Search Documents

By J. W. Snavely

A practical mathematical treatment is presented for the determination and control of conveyor belt acceleration, particularly for conditions of starting where vertical curves are involved. A typical sample problem is analyzed, with required calculations, to clarify the procedure. THE part that acceleration plays in starting a belt conveyor and its effect on belt conveyor design are well understood in a general way. Its practical importance is easily overlooked, however, and under some conditions, it is absolutely necessary to give the problem of acceleration detailed study. Most handbooks on conveyor belting design adequately present basic data for the determination of acceleration values. This paper will only attempt to present practical thinking and a convenient method of treatment of acceleration in belt conveyor design. Mathematical Analysis In working out the various problems of conveyor belt acceleration, the starting point, as presented by the handbooks, is the familiar formula of "force of acceleration is equal to the mass times acceleration." By expressing these fundamental quantities in terms of belt conveyor design, it is possible to arrive at the unsuspected conclusion that the acceleration time for horizontal belt conveyors is independent of the load, and instead, dependent upon the belt speed, the type of drive arrangement and drive pulley, and the idler coefficient of friction. The mathematics leading to this conclusion are shown in Table I, which has been prepared to show this derivation. While at first the conclusion just given may not seem to be reasonable, further reflection indicates that obviously the type of drive pulley and the type of drive do affect materially the tension in the conveyor belt, and thus, as clearly shown, the time of acceleration is dependent upon the factors mentioned. Inasmuch as all of the factors except time are predetermined by the belt conveyor design, it becomes relatively easy to establish the accelerating time and to reduce further this time determination to a simple graph from which the time in seconds can be read directly. Such a graph is given in Fig. 1. The table appearing on Fig. 1 should be explained further. For a given belt speed, the time of acceleration can be expressed as a percentage of the belt speed. The time of acceleration is also dependent on the drive arrangement, and changes in the drive arrangement consequently change the time of acceleration. It further follows that for a given belt speed, the time expressed as a percentage of that belt speed also changes with the type of drive. Obviously then, it becomes possible to graph the percentage of speed for .each type of drive against the belt speed and accelerating time, after which, for a given belt speed and type of drive, the time can be read directly in seconds. Two constants were established for Fig. 1, the first one being the limiting of the maximum acceleration tension to 35 pct of the full load operating tension in the belt. The purpose of this is to limit the total tension imposed upon the belt during the acceleration period to 135 pct of the full load operating tension, 'which is the amount required to start or breakaway the fully loaded belt conveyor from rest. The other constant is the friction factor used for the idler equipment, which has been established as 0.022. For installations where it is necessary to establish the values of acceleration, invariably high grade idler equipment is used, and it has been established from field experience that 0.022 for the idler friction factor is amply conservative. The use of this friction factor for idlers must be tempered with judgment, of course, for occasions will arise where more power than indicated is required to start, even with the very best of equipment, such as low temperature operations that tend to congeal the grease in the bearings and thus produce additional friction drag. An inspection of the table in Fig. 1 affords a convenient rule of thumb method for determining the acceleration time, which conveniently can be 5 pct of the belt speed in seconds. The 5 pct of belt speed figure is close to the average for most types of drives. In using Fig. 1 it must be emphasized that it applies accurately to horizontal belt conveyors only.

