Search Documents

By V. Damiano, M. Herman

CELLULAR substructure observed in metal crystals grown from the melt. has been studied extensively'-' and is attributed to the existence of a constitutionally supercooled zone in the liquid ahead of the solidifying interface. The mathematical description of this process has been given in terms of the concentration of solute in the liquid phase, the rate of solidification, and the temperature gradien.t in the liquid as the only variables.5 This technical note presents some evidence of 1) the effect of crystal orientation on some aspects of cellular growth, and 2:) the degeneracy of these cells into dislocation arrays. The zinc single crystals used in these studies were alloyed with cadmium sufficient to produce the constitutional supercooled cellular substructure. Crystals containing 0.05 pct Cd exhibited substructure formation for a growth rate of 10 cm per hr and a temperature gradient of 15°C per cm in accord with the theory. The growing liquid-solid interface was examined after we liquid had been decanted away in a fashion similar to that described by Rutter and Chamers.' The cellular substructure was also observed after polishing and etching the surface directly behind the decanted interface with a solution of HNO, and water. Fig. 1 is a photomicrograph of a typical polished and etched surface revealing substructure, the cleavage plane, and twins. The crystal has been grown with its basal plane parallel to the direction of growth and the plane of the micrograph is per-

Jan 1, 1960

By Richard E. Gray, William S. McCann, Robert C. Speck, Robert W. Bruhyn

Subsidence of the ground surface is the inevitable result of high recovery longwall and room and pillar coal mining operations. Up to now, U.S. research into this phenomenon has been concerned primarily with documenting the magnitude and extent of ground movements and prediction of the attendant ground strains through traditional ap¬proaches that have been developed in Europe and the United Kingdom. Preoccupation with ground strain prediction has, unfortunately, diverted attention from the more meaningful objective of predicting the severity of damage to structures at ground surface and the prob¬able cost to repair such damage. An attempt has been made to rectify this situation by reviewing in detail one hundred thirty four cases of subsidence damage to dwellings above active mines in western Pennsylvania, identifying the types of damage and the circumstances under which damage took place. The data reveal that damage to dwellings virtually always includes basements in addition to the readily apparent effects to the superstructure. In 90 percent of the subsidence cases, more than half the repair cost is associated with damage to subgrade components. A damage classi¬fication system has been devised that relates observed damage to severity and repair cost in a uniform manner for conditions in the Northern Appalachian Coal Field. Damage severity has been examined in the context of depth to the mine, the character of the near¬ surface overburden materials, mining type and other parameters.

Jan 1, 1983

By Stuart H. Ingram

The term lightweight aggregate implies material which may be substituted for the usual rock, sand and gravel commonly used as the major part of concrete, but distinguished by being much lighter in weight. Background The art of making and using concrete is old and well developed. Research and experience have pretty well determined the qualities necessary in its constituents, and time has tested theories and applications. Elaborate specifications and tests have been devised and generally adopted governing all phases of concrete work, from selection of material, through engineering design and down to mixing and placing. Standard practices have become routine to executives and laborers, and operations have been simplified and costs lowered. Though many lightweight aggregates meet the basic specifications necessary for usefulness, their physical qualities are so different that they fiequently will not pass standard tests, and some of them cannot be mixed and placed with the usual formulas for water and slump. As a rule their use produces a concrete with a lower modulus of elasticity which requires design change, and being produced in much smaller quantities than ordinary aggregate, production costs are higher. This latter works in a vicious circle to restrict their use and maintain prices that are not competitive, except as against each other. Increased Demand In spite of such handicaps consumption has grown steadily for the past two decades and is apparently growing even faster today. It is evident that lightweight concrete must have better qualities, and be sufficiently better to Overcome the higher cost and the other difficulties and disadvantages pertinent to the use of a new and different material in an old industry. Hence the study of its main ingredient should be of interest to all engineers. Our group has a double interest in the subject since most of the materials which have been used as sources of lightweight aggregate are either mined, Or are by-products of mining operations. We are directly interested in their production as well as their use, and since available supplies of materials suitable are limited, the increasing use, and rising demand, make the discovery of new Or or the development of processes to adapt other natural materials to this use, a promising field; and one in which our profession should take an active part. Recent Development Descriptions of ancient work contain references to the use of spalls of tuffs Or pumice in concrete masonry, but it is only since the nineteen twenties that serious attempts have been made to produce and market lightweight aggregates. A period of rapid advance in theory and practice in cements, mortars and con-

