Search Documents

PRESIDENT WILLIAM KELLY, District 5 IRON MOUNTAIN, MICh PAST PRESIDENTS E P MATHEWSON, District 0 NEW YORK, N Y ARTHUR S DWIGHT, District 0 NEW YORK, N Y FIRST VICE-PRESIDENT J V W REYNDERS, NEW YORK, N Y TREASURER CHARLES F RAND, NEW YORK, N Y

Jan 1, 1923

By Bernt Ellingsaeter, Terkel Rosenqvist

IN the silicothermic reduction of magnesia, burned dolomite is treated with high grade ferrosilicon in an evacuated steel retort at temperatures between 1150° and 1200°C. The following reaction is assumed to occur MgO + CaO + 1/2 Si (Fe) - Mg(g) +- & Ca,SiO, + Fe with the equilibrium constant on the basis of thermodynamic data for the substances involved and assuming unit activity for all solid constituents, Kubaschewski and Evans' calculated the magnesium pressure as a function of temperature logp,, (mmHg) = 15.06-1.61 T- log T- 13,16O/T. Pidgeon and King," who measured the magnesium pressure by means of a flow method, found values about three times the calculated ones. This may be caused by uncertainties in the thermodynamic data, but may also be caused by the formation of other reaction products, such as Ca,SiO,, which is known to be the stable silicate in equilibrium with lime. Whatever the exact reaction may be, it is evident that as long as all other factors are maintained constant the magnesium pressure will vary with the silicon activity, viz: p,, = &,. (p,,) ", where (p,,)" is the magnesium pressure by the reduction with silicon of unit activity. In the present investigation, p,,, was therefore measured for various grades of ferrosilicon and their silicon activities were calculated. The experimental method was similar to that used by Pidgeon and King. Briquettes of burned dolomite and Fe-Si alloys were placed in a 1 in. heat resistant steel tube and were heated to 1200°C. By means of a flow of purified hydrogen, the magnesium vapor was swept into a condenser filled with steel wool. From the amounts of hydrogen used and magnesium condensed the magnesium partial pressure was calculated. First a tube of 28 pct Cr steel, and later a tube of Kanthal D (a ferrous alloy with 22.6 pct Cr, 2 pct Co, and 4.5 pct Al), was used as a heat resistant tube. The latter tube showed the best heat resistance. The dolomite used had the following composition: 43.6 pct MgO, 55.5 pct CaO, 0.2 pct K,O + NalO, 0.2 pct Fe,O,, and 0.3 pct insoluble. The ferrosilicons were prepared from 98 pct Si of technical grade (0.7 pct Al, 0.3 pct Ca, and 1 pct Fe) by melting with various amounts of electrolytic iron of high purity. The alloys thus obtained were analyzed on their iron and silicon contents, which added up to between 99 and 100 pct. The amounts of reactants were chosen so that there would always be an excess of the oxides, and the average decrease in silicon content during the experiments would be about 1 pct. Most of the reaction occurred in the part of the reaction mixture facing the gas flow. The change in the silicon concentration in the part facing the condenser was, therefore, negligible. To facilitate the reaction, about 1 pct fluorspar was added to the briquette mixture. Fluorspar does not enter the reaction, but is known to act as a

Jan 1, 1957

HOWARD N. EAVENSON, Chairman C. T. HAYDEN, Vice-chairman, Bituminous Coal Production CHARLES DORRANC~ Vice-chairman, Anthracite Coal Production HOWARD P. ZELLW, Vice-chairman, Evaluation of Coal for Coke Making W. H. F'LTLWEILER, Vice- Chairman Gas and Its Manufacture 3. B. MORROW, Vice chairman, Coal Preparation