Jan 1, 1953

By J. W. Snavely

A practical mathematical treatment is presented for the determination and control of conveyor belt acceleration, particularly for conditions of starting where vertical curves are involved. A typical sample problem is analyzed, with required calculations, to clarify the procedure. THE part that acceleration plays in starting a belt conveyor and its effect on belt conveyor design are well understood in a general way. Its practical importance is easily overlooked, however, and under some conditions, it is absolutely necessary to give the problem of acceleration detailed study. Most handbooks on conveyor belting design adequately present basic data for the determination of acceleration values. This paper will only attempt to present practical thinking and a convenient method of treatment of acceleration in belt conveyor design. Mathematical Analysis In working out the various problems of conveyor belt acceleration, the starting point, as presented by the handbooks, is the familiar formula of "force of acceleration is equal to the mass times acceleration." By expressing these fundamental quantities in terms of belt conveyor design, it is possible to arrive at the unsuspected conclusion that the acceleration time for horizontal belt conveyors is independent of the load, and instead, dependent upon the belt speed, the type of drive arrangement and drive pulley, and the idler coefficient of friction. The mathematics leading to this conclusion are shown in Table I, which has been prepared to show this derivation. While at first the conclusion just given may not seem to be reasonable, further reflection indicates that obviously the type of drive pulley and the type of drive do affect materially the tension in the conveyor belt, and thus, as clearly shown, the time of acceleration is dependent upon the factors mentioned. Inasmuch as all of the factors except time are predetermined by the belt conveyor design, it becomes relatively easy to establish the accelerating time and to reduce further this time determination to a simple graph from which the time in seconds can be read directly. Such a graph is given in Fig. 1. The table appearing on Fig. 1 should be explained further. For a given belt speed, the time of acceleration can be expressed as a percentage of the belt speed. The time of acceleration is also dependent on the drive arrangement, and changes in the drive arrangement consequently change the time of acceleration. It further follows that for a given belt speed, the time expressed as a percentage of that belt speed also changes with the type of drive. Obviously then, it becomes possible to graph the percentage of speed for .each type of drive against the belt speed and accelerating time, after which, for a given belt speed and type of drive, the time can be read directly in seconds. Two constants were established for Fig. 1, the first one being the limiting of the maximum acceleration tension to 35 pct of the full load operating tension in the belt. The purpose of this is to limit the total tension imposed upon the belt during the acceleration period to 135 pct of the full load operating tension, 'which is the amount required to start or breakaway the fully loaded belt conveyor from rest. The other constant is the friction factor used for the idler equipment, which has been established as 0.022. For installations where it is necessary to establish the values of acceleration, invariably high grade idler equipment is used, and it has been established from field experience that 0.022 for the idler friction factor is amply conservative. The use of this friction factor for idlers must be tempered with judgment, of course, for occasions will arise where more power than indicated is required to start, even with the very best of equipment, such as low temperature operations that tend to congeal the grease in the bearings and thus produce additional friction drag. An inspection of the table in Fig. 1 affords a convenient rule of thumb method for determining the acceleration time, which conveniently can be 5 pct of the belt speed in seconds. The 5 pct of belt speed figure is close to the average for most types of drives. In using Fig. 1 it must be emphasized that it applies accurately to horizontal belt conveyors only.

Jan 1, 1953

By H. M. Strong

Nickel and carbon form a metastable nickel-nickel carbide eutectic system which was ohsen)able by freezing latent-heat arvests at pressures 210 khars. The eutectic freezing temperature Is pressure had a slope of -0.9°Cper kbar. At 50 khars, the nickel-nickel carbide eutectic was at 1297° * 5°C and 0.34 mole fraction Ni3C. The composition of the eutectic increased at an initial rate of 0.004 mol fraction per kbar. The carbon content of the a phase also increased with pressure. Seveval illustrations of nickel carbide microstruc-tures are given and data on the lattice expansion of nickel in terms of carbon content are included. IRON, cobalt, and nickel form a variety of carbides with compositions varying between MeC and MC. Of the three, the carbides of iron are most easily recovered. The nickel carbides are so unstable at temperatures above 900°C that their occurrence in Ni-C alloys is unusual. Under sufficient pressure, however, the temperature range for the stability of the ferrous metal carbides is likely to be increased, or their decomposition suppressed (e.g., see Hilliard' on FesC), providing an opportunity to study the unstable carbides more closely. This was found to be true for nickel carbide which, under pressure, formed a eutectic with nickel. This paper describes the conditions of formation of nickel-nickel carbide eutectic compositions and their subsequent recovery. Despite the comparative instability of the nickel carbides, something is already known about them through various chemical reactions at temperatures not exceeding a few hundred degrees, and from their recovery by the very rapid quenching of molten Ni-C alloys from temperatures of about 1450°C or above. At least four carbides of nickel have been reported: A discussion of the state of knowledge about Ni3C is given by ansen.' The studies of Morrogh and williams7 who obtained Widmanstatten nickel carbide structures and of sidorenko8 who first obtained nickel carbide eutectic structures are also of interest. Sidorenko used short heating times for molten nickel in a graphite crucible followed by very rapid quenching to obtain the eutectic structures. Long heating times produced only the nickel-graphite eutectic probably due to the presence of graphite crystals in the melt which nucleated graphite crystallization. According to the early work summarized by anssen,' nickel carbide may form at temperatures far above the melting point and may be recovered by very rapid quenching. More recently, Giardini and Tydings, working on diamond synthesis, found evidence for "free nickel carbide'' in high-pressure reactions carried to temperatures far in excess of the limit for diamond growth, followed by rapid thermal quench. They stated that nickel carbide was not found in association with diamond growth. In the present work, observations were made on the melting and solidification temperatures of Ni-C alloys as a function of composition, temperature, and pressure. The nickel-nickel carbide eutectic was found at pressures above 10 kbar and its variation with pressure followed up to 60 kbar. Nickel-nickel carbide microstructures were recovered by quenching under pressure from temperatures of about 1400°C and higher. The formation of nickel carbide structures under ordinary diamond-growing conditions was usually observed but the role of carbide formation as an intermediate step in diamond growth needs more study. EXPERIMENTAL METHODS The melting and solidification temperatures of various nickel-graphite compositions were observed by latent-heat arrests in the sample holder illustrated in Fig. 1. The samples were composed of mixtures of carbonyl nickel powder and National Carbon Co.'s SP-1 graphite packed to densities of about 6.4 g per cu cm. They were contained within

