Search Documents

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators1,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945

By Sherwin F. Kelly

MANY baffling problems of crustal geology-of warping and folding, elevation, subsidence, and great dislocations of the earth's surface-may now be on the verge of yielding to the science of geophysics. Electric, magnetic, gravitational, geothermal, and seismic methods are being turned to the gathering of geological evidence buried by deep layers of rock, or lying beneath the waters of the oceans. In this hope, B. L. Miller expresses the opinion that these geophysical studies will sup- ply useful data bearing-on some of the more theoretical problems of North American geology. Among these for example, is the explanation of how Appalachia disappeared. This ancient land mass is supposed to have foundered beneath the Atlantic Ocean after the close of the Paleozoic era and the question arises, was it warped or faulted downward? The geophysical data, though meagre, indicate that the surface of the dense, basal rocks, the probable remnant of ancient Appalachia now underlying the Continental Shelf, slopes downwards to a depth of some two miles below sea level at a distance of 140 mi. from shore: thus suggesting that the subsidence was the result of warping downward rather than abrupt faulting.

Jan 1, 1938

By Francis J. Dennis

(San Francisco Meeting, October, 1911.) MANY factors govern the value of dredging-ground, and much capital can be wasted by the mistaken policy of contracting for the purchase of property and the installation of machinery before a thorough, examination has been made. To the uninitiated investor the presence of gold is generally the criterion,, and very superficial evidence is necessary to satisfy him as to this point. He considers the comprehensive report of a competent engineer as a wasteful extravagance and cannot understand why the engineer requires so much time and money to ascertain the information on which to base his conclusions, when the promoter can furnish him such pleasing and satisfactory data with but little expenditure of time and money. The uninitiated investor will often optimistically risk capital for purchase and equipment, and not until the venture comes to grief does he learn that the conditions are wholly unsuited for dredging. In many instances, a short preliminary examination by a competent engineer would have disclosed these facts. The mere presence of gold is by no means sufficient; some of the other factors necessary to be ascertained in determining the value of placer-ground for dredging-purposes are : (1) character and distribution of gold, and how much can economically be recovered; (2) character of bedding underlying the gravel, its contour, and whether its gold can be recovered by ordinary dredging-operations; (3) area and depths of gravel, surface contour, over-burden, water-level, proportion of fine material and boulders, and the presence of any material which might interfere with the dredging-operations and the recovery of the gold; (4) water-supply, power available, labor, transportation, and supplies, and cost of these ; (5) climatic condi-tions; (6) title to property, cost and royalties, and legal obstacles to carrying on dredging-operations. A brief reconnaissance may be sufficient to determine that some of the essential conditions for successful dredging are

Apr 1, 1912

By J. Parke Channing

ALTHOUGH the original thought of investigating waste in industry came from a mining engineer, Herbert Hoover, and although the chairman of that committee was a mining engineer (although the real work was done by the vice-chairman, L. W. Wallace), it is an interesting commentary that when the report first saw light, at St. Louis, on the first of June, 1921, some people most violently went up in the air when it was submitted by the representatives of the mining engineers. At the time they resented most markedly the report of the committee that 50 per cent. of the waste in industry, or as Mr. Ingalls in his paper has properly said, inefficiency in industry, was to be laid upon management. The reason for that seems to have been that, as a whole, the mining industry is pretty well organized and is superior to a large number of manufacturing industries including those studied by the Report. However, this very meeting shows that even the min-ing engineers have finally realized that there is waste or inefficiency in mining and that a large proportion of it can, with propriety, be assessed against management.

Jan 3, 1922

By Harrison Souder

MAGNETITE mining and milling in the Eastern States showed continuing improvement during the year. Some of the smaller mines remained idle, but the larger operations responded promptly to the improved situation in the iron and steel industry. The output of ore for 1936 was over twice that for 1935. A number of improvements were made in mine plant and equipment, and operating forces were increased and maintained at near normal. The coming year should see additional mines started up and production increased at the larger properties.