Jan 1, 1948

By Stuart H. Ingram

The term lightweight aggregate implies material which may be substituted for the usual rock, sand and gravel commonly used as the major part of concrete, but distinguished by being much lighter in weight. Background The art of making and using concrete is old and well developed. Research and experience have pretty well determined the qualities necessary in its constituents, and time has tested theories and applications. Elaborate specifications and tests have been devised and generally adopted governing all phases of concrete work, from selection of material, through engineering design and down to mixing and placing. Standard practices have become routine to executives and laborers, and operations have been simplified and costs lowered. Though many lightweight aggregates meet the basic specifications necessary for usefulness, their physical qualities are so different that they fiequently will not pass standard tests, and some of them cannot be mixed and placed with the usual formulas for water and slump. As a rule their use produces a concrete with a lower modulus of elasticity which requires design change, and being produced in much smaller quantities than ordinary aggregate, production costs are higher. This latter works in a vicious circle to restrict their use and maintain prices that are not competitive, except as against each other. Increased Demand In spite of such handicaps consumption has grown steadily for the past two decades and is apparently growing even faster today. It is evident that lightweight concrete must have better qualities, and be sufficiently better to Overcome the higher cost and the other difficulties and disadvantages pertinent to the use of a new and different material in an old industry. Hence the study of its main ingredient should be of interest to all engineers. Our group has a double interest in the subject since most of the materials which have been used as sources of lightweight aggregate are either mined, Or are by-products of mining operations. We are directly interested in their production as well as their use, and since available supplies of materials suitable are limited, the increasing use, and rising demand, make the discovery of new Or or the development of processes to adapt other natural materials to this use, a promising field; and one in which our profession should take an active part. Recent Development Descriptions of ancient work contain references to the use of spalls of tuffs Or pumice in concrete masonry, but it is only since the nineteen twenties that serious attempts have been made to produce and market lightweight aggregates. A period of rapid advance in theory and practice in cements, mortars and con-

Jan 1, 1948

By Arthur C. Simmons

In common with all other producing areas of the United States, Pennsylvania enjoyed increased activity and prosperity during 1937 (Table I). Prices of crude oil were better than for any year since 1930, and the Bradford average was $2.599, compared with an average price of $2.60 in 1930. Production and drilling activities were increased over 1936, although drilling for oil represented almost entirely a program of secondary development in both the water-flood areas and the air-gas repressuring areas. Bradford Oil Field The Bradford oil field continued to produce the major portion of Pennsylvania oil; however, no changes occurred in oil-production methods during 1937. Practically all of the production in the Bradford field is by water-flooding and the total number of oil and water wells completed within the area increased from 3205 in 1936 to 4112 in 1937; an increase of approximately one-third over 1936 completions. The percentage of water wells is approximately one-half of the total completions, although any specific five-spot development will have a proportion of 55 to 60 per cent water wells and 40 to 45 per cent oil wells. Offsetti~ig and boundary oil wells probably will result in a division or percentage of 50 per cent oil and 50 per cent water wells. The quoted figures for well completions include the entire Bradford field, approximately 12 per cent of which is in Cattaraugus County, New York. It is possible to make a segregation of production, but it is not possible to segregate well completions. Production in the Pennsylvania end of the Bradford field in 1937 totaled 15,076,000 bbl., or a daily average of 41,300 bbl. compared with a daily average of 37,000 hbl. in 1936.

Jan 1, 1938

By W. C. Knopf, G. Samsel

For several years International Minerals & Chem-ical Corp. has used a radiation method to assay potassium content of products from potash and feldspar beneficiation. The procedure is rapid, accurate, and inexpensive and is easily handled, if necessary, by nontechnical personnel. Data are presented to show the accuracies that may be expected if the technique is used for control of pilot plants or large-scale plants. Natural potassium is composed of three isotopes —K, K and K. Five other isotopes, artificially produced, have been detected. In natural potassium only the K isotope, with a half life of 1.4x10 years, is radioactive. Its modes of decay are beta and gamma rays, positrons, and x-rays. Only the more abundant beta rays, however, are important in radiation measurements using geiger tubes. Barnes and Salley' measured radiation of potassium salts in solution in 1943. Gaudin and Parnell2 first reported the use of solid salts arranged in a vessel surrounding the ß counter in 1948. Later, Scheel used the method to assay potassium content of various crude and finished potash salts. Experimental: Dip-type Geiger-Muller tubes (TGC-5) supplied by Tracerlab Co. were used in all radiation counting measurements. The tube was encompassed by a glass container about M in. larger in diameter than the tube. This container, which served as a sample holder, was closed at the bottom with a rubber stopper to facilitate removing the samples. Samples were not weighed, but about 40 g of sample were needed for each test. Electrical impulses from the tube were counted on either a Tracerlab scaler or a rate meter. To obviate the need for constant attendance, preset features were incorporated into the scalers, so that at a predetermined time or count the units were automatically deactivated. When rate meters were used, counting rates were read directly from instrument or from a recorder used in conjunction with the rate meter. Each tube was calibrated, according to the manufacturer's instructions, to determine the correct operating voltage to insure reproducible results. A linear calibration plot of percent K2O vs counting rate was also obtained for each tube by recording the counting rate plus background count of several standards of different K2O content chemically analyzed by the chloroplatinate method.' These standards were of approximately the same particle size distribution as samples to be assayed. Specific background count caused by cosmic rays and other surrounding radiation was checked periodically by counting a sample of pure NaCl. Fig. 1 is a representative calibration plot. Assays were determined directly from the standard plot or calculated by subtracting the background count from the counting rate, then multiplying by the slope of the line. Chemical assays of the test samples were made by the Sherril method," a flame photometric technique, or the chloroplatinate method. Data: The radiation assay method has been used for three years by International Minerals & Chemical Corp. in the laboratory and in pilot plants processing ores containing potassium. These dry concentration plants process sylvinite and langbeinite ores at Carlsbad, N. M., and feldspar ores at Top-sham, Maine. Sylvinite ore is predominantly a mixture of syl-vite (impure KCl) and halite (impure NaCl). Contaminants include sulfates, such as langbeinite (2MgSO - K2SO4), kieserite (MgSO H2O), poly-halite (MgSO4.K2SO, 2CaSO, . 2H2O), and slimes. Langbeinite ore is predominantly langbeinite and halite with small amounts of sylvite, sulfates other than langbeinite, and slimes. Several variables, in addition to correct calibration and standardization of tubes, were found to be important in obtaining reproducible results. Particle size distribution of standard samples should be