Jan 1, 1965

No records have been found of coal in the old Spanish documents, although some mention of it probably exists in manuscripts. Coal was found in Mt. Diablo, in Contra Costa County, about five miles south of the San Joaquin River in 1852, but the first mine, the Teutonia, was located in 1858. The deposits are located on both sides of a high ridge, and vessels of 1,000 tons burden could ascend the river to the nearest point to the mines.1 In 1854, coal was found about four miles from Oroville, on the Feather River, in Butte County. Development work was started and in 1856 a mine was opened. From the description the coal was likely a variety of lignite and probably never amounted to anything commercially, as it does not appear again in the records 2 The more valuable mines at Mt. Diablo were opened in 1859 and 1860. By 1867 there had been 11 mines started and at that time five were in operation. The seam conditions were much disturbed and lack of knowledge of them caused much waste of effort and money. All of the coal excepting that used locally and in nearby towns, was shipped to San Francisco, and largely used for steam purposes. The first receipts were in 1861-6,620 tons. A railroad to the river had been constructed and opened in February 1866. The Corral Hollow field in Alameda County was found and prospected to a small extent in 1862. Two mines were opened but little work was done and the field was then abandoned. Good exposures were rare and the cost of underground exploration was then prohibitive. The Commercial mine produced coal in 1869 and 1870, but a fire in the latter year destroyed the tipple and communications to the mine. The Livermore mine was abandoned after 18 months operation in 1875 and 1876 and no other work was done here until the nineties. In 1867 Hyne reported the presence of coal in workable thickness, and of good quality, on the property of the Pacific Coast Petroleum Company,