Jan 1, 1937

By T. M. Girdler

INDUSTRIAL progress and development in this country from the earliest daps to the present has proceeded at an ever-quickening pace. Yet during recent decades the nature of our industrial progress and development has undergone a change of great significance. The earlier days were a period of tremendous expansion. Population was increasing by leaps and bounds. Vast areas of new land were being .2 opened to settlement. And almost boundless new sources of timber, coal, oil, ores, and power were being opened to ever-expanding markets. Today, however, that picture has al- most completely changed. Today, with population increase tapered way off and the opportunity for free expansion into western frontiers gone, the great industrial development of our country continues on a vastly different front. Industrial progress and development today rest on a foundation of technology. The key- stone is research. Our frontiers to- day are frontiers of sciencec

Jan 1, 1939

By Lawrence K. Jetter, Robert F. Mehl

SOME advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory.? Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selected for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatometric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system-a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation ;2,3,4 there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type-the ideal case which Becker5 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1942

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ALLEN, Roy H., Capt., Air Service, Bureau of Aircraft Production, Washington, D. C. *AMIDON, CLAUDE E., Chemical Warfare Section', Astoria, L. I. *ARCHBALD, HUGH, 311th Infantry, 78th Division, American E. F. ASKIN, THOMAS B. H., Radio Station, Cavite, P. I. *AYER, FRANK A., Lieut., Commanding Officer, -270th Aero Squadron, American E. F. BARBA, W. P., Lieut. Colonel, Ordnance, U. S. A., Washington, D. C. *BARRETT, LESLIE P., 1st Lieut., 5th Field Artillery, American E. F. BLICKENSDERFER, F. C., 1st Lieut., N. A., Ordnance Dept., Edgewood Arsenal, Edgewood, Md. *BROOKS, FLOYD R.., Lieut., Canadian Engineers, Seaford, England. BROWN, GEORGE M., Co. G, 1st Replacement Regiment, Washington Barracks, D. C. *BRUNEL, LOUIS J., Lieut., 5th Field Artillery, Brigade Headquarters, American E. F. *BRUNTON, D. W., Cons. Engr., Naval Consulting Board, Washington, D. C.

Jan 11, 1918

By C. Q. Payne

(New York Meeting, February, 1912.) THE art of crushing ores and other materials by means of rolls is a comparatively recent one. While the first record of rolls using iron crushing-surfaces dates back to the year 1806, when they were employed in Cornwall, their principal development has taken place during the last 30 years. To Stephen R. Krom belongs the credit of the pioneer in introducing the belted high-speed roll, which has had its origin and a marked development in this country. His notable contribution to the art was in the use of a single bed-plate or frame supporting the roll-shafts, and to which levers holding the movable roll-bearings were pivoted. He also made use of steel tension-rods to support the crushing-strains, and of hammered-steel tires for the crushing-surfaces. These changes brought the design of crushing-rolls to a high level. Following closely thereon, about 1885, W. R. Eckart conceived the idea of the swivel or ball-and-socket support for the roll-shaft bearings. This is an excellent mechanical conception, especially for bearings held against a spring pressure, and while it may not be necessary for all types of rolls, yet it has been quite generally adopted by other roll-designers, and illustrates the refinement which roll-construction has now reached. Other engineers, as for example, Argall, Vezin, Roger, and Sturtevant, to mention only a few among many, have also given the closest attention to the various details of rolls, such as the frame, springs, bearings, and shafts, and have developed many novel and original designs. It has remained, however, for the boldness and originality of Mr. Edison to extend the field of crushing-rolls in two new directions, and to cause them to exercise new functions. In developing crushing-machinery for his Portland cement works, Mr. Edison constructed ? giant " rolls, having a diameter of 6 ft. and a length of. face of 7 ft.

