. A braced shoring system consists of a single wall sheet piling which is driven into the ground to form a “box” around the excavation site and is braced on the inside. After bracing the sheet piling, seal concrete is placed into the bottom to prevent water from seeping into the open excavation from underneath the sheet piling, and the water is pumped out to provide the dry work area. The braced shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures, (active, passive, or apparent pressures). There have been some uncertainties regarding the actual distribution of earth pressures due to influence of the support wall flexibility, as these traditional methods do not take into account soil-structure interaction. Numerical modelling offers better means to analyze soilstructure interaction."

Jan 1, 2017

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

By Fábio Rogério do Carmo

O ar soprado é uma das principais utilidades responsáveis pelo processo de transformação do minério de ferro em gusa no Auto Forno. Para que ocorra o processo de redução o ar soprado é superaquecido nos regeneradores dos autos fornos a uma temperatura de 1.300°C. Este energético é fornecido na CSN-UPV pelos turbos sopradores da Central Termoelétrica nº 2 (CTE#2), área dos Motos Sopradores 1 e 2 e os turbos sopradores n°1 e 3 da CTE#1 que operam com a velocidade reduzida 24 horas soprando para atmosfera e consumindo vapor de 30Bar. Devido à obsolescência do sistema de ar soprado da CTE#1, alto custo de operação e risco para a segurança operacional, este trabalho apresenta o estudo do problema em questão, a metodologia utilizada para desativação do ar soprado da CTE-1 e a redução de custo.

Sep 25, 2017

By E. O. Binyone

"https://www.youtube.com/watch?v=PBPyGXjlBHIhttps://www.youtube.com/watch?v=3AbtiKOYg7Y&feature=push-fr&attr_tag=uKtVW3yq2ZngptnE%3A6https://www.youtube.com/watch?v=PR2THayf-N8https://www.youtube.com/watch?v=mF-BXiWocqIhttps://www.youtube.com/watch?v=TuesIw-OZA4https://www.youtube.com/watch?v=v2HP7sTIZgEhttps://www.youtube.com/watch?v=v2HP7sTIZgEINTRODUCTIONIn 1937 the Eureka Corporation, Ltd., of Canada obtained a lease on the mining property of the Richmond-Euroka Mining Co. in the Eureka mining district, Eureka County, Nevada. In 1910 the Richmond-Eureka Co. suspended all operations except small-scale leasing, but company and other geologists contended that the El Dorado dolomite would also carry ore in its continuation from fault block north and northeast of the productive old working. The company began to explore the fault block in 1923 by diamond drilling from the,900 level of the Locan shaft, but for various reasons the hole was drilled to a depth of only 2 feet and was then abandoned. Eureka Corporation, Ltd., planned an extensive diamond-drilling program, which included four deep diamond-drill holes, one designated ""A"" fig. if it is to be drilled from the surfaced, and three designated ""E"", ""C"" and ""D"" figs land to be drilled from the 900 level of the Locan shaft. Of these only B and C were completed by the company. Hole C was a contribution,of the hole started by the, started by the Richmond Eureka Co. The site for hole D (figs. 1 and 2) was prepared, but the hole was not drilled. Both B and C holes penetrated sulfide ore carrying good percentages of zinc, lead, gold, and silver. The ore bodies were 40 feet thick and were found approximately 1,400 feet below the 900 level of Locan shaft.On the basis of the very favorable results obtained from the drilling program, the Eureka Corporation planned extensive development of the property and in 1942 commenced sinking the Fad shaft (figs. 1 and 2). The shortage of equipment and materials brought on by the war and difficulties with water in the shaft greatly hindered progress. However, early in 1943 the Eureka Cor¬poration, Ltd., of Canada submitted to the War Production Board a proposal for developing the mine and milling 500 tons of zinc-lead ore a day. The proposal involved an expenditure of $2,890,750."