Jan 1, 1942

By Ulf S. Landergren

Diffusion coefficients and marker movements have been determined in brass using welded couples. Three different concentration ranges were employed at 750°C, while a fourth concentration range was measured at 500°, 600°, 700°, and 800°C. Marker displacements toward and porosity development in the high zinc side of the couple were observed in all cases. The results were interpreted as favoring a vacancy diffusion mechanism. IN the large amount of diffusion literature which has accumulated during the past half century, very few experimental data have been presented on body-centered-cubic metallic phases. The impressive combination of experimental and theoretical studies which has given the vacancy mechanism a fairly secure position as the preferred mechanism for most face-centered-cubic metals has no counterpart for body-centered-cubic phases, although the theoretical picture seems to be in a better state than the experimental work. The attempts to select diffusion mechanisms by the theoretical calculation of the activation energy for the various conceivable unit diffusion processes and the energy of formation of the type of lattice defect required have been based on models of two kinds. The first kind utilizes potential functions fitted for certain properties of pure crystalline copper; the second kind is fitted for sodium. The latter is an example of an open metal in which the metallic ion is small compared with interatomic distance,&apos; while the former is characteristic of the larger class of metals in which the ions have diameters about as large as the interatomic distance. brass should resemble copper in this fundamental property. It should be evident that results on the mechanism of diffusion obtained for one of these classes need not necessarily apply to the other. Huntington and Seitz, using a model of the copper type, showed that the activation energies to be expected for interstitial migration or a two-atom direct interchange were much higher than that for vacancy diffusion. Zener pointed out that a four-atom ring rotation would involve an activation energy considerably lower than the two unlikely mechanisms although still higher than the vacancy mechanism in the face-centered-cubic structure. Furthermore, he argued, the four-atom rotation would be relatively easier in a body-centered-cubic lattice and might be competitive with the vacancy mechanism. Paneth showed that a body-centered-cubic crystal-like sodium could form interstitial defects of special type, called a crowdion, by crowding an extra atom into < 111 > directions where the defects would affect a line of about eight atoms. The defect was constrained to move along the defining line. Unlike the face-centered-cubic case, therefore, the theoretical calculations for the body-centered-cubic mechanism do not provide a very clear-cut answer, and the absence of adequate experimental studies is the more serious. This investigation was undertaken for the purpose of obtaining useful information on diffusion in body-centered-cubic phases. brass was chosen for several reasons: 1—the phase field is sufficiently wide at high temperatures to permit the use of diffusion couples with adequate concentration ranges for satisfactory chemical analysis, 2-—thermodynamic activity data are available for the calculation of mobilities from diffusion coefficients, 3—the phase is as close to the theoretical model of the copper -type on which the calculations have been done as any body-centered-cubic metallic phase is likely to be. Measurements of the movements (if found) of inert markers during the diffusion process would indicate that a vacancy or Or mechanism played a major role in diffusion in brass. If no marker movement should be found, a ring mechanism would be indicated but not assured. Experimental Procedure The alloys used in these experiments, listed in Table I with analyses, were supplied by the Naval Research Laboratory. They were from ingots of 3x3 in. cross-section, heated to 760°C, reduced under a

Jan 1, 1957

Henry Louis, Newcastle-upon-Tyne, England (communica, tion to the Secretary): I have been much interested in Mr. Schmitz&apos;s description of the copper-ore bed in the Permian formation of Texas. He compares it with the Mansfeld Kupferschiefer; but it seems to me to present closer analogies with a small deposit on the same side of the Atlantic, in Nova Scotia, which I examined in 1877. I quote entirely from my fieldnotes, made then, and from specimens still in my possession. These copper-deposits are known in several places; but I examined them at the village of New Annan, on the banks of the French river. This district has been determined by Sir J. W. Dawson as being of Permian age, and this determination seems to have been confirmed as recently as 1891 by the operations of the Canadian Geological Survey. The following is the section, very imperfectly exposed in a few shallow levels, described in ascending order: Red sandstone, moderately fissile and markedly false-bedded. Lower nodule-bed, 1 inch to 6 inches thick, of fissile mica, ceous sandstone, containing obscure plant-remains converted into anthracite, chalcopyrite, chalcocite and iron pyrites. Very coarse grit or, in places, red sandstone; thickness and character variable. Upper nodule-bed, 6 inches to 2 feet thick exceptionally, generally about 10 inches. Soft, gray, friable shaly sandstone, with nodules of copper-ore. Red sandstone. All these strata lie flat, in places quite horizontal, in places dipping towards the river at 5° to 10°.