Jun 1, 1912

By Edmund C. Pechin

THE writer approaches this subject with a great deal of diffidence —first, because it is utterly impossible to treat it satisfactorily within the limits of a paper, and, secondly, because the larger development is of so comparatively a recent date as to make authoritative data on some interesting points unavailable. For over one hundred years small charcoal-fnrnaces have been in existence, at widely scattered points, making a few tons of iron daily, and then gradually increasing to a daily output of, say 10 to 12 tons, as the market widened. With the exhaustion of local supplies of wood, inaccessibility to market, and sharp competition, bringing lower prices, many were compelled from time to time to make temporary stops, and finally to cease altogether. During the first half of the century there were at different times in operation between 75 and 90 charcoal furnaces. The last Directory of the Iron and Steel Works of the United States (1890) gives 19 as the number of charcoal-stacks in Virginia. Of these several are cold, and, it is

Jan 1, 1891

By R. P. Abendroth

The hydrogen-water vapor ratio at which Fe-Cr alloy, chromium oxide, andiron chromite coexist in equilibrium was determined between 900" and 1200°C. A thermogravimetric method was used to determine equilibrium conditions. The results fit a straight-line relationship in the temperature region studied, and are given by Reduction experiments were also performed to confirm the results of the equilibrium investigation. ThE oxygen pressures at which Fe-Cr alloy, chromium oxide, and iron chromite coexist in equilibrium have been previously determined by Boericke and angert,' Morozov and Novokharski,' and Katsura and uan. Only one determination (at 1300°C) was made by Katsura and Muan, but it agrees with the results of orozov and Novokharski. The results of Boericke and Bangert, however, differ appreciably from the results of these investigators. Previous studies have assumed that the equilibrium metallic phase is pure iron, but Dahl and Van vlack have shown that the iron contains from about 1 wt pct Cr at 1000°C to over 2 wt pct above 1300°C. The chromium oxide also contains a small amount of iron in solid solution. In the present study, hydrogen-water vapor mixtures were equilibrated with the condensed phases, using a therrnogravimetric method to determine equilibrium conditions. The reaction can be written EXPERIMENTAL General Procedure. The starting material was a sintered pellet of Fe2O3-Cr2O3 solid solution with a hole in the center, and was placed on a fused silica hook. This assembly was raised into the preheated hot zone of the furnace in a helium atmosphere, hooked onto a fused silica hangdown suspended from one arm of an Ainsworth Model RV-AU-1 recording balance, and the starting weight determined. A flowing hydrogen-water vapor atmosphere was then exchanged for the helium by evacuation, and the sample reduced until the weight loss indicated the sample composition to be in the alloy-Cr2O3-chromite field. The tem- perature was adjusted incrementally until constant sample weight was achieved for several hours, to within 0.02 mg. A hydrogen-water vapor atmosphere of different composition was then admitted, and the same procedure carried out. At the end of a series of determinations, the sample was examined by X-ray diffraction to verify the presence of the desired phases. Microscopic examination of the silica hook showed no interaction with the sample, nor did it lose any weight. Several criteria were used to insure equilibrium besides constancy of weight. For a given hydrogen-water vapor composition, equilibrium was approached from both oxidizing and reducing sides by varying the furnace temperature slightly. The resulting slow weight loss or gain was observed for several hours. Constant weight could be re-established by returning to the original furnace temperature. The last criterion used was varying the relative amounts of the phases by further reduction or oxidation, and observing any changes in temperature required for constant weight for a given hydrogen-water vapor atmosphere. None were observed. This procedure was essentially the same as approaching the equilibrium from oxidizing and reducing sides, but larger weight excursions were carried out. Sample Preparation. Reagent-grade Fe2O3 and Cr83 powders were mixed in the desired proportions and heated in air at 1250°C for 2 hr. The mixture was re-ground and heated in air overnight at 1250°C. X-ray diffraction showed complete solid-solution formation as a result of this procedure. The solid solution was then pressed into l/2-in.-diam pellets using Carbowax 4000 as a binder. The hole was drilled in the center, and the pellets were sintered 24 hr at 1250°C in air on a bed of Fe2O3-Cr2O3 of the same composition, contained in an alundum boat. After cooling, the pellet surfaces were abraded with 310 paper to remove any surface compositional differences, such as loss of Cr2O3. Chemical analysis of the sintered pellets was 67.16 wt pct CrP3 and 33.02 wt pct Fe203. Atmosphere Generation and Control. The hydrogen-water vapor atmospheres were generated by passing Matheson ultrahigh-purity hydrogen, with no further purification, through two water bubblers contained in a constant-temperature water bath. Since the water-vapor dew points required in this study were below room temperature, the bath was insulated, and was cooled by thermoelectric-immersion devices. The bath temperature was controlled to 0.0l0C. Since rather high flow rates of about 900 ml per min were used through the furnace tube, an independent check of the dew point was made to insure saturation of the hydrogen by the water vapor. Although the dew point could only be determined to within 1/2"C, the determined dew points agreed with the water-bath temper-

