Search Documents

By C. A. Heiland

Geophysical methods are playing an ever increasing part in various engineering fields. About ten years ago, geophysical exploration was first applied in civil engineering to the study of foundations and the location of construction materials and water. Its usefulness is now being extended into the field of structural engineering. Almost every structure has to be so designed that it will withstand any force to which it may be subjected. Such forces may result from its own weight, applied loads, pressures of various kinds, including those due to wind and water, ground subsidence and vibrations. The last two, problems involving the nature and dynamic behavior of surface and subsurface formations, are within the scope of geophysical investigations. In the design of any structure, the disposition and dimensions of its members as well as their materials must be so selected that they will withstand any or all of the forces enumerated above. In other words, its "resistance" to such forces must be sufficient, allowing for a definite margin of safety. Often a static treatment of the problem leads to satisfactory results, but the static method entails serious errors when vibrations are involved, as in resonance with an impressed vibration the displacements of a structure or parts thereof may dangerously exceed the allowable values. The principle of "dynamic design"† is, therefore, avoiding or reducing resonance by suitable selection of the natural frequency of a structure, or by the provision of damping. Methods of Investigation Dynamic design of structures is required where ground vibrations occur naturally or are produced artificially. Earthquake regions fall in the first group; areas of industrial activity where vibrations are produced by machinery, blasting, etc., fall in the second. In either case, dynamic

Jan 1, 1940

By M. Yoshinuga, S. Watanabe

Some iron ores, sinters and pellets occasionally show abnormal behavior during reduction which makes them undesirable as blast furnace burden. These may be divided into the following three types: (1) decrepitation of iron ore, (2) swelling of iron ore and pellet, (3) size degradation of sinter. In this paper reduction experiments and microscopic examinations were made to clarify the mechanisms and causes of these abnormal phenomena. Decrepitation occurs mainly when compact hematite ores containing small amounts of limonite are heated to about 500°C. Abnormal swelling of ores and pellets is caused by the rapid growth of fibrous metallic iron from the surface of wustite grains during rapid reduction and is fundamentally related to their original microstructure. Size degradation of sinter occurs through the development of cracks in the reduction stage from hematite to magnetite. About 80% of the iron ore used in Japan's blast furnaces comes from abroad, and the iron and steel industry must import this raw material from distant overseas places at high freight rates. The blast furnace operators, therefore, have made strong efforts to cut costs under these restrictive raw materials conditions by increasing productivity and simultaneously decreasing coke consumption. If, however, a high proportion of the ore burden consists of unsuitable materials furnace irregularities often result, establishing the need for detailed investigations of the basic natures of the ore constituents and their reactions during the reduction process. Recent investigations '-' of various ore burdens suggest that some iron ores, sinters and pellets are occasionally abnormal in appearance and behavior during reduction studies and may prove to be undesirable for use in the blast furnace. In the present study reduction experiments and microscopic observations were made to clarify the causes and the mechanisms of the abnormal behavior observed in some constituents of the burden and their effect on blast furnace performance. REDUCING APPARATUS The four kinds of reducing apparatus used in this investigation were the following: 1. The JIS* (Modified Gakushin') apparatus shown in Fig. la is most commonly used in Japan to evaluate the reducibility of ores under static conditions. It consists of a stainless steel tube of 60 mm inside diam suspended from a balance. 2. Linder's Reduction Test apparatus (Fig. lc) has a reducing barrel 130 mm diam and 200 mm long which rotates at 30 rpm. Some modifications were made in test procedures. 3. Gakushin Standard Test apparatus for determining the reducibility of granular ores (Fig. Id) consists of a horizontal silica tube 32 mm diam, 370 mm long and a movable electric furnace which enables rapid heating and cooling of the specimens. 4. The test apparatus for reduction under load (Fig. lb) gives a comprehensive evaluation of the behavior of ores under conditions simulating the static loading and the chemical reduction conditions encountered in. a blast furnace stack. A stainless steel tube of 50 mm diam and a carbon rod of 35 mm diam were used as the sample container and the support for the weight, respectively. In each investigation care was taken to select the most suitable method and apparatus to distinguish the abnormal nature of the ore in question. SIZE DEGRADATION OF SINTER DURING REDUCTION Sinter makes up the major portion of the blast furnace burden and its behavior during reduction should bear a close relationship to the iron productivity. Recently, some of the sinter was found to show serious size degradation during reduction at a relatively low temperature range. Because this phenomenon was thought to be a possible source of furnace irregularities, tests were made to clarify the phenom-

