Search Documents

By J. P. Savely, D. E. Nicholas, R. D. Call

Progress in the technology of slope design over the past 15 years now permits the selection of rational slope angles if suitable data on geology, hydrology, and rock properties are available for a specified project. Although a full-scale slope design study remains the best course of action, there are situations where an extensive study is not feasible due to time or budget constraints. Two typical examples are: (a) selecting pit slope angles for a preliminary feasibility study at the exploration stage; and (b) coping with a slope failure in an operating mine. In both instances, slope angles must often be chosen on the basis of data that are currently available or can be readily obtained. All too often during exploration programs, a feasibility study is initiated shortly before the decision deadline to drop the property or proceed to purchase. If the only existing data at this point are a few cross-sections at odd angles showing ore and waste contacts or a dog-eared map of the surface geology, there may not be time to collect and organize sufficient information for the design of slope angles. On the other hand, if during the drilling program geologic cross-sections were constructed and the structural data compiled in tabular form, rational slope angles could be computed within the allotted time.

Jan 4, 1977

By E. W. Davis

The: mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is important to the ore producers, hut since most of the ore in the Lake Superior district is owned or controlled by consuming interests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations lor these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must he studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica! alumina, manganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accurate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both themselves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers. Recently a paper was read before the Eastern States Blast Furnace and Coke Oven Association, by Mr. G. W. Hewitt, Manager Production, Blast Furnace and Coke Oven Department, Wheeling Steel Corporation, in which he explained how his company determines the relative values of different grades of Non-Bessemer ore. This is a very important paper, perhaps not so much on account of the actual calculation methods described as because of the fact that premiums and penalties are shown on Non-Bessemer ores for silica, alumina, phosphorus, and manganese. As pointed out by Mr. Hewitt, the premium and penalty system described may not apply without adjustments to other smelting plants. However, if the various ore

Jan 1, 1941

By E. W. Davis

The: mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is important to the ore producers, hut since most of the ore in the Lake Superior district is owned or controlled by consuming interests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations lor these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must he studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica! alumina, manganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accurate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both themselves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers. Recently a paper was read before the Eastern States Blast Furnace and Coke Oven Association, by Mr. G. W. Hewitt, Manager Production, Blast Furnace and Coke Oven Department, Wheeling Steel Corporation, in which he explained how his company determines the relative values of different grades of Non-Bessemer ore. This is a very important paper, perhaps not so much on account of the actual calculation methods described as because of the fact that premiums and penalties are shown on Non-Bessemer ores for silica, alumina, phosphorus, and manganese. As pointed out by Mr. Hewitt, the premium and penalty system described may not apply without adjustments to other smelting plants. However, if the various ore

Jan 1, 1941

OFFICERS AND COMMITTEES OF LOCAL SECTIONS AIME Committee on Local Section Affairs Roger Pierce, Chairman Carleton C Long Thomas C Frick AIME Committee on Student Chapter Affairs John P Nielson, Chairman John C Calhoun, Jr J R Van Pelt, Jr Council of Section Delegates A A Burr, Chairman (Hudson-Mohawk) Ralph A Watson, Vice-Chairman (North Pacific) L G Neely, Secretary (West Central Texas) INTERIM COMMITTEE M O Langham (East Texas), Fulton J Olivier (Delta), L W Smith (Niagara Frontier), G R Spindler (Central Appalachian) LOCAL SECTIONS (There are 78 Local Sections in the United States, 9 Foreign) ADIRONDACK Established June 18, 1952 Official year begins in April Meets fourth Saturday monthly, April through October Seven meetings annually Local Section Dues AIME Members $2, Nonmembers $3 Charles F Dievendorf, Chairman Severn P Brown, Vice-Chairman George E Erdman, Secretary-Treasurer Gouverneur Talc Co , Inc Gouverneur, N Y Malcolm V Lowry, '60, Section Delegate Committees Membership David J Crawford, Chairman Program Brower Dellinger, Chairman Student Affairs Eugene A Eastman, Chairman