Jan 1, 1967

By E. H. Jr. Dix

THE consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathews1 and by Tammann.2 Campbell and Mathews described principally the beginning of solidification. They found the curve of beginning of solidification to rise gradually from the melting point of pure aluminum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AlSb. The curve then drops to the melting point of pure antimony. Tammann explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AlSb. The space lattice of the compound AlSb, according to Owen and Preston,3 is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony.

Jan 1, 1930

By J. J. Carrigan

DURING the experimental stage in our use of the electric cap lamp in the Anaconda mines at Butte. Mont., we were somewhat concerned as to how the spitting of fuses would be carried out if we completely eliminated the open-flame light. This problem was at once given serious attention by the engineering research department and some thought was given to having all blasting done by the use of electric delays, which has been the practice for some years

Jan 1, 1936

By Alan Kissock

MOLYBDENUM is thought of as one of the rarer elements, for though it occurs in almost every country of the world it is seldom found in commercial quantities. In this country, however, there is one deposit which makes the term "rare" a misnomer. There are two commercially mined molybdenum minerals: molybdenite, the sulfide, and wulfenite, a lead molybdate. Of these two only the former is of any con- sequence but wulfenite is of mineralogical interest. It is frequently associated with oxidized lead ores and particularly in arid sections. Deposits, however, are usually quite superficial. It is highly oxidized and yet it does not appear to be an alteration product for it apparently disappears below water level and I know of no case where primary molybdenite, or in fact any molybdenum whatever has been identified below these surface wulfenite occurrences. The genesis of wulfenite would make an !- interesting study.

Jan 1, 1933

By D. R. Mitchell

FOR the second consecutive year, attendance at the Coal Division sessions far exceeded exoectations. Those in charge were continually faced with problems of finding seats and space for attending members. 115 seats were set - II~ for the annual luncheon meeting of the Division and approximately 175 members showed un. Since the hotel management would not serve more than the 115 it meant that 60 members were forced to eat elsewhere. This created hard feelings with some members. How- ever, officials of the Division were not able to obtain in advance any indication of this overflow crowd, but are suggesting to the New York Office that some means other than ticket sales be adopted to obtain an estimate of Division luncheon and dinner attendance. Members could be circularized prior to he meeting or they could be checked when registering as to the events they expect to attend. Under the inspiring leadership of Cadwallader Evans, Jr., Chairman, the Coal Division had a phenomenal growth during the year. Reporting at the luncheon meeting, Newel1 Alford stated that approximately 190 new members had been obtained. A few more years of continuing increase at this rate will make the Coal Division one of the largest Divisions in the Institute.