Jan 1, 1969

By T. A. Rickard

In a former paper* the writer has described the essential features of the general geology of the Cripple Creek region. In the present account it is intended to examine into the occurrence of the ores, the value of which has made this district the most important among existing American gold-fields. The production of Cripple Creek from its discovery, in 1891, to the close of 1901, has reached a valuation of fully $125,000,000. During the past year (1901) the output amounted to $17,285,470. In 1900 it was $18,174,681. The first discoveries, which led to the development of the district, were made in the spring of 1891, but it was not until 1893 that vigorous work was commenced. A great impetus was then given to the exploration for gold on account, of the sudden drop in the market-price of silver, caused by the closing of the Indian mints in the summer of that year. This induced an energetic population from the older silvermining camps of Colorado to go to the new gold-field, which was then beginning to attract attention. Prospecting, at first, was hindered by the comparative absence of outcrops, due to the fact that the surface of the hills is covered with a considerable thickness of shattered rock, resulting from the action of frost at a high altitude; but so much indiscriminate digging was done that a number of rich veins were uncovered, and this stimulated the search for others. The advanced condition of the mining industry of Colorado offered unusual facilities for exploration and reduction; progress was therefore rapid, with the result that the district soon achieved great prominence.

Jan 1, 1903

By T. N. Rhodin

There can be two types of films on solids, those which are stable in mono-layers and those which tend to aggregate into three dimensional structures. A great number of metal films formed by condensation onto a solid base are unstable in the sense that they will aggregate into crystals providing the atoms possess sufficient surface mobility. The crystalline structure of the film is strongly influenced by the base in many systems and, in some cases, a single orientation prevails when the force fields around the atoms in the supporting crystal are sufficiently strong.' Relatively little is available in the literature about the nature of these forces and the role they play in promoting a preferred orientation of the atoms arriving at the substrate surface. An understanding of their periodicity and magnitude relative to the surface forces characteristic of the film itself should provide insight into the critical dependence of film orientation on the nature and temperature of the substrate. In addition, this effect may be very useful in preparing samples for surface studies. The study of the physical and chemical characteristics of pure metal surfaces has been severely handicapped by the presence of strongly adherent foreign films. Furthermore, the randomness of the surface orientation has obscured interpretation of experimental results. Evaporation of metals in high vacuum onto carefully selected substrates under ideal conditions for preferred orientation appears suited to the preparation of flat, oxide-free, oriented films for surface reaction studies. Many factors influence their structure and some understanding of the mechanism of their formation is a necessary prerequisite for obtaining satisfactory surfaces for study. The dominant factors in defining film structure are film thickness and growth rate and the nature, condition, and temperature of the substrate. GENERAL ASSEMBLY The system was enclosed in an 18 in. bell jar which rested on an L-shaped neoprene gasket on a ground steel plate as indicated in Fig 1. Rapid evacuation of the system to 10-6 mm mercury was facilitated by a 4 in. manifold, 2 in. packless valve, and an extra large diffusion pump. Suitable arrangement of valves on a secondary manifold readily permitted introduction of purified gases

Jan 1, 1950

By R. W. Raymond

THE absence of a convenient glossary of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as may be inferred from its great increase in length, as well as the numerous alterations which it has undergone. It could certainly be still further enlarged and improved; but I think a comparison of it with any of the glossaries of the same class now in print will show, at least, that it is an advance upon what has hitherto been accomplished. 1 shall be grateful, however, for further criticisms and suggestions; and I purpose at some future time to incorporate in a supplementary paper the results of such additional collections or corrections as I may obtain. To avoid too great prolixity, I adopted at the outset the following general principles: 1. To include the most important technical words and phrases used by American miners and metallurgists, or occurring in English books and periodicals.

Jan 1, 1881

By B. W. Gonser, C. M. Heath

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By C. M. Heath, B. W. Gonser

