Search Documents

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansen1 and Haughton,2 the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 257.3°C ± 0.1°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys,4,5 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157.2°C ± 0.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4'C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. THERMAL ANALYSIS Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high flash point was used. A platinum-platinum rhodium thermocouple 0f fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermo-couple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.2°C, and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it seems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16r, in. thick, sufficed to give a cooling rate of from 1° to 2°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

William Clinton Brown, Brooklyn, N. Y.: The demand for an apparatus for cooling water for condensers, refrigeratingmachinery and air-compressors, as well as water-jacketed furnaces, has led manufacturers to put such an apparatus on the market, so that it is now possible to purchase a cooling-tower, properly designed and constructed, by simply stating the amount of water to be cooled and the temperatures of the hot and the cold water. The principle is similar to that described by Mr. Henrich, but wood is not used in the best apparatus. There are two great objections to wood: First, it cannot last long under the very trying conditions to which it is subjected; and second, it absorbs the organic matter with which water in constant use becomes impregnated, and the resulting odor is very disagreeable. A few days ago I saw a cooling-tower and condenser, built by the Henry R. Worthington Co., in operation at the Edison electric-lighting station in Brooklyn, N. Y., cooling the water for a 700 horse-power condenser. It consisted of a large stack of iron, about 15 feet in diameter by about 30 feet high. This stack was filled with tiling through which the water falls. A whirligig distributes the water evenly over the top, and a large fan, about 6 feet in diameter, driven by a 10 horse-power electric motor, blows air into the bottom, thus giving a positive circulation. The water, in running down the sides of the tiling, is met by the blast of air, and enough is evaporated to cool the rest. The vacuum-gauge on the condenser showed 26 inches; so the condenser was undoubtedly getting sufficient cool water.

Jan 1, 1896

By Irwin Roman

IN studying the possibilities of a continuously recording magnetometer for use along the surface of the earth and in an airplane, the Federal Bureau of Mines was led to a study of the theoretical resolving power of magnetic observations, both in the variation of the total magnetic intensity and in each of the two components ordinarily measured. Along with this general study, an attempt was made to determine the relative worth of the total intensity anomaly and the vertical anomaly in geophysical prospecting. General considerations led to three conclusions: I. In the northern magnetic hemisphere of the earth, the total intensity anomaly is offset to the south of the vertical anomaly, for a positive anomaly (see Appendix, note I). 2. The resolving power of magnetic observations decreases rapidly with distance from the disturbing body. 3. The horizontal anomaly has little value in prediction of the disturbing body but might be useful in making a choice between bodies suggested by the vertical or total anomaly. Some of the considerations leading to these conclusions were: I. The normal intensity and the anomalous intensity are vectorially additive; hence for a positive anomaly in the northern magnetic hemisphere the total intensity will be a maximum at some point south of the disturbing body and north of the point at which the line to the disturbing body is parallel to the normal earth's field. The anomaly itself has a maximum value directly above the body. For a positive anomaly of constant magnitude, the total intensity will be a maximum when the anomaly vector is parallel to the normal vector. This is shown schematically in Fig. I (not to scale) for a magnetic distribution not restricted to a relatively thin sheet in the magnetic meridian. The normal field has a magnitude Io with vertical component Vo and horizontal component H,. Six station points along a traverse' across the body from south to north are shown at M to S. At each of these stations the normal magnetic field vector terminates at F. At each of these stations the magnetic field vector due to the disturbing body B terminates at A. The line through the station point and the point A passes through B. The magnitude of the anomaly, indicated by the length of the vector terminating at A, is proportional to some power of the distance from the station point to the disturbing body. If the' disturbing body B is a concentrated point of magnetic material, the anomaly is proportional to the inverse second power of the distance. For a uniform magnetic distribution over a line perpendicular to the observed traverse, the anomaly is proportional to the inverse first power of the distance. For surface distributions, the law of intensity is more complicated. At each field point, the total magnetic intensity T is the vector sum of the