Jan 1, 1944

By K. P. Gupta, P. C. Panigrahy

The stabilization of the R, a-Mn, and 0-Mn phases have been studied in the Mn-Ti-Fe and Mn-Ti-Co systems. Iron and cobalt both appear to stabilize the (Mn-Ti) R phase to almost the sarne extent. The R-phase region was found to extend from the lowest e/a to slightly beyond the maximunz e/a limit known for this phase. But, while iron appears to stabilize the a-Mn phase, cobalt tends to stabilize the p-Mn phase. In the two systems manganese appears to get replaced by iron and cobalt in each of the mentioned phases. The instability of the a-Mn phase in the Mn-Ti-Co system and the /3 -Mn phase in the Mn-Ti-Fe system cannot be explained on the basis of adverse size effects because atomic diameters for both iron and cobalt (C.N. 12 at. diam) are ziery similnr and not much different from manganese which they replace. Qualitatively, the reason for the stability of the a-Mn and the p-Mn phases can be traced to the more favorable e/a ratio prevailing in the respective systems and to a competing tendency between the two phases. In transition metal alloy systems the o, p,P, R, a- Mn,' and p-Mn2 phases have been claimed as electron compounds. A large volume of work has been done to establish the criterion for the formation of the o phase but until very recently practically no systematic work was done on the a-Mn and the /3-Mn phases. A recent investigation on the P-Mn phase3 indicates the e/a criterion for p-Mn phase stabilization. Since the R phase was first known to appear only in certain ternary systems1 no detailed work was then possible for this phase. The R phase has been recently discovered as a binary intermetallic compound in the Mn-Ti~ and Mn-si~-' binary systems. The existence of binary R phases opens up the possibilities of studying the effect of alloying elements on the stabilization of the R phase. Of the two binary systems possessing an R phase, the Mn-Ti system appears to be more interesting because at a suitable high temperature it is possible to find the three electron compounds, the a-Mn, p-Mn, and R phases, side by side and it is possible to study the effect of a third transition element on these three electron compounds. For the present investigation iron and cobalt, so called B elements for the formation of electron compounds, have been used as the third element to study the stabilization of the a-Mn, P-Mn, and R phases. EXPERIMENTAL PROCEDURE The alloys were prepared by using 99.9 pct pure electrolytic Fe and Mn, 99.5 pct Co, and crystal bar titanium, supplied by Semi Elements Inc., New York and Gallard Schelsinger Mfg. Co., New York. Weighed amounts of the components were melted in recrystal-lized alumina crucibles in an inert atmosphere (argon) high-frequency induction melting unit. Titanium was made into fine chips for easy dissolution and a special charging procedure was adopted to avoid contacts of titanium chips with the alumina crucibles. Up to 20 at. pct Ti, the maximum titanium content in the investigated alloys, there was no visible sign of reaction of titanium with the alumina crucibles. With a careful control of melting time and temperature the losses were minimized and were always found to be below 0.1 pct. Because of such small and almost constant weight losses, the alloys were not finally analyzed. The alloys were wrapped in molybdenum foil and annealed in evacuated and sealed silica capsules at 1000" * 2°C for 72 hr and subsequently quenched in cold tap water. Annealed samples were examined metallographically and by X-ray diffraction. For all high manganese alloys oxalic acid solutions of various concentrations and 1.0 pct HN03 solution were found suitable as etching reagents. Best contrast between the a-Mn and the R phases could be obtained by using freshly prepared 60 pct glycerine + 20 pct HN03 + 20 pct HF solution. For high iron and cobalt containing alloys, especially for alloys containing the a-Fe, y-Fe, and P-Co phases, 15 cc HNOJ + 60 cc HC1 + 15 cc acetic acid + 15 cc water solution was found to be the best etching reagent. All X-ray diffraction work was carried out (using specimens prepared from annealed powders) with a 114.6 mm diam Debye-Scherrer camera using unfiltered FeK radiation at 25 kv and 10 ma. All calculations for X-ray diffraction work were carried out using an IBM 7044 digital computer RESULTS AND DISCUSSION The two ternary systems, MnTiFe and MnTiCo, were investigated near the manganese rich end, Figs. 1 and 2, and show some common features. In both alloy systems large extensions of narrow R phase regions occur at almost constant titanium contents. At titanium contents higher than that of the single phase R-phase alloys, the same unidentified X phase was found in both ternary systems. The extensions of the X phase close to the Mn-Ti binary indicate that this phase could be the TiMns phase. Too few X phase diffraction lines were present in the diffraction patterns to make positive identification of the X phase. In contrast to this similarity the two systems show opposite behavior in the extensions of the a-Mn and 8-Mn phase regions; while iron tends to stabilize the a-Mn phase, cobalt