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By J. L. Bruce

AFTER six years of war-enforced idleness, Cyprus copper mines are operating again. This relatively long shutdown seems infinitesimal when compared with something like seventeen hundred years of inactivity that followed the important operations of the ancient Romans, and continued until the twentieth century. The historical records of the ancient operators are scarce but full of interest to those who realize that Cyprus copper production was important more than two thousand years ago. This paper, however, will give only a brief review of the ancient history and the evidence of ancient mining which have been quite fully covered in other publications.1-6 The purpose of this paper is to give a general sketch of the Cyprus Mines Corporation's enterprise in the Island of Cyprus, with special emphasis on those conditions and practices which are unusual. The picture is not intended to be complete, and many interesting details will be omitted. Some of these may be described in subsequent papers covering departmental practices. The principal operations of Cyprus Mines Corp. are in Cyprus, where it has leasehold concessions from the Cyprus Government covering about 50 square miles. It holds additional areas under "Prospecting Permits." The consideration for the concessions is a royalty on production, coupled with minimum annual rentals. Cyprus is a British Colony in the Eastern end of the Mediterranean with an area of about 3000 square miles and a population of about 400,000, of which 65 pct may be classed as Greeks on the basis of language, religious training, and traditions. About 25 pct are Moslems, principally of Turkish extraction. Prevailing languages are Greek and Turkish. A large proportion of the supervisory and administrative staff and practically all of the skilled and unskilled craftsmen and laborers are drawn from the native population. The "overseas" staff constitutes not more than 2 pct of the employees. The majority of these are from the United Kingdom, the British Dominions and Colonies. About one-third are from the United States of America. The topography of the Island is rugged, with mountains and foothills covering more than two-thirds of the area. Between the Kyrenea range rising to 3000-ft elevation, along the north coast, and the Troodos range (maximum elevation 6400 ft) occupying the southwest half of the Island, lies a cultivated rolling plain, the "Mesaoria," dry in summer and watered only by the winter rains and by scanty irrigation from small mountain streams and wells in the spring and summer. Climate and natural vegetation are characteristic of semi-arid conditions. The "urban" population, about one-fourth of the total, lives in the five port towns, Famagusta, Larnaca, Limassol, Paphos and Kyrenia, and in the capitol Nicosia, near the center of the Island. The suburban population lives almost entirely in villages or small towns, with very few people residing in isolated country homes.

Jan 1, 1947

By Arthur Winslow

Location.—The Liberty Bell gold-mine is in the San Juan region, in the southwestern corner of Colorado. It is situated about 2 miles from the town of Telluride, near the summit of the Uncompahgre range, at the head of Cornett basin, at an altitude of 11,000 feet, and in a district of excellent record in the past and of great promise for the future. In the immediate vicinity are such well-known and important mines as the Smuggler Union, with a total production of over $12,000,000; the Virginius and Revenue Tunnel group, with a production of probably $5,000,000; the Tom-Boy, with a production of probably at least $3,000,000; the Japan, the Cimarron, and a number of others. History.—The first prospecting in this district is reported to

Jan 1, 1900

By C. H. Li, R. J. Stokes

This paper compares the fracture behavior of tungsten rods in three conditions: recrystallized. recovered, and wrought. Notched specimens suhjected to a 50 in.-lb impact load showed ductile-brittle transitions at 700, 4.90°, and 440°C, respectinely. The recrystallized material had an equiaxed pain structure and jracbred by simple cleavage from a grain boundary source at all temperatures up to 700°C. The wrought and recovered material had an elongated fibrous structure and at low temperatures fractured by cleavage originating from the notch. As the transition temperature was approached cleavage was preceeded by more and more intergvanular splitting which deflected the crack front into planes parallel to the tensile axis. The enhanced toughness of wrought and recovered tungsten was attributed both to its inability to initiate cleavage because no pain boundaries were suitably oriented perpendicular to the tensile stress and to its inability to maintain cleavage because of intergranular splitting ahead of the crack. It has been appreciated for a long time in a qualitative manner that the room-temperature brittleness of fully recrystallized tungsten may be alleviated by working the material at relatively low temperatures.' More recently this difference in mechanical behavior between wrought and recrystallized tungsten has been examined quantitatively by measurement of the tensile properties as a function of temperature. In these experiments brittleness has been expressed in terms of ductility or reduction in cross-sectional area upon tensile fracture or in terms of the bend radius before fracture under bending.' This work has shown the existence of a fairly sharp transition from brittle to ductile behavior with an increase in temperature. The ductile-brittle transition temperature for recrystallized material is approximately 200°C higher than for wrought material. An increase in strain rate, small additions of impurity,' or an increase in grain size4 shift the respective transition temperatures to higher values, but the difference between them remains approximately the same at 200°C. A number of explanations for this embrittlement by recrystallization have been given. It has been blamed either on the concentration of impurity at the grain boundaries, the increase in grain size, or the change in texture which occurs upon recrystallization. The present paper examines the effect of different heat treatments on the notch-impact behavior of commercial powder-metallurgy tungsten rods. The change in the ductile-brittle transition temperature for this method of loading and the fracture mode has been related to the different mi-crostructures produced by heat treatment. EXPERIMENTAL PROCEDURE Commercial swaged powder-metallurgy tungsten rods 1-3/8 in. in length and 1/8 in. in diameter were machined to introduce a sharp V notch 0.030 in. deep. To change the microstructure from that of the as-received wrought material some of the specimens were subjected to an anneal in nitrogen either at 1300° or 1400°C for 8 hr or at 1600° or 2000°C for 1/2 hr. The notched rods were then placed in a miniature Charpy-type impact machine and struck at their midpoint (opposite the notch) with a hammer designed to deliver 50 in.-lbs of energy. The strain rate at the base of the notch was estimated to be approximately 100 sec-1 at the instant of impact. The specimens were heated in situ to the desired impact temperature. The microstructures produced by the various anneals were studied by both X-ray diffraction and metallographic techniques. Fig. 1 reproduces the microstructures observed metallographically following a 10-sec electroetch in a 10 pct KOH solution. Fig. l(a) shows the elongated fibrous grain structure of the as-received material. Following the anneal at 1300" or 1400°C the grain structure was still elongated as shown in Fig. l(b) but the etch pits delineated dense polygonized dislocation arrays within many of the grains. Occasionally a relatively dislocation-free recrystallized grain was found growing into the matrix. The anneals at 1600° and 2000°C resulted in complete recrystallization and some grain growth. The grains produced at 1600°C were still slightly elongated as shown in Fig. l(c) whereas the anneal at 2000°C produced equiaxed grains. The changes in grain size produced the expected changes in the X-ray back-reflection patterns; there was no indication either in the as-received material or the annealed material of any preferred orientation. RESULTS a) Impact Behavior. Fig. 2 reproduces the ductile-brittle transition curves measured in the manner described in the previous section. It can be seen that under these testing conditions the as-received