Jan 1, 1946

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

By Robert T. DeGavre

INTRODUCTION The $645 million financing for Inco Ltd's Soroako nickel project in Indonesia not only represents a significant human achievement but also there are certain important lessons that can be derived from Inco's experience in financing the project. The paper will not present a technical assessment of the project since Inco Ltd. submitted a series of papers on this subject at the international Laterite Symposium as part of the 108th Annual Meeting of the AIME in February 1979. BRIEF HISTORY OF THE SOROAKO PROJECT Table 1 summarizes the milestones achieved in the Soroako project and its financing. Exploration Phase A contract of Work was signed on July 27, 1968 by the Republic of Indonesia and F.T. International Nickel Indonesia (P.T. Inco) covering an extensive area of over 25,000 square miles on the two southeastern arms of the island of Sulawesi. The Contract provides that P.T. Inco has the sole responsibility for financing the project and determining the terms on which the financing should be obtained, that P.T. Inco has the right to receive and hold outside of Indonesia foreign exchange revenues and to freely dispose of such revenues, and that Indonesians have the right to purchase up to 20% of the equity of P.T. Inco over a period following start of production. P.T. Inco began field investigations in the Contract Area in August 1968. Preliminary reconnaissance sampling with portable drills broadly outlined areas of favorable laterite terrain which were then systematically sampled on surveyed grids. By early 1971 sufficient exploration work had been completed to indicate that the laterite deposits near Soroako could sustain a major nickel-producing plant (figure 1). Pilot plant studies in 1970 and 1971 at Inco's research station in Port Colborne, Ontario, using two bulk samples of Soroako ore material, also confirmed that the ore could be upgraded and treated for the recovery of its metal values. Feasibility Phase Encouraged by the results of its exploration program and pilot-plant work, Inco Ltd. commissioned Toyo Engineering Company of Japan in August 1971 to prepare a capital cost estimate for a relatively small nickel project called "Stage I". Stage I was to be a single-line pyrometallurqical process plant with an annual capacity of approximately 15,000 metric tons of nickel contained in 75% nickel sulphide matte (see Figure 2). Electric power was to be supplied by a thermal power station. It is important to recognize that Inco's strategy was to develop the Soroako ore deposits in several stages: first, construct a small project to gain experience and to reduce the initial capital outlay and then later expand in one or more steps to a much larger project to achieve maximum economies. The strategy reflected both Inco's financial position in 1971 as its sales and earning dropped sharply and the difficulties previously experienced by Inco in trying to launch in the late 1960's very large "greenfield" nickel projects in New Caledonia and Guatemala. Toyo's Project Development Study was completed. in January 1972. Based upon Toyo's cost estimate for physical facilities, Inco estimated the total capital cost of Stage I to be $115 million. For the next several months, Inco ran numerous in-house financial feasibility studies, using as inputs Toyo's cost estimate and the results of its exploration and pilot plant programs. In September 1972, Inco completed a project feasibility study which was based upon a capital cost estimate of $135 million. The feasibility study was immediately made available to potential partners and lenders. Partner Negotiations The Japanese nickel market had from the outset been central to Inco's planning for the Soroako project. That market had been growing dramatically at rates in excess of 20% per annum during the 1950's and 1960's. Japan had established, for rational security and other reasons, a domestic

Jan 1, 1985

By F. C. Smyers, E. W. Merrick

ALTHOUGH the zinc and pyrite concentrates produced at Midvale go to other companies, the United States Smelting Refining and Mining Company smelts and refines its own lead. Refining is the first step of the process that is done at some distance from the mining operations, the plant being at East Chicago, Ind., an industrial center about 25 miles southeast of Chicago. For years it has been notable as being the only lead refinery in the country using the Betts electrolytic process. The original buildings, many of which are still in use, were erected in 1906 when the plant was known as the United States Metals Refining Co. In 1920 the parent company sold its copper refinery at Chrome, N. J., and since the copper refinery was also known as the U. S.