Jan 1, 1959

By G. C. Wallick, W. R. Foster, J. G. Savins

A comprehensive review of the salient features of the differentiation method of rheological analysis in Poiseuille flow from its inception circa 1928 is presented. Here no initial assumptions regarding the nature of the function relating rheological parameters to observed kinematical and dynamical parameters are required in the data-analysis process. In contrast, the integration method involves interpreting flow properties in terms of a particular ideal model. It is shown that, although both methods represent modes of solution of the same integral equation, being relatively bias-free, the differentiation method offers a more discriminating procedure for rheological analysis. The application to problems involving plane Poiseuille flow is also described. INTRODUCTION In most instances, the approach to the problem of interpreting the rheological properties of various compositions as they are affected by changes in chemical or physical environment, assaying the characteristics of a particular constituent of a suspension, analyzing flow behavior in terms of interactions between components in a system, to cite but a few examples, has been in terms of what Hersey1 terms the integration method. Briefly, it consists of interpreting flow properties in terms of a particular ideal model. The usual practice of the integration method is to choose a model with a minimum number of parameters because, other things being equal, it is desirable to use the simplest model which will describe the behavior of a real material and yet be mathematically tractable for the requirements of data analysis. This expression is then substituted into an equation which relates observed kinematical and dynamical quantities, such as volume flux Q and pressure gradient ], and angular velocity and torque T, in a capillary and concentric cylinder apparatus, respectively. The rheological parameters appear on integrating, in an expression relating the pairs of observable quantities such as those just given. In many instances a particular model provides a good representation of rheological behavior over a reasonable range of compositional and environmental changes. Just as often, however, it is obvious that the interpretation of rheological changes by the integration method is not providing realistic information about changes in flow behavior. A more general method of interpreting rheological data for a given material is to make no initial assumptions regarding the nature of the function relating rheological parameters to observed kinematical and dynamical quantities, e.g., flow rate and pressure drop in capillary flow or angular velocity and torque in a rotational viscometer. This general method Hersey1 terms the differentia-ation method. Instead of integrating, one differentiates the integral equation with respect to one of the limits, i.e., one of the boundary conditions; the resulting expression contains the same observable quantities just given, their derivatives, and the rheological function evaluated at that boundary. By obtaining these derivatives from experimental data, graphically or by a computer routine, they can be substituted into the differential equation and a graphical form of the function derived. THEORY OF THE DIFFERENTIATION METHOD FOR POISEUILLE-TYPE FLOWS In this introductory paper, two flow cases which are important in viscometry are considered (one for the first time) from the differentiation method of analysis, flow in a cylindrical tube and flow between fixed parallel surfaces of infinite extent, the basic integral equations being formulated in a manner analogous to the way they originally appeared in the literature. In addition, the following ideal conditions will be assumed: (1) an absence of anomalous wall effects, (2) isotropic behavior everywhere, and (3) steady laminar flow conditions. Before proceeding it would seem appropriate to preface the analysis of these flow geometries with the comment that the basic philosophy of the differentiation method could be said to stem directly from the efforts of Herzog and weissenberg2 to indicate systematically the various ways of using

By C. T. Eddy

The refining of native copper in the reverberatory furnace, as practiced in the Lake Superior district of Michigan, is very similar to the reverberatory melting and refining of cathodes, but the presence of arsenic in some of the copper concentrates renders the operation somewhat more difficult. Though the copper occurs as the native metal, which is often excep tionally pure—purer, in fact, than after it has undergone refining—its intimate association with the gangue minerals necessitates the cumbersome reverberatory treatment. The gangue consists chiefly of complex silicates of calcium, magnesium, iron, aluminum and sodium, but in certain ore deposits other minerals are often found, among them the native copper arsenides—mohawkite, whitneyite, algodonite and the like. These latter minerals, when present, because of their relatively high specific gravity (7.5 to 8.5), find their way into the concentrates through the gravity concentration processes employed in the recovery of the copper. When such concentrates are melted, the silicates are removed as slag, but, because of the great affinity of molten copper for arsenic, the arsenides dissolve more or less completely in the copper bath. Because of the stability of the resulting melt, the arsenic is tenaciously held in solution. The influence of arsenic on the properties of copper, especially on its electrical conductivity, is generally recognized. For certain uses it is beneficial, and in many instances its presence in limited amounts is not objectionable, but if the metal is to be used for electrical purposes, the almost complete removal of the arsenic is of prime importance. Considerable research has been done on the subject of the influence of arsenic on the electrical conductivity of copperll but the conclusions presented in the literature dealing with the problem show some disagreement. The methods now in use for the removal of arsenic have not