Jan 1, 1959

By S. C. Termes, R. L. Wilfong

As part of an effort to provide basic data on the fundamental scientific and engineering principles of minerals beneficiation, the Bureau of Mines is conducting research on the flocculation of mineral fines. This paper presents results of studies using cross-linked starches containing carboxyl, diethanolamine, iminodiacetic acid, and xanthate groups to flocculate hematite, goethite, chromite, manganite, pyrolusite, cuprite, and cassiterite fines. The carboxyl and xanthate derivatives flocculated all minerals except cassiterite; the latter was flocculated by only the diethanolamine derivative. The imlnodiacetic acid derivative flocculated hematite, goethite, chromite, cuprite, and pyrolusite fines. Zeta potential measurements were made to help define the reaction mechanism responsible for flocculation. These measurements indicate that electrostatic attraction probably is not involved, except possibly in the case of the diethanolamine derivative. The separation of hematite from quartz by selective flocculation with chelating crosslinked starches under two pH conditions and with two dispersing agents is described. Best recoveries and grades were found when either the carboxyl or xanthate derivatives was added at the natural pH of the pulp in the absence of a dispersing agent.

Jan 1, 1984

By B. W. Frazier

At a recent meeting of the North of England Institute of Min ing and Mechanical Engineers, during a discussion upon the com pression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

Detailed Geology of Certain Areas in the Mineral Hill and Warm Springs Mining District. By A. L. Anderson. T. H. Kilsgaard and V. C. Fryklund. Jr. Idaho Bureau of Mines and Geology. University of Idaho. 73 P. Maps, Illus.-Divided into three parts, this pamphlet covers the geology and ore deposits of the Hailey-Bellevue Mineral Belt, the Triumph-Parker mine mineral belt, and the ore deposits of the Mayflower Area. Numerous maps and illustrations are included for each area. Government Administration of the Copper Industry, World War 11. By John W. Douglas. 1950.51 P. $1.-This pamphlet covers in detail all the steps relating to control and operation of copper and copper products, and is of particular interest to primary producers, brass mills, wire mills, and foundries. Of particular current interest is the booklet's coverage of the steps leading to the Controlled Material Plan, into which industry is now once again heading. Copies can be obtained for $1 from John W. Douglas, Republic Foil & Metal Mills Inc., 55 Triangle St., Danbury, Conn.

Jan 12, 1951

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By AIME AIME

AT A meeting of the Boston Local Section of the Institute, on Oct. 3, approval was voted to the work done by its representatives on the Committee opposing the passage of a bill by the, Massachusetts Legislature to license engineers. The report is as follows: The Joint Committee on Licensing of Engineers, which included a Committee of the Boston Society of Civil Engineers and representatives of seven other societies,* submitted to the members of the respective societies, on Jan. 8, 1921, a report in which it was stated that on Jan. 4, 1921, a petition was filed in the Legislature of Massachusetts by the Boston Chapter of the American Association of Engineers accompanied by a bill to provide for the registration of professional engineers and land surveyors. This report also stated that at a meeting of this committee, held on Jan. 7, 1921, it was voted:

Jan 1, 1921

By John L. Schroder

The demands for increased productivity on the 1967 coal industry have generated new operating trends and fresh approaches to old methods, which have enabled the industry to keep pace with the expanding economy. Changes, while not radical in concept or design, have been plentiful and are marked by the refinement of the already tried, tested and proven. Perhaps not since World War II have there been demands on equipment manufacturers to design and deliver such diversified types of machines as those required by the industry in the past year. Equipment developments-following a plan which calls for higher productivity, lower maintenance costs and greater machine availability- have tended more toward increased horsepower and heavier, more rugged equipment. Electrical and mechanical components, designed in many instances with maximum reliability rather than initial costs as the main criterion, have contributed to the improvements in over-all performance. High-strength, specialty steels are finding use in a wide range of equipment applications. The horsepower capacity of electric motors being installed is more frequently being rated on a continuous basis rather than the former one hr or less and, as a result, fewer failures now occur because of overloading. These developments reflect the pyramiding cost of equipment down-time and represent definitive progress in reducing the magnitude of the problem.