Jan 1, 1928

By P. G. Shewmon, H. E. Collins

A study has been made to determine the sites at which sulfur adsorption occurs on copper surfaces. measurements were made of the relative torques, Ys, at the intersection of twin boundaries with surfaces near the three low-index orientations, i.e., (100), @lo), and 011), over a range of H2S/H2 ratios. HZS concerztvations j'ro~n 3 to 1500pp)n between 830" and 1050°C were used. It is concluded that sulfur adsorption occurved preferentially though not exclusively at edge sites near the (100) and (110) surfaces in the HzS range — 700 Ppm giving rise to negative torques near these orientations. Beyond this HzS range, adsorption occurred at all sites. Near the (111) surface, 7/y little with HzS concentration up to approxiwzately 75pptn. Above this range, the results indicate adsorption is occurring OH both terrace and edge sites. SCIENTIFIC interest in surfaces and their interactions with a gaseous environment dates back to the beginning of the 19th century. The scientific luminaries of that period—Faraday, Maxwell, Rayleigh, Dewar, and Gibbs—were already concerned about such processes. However, it has only been within the past several decades that adsorption on metal surfaces has been actively studied. This increased interest in adsorption has been brought about by the advent of new and improved experimental techniques and apparatus, e.g., ultrahigh vacuum, and field-emission and ion microscopes. However, most of the work done using these techniques has been carried out at low temperatures. When adsorption studies have been made at either low or high temperatures, they usually gave no indication of the particular surface orientations or type of sites on which adsorption was occurring. In the last few years, there have been a series of studies in which the surface tension, y,, and/or its derivative with respect to orientation, 7, have been studied as a function of orientation and atmosphere.'-7 Nearly all of the work on the relative torque,* ~/y, silver annealed in hydrogen and air.6 Recently Winterbottom and Gjostein" have used a modified and more accurate Mykurian method to determine the y plot of gold in hydrogen The only work in which T/~, has been measured over a range of chemical potentials for a given solute, p2, is that of Robertson and shewmon7 on the Cu-0 system. They measured T/Y, vs Po, (10"" to 10- l3 atm) at 1000°C in various mixtures of Hz0 and HZ. From this work they estimated the value of p2 at which one half of the surface sites are occupied with oxygen, pg, as being in the range 10- l6 to 10- l5 atm of oxygen. They also found that increasing Pa increased the magnitude of ~/y, near the (111) and (100) orientations. This indicates that oxygen is not adsorbed preferentially at step edges, but uniformly over all surface sites. In addition, they did one experiment on sulfur adsorption on copper surfaces, which indicated that sulfur adsorption decreases ~/y, near the (100) orientation, while not affecting ~/y, near the (111). This could be interpreted as indicating that sulfur adsorbs preferentially at step edges near the (100). In this paper the primary objective of the work has been to carry out a study of sulfur adsorption on copper surfaces over a range of temperatures and p,. In conjunction with this work, thermal grooving at grain boundaries has been examined as a method of determining the effect of sulfur adsorption on y,. METHODS Ideally, one would like to have information on the quantity of solute adsorbed on a surface and the types of sites at which it is absorbed as a function of p2. The total quantity adsorbed or the surface excess is given by the thermodynamic equation Thus data on the variation of y, with pz indicates the value of p2 at which adsorption becomes appreciable and the quantity adsorbed. The type of adsorption site is more difficult to deduce but information on this can be obtained from the variation of rz with 8, the angular deviation of the surface orientation. This is obtained from the thermodynamic equationlg Data on t and ys as functions of p2 have been obtained by the following methods. 1) Twin Boundary Grooving—By determining the effect of adsorption on the torque, 7, where T is the variation of surface energy, y,, with orientation, it is possible to obtain some indication as to the preferred sites of adsorption. Experimentally, the torque value measured is the relative torque, 7/ys The twin boundary grooving technique suggested by Mykura'' was used in this study to determine near the three low-index orientations— (loo), (110), and (111). Mykura's equation relates 7 /yS to measurements of the di-

Jan 1, 1967

By Y. A. Chang

Phase relationships in the system Cr-Si have been established based on the melting point, X-ray, metallo-graphic, and DTA studies. The three intermediate phases, Cr3Si, Cr5Si,, and CrSi,, melt congruently at 177V ± I@,Cr3Si, 1680"i 20°, and 1490" *20°C, respectively, while the fourth intermediate phase CrSi, melts peritectically at 1413" i 5°C to Cr5Si3 and a melt containing 51 at. pct Si. The temperatures and compositions of the four eutectic isotherms occurring in this system are given below: DTA and metallographic evidences indicate that Cr5Si, undergoes a phase transformation at 1505" i20°C. The high-temperature form of this phase could not be retained by the quenching techniques used in this study. TECHNOLOGICAL interest in the developing of composite systems, consisting of Sic on the one hand as a fiber-reinforced material and metallic substances such as chromium, nickel, or Cr-Ni alloys as a binding agent on the other hand, stimulated the present investigation of phase relationships in the binary system Cr-Si. Earlier works concerning this system have been evaluated and summarized by ansen and Anderko.' Their phase diagram was based mainly on the works of Kieffer, Benesovsky, and schroth2 and Kurnakov.~ According to these authors, the three intermediate phases Cr3Si, CrSi, and CrSi, all melt congruently at approximately 1730°, 1600°, and 1550°C. However, they did not agree on the compositional stability of the fourth intermediate phase between Cr3Si and CrSi. Later Parthe, Nowotny, and schmid4 determined the structure of this phase to be tetragonal T-1 type using the single-crystal method, and concluded that this phase had a formula of Cr5Si3. Since the compilation of Hansen and Anderko,' a new phase diagram for the system Cr-Si has been proposed by Elliott5 based on the works of Goldschmidt and rand,' Guseva and ~vechkin,~ and Trusova, Kuzev, and Ormont8 and the earlier works quoted by Hansen and Anderko.' According to this proposed phase diagram, all four intermediate phases have large ranges of homogeneity and all melt congruently. More recently, Svechnikov, Kocherzhinskii, and yupkog studied the system Cr-Si by the DTA-method. According to their findings, the three intermediate phases, Cr3Si, Cr5Si3, and CrSi,, melt congruently at 1700°, 1720°, and 1475"C, respectively, while the fourth intermediate phase, CrSi, melts peritectically at 1475°C to Cr5Si3 and a melt containing 50 at. pct Si. The temperatures and compositions of the four eutectic isotherms were found to be: In view of the discrepancies existing in the literature concerning the system Cr-Si, it was decided to rein-vestigate the phase relationships in this system. EXPERIMENTAL a) Starting Materials. Chromium disilicide and chromium or silicon powders were used in the present study to prepare the melting point and DTA samples. CrSi, was obtained by directly reacting cold-pressed elemental powders in an atmosphere of Hz at a temperature of about 1250°C. Chromium powder, purchased from Stark Chemical Co., had the following impurities in ppm: Fe, 200; Mg, 1000; and 0, 250; while silicon powder, purchased from the Welded Carbide Co., had the following impurities in ppm: Ca, 700; and Fe, 3500. b) Melting-Point Determination and Differential Thermal Analysis. Cylindrical melting-point samples of approximately 13 mm in diam and 30 mm in length with a rectangular groove in the center were prepared by hot-pressing of well-mixed powder mixtures in graphite dies. Before the melting-point determination, the hot-pressed samples were ground on a sand paper to remove any minute surface contamination of graphite. A small hole of 1 mm in diam, drilled on the center portion of the samples, served as a blackbody cavity for the temperature measurements. DTA samples approximately 13 mm in diam and 15 mm in length were prepared in a manner similar to the melting-point samples. Melting points were determined using the Pirani technique under a helium atmosphere of 40 psi. The design, performance, and operation of this apparatus have been described in detail by Rudy and ~ro~ulski.'~ The temperature measurements were carried out with a calibrated disappearing-filament-type micro-pyrometer. The measured temperature was corrected for losses from the quartz window of the melting-point furnace and for deviations from blackbody conditions of the observation hole. The procedure for temperature correction has also been previously described." The DTA method of Heetderks, Rudy and Eckertl' was also used to check any phase transformations of selected alloys in the system Cr-Si. It was not possible to make remated runs on the same sample once melt-