Jan 1, 1931

By K. H. Adams, T. Vreeland

The basal stress-strain behavior, dislocation density, and strain vale sensitivity of the flow stress uqere measured at room temperature on single crystals oj-zone-refined zinc , 99.999 pct Zn, and zinc containing 0.0025 and 0.02 wt pct Al. No significant change in the stvain rate sensitivity of the flow stress occurs with the addition of aluminum. Changes in dislocation substructure and nonbasal dislocation density were obserrled with the addition of aluminum. The effect of aluminum on the basal slress-strain behavior is explained in terms of changes in nonbasal dislocation density which determines the separation distance of junctions between basal and nonbasal dislocations. The onset of basal slip is associated with the breaking of attractive junctions. The chunge in basal dislocation density was found to be proportional to the one-third power of the plastic shear strain, indepedent of purity. THE effect of impurities in solid solution on the stress-strain behavior of single crystals has been the subject of many theoretical studies. These studies have generally concentrated on the interactions between impurities and dislocations to explain the hardening effeet of impurity additions. The theories that have been proposed include those of yott and Nabarro,&apos;l&apos; Cott-re11; Suzuki; and Fisher. In practice, it is generally difficult to predict the relative importance of the vari- ous effects due to impurities. In addition, secondary effects of impurity additions such as induced changes in dislocation density and substructure in the as-grown crystals have received little attention. Many experimental investigations have been conducted on the effect of impurities on the stress-strain behavior of fcc crystals. Hcp crystals have not received much attention except for the extensive work of Levine et a1.= on magnesium alloy crystals. Stuwe~&apos;&apos; has studied the effect of copper impurity on the critical shear stress of zinc crystals and has interpreted the results in terms of the impurity atmosphere model of Cottrell and Jaswon. This report presents the results of an experimental study of the effect of aluminum additions to zinc on the basal stress-strain curve and the strain rate sensitivity of the flow stress. Etch pit techniques were used to measure and characterize the dislocation density and substructure in the zinc alloy crystals. EXPERIMENTAL PROCEDURE Specimen Preparation. Compression test specimens of four different purities of zinc were prepared from CP grade zinc of 99.999 pct purity obtained from the New Jersey Zinc Co. An analysis of this material furnished by the supplier indicated the following impurities in wt ~ct: Pb = 0.0002; Fe = 0.0002; Cd = 0.00005; other <0.60011. A quantity of material of this grade was further purified by zone refining. Zone refining was carried out under a helium atmosphere by passing a double &apos;One furnace Over a 6-ft-10ng charge at the rate of 2 in. Per hr. * total of ten double zone passes were made before the charge was removed from the furnace. The first one third of each charge was used to grow single crystals. Quantities of two

Jan 1, 1969

By M. E. Lombardi

The cost of maintaining the production of an operating oil company is one of the most important, as well as one of the most difficult to estimate, of the various items which go to make up the total cost of producing oil. In the opinion of many operators the cost of drilling and developing new wells, whose, production takes the place of the loss in production through decreased yield of the old wells, is considered an operating expense, for the reason that the total income-producing power of the property is not increased. The cost of these new wells may be added directly to production expense, or it may be charged to capital account, and this account depreciated to the same extent. In either case, after an oil company is on a satisfactory income-producing basis, the money for drilling new wells to maintain production must be taken from the income of the company. Three factors determine the cost of maintaining production: First, the rate of decline in yield of the wells; second, the cost of drilling and equipping new wells in terms of their production; third, the decrease in initial production of new wells as the property is drilled and gas pressure taken off the sands, etc. In order to check theoretical figures for the cost of maintaining production the writer, with the assistance of Reed Bush and Fred Tough, has compiled the following figures. It is necessary first of all to choose a&apos; period of time during which production for the field or territory studied remains fairly constant. The longer the period of time over which this condition prevails, the better. It is also necessary to eliminate or allow for any extraneous condition which may have affected the production returns, such as the shutting down of a large number of wells, the bringing in of a well of exceptionally large yield, the opening up of virgin territory where the flush yield is greater than will be had from new wells in after years, etc. All these conditions are exemplified most simply in the case of the Coalinga field, and perhaps these figures are more truly prophetic than the two other cases given. In applying these figures to the future it is well to assume that the average yield of new wells will constantly de-

Jan 1, 1916

By Alton B. Cook, G. B. Spencer, F. P. Bobrowski

In estimating production gas/oil ratios and oil recoveries from reservoirs containing highly volatile oils it is highly important to include condensate that may be recovered from the gas produced from the reservoir. The volume of the hydrocarbon liquid condensed from the production of the solution gas that has been liberated. in some reservoirs may equal or even exceed the volume of recoverable stock-tank oil as estimated by present methods. The usual procedure1, 2, 3 in estimating future reservoir performance includes use of relative permeability data of the reservoir rock to gas and oil and includes material-balance calculations utilizing data on the volume of the reservoir fluids, oil and gas production and reservoir pressure decline, and data on the physical properties of the initial reservoir fluids. The inaccuracy in the procedure results from the false assumption that all of the free or liberated gas that enters the well bore of reservoirs containing highly volatile oils remains in the gaseous phase as it is produced. This paper presents a method for estimating future reservoir performance and oil recoveries based on special labora. tory analyses of reservoir-oil samples and recognition of the additional volume of hydrocarbon liquid that will be recovered at various stages of depletion from a solution.gas.drive reservoir. The method also includes calculations of the volume and composition of the hydrocarbon liquids that can be recovered by processing the produced gas in a natural-gasoline plant. The development of the method resulted from a study of laboratory analyses of reservoir samples and of field data obtained from two reservoirs containing oil of the highly velatile type. Relatively high pressures and temperatures prevail in oil reservoirs discovered at the greater depths of present-day drilling. The contained fluids may have high saturation -Dressures and large volumes of gas in solution. The oils and gases under these conditions may be almost identical in compositions and densities.4,5 Also, engineers have noted that, for a number of oil reservoirs and especially the deeper reservoirs, the API gravity of the stock-tank oil increaees as the production gas/oil ratios increase. They attributed this increase in API gravity of the stock-tank oil to the formation of condensate as the liberated gas in the reservoir is being produced. SOURCE OF DATA FOR CALCULATIONS Subsurface oil samples and well-test data were obtained from the E. Constantin-Lambert Well No. 1 in the Elk City Field, Okla., to demonstrate the need for and a method of calculating future reservoir performance when consideration is given to the recoverable hydrocarbon liquid from the production of solution gas that has been or will be liberated in a reservoir. The Lambert well is located in C, SW 1/4, SW 1/4, Set- 18, T-l0-N, R-20-W, Washita County, Okla. At the time of completion it was on the east edge of the development and Was producing from conglomerate through 30 perforations in the 5 1/2-in. casing at a depth of 9,859 to 9,864 ft. The well Was completed on July 9, 1949, and subsurface oil samples were obtained July 29 and August 1, 1949. Production gas/oil ratio data were obtained during the operation in series of two Separators at high and low-pressures of 314 and 44 psia, respectively, and at an average temperature of approximately 60°F. The flowing bottom-hole pressure at the time of sampling was 3,934 psis. The static bottom-hole pressure was not obtained at the time of sampling, as the well could not be shut in long enough for testing because gas produced from the well was used for fuel at an offset drilling well. However, the initial reservoir pressure was calculated to be 4,364 psia from knowledge of pressure gradients in other wells in the field and the depth of the casing perforations in the Lambert NO. 1 well.