Jan 1, 1897

By F. Claisse, R. Angers

Self-diffusion in iron has been measured during rapid a-r transformations using a variant of the Kryukou and Zhukhovitskii diffusion method. The study was performed by thermally cycling iron foils (1 to 6 cpm) through the transformation (=910°C). Some foils have been subjected to over 1000 cycles and some have spent more than 15 pct of their total diffusion time in the process of transformation. The experimental results show that the a-r transformation has no measurable effect on self-diffusion in iron. The study is completed by a quantitative analysis of mechanisms which can affect the diffusion rate during the transformation. The analysis confirms the experimental results. SINCE diffusion is an important factor in many solid-state transformations, it is of interest to study how it is affected by the stresses generated during these transformations. Clinard and Sherby1&apos;2 were the first to make a study along these lines. They measured diffusion coefficients in Fe-FeCoV couples subjected to slow thermal cycling (1.5 cph) through the a-r transformation range. They found an enhancement of diffusion by a factor of about two. The purpose of the present paper is to report measurements of the self-diffusion coefficient of iron during much more rapid thermal cyclings (1 to 6 cpm) through the a-r transformation (-910°C). These more rapid cyclings produce higher strain rates during the transformation and should emphasize any possible influence of transformation upon diffusion. EXPERIMENTAL Iron foils, 25 to 35 µ thick, were cold-rolled from 99.92 pct pure iron and annealed in pure helium for 2 hr at 870°C; the resulting grain diameter was about 150 µ. Specimens 0.5 by 8 cm were cut from the foils and I7e55 was vapor deposited on one of their surfaces. A 38 gage alumel-chrome1 thermocouple was spot welded in the middle of one of the specimen long edges, Fig. 1. Two 38 gage chrome1 wires were also spot welded along the same edge on each side of the thermocouple; they were placed 2.5 cm apart and used for electrical resistance measurements. In order to prevent twisting and crumpling, the specimens were pinched between two quartz plates 0.1 by 1 by 7 cm and the assembly was close fitted into a 1 cm ID quartz tube. Four holes were drilled through the tube to let the 38 gage wires out: these were connected to the recording equipment by means of extension wires. 20-gage nickel wires fixed at both ends of the specimens were used to thermally cycle the foils by Joule heating. The above described device was placed in a 2.7 cm ID quartz tube which in turn was placed in a tubular furnace. Either a pure helium atmosphere or circulating hydrogen was used during the experiments. Specimens were subjected to thermal cycles between a minimum temperature To and a maximum temperature Tm at rates ranging from 1 to 6 cpm. This was obtained by maintaining the furnace at a constant temperature near the minimum temperature To and periodically passing an electric current through the specimen. Cooling was achieved by heat losses to the surroundings. The forms and periods of cycles were varied from one specimen to another; however, each specimen was subjected to one type of cycle only. The temperature and electrical resistance variations of the specimens were recorded as a function of time. The temperature curves were used for diffusion calculations while the electrical resistance curves were used to monitor the transformation and to determine its starting point and its approximate duration. Diffusion was measured by the method developed by Kryukov and zhukhovitskii3 and modified by Angers and Claisse.4,5 In this method a metallic foil is coated on one side with a radioactive isotope and the activity is measured periodically on both sides during the diffusion anneal. The following equation then holds: where: I1 Activity on the surface on which the deposit is made. I, Activity on the opposite surface. t Diffusion time. B Constant. D Diffusion coefficient. d Foil thickness including the deposit. G(t) A function of time; it is a second order correction term which is given graphically in Refs. 4 and 5. The diffusion coefficient D is found by plotting ln[(Il - I2)/(I1 + I,)] -G(t) against t; the resulting slope m leads to an accurate calculation of D through Eq. [2]. The effect of the a-r transformation on diffusion is expressed by the ratio DT/DU where:

Jan 1, 1970

By AIME AIME

THE 1944 Chairman of the Institute of Metals Division might be classed as metallurgically ambidextrous ; he is teacher of theory and practice of both nonferrous and ferrous metallurgy, and he is consultant on brass and on highspred steel. Arthur Phillips was born in Troy N.Y. and attended the New Haven Connecticut high school. Upon graduation he entered Yale, receiving a degree in metallurgy in 1913. At that time Professor Mathewson was starting his plan of &apos;"co-operation with the metal industries in metallographic work at the Hammond Laboratory of the Sheffield Scientific School, Yale University, and Arthur Phillip, became the first co-operative graduate student, working in the laboratory of the Bridgeport Brass Co., and receiving his Masters of Science degree in 1915. A little later, when the department of metallurgy at Yale was expanded. Me. Phillips was appointed assistant professor. In 1928 he was made associate professor, and in 1934 he was promoted to full professor.