Jan 1, 1969

E P MATHEWSON, Disttrict 0 NEW YORK, N Y PAST PRESIDENTS EDWIN LUDLOW, District 0 NEW YORK, N Y ARTHUR S DWIGHT, District 0 NEW YORK, N Y FIRST VICE-PRESIDENT J V, W REYNDERS, NEW YORK, N Y TREASURER CHARLES F RAND, NEW YORK, N Y

Jan 1, 1923

By P. Chiotti, G. R. Kilp

IN the study of zinc-zirconium1 and zinc-uranium2 systems, vapor-pressure measurements were made in order to establish the equilibrium phase diagrams for a pressure of 1 atm. In each of these systems, only zinc has an appreciable vapor pressure over the temperature range investigated. The zinc pressure was measured over a sufficiently wide temperature and composition range to permit calculation of the standard free energy, enthalpy, and entropy of formation for the compounds ZrZn, ZrZn2, ZrZn3, ZrZn6, ZrZn14 , and U2Zn17. In these calculations the compounds were treated as line compounds. Although the exact composition range was not determined, metallographic and thermal data indicate that the solubility range for these compounds is small. It is to be noted that the compound initially reported to correspond to the formula UZn9, 2 has been shown by the crystal structure work of Makarov and vinogradov3 to correspond to the formula U2Zn17,. The crystal structure is similar to that for the compounds Th2M17, investigated by Florio,4 et al; here M represents iron, cobalt, or nickel. Therefore, thermodynamic calculations are based on the formpla U2Zn17 EXPERIMENTAL The dew-point method employed to measure the vapor pressure of zinc over uranium-zinc alloys has been described previously.2 The same procedure and apparatus were used in measuring the zinc pressure over zinc-zirconium alloys. In the case of alloys in the two-phase region consisting of a zirconium and the compound ZrZn, the Knudsen effusion method was employed to obtain a few values in the temperature range 600" to 560°C. In most cases, tantalum crucibles were used to contain the zirconium alloys. THERMODYNAMIC PROPERTIES OFU2Zn17 A least-squares treatment of the vapor-pressure data obtained for 35 and 65 wt pct U alloys in the temperature range 650° to 940°C gave lOg10PAtm = 7,713/T + 6.33 Here, as in following equations, T represents degrees kelvin and P represents the zinc vapor pressure in atmospheres. The probable errors for the two constants were calculated to be 60.68 and 0.0563, respectively. This relation represents the equilibrium dissociation pressure for the reaction U2Zn17 (s) - 2U(s) + 17Zn(v) The solubility of zinc in solid uranium is negligible and the only additional information required to calculate the free energy of formation of U2Zn17 is the free energy of vaporization of pure zinc. K. K. Kelley5 gives the relations, AF°= 30,902 + 6.03Tlog T + 0.275 X 10-3T2 - 45.03T

Jan 1, 1961

By J. S. Blakemore, E. O. Hall

SERRATED yielding, commonly called the Portevin-Le Chatelier effect, is known to occur in a wide range of alloys where the moving dislocations are considered to be locked by the diffusion of solute atoms to them. From the work of Cottrell,1 an approximate relationship between strain rate, E, dislocation density, p , and solute diffusion coefficient, D, giving rise to serrated yielding is: e =Dp