Jan 1, 1951

By K. T. Aust

The relative interfacial energies of symmetrical tilt boundaries in silver of greater than 99.999 pct purity were measured as a function of orientation difference 0 between 9° and 36° about <001>. The results are in good agreement with the dislocation model of the grain boundary. The energy vs H curve may be represented by the Shockley and Read equation in the form Eoe (0.55—In 8). READ&apos; has indicated that an ideal experimental method of testing the predictions of the dislocation theory of the grain boundary would be to measure the interfacial energies of symmetrical tilt boundaries between face-centered-cubic grains that have a common <001> axis, as a function of orientation difference 0. The misfit H should be defined by a rotation of each grain through an angle of H/2 away from the boundary. Such boundaries might be expected, from geometrical considerations, to be made up of a series of edge dislocations, at least for small values of 0. Energy vs H relationships for tin&apos; and lead:&apos; were previously obtained for an asymmetrical tilt boundary separating two grains in which generally only one grain was rotated about a <001> specimen axis through an angle of H away from the boundary, the other grain remaining fixed. It is possible, however, that the boundary atoms in tin and lead may have attained a symmetrical position, in relation to the orientations of the grains on either side of the boundary, during equilibrium annealing. The two sets of measurements on silicon ferrite&apos; were somewhat better suited for comparison with theory, since the boundaries were symmetrical tilt boundaries in which the axis of relative rotation was <110> in the first series and <l00> in the second; but this alloy has a body-centered-cubic structure. Although the grain boundaries in silver" were symmetrically tilted, the axis of relative rotation was not a simple crystallographic direction, and it varied from boundary to boundary. Although the above measurements were in good agreement with the Shockley and Read equation,"&apos;: it appeared desirable to carry out experiments under the ideal conditions specified by Read.&apos; Consequently, the relative energies of symmetrical tilt boundaries in silver between grains that have a common <001> axis were measured. The technique of equilibrating grain boundaries in oriented tricrystals was used rather than the less satisfactory thermal groove method previously employed for silver bicrystals." Experimental Details and Observations The solidification and seeding techniques, described previouslyh for growing tricrystals of controlled orientations, were used to prepare tricrystal specimens from silver of greater than 99.999 pct purity. The silver was obtained from American Platinum Works, Newark, N. J., in the form of poly crystalline rods 10 cm long and 7 mm in diam. These rods were then cold worked by rolling or drawing them into suitably shaped blanks. Single crystal seeds and tricrystals were grown in a high purity graphite boat by means of a movable furnace with globar heating elements. The graphite boat was enclosed in a Vycor tube, which was first evacuated to about l00/u Hg and then filled with a static argon atmosphere. The maximum temperature outside the Vycor tube was 1250°C. A typical tricrystal specimen of silver is shown in Fig. 1. Grains B and C were grown from seed crystals with a <001> specimen axis or longitudinal direction parallel to the direction of growth and with another <001> direction perpendicular to the surface. Each of the two seed crystals was rotated 18" about the <001> specimen axis but in opposite directions away from the boundary. A symmetrical tilt boundary, therefore, separated grains B and C with an orientation difference 8 of 36" about <001>. Grain A in Fig. 1 was grown from the middle seed with a <110> direction parallel to the specimen axis and with a <001> direction inclined at 45&apos; to the surface of the specimen. The interfaces sepa-