Jan 1, 1944

By G. W. Brownell, H. T. F. Lundberg, R. W. Pringle, K. I. Roulston

The rapid improvement of the airborne scintillometer and the perfection of its efficiency for counting low energy gamma radiation has made it possible to work out a technique to map in great detail the radiation pattern at the earth&apos;s surface. On such maps low radiation over certain areas appears to indicate the existence of oil accumulations, forming a pattern similar to that obtained by the geo-chemists. RADIOACTIVE analyses of samples from the surface of oil fields were carried out more than 10 years ago in Alberta by the alpha particle ioniza-tion chamber technique,&apos; but large enough tracts could not be covered in these investigations to make possible any evaluation of the method as a means of oil exploration. Considerable interest has recently been revived, however, as a result of certain striking advances which have been made in the instrumentation available -for the measurement of radioactivity. It is the object of this paper to indicate the nature of these improvements in radiation technology and then to describe the attempts that have been made to interpret the radioactive patterns obtained in the course of airborne recordings with the new instruments. Since the survey can be carried out from the air and records can be accumulated over vast areas in a short time, the result may easily lend itself to statistical treatment. Areas have been surveyed in Alberta, British Columbia, Saskatchewan, Quebec, Texas, New Mexico, Nebraska, Colorado, Utah, and Montana. Producing fields in Alberta and West Texas have been flown over several times in different directions, Fig. 1. The operations were then extended into unknown territory and drill holes were put down on the anomalies which looked promising. The results from these drillings were encouraging and have given hopes for the development of an entirely new method of oil exploration. Any large scale method for the survey of radioactive anomalies must be based on the measurement of gamma rays, as beta and alpha rays have much too short a range to be of any significance. Thus the essential improvement which has made the present stage of this work attainable is the development of new highly sensitive detectors for gamma radiation. In the past the only detectors of any consequence that were available were the ionization chamber and the geiger counter, but both of these suffer from the defect that only a small proportion of the gamma rays passing through the counter are detected, possibly 0.1 to 0.2 pct. The recent development of the scintillation counter2,3 has completely transformed the situation and has had a considerable impact on many branches of nuclear technology. The detection of alpha particles in zinc sulphide screens by visual observation of the individual scintillations which these particles produce dates back to the early spinthariscope of Rutherford and Crookes, but the combined use of an appropriate scintillating phosphor and photomultiplier tube had to await the technical development of the latter many years later. With this development came the modern era of the scintillation counter and a knowledge of phosphors which have a large light output under the bombarding action of gamma radiation. Some of these phosphors are relatively dense and are capable of stopping a large proportion of the incident gamma radiation. As the sensitive region is the whole volume of the crystal, a very high detection efficiency, 50 pct or more, can be obtained for medium energy gamma rays. Scintillation counters for geological purposes were first developed in 19494-6 in an attempt to utilize this remarkable improvement in efficiency, which has the attractive consequence that only a small portion of the normal background of the counter is due to cosmic radiation. In 1949 tests were made in northern Saskatchewan by Lundberg Explorations Ltd. with portable scintillation counters which gave excellent results in the search for uranium and served to indicate unknown uranium deposits in areas previously closely surveyed with geiger counters. Portable scintillometers (registered in Canada) are now commercially available and in regular use,&apos; and the adaptation of the instrument to radioactivity oil well logging has also been very successful.8 Initial attempts to measure radioactivity from aircraft with scintillation counters were made during this period in the same area and yielded most encouraging results. It would be appropriate to consider some specific requirements for airborne investigations. The essential problem to be met in the detection of any radioactive source is the necessity of obtaining a signal greater than the statistical fluctuations of the background counting rate for the instrument. It is possible to show that Nt>2k2 is the condition for detectability of a signal where N = average background counting rate for the detection. t = time constant of the counting rate meter, used to determine the average number of counts arriving in a certain predetermined time interval. N&apos; = average source counting rate at the detector. k = N/N&apos;, and N>>N&apos;. Sample values are given in Table I. Assume that the aircraft carrying the equipment is travelling at 120 mph, in which case it will cover 176 ft in 1 sec. Assume also, as a first approximation, that a point source target is in range when the air-