Dec 1, 1946

By Michael Rieber

This study is an extension of our previous work in the area of coal transportation Its subject is the comparative costing of competing transport erodes. A wide range of costs and aspects of costs are dealt with in terms of engineering - economic analyses of the cost of the components which make up the facility and operating system descriptions of each coal transport mode. The cost comparisons, though analyzed, are not meant to be statements of policy but, rather, an input to decision making. The technical material presented in the succeeding volumes, alone with the earlier work cited above, forms the basis for the analyses. This material may also broaden the general understanding of coal transportation issues and problems. The project is divided into two main sections: (1) lone distance coal transport and (2) gathering and distribution systems. Within each section economic and technological comparisons are made of the available modes. These are used as the basis for comparisons among the modes. Inter-modal compatibility is studied with respect to both mixed trunk line shipment anti with respect to feeder to trunk line and trunk line to distribution systems. The engineering and technological data form the bases for the costing and economic analyses.

Jan 1, 1977

By W. S. Dyer

Introduction In northern Ontario, refractory clay is found on four rivers of the James Bay watershed: the Abitibi, the Mattagami, the Missinaibi, and the Moose. The clay all belongs to the same geological formation ( the Mattagami of Lower Cretaceous age) , and occurs within a structural depression or 'basin', the boundaries of which have never been defined but which appears to cover at least 1,500 square miles of territory. The recently constructed James Bay extension of the Temiskaming and Northern Ontario railway crosses the northeast end of the basin at the Onakawana lignite field, which by rail is 126 miles north of Cochrane, 605 miles north of Toronto, and 60 miles southwest of Moose Factory. Smoky Falls, the northern terminus of the railway owned by the Spruce Falls Power & Paper Company, Limited, is 7 miles south of one other point in the basin, i.e., the outcrops of refractory clay, sand, and kaolin at the foot of Long rapids on the Mattagami river. Smoky Falls is 50 miles north of Kapuskasing. In a very early report(l) , Dr. Robert Bell, of the Geological Survey of Canada, described '"light coloured marl in horizontal beds" from the Missinaibi river, and noted that the lignite also occurring in the river was probably :associated with the marls. This was undoubtedly the Cretaceous refractory day. Other early writers noted the occurrence of fire-clays, but it was not until Joseph Keele(2), of the Geological Survey, visited thee region in 1919 and studied the clays that their real significance was known.

Jan 1, 1933

By Jerry Pyatt

Lead has been used by mankind since before the Egyptian pyramids were built. Its durability provides for a continuum of innovation. As the largest integrated lead producer in the Western Hemisphere, The Doe Run Co. is committed to locating, mining, processing and sup-plying lead in ways that are responsible and sustainable. It takes ingenuity and resolve to successfully operate in the heavy industry field today. Doe Run is committed to applying responsibility through sustainability, lean manufacturing, safety, environmental stewardship, education and workforce development, and com-munity support.

Jan 1, 2008

Jan 1, 1970

By W. D. Haselton

This paper dealing with the mining methods used in producing iron ore from an underground operation located in the central-western part of the Mesabi Range in Minnesota is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The mine here discussed was laid out in accordance with a plan adapted to a rather unusual type of ore body, the nature of which is such that the mining method necessarily differs in certain respects from the method used at most of the mines in this district. A description of it may therefore be of interest.

Jan 1, 1930

The Mineral Sector Development Project, sponsored by the World Bank, has been set up to revise the legal, regulatory and fiscal framework for the minerals industry in Tanzania, with a view to attracting mining companies and investors to the country and facilitating future minerals development. One component of this project, the Environmental Management Framework for the Mineral Sector, was awarded to Wardell Armstrong of the UK and ENV Consult of Tanzania. In developing a new framework of environmental regulations, emphasis was placed on developing realistic standards which reflect local conditions and prevailing values. The main corner-stones of this approach are; effective environmental impact assessment procedures; establishment of environmental management procedures; and monitoring and auditing of companies? performance. The favoured approach involves a three-tier framework, as follows: ?Framework environmental provisions within the new Mining Act; ?Regulations covering more detailed environmental requirements ?Guidelines and/or Codes of Practice, which may in future become regulations in their own right. Careful consideration has been given, in developing the framework, to the limited resources likely to be available for implementation to the Ministry of Energy and Minerals and this has influenced the approach that has been adopted. This paper outlines the main components of the environmental management framework and discusses some of the important issues raised by these proposals.

Jan 1, 1998