Jan 1, 1948

By G. Birkbeck, T. C. Wells

Pearlite morphology in three commercially produced, low-carbon steels has been studied using optical and electron microscopy. A reduction in the cooling rate from 600° to 6°C per hr increased the interlamellar spacing but had little effect on pearlite content. The form of the lamellae was also assessed in terms of a new parameter, the ratio of lamellae length to interhmellar spacing. The variation of this parameter with cooling rate depended on steel composition. For each steel, it would appear that an optimum cooling rate exists at which lamellar pearlite can be produced to the greatest extent, though not necessarily the same extent in different steels. PeARLITE morphology depends principally on steel composition, prior austenite grain size, and either cooling rate or isothermal transformation temperature. Alloying with manganese,'" fine grain size,374 and slow cooling rates reduce the likelihood that a well-developed lamellar structure will be produced. Instead, imperfect structures usually consisting of partly globular carbides are formed in a ferrite matrix. Such structures have been described as granular.1,2,5 degenerate,6 or semi4-pearlite. Manganese additions also progressively lower the eutectoid temperature and the carbon concentration at the eutectoid so so that, for a given carbon content. the pearlite fraction is increased as manganese is added. While the effects of manganese are understood in a general way, quantitative studies of pearlite morphology have been carried out mainly on steels of eutectoid composition;9 little quantitative data is available for low-carbon steels. Certain anomalies exist in the behavior of steels containing -1.5 pct Mn, however. The pearlite morphology in niobium-treated steel differs from that which is generally accepted as typical of low-carbon/manganese steels in that a reasonably well developed lamellar structure is sometimes observed. In the present work, the effects of changes in cooling rate from 600° to 6°C per hr on the pearlite morphology in three commercially produced, low-carbon steels have been studied by both optical and electron microscopy. I) MATERIALS The steels were of the following types: 1) 0.1 pct C, 0.4 pct Mn steel (En 2, a composition similar to specification SAE 1010); 2) niobium-treated, 0.2 pct C, 1 1/2 pct Mn steel (BS 968:1962); 3) silicon-killed 0.2 pct C, 1 1/2 pct Mn steel (En 144, a composition similar to SAE 1320). The chemical analysis for each steel is given in Table I. To facilitate the comparison of pearlite morphology in the three steels, steels 1 and 3 (which were obtained as 1/2-in. plate and 1-in.-diam bar, respectively) were hot-rolled in the laboratory to $ in. thickness, finishing at around 850°C. The BS 968:1962 was received as 1/8-in. plate finished at 885°C and was not further worked. Specimens from each steel were heat-treated in vacuo at 950°C for 1 hr and cooled at rates of 600°, 60°, and 6°C per hr. 11) EXPERIMENTAL Pearlite contents were determined by point counting (500 points) on longitudinal sections mechanically polished and etched in 2 pct nital. Pearlite morphology is usually considered in terms of interlamellar spacing. For pearlite colonies randomly distributed in space and having a true, constant interlamellar spacing So Pellissier et al.9 determined the distribution curve for the apparent spacings of the lamellae on a random section plane. The areal fraction fs of the pearlite colonies occupied by apparent spacings up to a limiting value S is given by:

Jan 1, 1969

By Zay Jeffries

A SURVEY of rare metals and minerals for the past year places uranium as one of two partners, the other being the neutron, in what historians will probably say is the greatest discovery in physics at least during the year and probably for a consider- ably longer period. The uranium atom has been made to divide into parts somewhat after the style of reproduction of the amoeba. When an amoeba divides into two parts, however, it produces two amoebae substantially alike and each substantially like the parent: furthermore, there is no considerable change of energy when this happens. When the uranium atom divides it yields other atoms such as barium and krypton with the complete destruction of the original uranium atom but with the liberation of a tremendous amount of energy. This will be discussed more at length later.

Jan 1, 1940

By B. A. Stainton, John D. Gill

OUR combined economic activities have as their goal the maximum of individual well-being and national security. In this age of intense international competition the two objectives are closely related. For many decades, the maximum of well-being and ability to maintain national security have moved generally upward. The best single measure-perhaps the only adequate measure -of the level of the rising goal is the per capita real national income (national income corrected for price changes). For centuries before the industrial revolution the income of the world's population changed little from generation to generation. In our country prior to 1800 the growth of national income was hardly measurable from decade to decade. Since 1850, perhaps since the "industrial revolution," the growth of per capita real income has been increasing geometrically. Of major importance is the accelerative growth of the productive ability of our economy. Inadequate consideration of its implications is partly responsible for periodic delays in solving our princi-