Jan 1, 1954

"The power development at these falls, three miles below the city of Great Falls, was made in 1891 by the original Great Falls Water Power & Townsite Company, and the Boston & Montana Consolidated Copper & Silver Mining company, the predecessor of the Boston & Montana Reduction Department mentioned above.The dam is 746 feet long, placed a short distance above the crest of the falls, and giving an effective head, as now constructed, of from 42 to 44 feet. There are power houses on both banks, those on the south bank belong to the Great Falls Power company, the successor of the Great Falls \!\Tater Power & Townsite Company, and the Great Falls Electric properties. The water is led from the dam to these power houses through sheet iron pen-stocks the water wheels are of the horizontal turbine type, and of various sizes.The water is here carried from the dam to the power houses by an open canal or headrace, the walls of which are concrete. This headrace is 100 feet wide at the widest point. The available head was originally less than 40 feet, but this was increased to about 44 feet by means of flashboards and tailrace wall, seperating the tailrace from the main river and delivering the water to the river at a considerable distance below the power house, thus taking advantage of a considerable fall in the river below the sheer fall at Black Eagle.A total of about 12,000 horse power 1s developed at these falls, the Great Falls Power Company, and Great Falls Electric properties developing about 2,000 horse power, and the Anaconda Copper Mining Company developing the balance."

Jan 1, 1913

By Gerard C. Gambs

The electric utility industry is the largest customer of the U.S. coal industry, consuming nearly 50% of present coal production. By 1980, the electric utilities are expected to burn over 500 million tpy of coal or 75% of total coal production. When coal is burned in electric utility plants, ash is produced in one of several forms. These include fly ash, bottom ash and bottom slag. At the present time, approximately 20 million tons of these ashes are produced and must be disposed of by the utilities at a cost of 50[c] to $2 per ton. In 15 years, more than double this quantity will be produced. Only a small quantity of this ash is put to any practical use. Much remains to be done about expanding uses for fly ash and bottom slag.