Jan 1, 1964

By M. Gensamer, B. Lustman

A recent paper described, by means of stereographic pole figures, the preferred orientations produced by cold-rolling low-carbon steel of automobile-body grade. It was found that the surface of the sheet exhibited a deformation texture significantly different from the texture possessed by the inside of the sheet. Efforts to produce the surface texture by buffing a sample exhibiting the normal or inside texture, using a copper lap, have not been successful. In view of the data collected by Kurdjumow and Sachs2, it was suggested that the surface texture might be the result of partial recrystallization of the normal or inside texture. The recrystallization texture of cold-rolled mild steel was studied by Goss3, but he did not use the pole-figure method, so that his conclusions were in need of verification. For these reasons the work reported in here was undertaken. It had two objectives: (1) to study the general behavior of cold-rolled mild steel on recrystallization below the critical temperature Al, and (2) to attempt experimentally a demonstaration of the genesis suggested above for the surface texture in cold-rolled steel. The material was that used by Gensamer and Mehl, cold-rolled to 97.5 per cent reduction in thickness. Fig. 1 is an X-ray pinhole photo-gram of this material, taken with the beam transmitted perpendicular to the plane of the sheet, using a molybdenum target at 35 kv. with no filter. It is typical of the inside texture, but in it the deformation texture is better developed than in the samples that showed a well developed difference between the inside and surface samples. Specimens from this sheet, which was 0.005 in. thick, were annealed for 5 min. at various temperatures in a lead bath. After about 0.0005 in. had been etched from both surfaces, X-ray photograms were prepared, using the technique described in the earlier paper1. Figs. 2 to 6 are photograms of the annealed sheet, at 566, 571, 577, 580 and 650" C. (1050' to 1202" F.), in order. Fig. 2 shows that 5 min.

Jan 1, 1937

By D. K. Crampton

THE study of copper alloys of the age-hardening type has received considerable attention, and, among the alloys which the authors have considered, those containing small amounts of nickel and phosphorus as essential constituents seem especially interesting. Such alloys have attractively great capacity for being hardened and also have relatively high electrical and thermal conductivity in the hardened state. In addition, it has been found that the increase in hardness and strength imparted by aging can be greatly augmented by cold-working, so that axcellent combinations of conductivity and strength are obtainable. In view of the possible importance of the alloys, it was considered desirable to investigate the solubility relationships in the copper-rich portion of the copper-nickel-phosphorus system. This paper presents some of the results obtained in this investigation to date and also gives properties of typical alloys that appear to be of commercial interest.