Jan 1, 1946

By W. F. Domis, F. von Gemmingen, F. Garofalo

The effect of rain size on the creep behavior of an austenitic iron-base alloy has been studied at 1300° F under conditions of constant stress. The average grain diameter varied between 9 and 190 p (ASTM 10.7-2). The subgrain size and apparent activation energy for creep were not found to depend in any systematic manner on gain size. Grain hozmdary serrations were observed in all specimens tested. The variation of the secondary-creep rate, 2,, with the pain diameter, 1, is given by: es = K(213m + 1 )/l.]; 1, is the grain diameter zohere is reaches a minimum. Results in the literature shoujthat 1,increases as the temperature increases. At low creep temperatures is is therefore proportional to 12, at intermediate temperatures <, exhibits a minimum, and at high creep temperatures is is proportional to 1/1. The dependence ofis on the stress, u, is given by: t, = A" (sinh acrln, a and n show little variation with 1. The dependence of A" on 1 is given by: A" = KA[(21k + 13)/1]. For 1 » >>lmn = 4, and at constant values 01- isat lozu stress levels, the steady-state stress is given by the Hall-Petch relation. The variation of c, with grain size is believed to he associated particularly with grain boundary generation of dislocations which becomes more important with increasing temperatures. SEEMINGLY inconsistent experimental findings have led to a certain amount of confusion concerning the effect of grain size on creep behavior. The confusion is attributed to a lack of test results obtained over sufficiently wide ranges in grain size, stress, and temperature. Experimental results presented in this paper and results available in the literature1-5 show a consistent behavior and lead to a unified concept for the dependence of secondary-or steady-state creep rate on grain size. In accordance with this concept, which is substantiated experimentally, secondary-creep rate should increase with increasing grain diameter at low creep temperatures, leading to greater creep strengths for fine-grained materials. At intermediate temperatures the secondary-creep rate should decrease to a minimum and then increase as the grain size is increased. At high creep temperatures the secondary-creep rate should decrease with increasing grain size, leading to greater creep strengths for coarse-grained materials. Whether a temperature is high or low for creep in a metal or alloy depends primarily on its melting temperature. MATERIAL AND TEST PROCEDURES The material tested was an austenitic iron-base alloy of the following composition (wt pct): C, 0.005; N, 0.017; Mn, 1.26; Ni, 14.21; and Cr, 17.18. Two 15 -lb ingots were forged and hot-rolled to 5/8-in.-diam bars which were then cold-rolled and cold-swaged to a diameter of 0.49 in. These were sectioned into 3-in.-long blanks and heat-treated at various temperatures to obtain different grain sizes. The procedures employed and the results obtained are summarized in Table I. The secondary treatment at 1400° F followed the primary treatment without intermediate cooling to room temperature. This final treatment was employed to minimize various effects arising from heating to different temperatures during the primary treatment, particularly differences in intragranular dislocation structure, segregation of interstitial atoms at grain boundaries, and density of grain boundary ledges. The intragranular dislocation structure was examined by electron transmission metallography after each of the treatments described in Table I. Isolated dislocations and a few tangles were observed but no evidence of subgrains was found after any of the treatments. No grain-size effect was evident on the density and distribution of dislocations. Stabilization of grain boundary structure is particularly important because, as will be discussed later, grain boundaries influence high-temperature creep behavior. Magnetic-permeability measurements after each treatment and

Jan 1, 1964

By F. E. Wood, H. W. Young, A. W. Buell

This paper summarizes the results of laboratory tests conducted to determine the properties of the paraffin or rod-wax encountered in the Salt Creek field, Wyoming. It also describes field tests and methods employed to cope with the paraffin problem. The conclusions to bo drawn from the laboratory work are: 1. Samples of Salt Creek paraffin range in consistency from soft lo hard, the melting points varying from 120" to 156" V. 2. Masses of soft paraffin are soluble to an appreciable extent in crude oil and its liquid fractions at temperatures somewhat below the melting point of the paraffin. Hard paraffin is very slightly soluble. under these conditions. 3. Agitation apparently increases the amount of paraffin that will go into solution. 4. Paraffin congeals from solutions upon cooling to the point of saturation ation, which is in all cnscs below thc melting point of the paraffin. 5. Crutltl oil is tlie most effective. of all the solvents for holding paraffin in solution. 6. Pressure alone does not appreciably affect the solubility of paraffin in crude oil nor does it aid materially in holding paraffin in solution when the temperature is reduced. 7. Natural gas in solution under pressure does not appreciably increase the solubility of paraffin in crude oil, hut is effective in holding paraffin in solution when the temperature is reduced. 8. A foreign body introduced into a solution of paraffin in oil is imrnediately coated with paraffin if the temperature of the solution is at or below the melting point of the paraffin, and the object is considerably cooler than the solution. It may not be entirely correct to ray that paraffin is taken into solution; it is impossible that the paraffin may be in suspension rather than in solution.