Jan 2, 1968

By J. D. Rice, P. L. Wearden, W. L. Hensou

Solutions to the unsteady-state partial water-drive reservoir performance problem can be obtained through the use of analogue computers or high-speed electronic digital computers. The solutions that have previously been resolved for use on digital computers, however, demand a knowledge of the aquifer parameters. Generally, the analogue computers now in use do not require this knowledge. A solution is presented herein where the aquifer performance, expressed in terms of difference equations, is related to the reservoir performance as expressed by the modified Scbiltbuis material-balance equation. A numerical procedure for a medium-sized digital computer also is presented in which a solution to the set of equations defining the aquifer and reservoir performance is obtained and the aquifer parameters (permeability and sand thickness) are automatically optimized while simultaneously matching the known pressure behavior. Predicted pressure behavior can be calculated using rates from any assumed future production practice. The procedure provides an output format which presents the cumulative, incremental and average rate of natural water influx, the per cent gas-cap expansion, the calculated reservoir pressure, the measured reservoir pressure, and the difference between the measured and calculated pressures. Results of a test problem are presented in comparison with results obtained by the Bruce Analyzer, Ohio Oil Co. 's Pace General Purpose Analogue Computer, and Sun Oil Co.'s Single-Pool Electronic Reservoir Analyzer. These results indicate that unsteady-state reservoir perlormance for a single-pool system can be adequately simulated by a numerical method employing a digital computer and that the special-purpose analogue computer can be supplanted by this method. INTRODUCTION The numerical approach to the unsteady-state partial water-drive reservoir performance problem heretofore has been limited in that solutions have been resolved only for certain fixed parameters. Also, prior to the advent of high-speed electronic digital computers in the last few years, calculations were so tedious and time-consuming that they ordinarily were neglected, or some other means of obtaining the solutions were used. The analogue approach had been used for obtaining solutions to the transmission-of-heat problem and, consequently, means were developed for applying the electrical analogue to the unsteady-state reservoir performance problem. Bruce submitted a paper for AIME publication in Sept. 1942, in which he described an electronic device (now called the Bruce Analyzer) for analyzing the water-drive performance of any reservoir, based on either steady or unsteady-state flow characteristics. 1 Sun Oil Co. adopted the analogue approach in 1949 and now has two special-purpose high-speed electronic reservoir analyzers in use.2,3 Two main features of Sun's analyzers are (1) the high repetitive rate of reproducing the entire history of reservoir performance cyclically a number of times per second, and (2) the elimination of the necessity of knowing the properties of the associated aquifer. Since the advent of larger and faster digital computers, the possibility of incorporating this second feature into a numerical approach appeared feasible. Previous work has been done and material published covering the application of numerical methods to the behavior of the pressure with respect to time at any point in an associated aquifer? However, the aquifer parameters must be known from some source. The material presented in Ref. 4 has been used to a great degree in developing the numerical method described herein. DIFFERENTIAL EQUATION AND BOUNDARY CONDITIONS The problem of simulating the performance of a reservoir and the associated aquifer is to determine the characteristics of the aquifer such that the

By R. G. Knickerbocker

A STURDY and consistent expansion of the metal industry occurred in 1947 exemplified by an increase of approximately 30 per cent in steel consumption over 1946. For this major reason, ferroalloy metals have seen their most useful and important peace-time year. The current domestic rate of consumption of high-grade ferroalloy ores, together with added consumption of new foreign producers as well as for eign nationals' restrictions on high-grade exports, makes very evident the increasing difficulties of obtaining sufficient high-grade ores. This accentuates the need for new and less expensive methods of production of ferro-alloy metals of higher purity from lower-grade domestic resources. As an important factor in preparedness, procurement of these high-grade, -critical ferroalloy minerals and metals for our nation's stock piles is a most important task. Also, this stock-piling can be the means of supplying incentive for the industrial development of the new metallurgical processes and plants necessary for the recovery of ferroalloy metals from our domestic low-grade deposits.

Jan 1, 1948

By L. Bombardieri, H. F. Mills

Iron King mine, producing gold-silver-lead-zinc-ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pat tern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length, with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth, the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 5 ½ -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material.