Jan 1, 1969

By A. Yoshikawa, T. Sugeno

To detenmine the origin of the sharp fatigue limit in many ferrous metals, S-N curvces were determined in push-pull fatigue at 18.6 kc per sec at room temperature and - 67°C for various kinds of iron. These differed in carbon and nitrogen content and grain size (25 and 2500 grains per sq mm). Sharp knees appeared in the S-N curves of fine-grained specimens with high interstitial content at both temperatures. In coarse-gruined specimens, knees were not sharp .regardless of the interstitial content and the testing temperature. It is concluded from these results that the controlling factov for the appeavance of the sharp fatigue limit is not strain aging but grain size. It has already been mentioned that iron and some iron alloys show fatigue curves characterized by a more or less sharp knee and a fatigue limit.' Explanations of the origin of this characteristic behavior of fatigue in iron appear to fall into two broad classes. One is concerned with interstitial impurities through the aging or locking effect and the other is based on intrinsic plastic properties of iron. Levy and sinclair2 and Lipsit and Horne3 have suggested that the fatigue limit observed generally in iron and steel is due to interstitial solute aging during the course of fatigue. On the other hand, Thompson and wadsworthl have suggested that the fatigue limit may be analogous to the sharp yield point, in the sense that alternating stresses above the fatigue limit are necessary to break down the dislocation locking. However, there are some experimental results which cast doubt on the general validity of these suppositions.4-8 Ferro and Montalenti' have recently suggested that the typical form of the fatigue curve of iron seems to come from an intrinsic plastic characteristic of the iron structure. This suggestion is based on the experimental result that pure iron containing an insufficient amount of interstitial solute to alldw appreciable strain-aging effects still showed a fatigue limit at room temperature. Although systematic investigations on the effect of grain size are scarce, it is thought that this effect is important in relation to the sharp fatigue limit. In fact, sensible differences were observed by Oates and Wilson4 in fatigue behaviors of a low-carbon steel depending on grain size. Ideally, the fatigue limit will be defined as the upper limit of stress amplitudes at which the life is infinite. This ideal fatigue limit can never be determined because of the limited time available for experiments, and moreover scattered data points often leave the construction of S-N curves somewhat arbitrary. And, it is usually stated that a material has a fatigue limit when its statistical S-N curve becomes apparently parallel to the N axis with a more or less sharp knee. The meaning of the fatigue limit and the sharp knee will be discussed in detail in relation to the construction of S-N curves. The origin of this sharp knee was investigated by determining S-N curves of iron for various interstitial contents, testing temperatures, and grain sizes. EXPERTMENTAL PROCEDURE The material as received was a commercial-grade low-carbon steel in the form of 4-mm-diameter rods with the following composition in weight percent: C, 0.09; Si, 0.017; Mn, 0.43; P, 0.006; S, 0.012; Cu, 0.11. Five different groups of specimens were tested. The grain sizes and interstitial contents in each group are given in Table I. The specimens of group C-02 were decarburized by annealing for 100 hr at 700°C, followed by an additional 100 hr at 850°C in wet hydrogen. Specimens of groups N-2 and N-9 nitrided in a mixed atmosphere of ammonia and hydrogen after an initial treatment identical to group C-02. The specimens of group C-9 were prepared in a manner similar to those of group C-02, except heat treatment was carried out in a vacuum. After polishing their surface with emery paper, the specimens of all groups were given a final anneal for 30 min at 930°C and air-cooled in an evacuated quartz tube. For group C*-9 this

Jan 1, 1965

By Wayne A. Greenwalt

A method that determines venture participation when the decision maker's level of risk aversion varies according to venture profitability and risk investment is presented. The decision maker's fundamental aversion to risk is established by the selection of a desired working interest for a venture that anticipates only a discounted payout.

Jan 1, 1982

By S. A. LoPilato, J. T. Smith

SEVERAL techniques have been evaluated for cooling the throat area of rocket-nozzle inserts to prevent erosion or fracture of the inserts during exposure to high operating temperatures and pressures. Self-cooled composites, such as infiltrated tungsten, have shown considerable promise for these applications. These composites can be fabricated by infiltrating the refractory matrix with a lower-melting metal or non-metal which is insoluable in tungsten. During firing, the lower-melting substance undergoes a series of continuous endothermic phase changes which absorb sufficient heat to maintain the nozzle matrix material at or below a safe operating temperature. At present, the state-of-the-art has reached a point where the refractory matrix density and microstruc-ture have been established as the critical parameters to be controlled for optimum self-cooled performance.'" Nondestructive testing has been utilized to ensure that porous tungsten billets were of uniform density and free from cracks or other defects prior to fabrication into rocket nozzle inserts. Ultrasonic-velocity techniques have been employed because of their reliability and reproducibility. The purpose of this note is to present and interpret the test data developed for porous tungsten matrices. For evaluation purposes, tungsten powders with Fisher subsieve sizes of approximately 4 and 18 p have been obtained for study from four commercial sources: the General Electric Co., Wah Chang Corp., Fansteel Metallurgical Corp., and Kennametal, Inc. Porous tungsten matrices were fabricated from the powders by hot pressing in induction-heated graphite die assemblies. Typical billets ranged from 3 in. diam, 2 in, high to 5 in. diam, 5 in. high. The ultrasonic-velocity measurement technique employed was through transmission, pulse echo at a frequency of 1.0 mc using matched barium titanate crystal transducers. The testing equipment included a pulsed ultrasonic generator, an amplifier, a specimen holder, and an oscilloscope, as shown in Fig. 1. The porous tungsten thickness was measured to i 0.0005 in, with precision micrometers while the oscilloscope achieved 0.02 psec time measurement accuracy. The time for a sound wave to pass through the billet, the bulk wave velocity, was calculated to 0.5 pct using Eq. [l]: V-} where V = bulk wave velocity, in. per psec, T = specimen thickness, in., and / = time, psec. To develop inspection standards, the bulk density of a porous tungsten billet was determined by the ASTM water-immersion technique.3 The ultrasonic-velocity measurements were completed at seventeen positions for each billet and averaged to develop a characteristic standard velocity for a particular tungsten powder at several density levels. A plot of ultrasonic velocity vs density is presented in Fig. 2 for six different tungsten powders. This graph has been established as