Jan 1, 1928

By ALFRED T. BARR

In certain areas of the New Cornelia pit, considerable secondary blasting is necessary to reduce oversized boulders, formed from primary blasting, to pieces which will pass the 41/2-cu yd dippers on the shovels. Some of the boulders are &apos;dobied, but when time permits they are blockholed and blasted. In most instances one hole drilled to a depth of 2 to 3 ft and blasted with 1/3 to 1/2 of a stick of powder will break a boulder satisfactorily. Blockholing is normally done by using a jackhammer of the 55-lb class, 1-in. round drill steel, and detachable steel bits, 2-in. gauge when new. A bit change is usually made after the completion of each hole. The use of light drilling equipment in blockholing is desirable, both from the standpoint of safety and ease of doing the work, and when it was seen there was a possibility of using a lighter jackhammer through the use of tungsten-carbide bits and at the same time get at least the same drilling efficiency as with the standard equipment, it was decided to test tungsten-carbide bits. The claims for long life of the bits and footage drilled before resharpening gave hopes of eliminating much of the delay time in changing bits which is unavoidable with the use of steel bits. and thus gain in actual drilling time.

Jan 1, 1949

By Edward L. Wilson, Keshavan Nair, Ranbir S. Sandhu

In planning and designing of underground excavations and construction, it is of considerable importance that the stresses and displacements in the rock mass subjected to arbitrary sequences of unloading and loading be within allowable limits. For determination of the stress and displacement fields, the usual approach is to treat the rock as an elastic material and to apply the principles of the theory of elasticity. However, analytic solutions are available only for a limited class of problems of simple geometry and idealized material properties. Nonhomogeneity and anisotropy of material coupled with complex geometrical configuration and initial stress fields that are almost always preexistent in rock masses at great depths, render the problem intractable by analytical methods. Approximate solution techniques using numerical procedures have, therefore, to be resorted to. The finite element method as applied to plane stress analysis was introduced by Clough.1 It has developed into a powerful tool for the analysis of various field problems in structural and continuum mechanics. The method is well documented in the literature2-6 and, therefore, its historical development will not be discussed here. Wilson&apos;s analysis of the plane stress/strain problem has found extensive use in the area of soil and rock mechanics including stresses around underground openings; stresses and displacements in dams, foundations, etc.7-11 In his analysis of the axisymmetric solid,3 Wilson proposed a procedure to allow for certain cases of nonlinear material properties. In this chapter, the develop-

Jan 1, 1972

Thomas T. Read, New york, N. Y. (communication to the Secretary *):—At the meetings of English technical societies it not infrequently happens that, during the discussion of a paper, someone will arise to say that although he highly appreciated the material presented, nevertheless he believed it would have been better if some other phase of the question had been more highly emphasized. Assuming that this form of discussion is permissible in the Institute, I should like to reiterate the point made by Prof. A. J. Moses that conclusive proof of the identity of the minerals in question is an essential feature of the study of ores in this way. This is also expressed by Paul Krusch in his recent valuable paper on the sulphide ores (in which he arrives at conclusions diametrically opposed to those of Mr. Graton), as follows: "The diagnostic properties of the various ore minerals are known to but a limited circle of investigators." Many earlier investigators began the study of ores beneath the microscope by reflected light, but discontinued their work, in most cases, because they were unwilling to undertake the great amount of preliminary work necessary to securely establish a basis for their inferences. It is evident that Messrs. Graton and Murdoch realize that the promised later paper on diagnostic characters will be the more important of the two, but the point should be emphasized to forestall a flood of literature from other investigators who may gain the impression that the brief survey of polished specimens is a vade mecum to incontrovertible conclusions as to any given ore deposit.