Jan 1, 1957

By F. P. Bobrowski, G. B. Spencer, Alton B. Cook

In estimating production gas/oil ratios and oil recoveries from reservoirs containing highly volatile oils it is highly important to include condensate that may be recovered from the gas produced from the reservoir. The volume of the hydrocarbon liquid condensed from the production of the solution gas that has been liberated. in some reservoirs may equal or even exceed the volume of recoverable stock-tank oil as estimated by present methods. The usual procedure1, 2, 3 in estimating future reservoir performance includes use of relative permeability data of the reservoir rock to gas and oil and includes material-balance calculations utilizing data on the volume of the reservoir fluids, oil and gas production and reservoir pressure decline, and data on the physical properties of the initial reservoir fluids. The inaccuracy in the procedure results from the false assumption that all of the free or liberated gas that enters the well bore of reservoirs containing highly volatile oils remains in the gaseous phase as it is produced. This paper presents a method for estimating future reservoir performance and oil recoveries based on special labora. tory analyses of reservoir-oil samples and recognition of the additional volume of hydrocarbon liquid that will be recovered at various stages of depletion from a solution.gas.drive reservoir. The method also includes calculations of the volume and composition of the hydrocarbon liquids that can be recovered by processing the produced gas in a natural-gasoline plant. The development of the method resulted from a study of laboratory analyses of reservoir samples and of field data obtained from two reservoirs containing oil of the highly velatile type. Relatively high pressures and temperatures prevail in oil reservoirs discovered at the greater depths of present-day drilling. The contained fluids may have high saturation -Dressures and large volumes of gas in solution. The oils and gases under these conditions may be almost identical in compositions and densities.4,5 Also, engineers have noted that, for a number of oil reservoirs and especially the deeper reservoirs, the API gravity of the stock-tank oil increaees as the production gas/oil ratios increase. They attributed this increase in API gravity of the stock-tank oil to the formation of condensate as the liberated gas in the reservoir is being produced. SOURCE OF DATA FOR CALCULATIONS Subsurface oil samples and well-test data were obtained from the E. Constantin-Lambert Well No. 1 in the Elk City Field, Okla., to demonstrate the need for and a method of calculating future reservoir performance when consideration is given to the recoverable hydrocarbon liquid from the production of solution gas that has been or will be liberated in a reservoir. The Lambert well is located in C, SW 1/4, SW 1/4, Set- 18, T-l0-N, R-20-W, Washita County, Okla. At the time of completion it was on the east edge of the development and Was producing from conglomerate through 30 perforations in the 5 1/2-in. casing at a depth of 9,859 to 9,864 ft. The well Was completed on July 9, 1949, and subsurface oil samples were obtained July 29 and August 1, 1949. Production gas/oil ratio data were obtained during the operation in series of two Separators at high and low-pressures of 314 and 44 psia, respectively, and at an average temperature of approximately 60°F. The flowing bottom-hole pressure at the time of sampling was 3,934 psis. The static bottom-hole pressure was not obtained at the time of sampling, as the well could not be shut in long enough for testing because gas produced from the well was used for fuel at an offset drilling well. However, the initial reservoir pressure was calculated to be 4,364 psia from knowledge of pressure gradients in other wells in the field and the depth of the casing perforations in the Lambert NO. 1 well.

Jan 1, 1951

By S. P. Kinney, C. E. Wood, T. L. Joseph

In connection with its investigations of the blast-furnace process, the Bureau of Mines, in cooperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferroman-ganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the cooperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests. The Aluminum Co. of America was interested in knowing the practicability of smelting a charge of bauxite, iron ore, and limestone, of proportions that would produce slag of the following composition: A1203, 47 to 48 per cent.; CaO, 41 to 42 per cent.; SiO2,4 to 5 per cent.; TiO2, 2 to 3 per cent.; FeO, 1 percent., and MgO, 1.8 percent. In addition to determining whether it was feasible to operate a blast furnace on slag approaching the composition given above, a quantity of slag was needed for a series of experiments that would show the relative ease and cost of extracting alumina from slag which could be made in the blast furnace, as compared to extracting it from raw bauxite. The value of the slag as a raw material

By L. B. Ticknor, M. B. Bever

An isothermal calorimeter suitable for measurements of heats of solution in liquid tin as solvent is described. Measurements of the heats of solution of gold, silver, copper, and a gold-silver alloy are reported. The heat of formation of this gold-silver alloy is also reported. HEATS of solution in liquids can be determined directly, but few such data have been published for metals as solvents. Knowledge of heats of solution is desirable because it contributes to the general understanding of energy relations in metallic solutions. Thermochemical measurements of this type also furnish answers to specific problems: For example, from the heats of solution of an alloy and of a mixture of its constituent elements in a given solvent, the heat of formation of the alloy may be found. Similarly, differences in the energy content of samples of the same metal in two different states, such as the annealed and cold worked states, may be determined. In the work reported here, gold, silver, and an alloy of gold and silver were dissolved in liquid tin at 240°C and gold, silver, and copper were dissolved in tin at 300 °C. The experiments yielded the heats of solution of these metals in tin. The heat of formation of the gold-silver alloy was also determined. The same calorimetric method is being used to measure the energy stored in metals during cold working and preliminary results have been published.&apos; Equipment and Experimental Procedure The isothermal calorimeter used in this work, Fig. 1, consisted of a Dewar flask completely immersed in a constant-temperature salt bath. A long neck provided space for thermocouple leads and a stirrer shaft and permitted the injection of solute samples. The metal bath in the calorimeter flask was stirred at about 100 rpm by a small glass impeller driven by a constant-speed motor. The shaft of the stirrer passed through a Wilson vacuum seal.2 All measurements were made under vacuum in order to eliminate temperature disturbances resulting from gas convection and to prevent the oxidation of tin. The calorimeter flask was joined by an all-glass connecting line to a gas-control system which made possible the use of a protective atmosphere of deoxidized and dried hydrogen. At the operating temperature of the calorimeter tin oxide was not reduced by hydrogen, presumably because the reaction rate was too slow. Part of the closed system was a removable side tube through which the solute sample could be introduced and in which it was held at a temperature of 0°C prior to injection into the metal bath. The salt bath containing a mixture of sodium, lithium, and potassium nitrates was similar to that described by Beattie3 and was equipped with a stir-