Jan 1, 1940

By P. Greenfield, C. C. Smith, A. M. Taylor

The Mg-Zr alloy ZA and Mg-Mn alloy AM503(S) are shown to have a markedly improved resistance to creep deformation after suitable heat treatments. This improvement makes them suitable for certain stress-bearing fuel element components in nuclear reactors. The extent of strengthening is described and an explanation of the behavior of both materials is given, based on a combination of strain-aging and grain growth. The increase in operating temperatures of fuel element components in Calder Hall type nuclear reactors has necessitated the development of magnesium base alloys with a very high resistance to creep at temperatures up to 500°C. Such alloys are not required for fuel element cans, which require high-creep ductility rather than strength, but for can supporting and stabilizing components, which are needed to support the imposed loads without deforming more than about 1 pct in times of up to 40,000 hr. The amount and type of alloying addition made to magnesium for these parts is limited by the necessity of keeping the cross-section to thermal neutrons as low as possible. The alloys must also possess a high resistance to oxidation in CO2. Alloys which have been developed for this application include ZA, an alloy of magnesium with 0.5 to 0.7 pct Zr and AM503(S), an alloy of magnesium with 0.5 to 0.75 pct Mn. In the as-extruded condition these alloys are very weak and ductile in creep but it has been found that they can be strengthened to a significant extent by heat treatment. This paper describes the method of developing a high-creep resistance in ZA and AM503(S), the extent of the strengthening produced and discusses the probable mechanisms of strengthening. TEST MATERIALS Specimens were taken from typical casts of ZA and AM503(S) alloys extruded into 2 1/4-in.-diam bars, supplied by Magnesium Elektron Ltd. Typical analyses of the bars were as follows: The as-extruded mean grain diameter was 0.001 to 0.002 in. for the ZA alloy and 0.003 in. for the AM503(S) alloy. EXPERIMENTAL METHODS Extruded bars of ZA alloy, 2 1/4 in. in diameter and 9 in. long, were heat treated in electrical resistance furnaces in an atmosphere of flowing CO2 containing 50 to 300 ppm water, thereby reducing the extent of oxidation compared with that which would have occurred in air. Heat treatments were carried out at 600oc for times of 8, 24, 48, 72, and 96 hr and material was subsequently both furnace cooled and water quenched. In order to measure the effect of time of heat treatment, specimens were creep tested at 400°C and 336 psi for about 1000 hr. Subsequently, the behavior of material heat treated for 96 hr at 600°C and furnace cooled was tested at a variety of stresses from 200° to 500°C. Tests were also conducted at 200o and 400°C on material in the as-extruded condition for comparative purposes. With the AM503(S) alloy, only the effect of heat treatment at 565°C for 4 hr was examined. It has been shown1 that such a heat treatment produces marked strengthening in this alloy. Tests on this material were conducted at a variety of stresses at 200°, 300°, and 400oc with comparative tests on as-extruded material at 200o and 400°C. The creep tests were carried out on machines using dead-weight loading and direct micrometer strain measurements on specimens 5 in. long and 0.357 in. diameter. At temperatures of 400° C and below, the creep tests were conducted in air, but at higher temperatures an atmosphere of CO2 was used. Grain size measurements were made on ZA in the extruded and heat treated states and on each specimen after creep testing. This was done by a line count of a minimum of 20 grains in two or three random fields in the longitudinal and transverse directions. The same method was used for measuring the grain size of as-extruded AM503(S), but the grain size of the heat treated material was so large that this method could not be employed. For heat-treated AM503(S) the large grained characteristics (between 0.1 and 1 in.) were confirmed by the measurement of individual grains. In the case of the ZA alloy, specimens taken from various stages in the program were analysed for hydrogen by a combustion method. Material in various states was also analysed for the soluble and insoluble zirconium content by dissolving in dilute hydrochloric acid. This technique has been useda for the determination of amounts of zirconium present

Jan 1, 1962

By R. Schempp

DURING the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these char-acteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and empha-sized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent cart on. The discrepancies encountered in the determination and classification of the austenitic grain size led to in investigation of some of the variants influencing the austenitic grain size as determined by standard methods.

Jan 1, 1937

By W. E. Remmers

The fact that gray iron increases in volume, cracks and distorts upon repeated heating and cooling is rather conlmon knowledge. In ingot molds, Diesel engine pistons, carburizing boxes, continuous furnace parts, grate bars, stoker parts, and all castings that are subjected repeatedly to high and low temperatures, the phenomenon of growth presents a vital problem. Ingot molds distort and produce cracks which result in seams or laps and later appear as defects in the finished product. The heads of Diesel pistons frequently fail by cracking in a stellar shape. This is attributed usually to the result of permanent growth. Distortion and change of dimension of furnace parts frequently renders them entirely unusable. In chain grate stokers, mechanical difficulties frequently are caused by the growth of the links. In proper operation these links should never attain a temperature sufficiently high to start growth; nevertheless, some have grown in. on an 8-in. length when improperly operated. Even though the phenomenon is generally known there still exists a deficiency in the explanation of the mechanism of this growth. The field of investigators of this subject has a decided variation in opinion concerning the causes. The problem is of sufficient importance therefore to warrant further consideration. Review of Published Work Since the published work, particularly the European, contains much detail, only the outstanding results and conclusions of the investigators will be reviewed. The pioneering investigations of Outerbridge in 1904 and 1905 brought forth the conclusion that growth was not a function of chemical or crystallographic changes but was a result of the formation of fine hair cracks. These cracks are supposedly due to a nonuniformity of thermal expansion and contraction which ruptures the structure of the material. More recently Benedicks and Lofquist presented a purely mechanical theory, which is similar to that of Outerbridge. These investigators believe the temperature gradient from the outside to the center of the cast piece causes a contraction of the outer layers on passing