Jul 1, 1956

By Eugene A. Mizikar

A mathetnatical model of heal transfer in continuously cast steel slabs is described. The model, consisting of a unidimensional transient conduction equation and boundary condition equations, has been pvogrammed for computer solution. Temperatuve and solidification profiles calculated for a 6-in. slab, being cast under several conditions of secondary cooling, are presented and compared. Calculated solidification profiles are in agreement with reported expevinle~ztal values. For the mold zone, the predicted slab shell thickness can be described by: Resuilts of the study indicate that multibank spray cooling followed by radiant cooling should be employed when solidifying thick slabs with minimum surface temperature of 1600°F. Under these conditions, a 6-in. slab can be expected to solidify in about 8.3 min. Computer results also indicate that radiant cooling can replace spray cooling during solidification of the final 30 pct of slab with little increase in overall solidification time. CONTINUOUS casting has come to the forefront of the steel industry in recent years because of economic advantages resulting from increased yields and elimination of several processing steps. Considerable work, however, remains to be done regarding modifications to the process and operating procedures. Both a lack of operating plants in this country and the experimental difficulties associated with direct measurements on moving castings have made determination of solidification rates and temperature distributions difficult. An alternate approach is to mathematically simulate heat transfer in a continuously cast section, and then calculate the temperature distributions as a function of the controllable variables of the process. Simulation of heat transfer during solidification requires that a nonlinear mathematical problem be solved. As pointed out by Ruddle,' there are two mathematical approaches to the problem- the analytical approach and the numerical approach. While the analytical approach is certainly the more elegant of the two, it does require a number of inexact assumptions because of the complexity of the problem. For example, noteworthy analytical treatments of heat transfer in continuous casting have been developed by Savage Hills,3 and pehlke4 only by making one or more simplifying assumptions such as invariant thermophysical properties, constant heat-transfer coefficients in the mold, and linear temperature profiles in the shell. Simplifying assumptions such as these can introduce considerable uncertainty in the validity of results calculated with analytical solutions. Numerical solutions, which are considerably more versatile, appear to be better suited for solving solidification problems. Complex variations in the boundary conditions and variable thermophysical properties can be handled readily with this technique. Whereas numerical computations can be long and tedious when done by hand, results can now be obtained quite rapidly with the use of either the digital or analog computer. Several numerical models of heat transfer in continuous casting have been published. In 1963, Adenis, Coats, and Ragones published a numerical model used to calculate temperature distributions in direct-chill-cast magnesium billets. More recently, Donaldson and Hess 6 presented results obtained with a numerical computer model of heat transfer in continuously cast steel billets. In the present study, a model of unidimensional heat transfer in continuously cast slabs is presented. The method of solution on a digital computer is also included. Calculated temperature distributions and solidification profiles for various schemes of secondary cooling along with attempts to verify the model are also discussed. MATHEMATICAL MODEL The schematic representation of the slab continuous casting process in Fig. 1 illustrates that the slab passes through three distinct zones of cooling. Accordingly, the mathematical model consists of three parts: 1) solidification in the mold; 2) solidification in the spray cooling zone ; 3) solidification in the radiant cooling zone. Heat-Transfer Equations. The model was developed bymaking a heat balance on a horizontal slice of slab over the time period required for the slice to proceed from the liquid metal meniscus in the mold to the cutoff station. As shown in Fig. 2, the imaginary slice extends from the center line to the surface of the slab. As the slice moves downward, heat is conducted from the center line to the surface of the slab at a rate governed by the surface boundary condition and thermophysical properties of the metal in the slice. The following partial differential equation describes the conduction of heat in a medium moving at velocity U in direction Z:

Jan 1, 1968

We have seen that the first coal development in Pennsylvania was in the Pittsburgh bed in the southwestern corner of the state. The next mining, in point of time, was done in Clearfield County along the West Branch of the Susquehanna River, but the amount of mining done was quite small for a number of years and was soon exceeded by that from the area north of the Susquehanna River in Tioga, Bradford and Lycoming Counties, which will be considered now. It is claimed that coal was first noticed in Tioga County, in 1792, by Robert and Benjamin Patterson who were leading a party of settlers from Williamsport to southern New York, and while clearing a road near the site of Blossburg, found coal, which was said to be good. About 1815 David Clemons made an arrangement with Aaron Bloss, owner of the land, to work some of the coal and hauled the first load down the river to Painted Post, N. Y., as there were no available markets in his own state. Smiths found it an excellent fuel and apparently he found a ready market for the small amount he could transport by wagons and sleighs. As wood began to become scarce around the towns in New York State, the knowledge of the coal deposits in the mountains at the head of the Tioga River attracted attention to the field and the necessity, for means of transportation from it. Some coal had been floated down the river, but navigation was uncertain and dangerous. In 1827 an iron plant was built, and to ship its product and coal, it was proposed to build a canal along the river to reach Corning, N. Y. A company had been chartered in 1826 in Pennsylvania to "make a navigable canal or slack-water navigation" to the state line and coal was shipped on rafts of logs, both being sold, during highwater. In 1828 the company was authorized to build a railroad instead of a canal, and in September 1840, the railroad was completed from Corning to Blossburg.1 That some coal from Pennsylvania had been reaching southern New York towns prior to the improved means of transport is shown by the report of a committee to the New York Assembly: "the bituminous coal has been brought to us either from Great Britain or from that part of our own country which borders on, and lies west and south of the Susquehan-