Jan 1, 1967

By P. A. E. Armstrong

For hardening, the steel should be heated just above the critical temperature, as a properly forged steel quenched from this heat has some toughness, with maximum hardness and density. The quenching bath should be kept at approximately a constant temperature. In drawing or tempering, longer time periods at lower temperatures are better than the shorter periods at higher temperatures. A recent questionnaire brought out the following facts: The double-arc, double-taper bit and cross bit give the best service; resharpening of the drill steels most frequently was caused by wear of gage; chipping of bit was, with one exception, the second cause; breakage of shank was with one exception, the third cause; upsetting of bit, upsetting of shank, and breakage of body were the fourth cause. The direct cause of the necessity of resharpening given was poor heat treatment first, and faulty steel and severe rock conditions second. Rock-drill Steel By N. B. Hoffman Much of the drill steel produced in America is manufactured into hollow rods. After all forging has been finished the entire bar should be thoroughly annealed and heat trcated before the point is hardened and tempered, at least where the drill has heavy duty, such as working in deep holes and hard rock. A large number of tools of like character and doing work requiring similar properties are now being made of alloy steels; for instance a steel with a carbon content of 0.75 to 0.85 per cent., manganese 0.25 to 0.35, phosphorus under 0.020, sulfur under 0.030 and vanadium 0.18 to 0.23 has proved very satisfactory for chisels. A steel of this type properly manufactured will be far superior to the ordinary carbon steels, while at the same time is one whose price range should not prove prohibitive. Much of the cutting efficiency of a drill depends on proper heat treatment. This vanadium steel has a far greater safe hardening and forging range than ordinary carbon steels, making it more nearly foolproof. It will harden nicely at 1400" I?. but will also harden well and satisfactorily at 1550" F. retaining its quality of hardness and toughness in either case. Drill Steel from Hollow Ingots BY P. A. E. ARmstrong Hollow drill steel is made from a drilled billet with a sand-filled core or the drilled, pierced, or the drilled and pierced billet, not sand-filled, is rolled down over a projectile or ball much the same as in ordinary pipe manufacture. The first is the method generally used in this country; the second is used largely in Sweden. Swedish hollow drill steel has a

Jan 1, 1922

By R. E. McNulty, R. D. Heidenreich, C. H. Gerould

TIIE electron microscope techniques and their application to magnesium alloys that are to be discussed in this paper are the result of research at The Dow Chemical Co. over the past three years. The view- point underlying the work is not wholly metallurgical, but has evolved through a variety of problems related to the physics and chemistry of surfaces. It can be said that the interest and stimulus were closely associated with a desire to employ effectively the electron microscope in research concerning the properties of solids as related to their physical structure. Only a portion of this work will be described here, and, consequently, many points of interest and debate are of necessity either only briefly recognized or are completely omitted. As has been pointed out by Desch,1 a great deal of the knowledge of the structure of metals has been obtained through microscopic studies of the surfaces of metallic specimens prepared in a particular manner. This information, when added to that obtained by means of thermal, electrical, X-ray, dilatometric and other methods, has been of great value both from a theoretical and a practical view- point. With the introduction of new instruments such as the electron diffraction camera and the electron microscope, it would be expected that still more information could be obtained. These two instruments have in many instances been very effective when directed toward the investigation of metallic surfaces, provided the proper methods of surface preparation were employed. Experience shows that the problems of surface preparation greatly limit the general application of these instruments to metallographic studies. It was found necessary to discard the standard metallographic procedures in applying the electron microscope to magnesium alloys and to work out new methods, which were required to satisfy certain conditions. These methods are unique to magnesium only in the specific chemical reactions occurring during etching. The presentation of the methods and results will be ordered as follows: I. Electron Microscopy of Surfaces. 2. Surface Preparation of Magnesium Alloys. 3. Discussion of Microstructures. a. Pure Magnesium and Single-crystal Studies. b. Types of Precipitation. c. Some Common Structures. d. Special Micrographs and Techniques. e. Structure of Mg-A1 Solid Solutions. 4. Correlation of "Fine Structure" with Corrosion Behavior of Magnesium Alloys.