Jan 1, 1953

By A. E. Dwight

Lattice parameters were determined for eighteen equiatornic alloys of the CsCl-type structure, ten of which were previously un-reported. It was found that fomation of the CsCl-type structure in binary alloys of the transition elements is largely dependent on position of the elements in the periodic table. The relative size of the two elements was not found to be a controlling factor. A recent paper by Beck, Darby, and Arora1 corre-lates the occurrence of CsC1-type ordered structures with the position of the constituent elements in the periodic table for the first long period. It was also suggested that a definite increase in relative bond strength between unlike atoms occurred when, in binary alloys of iron-group elements, the other component is changed from a chromium-group element, to a vanadium-group element, to titanium. A later paper by Philip and Beck2 noted that the lattice contraction increased in the order CrFe, VFe, and TiFe. It was also noted by Philip and Beck2 that the lattice contractions of CsC1-type alloys decreased in the order: TiFe, TiCo, and TiNi, which is an apparent reversal of the contractions expected from the position in the periodic table. It was suggested that the increasing lattice contraction is an indication of increased stability, i.e., greater A-Bbond strength. The present investigation was carried out to determine whether the relation of the position in the periodic table to the formation of the CsC1-type structure was also correct for alloys involving the second and third long-period elements. A systematic search was made for CsC1-type structures among equiatomic alloys and for those found, the lattice contraction was determined. EXPERIMENTAL TECHNIQUE The elements Y, Gd, Ti, Zr, Hf, V, and Cb are designated the A group and the elements Mn, Re, Fe, Ru, Os, Co, Rh, Ir, Ni, Pd, Pt, Cu, Ag, and Au are designated the B group. Equiatomic alloys were prepared for 57 AB combinations. The alloys were arc melted in a multicrucible furnace3 in buttons ranging from 5 to 20 g. Chemical analyses were not made, as the charge weights agreed closely with those of the buttons after melting. The alloy buttons were homogenized at 800° to 900°C. Metal log raphic and X-ray specimens were prepared and heat treated at temperatures from 600° to 1200°C. Specimens for X-ray diffraction were usually ground to a powder in an agate mortar; however, needle-shaped solid specimens were used when the alloy was sufficiently ductile to permit their preparation. Diffraction patterns were taken with a Straumanistype Debye-Scherrer camera using filtered Cu or Co radiation. The lattice parameters were obtained in A by plotting the calculated a0 values against the cos29/sin 0 + cos2?/? function and extrapolating linearly to ?= 900. Metallographic control specimens were polished on cloth wheels with diamond paste and etched with various phosphoric and nitric acid reagents. RESULTS The eighteen equiatomic alloys listed in Table I gave evidence of a cubic structure with two atoms in the unit cell, although two of these cubic structures exist only at elevated temperatures and transform to a tetragonal structure on quenching. Nine of these eighteen alloys gave diffraction patterns with super-lattice lines showing that the structure is of the CsC1-type. The lack of superlattice lines in patterns of the other nine alloys may be attributed to the small difference in atomic scattering power of the components. Metallographic study indicates the occurrence of nine narrow single-phase fields at the AB composition. Any or all of these nine may also have a CsC1-type structure. The VFe alloy was found to have a CsCl-type structure by Philip and Beck2 through the use of CrKa radiation (for which the scattering factor of V is anomalously low), whereas the Cu radiation used

Jan 1, 1960

By Francis Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world&apos;s largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other indus-tries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020&apos;s and low 0.030&apos;s; silicon content must be held within a very narrow range, and definite requirements of phos-phorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater impor-tance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appear-ance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1935