Jan 1, 1931

By John R. Don

In the South Island of New Zealand an unusually favorable opportunity is offered for the analysis of the older crystalline rocks, underlying the sedimentary rocks which form the "country" of the gold-deposits. The Manipori formation of this island, comprising the greater part of the mountainous district west of lakes Manipori and Te Anau, in Otago, consists of an enormous thickness (estimated by Professor Hutton1 at 160,000 ft.) of crystalline schists, gneiss, syenite, and syenitic gneiss, with associated masses of granite; the whole forming the most picturesque fart of New Zealand. The famous West Coast sounds occur in this formation. No paying auriferous lodes have been discovered in it; and for this reason an examination of the rocks is specially interesting here. Stelzner, Posepny, and others, who have criticised the conclusions of Sandberger, have laid great stress on the fact that all the silicates analyzed by him were taken from the vicinity of orebodies containing those heavy metals which he notes as occurring in the silicates of the country-rock; their contention being that these metals, supposed to occur as silicates in gneiss and other crystalline rocks, were really contained as sulphides, and were therefore impregnations from the neighboring orebodies. The same objection, whatever be its weight, might be urged with equal justice against Mr. Becker's derivation of the mercury and gold of the lodes of the Pacific Coast from' the granite underlying their country-rock. In the case of the

Jan 1, 1913

By W. M. Myers

THE hydraulic properties exhibited by the calcination products of certain limestones were recognized at an early datemore than 2000 years ago. It was known that calcined limestone with the addition of other minerals would react with water and produce an insoluble and stable product. This material could be cast in desired forms or could be used as a cement for the unification of other materials in large masses or for bonding brick or masonry structures. Cements are essentially mineral glues and it is their ability to unify other materials plus their fluidity when first mixed with water, enabling the mass to assume any desired shape, that has made them so extraordinarily useful to modern industry. Like other glues, cements do not exhibit their maximum strength when used alone and only when mixed with proper aggregates do their optimum properties appear. The resulting concrete, a mixture of cement, mineral aggregates and frequently of reinforcing steel, exhibits the most desirable properties of the individual constituents with regard to tensile strength, stability and permanence. The speed with which such mixtures can be -prepared and installed in place with mechanical equipment has facilitated their adoption by the engineering profession concerned with the construction industries. The development and application of improved methods of manufacture have resulted in such economies that the finished product can be sold at a remarkably low price. In addition, the necessary raw materials are of such common occurrence and wide geographic distribution that the manufacture of cement was established in 34 of the 48 states by 1946. Plants under construction will add to this number. In recent years the industry has been characterized by the development of a number of new cements designed to possess special properties essential for use in unusual environments. These have introduced the use of some new raw materials and also have complicated the processes of manufacture. In the following pages, the major varieties of cement of commercial importance are treated in the chronological order of their appearance on the market.