Jan 1, 1946

By H. W. Hitzrot, R. H. Limons, L. V. Fegan

The testing of a new method for measuring pellet-bed temperatures in the traveling-grate or shaft furnace is presented in this paper. This method, using silver-palladium alloy wires as indicators, overcomes disadvantages existing in the methods based on the use of thermocouples which are costly and time-consuming. The authors have developed and tested a new method for measuring pellet-bed temperatures in the traveling-grate or shaft turnace through the use of silver-palladium alloy wires as indicators. This method overcomes the disadvantages of existing methods, which, based on the use of thermocouples, are generally costly and time-consuming. For example, in the case of the traveling-grate furnace, the installation of an instrumented pellet, together with its attached thermocouples, requires stopping the furnace, with resulting loss of production time. As for temperature measurement in the shaft furnace by the existing method, the movement of the shuttle-car feeder seriously interferes with both the actual insertion and the resulting distribution of continuously fed thermocouples. The authors have overcome these difficulties by using, as temperature indicators, a range of silver-palladium alloy wires that can be easily recovered, after firing at any desired location in a pellet furnace. Silver-palladium wires having specific melting points from 2000°F to 2500°F are enclosed in ceramic capsules. Each capsule is placed in a ni-chrome wire basket filled with a sample of green pellets, the baskets being the means for recovering the capsule after firing. After the encapsulated wires have been exposed to the firing cycle, the alloy wires are examined to determine the maximum temperatures attained by the pellet sample. This method gives accurate, rapid determinations of maximum temperatures attained during pellet induration in either the traveling-grate or shaft furnace The new method has the following advantages over existing methods: 1) it is less expensive; 2) no furnace downtime is required; 3) the testing units can, be made in quantity in advance; 4) measurements can be made in rapid succession at all desired locations; 5) measurements of maximum firing temperatures are more accurate; 6) on the basis of points 4 and 5, the new method gives a more reliable picture of the correlation of pellet quality, petrographic textures and maximum temperatures, thus providing a more effective quality-control tool. A disadvantage of the method is, of course, that the measurements are not continuous and only maximum temperatures are determined. TEST PROGRAM Preparation of Materials: CALIBRATION OF ALLOYS - In the following discussion the term "bead point" (see Fig. 1) refers to the temperature at which each alloy begins to melt and form a bead. Fig. 2 gives the bead point curve for silver-palladium alloys. Before the alloys are used in plant tests, the bead point of each alloy should be determined in the laboratory to verify the alloy compositions. Once a given alloy has been calibrated, it can be

Jan 1, 1965

By E. C. Dominguez, H. B. Scharf

The Sparrows Point plant of Bethlehem Steel Co., southeast of Baltimore, is the largest Bethlehem plant, with an annual rated capacity of 6.2 million ingot tons. There is considerable diversity of product, but a high percentage is sheet, tin plate, galvanized sheets, and rod and wire. The large amount of light-weight end product requires a number of pickling installations that necessarily consume large quantities of sulfuric acid. In the coking operations sulfuric acid is also consumed in recovery of ammonia as ammonium sulfate and in treatment of recovered light oil derivatives. Total sulfuric acid consumption in the plant is currently approaching 10,000 tons per month, of which 55 to 60 pct is required for pickling. In 1951 the acute sulfur shortage caused grave concern as to future sulfuric acid supply for the Sparrows Point plant. Raw materials for acid making were already at hand in the form of hydrogen sulfide and pyrites sufficient to produce nearly half the sulfuric acid required at that time. It was also known that the Bethlehem mining activities would produce additional pyrites in the future. Late in 1951 Bethlehem management decided to build a 250-ton sulfuric acid plant at Sparrows Point to utilize these raw materials. The plant was built and put in operation in May 1953. The steel plant has expanded considerably since 1951, and it is now necessary to operate the acid plant far over rated capacity in order to supply plant demand. Production of acid in 1954 amounted to 93,000 tons.

May 1, 1956

By John Lohrenz

Consider an investor who, knowing future costs and revenues, can choose how rapidly to produce from a given mineral source. If the investor elects to make that choice to maximize present value of future profits, how do policies affect the choice? Various alternative policies are examined. Some, such as higher royalty rates, lead to slower production rates than would otherwise obtain. Clearly, the chosen rates of production are policy-dependent. One is wisely counseled to consider how mineral policies affect the rate of production from given sources when analyzing current and alternative policies.