By J. G. Faller, L. P. Skolnick

The distribution of cobalt and vanadium over non-equivalent crystallographic sites in C14-type Zr(VCo), alloys has been investigated. An anomalous X-ray scattering technique developed by Skolnick, Kondo. and lavine7 by which the separation in the scattering factors of two similar atoms can be enhanced was employed. Six alloys spanning the pseudobinary section ZrV1.6Co0.4-ZrVO.6CO1.4 at 10pct steps showed a nonrandom compositionally dependent distribution. Specifically, at high vanadium content cobalt preferentially occupied sites of type (6h) and vanadium, sites of type (2a; at low vanadium content the reverse was observed. In addition to the distribution fraction the structural parameters x and z were obtained. There was no significant deviation of these parameters from those obtained in the ideal C14 structure. Certain suggestions are made to account for the observed nonrandomness in the distribution of atoms on the two types of sites. INTERMETALLIC compounds of formula AB2 iso-morphous with MgCu2, MgZn2, and MgNi2 are known as Laves phases. Because Laves phases exhibit high symmetry and coordination numbers, the highest possible for an AB2-type compound,1 they are among the most frequently observed compounds in nature. In recent years interest has centered about the purely transition metal Laves phases2-&apos; in efforts to understand the function of atomic size and electronic structure in the formation of these compounds. It has been observed that pseudobinary Laves phase systems often show a variation of structure across the phase diagram. Such a system is the ZrV2-ZrCo2 in which the structure varies from cubic MgCu2 to hexagonal MgZn2 to cubic MgCu2.4 Some understanding about the conditions under which the second modification is stable can perhaps be gained by studying the distribution of cobalt and vanadium atoms on lattice sites in the MgZn2 modification of the system ZrV2-ZrCo2. In both the MgZn2 and MgNi2-types there exist nonequivalent positions open to occupancy by the B element, whereas in the MgCu2 prototype all sites are equivalent. Skolnick, Kondo, and La-vine7 have developed an anomalous scattering technique suitable for this type of investigation. Whereas the influence of size on the formation of a Laves phase is well recognized, no substantial evidence has been put forth in support of the size ratio dependence of a particular prototype. Berry and Raynor8 suggested that RA /RB ratio does indeed affect the type of structure that is chosen, MgZn2 compounds tending to cluster about 1.225 while MgCu2 compounds were found at larger deviations from this ratio. Dwight,3 however, from a study of 164 Laves phases does not believe this generalization to be justified. Electronic effects are certain to play a part in the stability of Laves phases in general and in the choice of a structure type in particular. For example, size along would favor the formation of Laves compounds of Ti, Zr, Hf, Ta, or Nb as the A element with nickel or copper as the B element. The absence of such is attributed to an unfavorable electron : atom ratio by Elliott and rostoker.4 Early experiments of Laves and witte9 with pseudobinary and pseudoternary systems of the three prototypes established the dependence of crystal structure upon electron: atom ratios. They observed that the MgCu2 structure dissolved elements of higher valency until the electron: atom ratio of =1.8 was reached; the MgZn2 likewise dissolved elements of lower valency replacing zinc. witte,6 from calculations of the electron : atom volumes of Brillouin Zones, obtained limits of stability for the prototypes MgCu2 and MgZn2. Elliott and Rostoker4 used these limits with considerable success in the all-transition element Laves phases they investigated. According to witte,6 compounds between the electron :atom ratios of 1.80 and 2.32 were of the MgZn2 type; those above and below exhibited the MgCu2-type structure. On the basis of these limits and an assumed valency of zirconium based upon the near tetra-valence of titanium, Elliott and Rostoker obtained valencies for the first transition series elements. For the Laves phases with which this investigation is concerned, ZrV2 and ZrCo2, the authors calculated electron :atom ratios of 2.54 and 1.56, respectively. These ratios are for the MgCu2-type structure and straddle the stability band of the MgZn2 modification. One could, therefore, predict that a pseudobinary system ZrV2-ZrCo2 should pass through the MgZn2 modification in traversing the composition diagram from one end to the other. Implicit in this assumption is a smooth change of the electron: atom ratio from 2&apos;54 to 1.56. MOSS10 states that his finding the low temperature structure of ZrCr2 to be C15 instead of C14 alters greatly Elliott&apos;s valency of zirconium and hence the assumed valencies of the other metals. Such a quantitative correlation of structure with electron : atom

Jan 1, 1963

By R. J. Schilthuis, T. V. Moore

In a previous paper,&apos; the results of some experimental work on the measurement of slippage in the flow of oil and gas mixtures through vertical pipes were presented. The data obtained were correlated and equations were deduced from which the performance of the experimental gas-lift could be predicted with reasonable accuracy. However, attempts to apply the equations to the calculation of pressure drops in actual flowing wells yielded erroneous results. At the time the results of the experimental work were published, no satisfactory explanation could be offered for the failure of the empirical equations to express properly the performance of wells. However, recent work has led to the development of a new hypothesis which presupposes certain conditions affecting the flow of oil and gas in wells. When the proposed equations are corrected to allow for these conditions, an agreement between the observed and calculated performance of the actual wells is obtained which in most cases is quite satisfactory, although it is subject to certain limitations. In this paper, the method of calculating the pressure drop in actual wells is considered, and the application of the method to the design of tubing is discussed. (For nomenclature used in this discussion, see Table 1.) Factors Affecting Slippage and Efficiency At the outset, a few of the principle factors affecting slippage and efficiency in the gas-lift discussed in the previous paper will be reviewed. In the flow of the mixture of oil and gas in a vertical pipe, slippage is the phenomenon of gas moving upward with a. linear velocity greater than that of the oil. Under steady conditions, if given quantities of oil and gas enter the tubing per unit of time, the same quantities of oil and gas per unit time must, on the average, pass every section of the tubing; otherwise, there would be accumulation or depletion of the oil or gas at some sections, and the flow would be unsteady. Therefore, if the gas is to flow at a greater linear velocity than that of the liquid,

Jan 1, 1933

By J. C. Mertz

ACCURATE knowledge of the solid solubilities of the elements that dissolve in the important base metals is needed for guidance in the preparation and heat-treatment of the alloys derived from these compo-nents. While there is still difference of opinion concerning the merits of the X-ray and microscopic methods of determining such solubilities, it is certainly true that the recent extensive use of X-ray diffraction to review the existing constitutional data has revealed many glaring inaccu-racies and has brought about a much improved knowledge of phase-boundary locations, which will inevitably come to include all of the important alloy systems. When the work is done with all necessary precautions it appears that in the majority of cases where the solubilities extend beyond a few tenths of a per cent the X-ray back-reflection technique is capable of furnishing the best of information in this field. For the most prolonged and thorough studies it is obviously advisable to combine the results of several methods, in particular, to obtain an agreement between X-ray and microscopic data. This paper reviews the work previously done on the solubilities of phosphorus, arsenic, antimony and bismuth in copper and, in considera-tion of the uncertainties thus made apparent, presents, new X-ray data obtained with the first three members of this group.

Jan 1, 1936