Jan 1, 1970

By J. A. Hutcheson

NO one questions that it is technically possible to achieve the controlled release of atomic energy in a form that can be converted into heat or electricity. However, before this is actually an accomplished fact a great amount of work must .be done. This work falls into two general classifications: research and engineering development. At present a research program is under way in this country, co-ordinated and directed by the Atomic Energy Commission, which, as time goes on, will uncover fundamental knowledge of this new science that is essential before industrial applications of atomic energy are practical. Undoubtedly therefore, as the store of available knowledge increases, a time will come when answers to the many questions relating to practicality of atomic energy in industry can be determined with reasonable certainty. That the application of atomic energy in industry will eventually be proved practical is assumed. What then are the engineering problems that must be solved before the first practical electric power generating station can be built?

Jan 1, 1948

By James Malcolmson

(New York Meeting, February, 1913.) THE Tigre Mining Co. of Mexico, owned by the Lucky Tiger Combination Gold Mining Co. of Kansas City, decided early in 1910 to enlarge its mill, which consisted of a concentrator milling 3,000 tons of ore per month. The enlarged plant was designed to crush and concentrate 6,000 of ore and to cyanide 7,500 tons per mouth. The extra tonnage cyanided was to be obtained from tailings which were stored below the old mill. Power was supplied to the old mill from four boilers; a 150-h-p.. Corliss engine and two Weber 60-h-p. gas-engines using producer-gas made from charcoal. The total horse-power required, including 60 h-p. used for machine-drills in the mine, was approximately 275. Cord-wood cost $4.32 per cord, 8 by 4 by 3 ft., and charcoal $15 per ton. The fuel supply in the surrounding country was approaching exhaustion; more than 150 mules and 50 men were engaged in cutting and transporting this fuel, and the unsettled political, conditions in Sonora were such that it would be practically impossible to keep an organization of this kind together. The price of fuel was steadily rising and at times it became almost impossible to get sufficient fuel to operate.

Jan 4, 1913

ALABAMA. Aldrich.-Aldrich, W. F. Anniston.-Noble, A. E., 20th St. and Wilmer Ave. Auburn.-Brown, R. L., Box 0. Bessemer.-Abbott, C. E., T. C., I. & R.R. Co. Ferguson, V., U. S. C. I. Pipe & Fdy. Co. Williams, E. P., Tenn. C., I. & R. R. Co. Birmingham.-Aldricb, T. H. Aldrich, T. H., Jr., 406 Woodward Bldg. Allen, A. W., 1616 S. 14th Ave. Bowron, J., 1401 S, 20th St. Burbidge, T. A., Browu-Marx Bldg. Coxe, E. H., Tenn. C., I. & R. R. Co. Crawford, G. G., Tenn. C., 1. & R. R. Co. Crockard, F. H., Woodward Bldg. Dimmick, F. D., Dimmick Pipe Co. Ellis, E. E., 1515 Brown-Marx Bldg. Fairbairn, C. T., Woodward Bldg. Fies, M. H., 2316 Highland Ave. Hiller, E., 516 Brown-Marx Bldg. Hillman, M. P. G., 707 Empire Bldg. Ludwig, C. P., 12th Ave. and 12th St. McCormack, G. B., Lookout Mt. Iron Co. McCrery, C., Tenn. C., I. & R. R. Co. Moffett, C. A , 909 Brown-Marx Bldg. Peters, R.. Jr., Brown-Marx Bldg.

Jan 1, 1917