Jan 1, 1914

Roof Bolts An expansion shell and plug Westinghouse roof bolting assembly made for use with threaded steel rods and large flat washers or steel channel employs a plug larger in diameter than those for trolley wire service. The notched plug helps prevent shell and plug from turning. The unit is shipped complete. Circle No. 1 Fan The Jeffrey Mfg. Co. Aerodyne Midget fan is a self contained blower or exhauster for auxiliary ventilation through tubing. Operating rating with 5 hp motor is 6.5 in. maximum static pressure, and 6200 cfm free delivery volume. Weight is 340 to 475 lb and it may be furnished in open or permissible form. Circle No. 2 Heavy-Density Initial installation in the Mesabi Range country of the Wilmot-Daniels heavy-density concentrating system was a 175 ton per hour plant at the [ ] Skubic Bros. Virginia, Minn., operation. This Wilmot Engineering Co. unit has a separatory vessel providing unidirectional medium flow and as the only moving part uses a standard drag-line conveyor for lifting sink out of the bath. Circle No. 3 Portable pH Meter A low priced battery-operated portable pH meter of utmost simplicity announced by the Photovolt Corp. uses only 3 ordinary radio batteries which give over 2000 hours of service. Accuracy of 0.03 pH is claimed by the manufacturer for the model 125, and AC power line supply is available. Circle No. 4

Jan 1, 1952

By J. Laskowski, Z. Sadowski

The properties of quartz, calcite, magnezite and dolomite suspensions prepared from -30 µm size fractions of these minerals have been investigated. Selective coagulation of the quartz-calcite, quartz-magnezite and quartz-dolomite binary suspensions was possible at the pH values slightly above those for the i.e.p. of the carbonate minerals. The tests revealed that quartz suspensions were not flocculated by the anionic flocculants, whereas the same polymers were flocculants for calcite, magnezite and dolomite. Selectivity in the flocculation of the quartz-calcite, quartz-magnezite and quartz-dolomite binary suspensions was not, however, satisfactory because of the activation of quartz by ca2+ and Mg2+ ions. Dispersing reagents can be used to improve the selectivity of flocculation.

Jan 1, 1980

By S. C. Termes, P. E. Richardson, R. L. Wilfong

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble cross-linked starch xanthate (ISX). ISX is insoluble, has a shelf life of more than a year when kept cold, and has a higher molecular weight due to cross-linking than the soluble, non-cross-linked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines, but no silicious gangue. Floc formation, floc size, and settling rate are dependent on pH. The pH dependence, however, differs for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1984

By George C. Stone

AS most of you probably know, Australia has had many strikes. The two places that had the worst reputation were the Broken Hill mines and Port Pirie, where the smelter was located. About four or five years ago, the smelter changed hands. The new proprietors - immediately endeavored to get on better terms with the men and made such progress in that respect that, the men came to them and said, "There is no use giving us any more money. You have just raised our pay one- bob a day, but the store-keeper and the boarding-house keeper have raised their prices. The boarding housekeeper raised our board three bob a week and the storekeeper took the rest of it and we are no better off." Learning that what the men needed most was firewood wood the company bought the wood on a tract of ground across Spencer&apos;s Gulf and- sent men over to cut it. The wood was brought to the works and given to a man to cut up. He thought he had an easy job and loafed, but when the committee representing the men discovered that his loafing added to the cost of &apos;the wood, it promptly disciplined him and made -him work as he had never worked before. The next question that arose was the distribution of the wood. The committee got bids from several cartmen whose prices varied from about two to five shillings. It gave the work to the next to the lowest bidder. The fact that if delivering the wood cost more, the user would have to pay for it, was an entirely new idea to the men.

Jan 1, 1920

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world&apos;s mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which" are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep-resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing&apos; together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is one of the most important minerals, was omitted because not more. than one or two per cent of the world&apos;s production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By F. Keller, A. H. Geisler

Some of the important changes that take place in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrystallization. Although improved metallographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based on the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mahl3-17 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chemical or anodic treatment. After removal from the metal sample by one of the special techniques described by Evans,19 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,17 nickel,7 iron 3,8,9 and a nickel-beryllium alloy" by heating; films formed on iron 8.9 by chemical action; and films formed on aluminum3-16 by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944