Jan 1, 1949

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air-pollution control is included. However, there are clear indications that the natural gas supply from the conliguous 48 states and continental shelves will not keep up with this rapid growth in demand indefinitely. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale -by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current mine-mouth prices - 60-70 million tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase in gas demand. Although annual discoveries (gross additions to proved reserves) of natural gas in the United States are still on a general upward trend from the current level of 22 trillion cu ft annually, most forecasters do not expect this to increase substantially in the foreseeable future. For example, the updated (to include 1966 and 1967 data) mathematical model of natural gas discovery and production in the U.S. developed by the Institute of Gas Technology (IGT)' projects that discoveries will level out at about 25 trillion cu ft annually in the late 1970's and during the 1980's and then decline to about 21 trillion cu ft by the year 2000 (Fig. 1). This adds up to a new supply for the period 1968-2000 of about 790 trillion cu ft. Experts who usually reflect the producers' viewpoint, such as Radford L. Schantz of Foster Associates,* are relatively more pessimistic. In contrast, a forecast just made by the U.S. Dept. of the Interior is much more optimistic.3 It assumes an increase in gas discoveries of 2.2% per year over the period 1965-80, reaching about 30 trillion cu ft in 1980. If this rate of increase were extended to the year 2000, annual discoveries would reach 46 trillion cu ft at that time, for a total over the period 1968-2000 of about 1100 trillion cu ft. To these forecasts of new gas discoveries must be added proved reserves of roughly 290 trillion cu ft,4 bringing total U.S. supplies for the rest of the century to nearly 1100 trillion cu ft (IGT) and possibly as high as 1400 trillion cu ft (U.S. Dept. of the Interior). This is approximately the same range as that of two estimates of total remaining recoverable natural gas supply: Potential Gas Committee, 980 trillion cu ft5 and IGT, 1450 trillion cu ft.6 Only the 1965 estimate by the U.S. Geological Survey7 suggests that economically recoverable natural gas supplies will not be exhausted around the end of the century. These forecasts are, naturally, based on the assumption that changes in technological, economic, and regulatory environment as they affect the gas industry will be of an evolutionary, not revolutionary, nature. The various forecasts of potential natural gas supply must now be compared to forecasts of natural gas demand (Table I). The general consensus is that the recent Future Requirements Committee projection to 1990' (extended to the year 2000 by the most recent U.S. Bureau of Mines (USBM) projection9) represents the minimum gas requirements (Table 11). They add up to a total of 1030 trillion cu ft for the period 1968-2000. Even this minimum anticipated gas demand exceeds the total remaining supply estimate by the Potential Gas Committee and would nearly exhaust the proved reserves plus new discoveries projected by IGT. The supply situation would appear much tighter if the demand projections of the Texas Eastern Transmission Gorp.10 and the American Gas Assn.(A.GA.)'' were used (Table I). Yet, these higher forecasts probably do not include the effects of such new markets as gas fuel cells, use of liquefied natural gas as a transport fuel, etc. They also may not fully reflect the impact of air quality control on the fuel market. Obviously, the probable discrepancy between projected supply and demand can only be accommodated in four ways. 1) Rapid increase in exploration and drilling activity to provide new supplies in the amount projected by the optimistic U.S. Dept. of the Interior forecast, coupled with an increase in net pipeline imports from Canada and Mexico from the present 0.5 trillion cu ft per year

Jan 1, 1970

By R. T. DeHoff

In any structural transfortnation which is driven by surface tension, the geometric variable of fimdamental importance is the local value of the mean surface curvatuve. Acting through the suvface free energy, this quantity determines the magtnitude of both the pressure and the chemical potential that develops in the neighborhood of an arbitrarily curved surface. A metallographic method which would permit the quaniitatiue estinzation of this propevty is of fundarnerztal irztevest to studies of such processes. In the present paper, it is shoun that the average value of the mean surface curvature in a structuve can be estimated from two simple counting measuretnents made upon a vepresentative metallograpIzic section. No simplifyirlg geonzetric assurmptions are necessary to this deviuation. It is further shoum that the result may be applied to parts of interfaces, e.g., interparticle welds in sintering, or the edge of growing platelets in a phase transformation, without loss of validity. In virtually every metallurgical process in which an interface is important, the local value of the mean surface curvature is the key structural property. This is true because the mean curvature determines the chemical potential of material adjacent to the surface, as well as the state of stress of that material. The theoretical description of such broadly different processes as sintering,1,2 grain growth,3 particle redistrib~tion4,5 and growth of Widmanstatten platelets8 all have as a central geometric variable the "local value of the mean surface curvature". The tools of quantitative metallography currently available permit the statistically precise estimation of the total or extensive geometric properties of a structure: the volume fraction of any distinguishable part:-' the total extent of any observable interface,10,11 and the total length of some three-dimensional lineal feature:' and, if some simplifying assumptions about particle shape are allowed, the total number of particles.'2"3 The size of particles in a structure, specified by a distribution or a mean value, can only be estimated if the particles are all the same shape, and if this shape is relatively simple.14-16 The relationships involved in converting measurements made upon a metallographic section to properties of the three dimensional structure of which the section is a sample are now well-established, and their utility amply demonstrated. In the present paper, another fundamental relationship is added to the tools of quantitative metallography. This relationship is fundamental in the sense that its validity depends only upon the observation of an appropriately representative sample of the structure, and not upon the geometric nature of the structure itself. It involves a new sampling procedure, devised by Rhines, called the "area tangent count". It will first be shown that the "area tangent count" is simply related to the average value of the curvature of particle outline in the two-dimensional section upon which the count is performed. The average curvature of such a section will then be shown to be proportional to the average value of the Mean surface curVature of the structure of which the section is a sample. The final result of the development is thus a relationship which permits the evaluation of the average value of the mean surface curvature from relatively simple counting measurements made upon a representative metallographic section. The result is quite independent of the geometric or even topological nature of the interface being studied. QUANTITATNE EVALUATION OF AVERAGE CURVATURE IN TWO DIMENSIONS The Area Tangent Count. Consider a two-dimen-sional structure composed of two different kinds of distinguishable areas (phases), Fig. l(a). If the system is composed of more than two "phases", it is possible to focus attention upon one phase, and consider the remaining structure as the other phase. The reference phase is separated from the rest of the structure by a set of linear boundaries, of arbitrary shapes and sizes. These boundaries may be totally smooth and continuous, or piecewise smooth and continuous. An element of such a boundary, dA, is shown in Fig. l(b). One may define the "angle subtended" by this arbitrarily curved element of arc, dO, as the angle between the normals erected at its ends, Fig. l(c). Now consider the following experiment. Let a line be swept across this two-dimensional structure, and let the number of tangents that this line forms with elements of arc in the structure be counted. This procedure constitutes the Rhines Area Tangent Count. Suppose that this experiment were repeated a large number of times, with the direction of traverse of the sweeping lines distributed uniformly over the semicircle of orientation.' Those test lines which ap- proach from orientations which lie in the range O to O + dO form a tangent with dA; those outside this range do not, see Fig. l(c). Since the lines are presumed to be uniformly distributed in direction of traverse, the fraction of test lines which form a tangent with dA is the fraction of the circumference of a semicircle which is contained in the orientation range, dO; i.e., vdO/nr or dB/n. If the number of test lines is N, the number forming tangents with dA is N(d0/n). Since each test line sweeps the entire area of the sample, the total area traversed by all N test lines is NL2. The number of tangents formed with dA, per unit area of structure sampled, is therefore