Jan 1, 1982

By Marston G. Fleming

E. C. Peterson (Anaconda Copper Mining CO., Darwin, Calif.)—A study of this quite comprehensible and interesting paper by Dr. Fleming brings to mind several observations in the practical application of alkalinity and related factors to the actual practice of lead mineral flotation. Soda ash has long been a widely used and a very helpful alkaline conditioning agent in the flotation of galena from the usual run of lead-zinc ores. Soda ash is one of the common "standard" conditioning agents tried in any laboratory investigation of lead-zinc ores because it has so often proved helpful to galena flotation. However, the use of soda ash in the actual flotation of oxidized lead ores is certainly not widespread. In the flotation of certain lead-zinc ores from the Park City district of Utah, it was found in the usual cyanide-zinc sulphate-xanthate circuit that soda ash had an effect of producing a very condensed and flat froth regardless of the many frothers tried and that substitution of lime for soda ash to produce the same pH (8.0 to 8.4) improved the froth condition. However, the flotation of coarse particles of galena became so critical that some would pass through into the tailing, but caustic soda as a substitute for either soda ash or lime produced a very desirable froth condition in the same pH range and greatly improved the metallurgical outcome. Milling was carried out in typically "hard water" from watersheds of limestone and other calcareous rocks and the ore also apparently contributed magnesium and calcium salts to the pulp. Certain lead-zinc ores of Mexico have shown their greatest flotation response in circuits conditioned with sodium bicarbonate, and such actual mill use was also believed to be related to the water necessarily used in milling. On other lead-zinc ores the optimum has been obtained in actual milling treatment by use of caustic soda in both circuits of the operation. In flotation of oxidized lead ores in which sulphidi-zation is employed by addition of sodium sulphide, very high pH's exist in the flotation circuit. With the usual oxide lead ores, demanding 5 to 15 lb of sodium sulphide per ton of ore, pH's in the circuit (closed and open water-circuits) may range from 9.5 to 12, and for ores that contain much anglesite or a high percentage of iron oxide minerals, sodium sulphide consumption may reach as much as 30 lb per ton of ore and the resultant pH will be correspondingly higher. Yet in such flotation treatment employing either xanthate or oil (high-sulphur crude oil or diesel oils) as the collector, satisfactory to excellent grades of concentrate and lead recovery are obtained. Although there have been great studies and accomplishments in the investigations of flotation fundamentals and flotation theory, and although an investigation to determine the effect of all factors entering into the actual plant flotation of sulphide and oxide ores must become very complicated, as Mr. Fleming has mentioned in his caution regarding the drawing of general conclusions for other ores, it seems that it would be of greater interest if the techniques and investigations could, with time, approach the conditions of actual practice and lead the way to improved and more efficient flotation plant performance. Marston G. Fleming (author's reply)—The gulf between fundamental flotation research and plant operation is, perhaps, less wide than Mr. Peterson suggests. For example, the work described in my paper developed from an extensive investigation of a complex lead-vanadium ore from southwest Africa. This investigation started as a standard ore-testing problem but, at almost every stage, results were obtained which could not be interpreted in terms of previous experience. A program of fundamental research was therefore undertaken and was closely interlocked with the ore testing. This coordinated investigation resulted in a flotation process which has now been proved by two years of successful plant operation, and although the grade and mineralogical constitution of ore as well as smelter requirements have altered more than could have been anticipated, our knowledge of the fundamental character of the problem has made it possible to meet each change in conditions with much more confidence than would have been the case had we neglected this aspect of the investigation.

Jan 1, 1954

By O. C. Holbrook, George G. Bernard

A new theoretical treatment has been obtained for the behavior of pattern waterflood injection wells when closed in. Two cases are treated: Case I where oil and water are assumed to have the same properties, and Case 2 where they arc different. In applying the method, one plots log (p — p,) vs closed-in time, where p is well-bore pressure at any tims and p, is static pressure. The value of p. is determined by trial and error as that value which makes the plot linear at large time. A value for the permeability-thickness product can be determined from the intercept of this linear part, and a value of the skin factor from the injection pressure at time of closing in. Application of the method to data from water floods at three fields seems to give reasonable results. For the case of unit mobility ratio, it is proved that this new method should give the same value for permeability-thickness product as the conventional pressure build-up method. In addition, the new method gives correct values for static pressure, whereas the conventional method does not, often indicating negative static pressures. The new method may be used in cases where the surface pressure persists after closing in as well as in cases where it does not. INTRODUCTION It is of considerable interest and importance to be able to determine the characteristics of the reservoir in an area surrounding a water injection well. Thus, if we can determine early in the life of an injection well that there is a considerable "skin effect", remedial measures can be started before a full-scale pattern flood begins. Similarly, if it can be shown that a gradual buildup of skin effect is occurring with time, measures to free the water of plugging material can be taken. Determination of static pressure in the water-injection well may show that the water is entering a thief zone and not the desired reservoir. Finally, determination of the permeability of the sand around the injection well will allow estimation of the future relation between injection pressure and rate. It should be possible to determine average reservoir permeability, skin effect and static pressure from pressure fall-off data. However, at the time we began work on this subject, it was thought that no adequate theory on which to base such determinations' was available. According to the conventional method which considers the reservoir to be filled with one fluid of small compressibility (see Van Everdingen, Joers2, and Nowak2), shut-in pressure is plotted vs log where is injection time, and At is closed-in time. The physical significance of injection time, may well be questioned in this case, since in a reservoir completely filled with a single fluid (as required by this theory) and with input and output rates equal, the pressure behavior after an initial transient is independent of t,. Attempts by our Tulsa area to use this theory led to negative values of static pressure in most cases. Because of these limitations of the method discussed above, it was decided to attempt to develop a new theory of pressure behavior in water injection wells, one which would apply when there is a gas saturation, as is so often the case in water floods. In the following treatment the assumptions and basic equations are given first, then the method of application of the equations. A complete example is given to clarify details of application. All difficult mathematics has been placed in the appendices so that the reader can follow the text without difficulty. However, if he wishes only to apply the results without knowing the basis for them, he can learn how to do this from reading only the sections entitled "Plotting of Experimental Results" and "Example." ASSUMPTIONS AND BASIC EQUATIONS Statement of Problem It will be assumed that a horizontal layer of constant thickness contains in its pore system a mixture of oil, gas and water. While water is being injected into this pore- system through a well at constant rate, an oil bank is built up, gas being expelled from the space taken by the oil as shown in Fig. 1. The saturations within each