Jan 1, 1942

By D. C. Jackling

I BESPEAK your indulgence for a brief expression of the views of a patriarch in the field of mineral industry technology relative to young men's problems in that sphere of education and endeavor. Wherever hereafter I employ the terms "technical education," "engineer," "technologist," or similar expressions, these are intended to be understood as relating to the broad field of the sciences and arts applicable to the mineral industries. First, the usefulness of technical education to either the possessor of it or those to whom its services may be made available industrially depends primarily upon the quality of the education and the capabilities of the educated to put his talents to effective and constructive employment in his chosen field of applied science.

Jan 1, 1940

By David W. Brunton

Mine-drainage and the ever-increasing demand for water on the plains have within the past few years necessitated the driving of a great number of adits and tunnels, including many of considerable size and great length. In most instances, existing conditions have called for extreme rapidity of execution; and this necessity, coupled with the high altitudes at which most of the work has been carried on, excessive freight-rates, and difficulty of access, has involved many complex and interesting problems. One of the most rapidly executed undertakings of this class is the Laramie tunnel, recently completed for the Laramie-Poudre Reservoirs & Irrigation Co. This tunnel is driven through Green ridge, a spur of the Continental Divide, which separates the Laramie river from the Cache-la-Poudre in Laramie county, Colo. Green ridge is extremely persistent, and further northward in Wyoming is known as Sherman hill, the highest point on the Union Pacific railway. At the point where the tunnel is driven, two opposing bends bring these streams within 2.5 miles of each other, with a difference in elevation of 500 ft. The rock exposed on the banks of the two rivers does not differ materially in hardness; and, without a geological study of the conditions involved, it would appear that the difference in the depth of erosion of the two streams is due principally to the greater volume of water at this point in the Cache-la-Poudre, which has a drainage-area above the tunnel-portal of 110 sq. miles, as against 30 sq. miles of natural drainage for the Laramie. To increase the water-supply at the tunnel, however, this latter amount has been augmented by two side collection-canals, which bring the available drainage-area up to 84 square miles. The nearest railroad shipping-point to the eastern portal is

Jan 1, 1913

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

IN speaking, on the subject, "Engineer-Citizens," at the Lehigh Valley Mineral Industries Conference dinner, on April 26, at Easton, Pa., George Otis Smith, Director of the United States Geological Survey and President of the American Institute of Mining and Metallurgical Engineers, said in part: "It would be carrying coke to Connellsville to bring to the Lehigh Valley the idea that mineral resources are the foundation of national prosperity. Unfortu-nately, however, this obvious, fact is not everywhere recognized. Too many of our economists, journalists, statesmen and other dopesters of present business con-ditions stress the human factor so strongly that they overlook the material with which men work out their destiny. To them the financial psychology of Wall Street and the political logic of Capitol Hill and the business commonplaces of Main Street all loom far larger than the geology of the Lehigh Valley or the engineering triumphs of Bethlehem, or, the creative thinking at Lehigh and Lafayette. "The present situation in the industrial and .business world is a complex of interacting causes and reacting effects not easily itemized and entered on our trial balance sheet. But, chief among the liabilities of today is the excess of production capacity in most branches of industry. The farmer has no. monopoly in his desire for relief. Whether your professional connections are with steel or cement, coal or oil, copper, or zinc, you; know too well that for, the moment America is over-engined, and you keenly realize the ever-present hazard of industry speeding up regardless of the curves or grades just around the corner.

Jan 5, 1928