Jan 1, 1968

By A. W. H. Morris, E. A. Steigerwald

The jatzgue beizazriov oj Mietal matrix co))zpos~tes in tension -lensiom loading has been imestigated as a junction of Dolume fraclion veinfovcelnent using the model systems of a silver matrix reinforced with contlnuous or dzscontztinuous aligned tungsten jilamenls and continuous aligned steel filamenls. Appreciable impvocetnents in fatigue strength were obseved in all syslems inzvesLigated, the degree of sl renglhenng-increasing with increasing volume fraclion of reinforcement. The mode of fatigue failure was found to be a function of colutrre jp-actiotz and was also noted to be controlled by the relative fatigue and strength characlerislics of the matrix and reinforcemenl. THE advantages to be gained by suitably incorporating high-strength filaments or whiskers into metallic matrices are well-recognized.' To date emphasis has been placed on the experimental determination of tensile strengths and elastic moduli of metal matrix composites measured parallel to unidirectionally aligned filaments. Several attempts have been made to relate experimentally measured tensile properties to theoretical values calculated from the properties of the components on the basis of the relatively simple "rule of mixtures" analysis. However, relatively few data have been reported in the literature on the fatigue behavior and mechanism of fatigue failure of metal matrix composites. In a study of fatigue crack propagation in aluminum plus steel wires and aluminum plus tungsten wires, Forsyth et a1.2 found that the incorporation of small numbers of filaments suitably dispersed were capable of substantially reducing the rate of fatigue crack propagation. For this purpose, the strength of the filaments appeared to be more important than the aspect ratio and the authors reported that parallel filaments were not the most favorable orientation for increased strength. In a basic study of the fiber reinforcement of metals, Williams and 0'brien3 report preliminary results which indicate a considerable improvement in fatigue strength in reversed bending fatigue of a steel wire-reinforced aluminum alloy composite. In a study of the influence of interfacial bonding on fatigue behavior, Baker4 has also reported improved fatigue properties in stainless steel-reinforced aluminum composites. In contrast, Ham and place5 report that, although tensile properties are improved greatly by filament reinforcement, the reinforcement of copper with continuous, brittle tungsten wires up to 23 vol pct was comparatively ineffective against fatigue. The authors attribute the poor fatigue properties of the composite to fatigue hardening of the matrix at the tips of cracks which can build up stress concentrations sufficiently large to fracture proximate filaments. Baker and cratchley6 failed to find marked improvements in the reversed-bending fatigue properties of silica-reinforced aluminum. The study was complicated by the complex behavior in a composite during the compres-sive half-cycles imposed in this type of loading. This was manifested in the failure of the composites by de-lamination, a contributing factor being the presence of aluminum oxide at the matrix-filament interface. Prior to the general acceptance of filament-rein-

Jan 1, 1968