By George Simkovich

It was hypothesized that solid-state point defects should alter the flotation properties of solids. Tests conducted on pure AgCl and AgCl doped with CdC12 show that atomic point defects exhibit an important role in the floatability of AgC1. Tests conducted on PbS doped with Ag2s or Bi2S3, also show that the defect structures resulting from these dope additions, i.e., a combination of electronic and atomic point defects, contribute significantly to the flotation of PbS. IT has been established that flotation occurs only when a finite contact angle exists between a solid and a gaseous bubble.' This angle, measured through the liquid phase, is expressed by the equation where the are inter facial free energies and the subscripts S, G, and L represent solid, gas, and liquid phases, respectively. As is seen in Eq. [I] three interface free energies, sG, sl, and GL, enter into the contact angle equation. Therefore, any variation in these energies which sufficiently varies the contact angle will, in turn, vary flotation processes. Changes made in any of the phases concerned, i.e., gas, liquid, or solid phase, are reflected through the changes occurring in two of the surface energy terms. Thus, a change in the liquid composition would be noted in sL and GL, and it is this phase, the liquid, which is most frequently altered in flotation studies., Changes in the solid phase must be reflected through the changes occurring in the sG and sL terms. In particular, it is hypothesized that changes in the surface concentrations of point defects in the solid-phase will alter the sG and sL terms which, in turn, will be reflected by flotation results. As an illustration of this hypothesis one may consider the defect structure and the flotation of AgC1. The bulk defect structure of AgCl is essentially one involving equal number of cation vacancies and interstitial cations.3 Upon adding CdC1, to AgC1, a greater number of silver ion vacancies are created in the bulk of the crystal.4 On the surface of the crystal the smaller binding forces and the free space accomodations may also allow for the creation of "surface interstitial anions", which will be designated as ad-anions. Thus, the point defect structure of the surface of AgCl doped with CdCl, will consist of cation vacancies and/or adanions. If the molecular forces responsible for the surface energies, ?SG and ?sL, are significantly altered by the presence of these surface point defects, then differences in flotation results will be noted as the concentration of these defects is varied. The defects present in AgCl are predominantly atomic in nature. In the case of PbS both electronic and atomic defects are present.5 This compound conducts electrically by either electrons or electron holes depending upon whether excess lead or excess sulfur is present. Upon disolving BiS3 in stoichio-metric PbS, one increases the concentration of cation vacancies and the number of electron carriers in the bulk of the crystal.5" At the surface, the possibility of ad-anions must also be considered. Conversely, upon dissolving AgS in stoichiometric PbS one increases the concentration of interstitial cations and the number of electronhole carriers in the bulk of the crystal.5,6' At the surface the interstitial cations will be designated as ad-cations. Thus, the point defect structure of the surface of a PbS crystal doped with Bi2S3 will consist of a number of cation vacancies and/or ad-anions and an excess of electrons. Conversely the point defects on the surface of a PbS crystal doped with Ag2S will consist of a number of ad-cations and an excess of electron holes. Again, as in the case of AgC1, should the molecular forces responsible for the magnitude of the interface free energies, ?sG and ?sL, be significantly altered by the presence of these surface defects then significant differences in flotation results will be noted as the concentration of these defects is varied. EXPERIMENTAL To test this hypothesis flotation tests were conducted on pure and doped AgCl and on PbS doped with either Bi2S3 or Ag2S. Preparation of the AgCl samples was performed as follows: AgCl and weighed amounts of CdC1, were melted in a porcelain crucible. The melt was then forced through a capillary tube and the particles emitted solidified in air as they fell about 1.5 meters. Spherical particles, -0.50 + 0.25 mm, were separated from the remaining solidified material

Jan 1, 1963

By J. J. Beeson

For the past fifty years or more, the structural features of the Cordil-leran mountain system of western United States have presented some most interesting problems. Any geologist or engineer living in this region, or even making occasional examinations of the mines, will lose much of interest and importance if he is not familiar with the literature. Some of the greatest works on geology have been the result of studies carried on in sections of this region. Among the more important of the earlier works are those of Dutton,l King,2 Gilbert3 and Powell;4 of the more recent Lindgren,5 Ransome,6 Spurr,7 Butler8 and others have contributed much. Many of the papers are largely of scientific interest but even these lay the foundation for the commercial application of the broader features of the geology. I have read many of these works with the keenest interest and pleasure; in fact, some have been read until some of the more important findings seem to be my own. In this paper, however, it is my aim to accept credit for little more than the labor of assembling some of the ideas of others. This is done with the hope that an interesting and valuable discussion will be the result. If some of the ideas presented should

Jan 1, 1927