Jan 1, 1967

By A. S. Malicsi, I. Iwasaki

The removal of hydrophobic coatings of flotation collectors from iron ores becomes of interest when a duplex flotation process is considered for upgrading, when a pelletizing process is considered for a concentrate floated with a fatty acid or a soap collector, or when a disposal of froth products from cationic silica flotation is of environmental concern. Ozone can oxidize organic compounds rapidly, thereby removing the hydrophobic coatings of flotation collectors. Ozone is widely used for treating and purifying drinking water, waste water treatment, and for chemicals processing (Murphy and Orr, 1975; Rice et al., 1980). Its uses in metallurgical operations, however, are very sparse (Allegrini et al., 1970; Chernobrov and Rozinoyer, 1975; Ishii et al., 1970; Iwasaki and Malicsi, 1985; Matsubara et al., 1978). Yet, its high reactivity and the absence of potentially hazardous byproducts become of interest in destroying flotation reagents adsorbed on mineral surfaces or remaining in mill water for recycle or for discharge. Duplex Flotation A duplex flotation process, as applied to oxidized iron ores, would involve a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process has been used in the Florida phosphate fields. Fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates. A combination of reagents, such as lime and quebracho, lime and alkali phosphate, or sulfuric acid and oxalic acid, has therefore been proposed. In a previous article (Iwasaki et al., 1967) , the use of activated carbon was found to be effective in removing fatty acid coatings both in the duplex flotation and the pelletizing processes. The use of ozone offers another approach to the removal of fatty acid coatings from iron oxide surfaces. To investigate the possible application of the duplex flotation process, a specularite ore from Michigan analyzing 36.5% iron was used. A 600-g (1.3-1b) sample was ground in a laboratory rod mill together with 250 g/t (0.5 lb per st) of sodium silicate to -150 µm (-100 mesh). This was transferred to a Fagergren laboratory flotation cell, and deslimed four times at 20 µm (quartz equivalent). The deslimed pulp was transferred to a laboratory conditioner, diluted to 40% solids, and conditioned with 250 g/t (0.5 lb per st) of soda ash and 250 g/t (0.5 lb per st) of oleic acid. The conditioned pulp was then transferred back to the Fagergren cell, floated until barren of froth, and the rougher froth product was returned to the cell and cleaned. The results are presented in Table 1. The cleaner concentrate at this point analyzed 45.3% Fe. The cleaner concentrate coated with fatty acid was transferred to a 2-L (0.53-gal) beaker. While the pulp was agitated with a glass T-stirrer, ozone was bubbled into the agitated pulp for 15 minutes at a rate of 10 mg/min (0.00035 oz per min) ozone (250 g/t or 0.5 lb per st 03 feed). It was observed that the pulp ceased to froth after about 10 minutes. The amine flotation of siliceous gangue from the ozonated pulp was carried out first by conditioning with a dextrin, a commonly used starch depressant for iron oxides. This was followed by flotation with a stage addition of an ether amine at increments of 100 g/t (0.2 lb per st). Three stages were required to float the siliceous gangue to near completion. The three froth products were combined and cleaned twice. When the cationic flotation Rougher, Cleaner 1 and Cleaner 2 cell products were combined, an iron concentrate analyzing 64.5% iron was obtained at an overall iron recovery of 72.8%. Pelletizing Fatty acid flotation concentrates have been pelletized successfully in northern Michigan mills. But at other locations, fatty acid coatings on iron flotation concentrates proved so undesirable in agglomeration that other methods of concentration had to be sought. For example, a sinter mix containing iron ore concentrates upgraded by fatty acid flotation resulted in decreased productivity. This occurred because the micropellets of particles with the hydrophobic coating are less tolerant of moisture. Thus, the bed permeability is lost (Beebe, 1965). The agglomeration of concentrates obtained by the fatty acid flotation alone, and the hydrophobic coatings destroyed by ozonation or by the duplex flotation process, is not expected to cause any difficulty since the surfaces of the concentrates would be hydrophilic. Removal of the fatty acid coating with activated carbon, indicated by the loss of floatability, was shown to restore the decrepitation temperature of wet balls during drying cycle (Iwasaki et al., 1967). Disposal of Cationic Silica Flotation Froths Recent demands of iron blast furnaces place the silica content of the magnetic taconite pellets at about 5%. Conventional process for magnetic taconite involving fine grinding and magnetic separation often produces magnetic concentrates analyzing in excess of 5% silica. This is due to the presence of the middling grains of siliceous gangue and magnetite. Cationic silica flotation of magnetic taconite concentrates (DeVaney, 1949) may be used to reduce the silica content. But the amine coating on siliceous gangue becomes of environmental concern when the flotation tailings are discarded in tailing ponds.

Jan 1, 1986

Francis Drake, Bulawayo, Rhodesia, So. Africa (communication to the Secretary *):—I should like to place on record some data in addition to those given by Mr. Canby in his paper. I regret that my notes have been destroyed so that I can give no accurate measurements of the water jacket that I am about to describe. This furnace mas erected in Cerro Gordo, Inyo county, Cal., early in 1875, and I think it quite possible that it was the first applied in lead smelting. It was made of plate iron and elliptic in shape, the inner dimensions being about 54 by 42 in. by 48 in. high. The distance between the inner and outer plates was about 6 in. Tuyere holes, one at the back and two on each side, about 12 in. in diameter, were made in this, and in these were placed cast-iron water tuyeres about 16 in. long, the diameter of the blast orifice at the point being about 3 in. The height from tuyeres to feed door was about 9 ft., but the top of the charge was kept about 5 ft. above the tuyeres. There was a space of about 12 in. between the jacket and the top brick-work. This brick-work was supported by a cast-iron plate resting on four cast-iron columns. At the beginning, the jacket was lined with air-dried radial bricks, made of crushed quartz and fire-clay, as it was thought that the jacket would not stand the heat on its bare plates. After a short time the practice was altered and no lining mas put in. The jacket was closed at the top and had a steam drum connected by two pipes at the back. This steam drum was connected to the boiler in which the steam was made for driving the Baker blower, the rock breaker and the pumps. The bottom of the jacket mas also connected to the boiler. The jacket was run under boiler pressure (80 Ib.) for some time, but eventually cracks developed in the inner plate between the tuyere holes,

Jan 1, 1913

By D. A. Stevenson, R. A. Burmeister

Single-phase silver antimony telluride has been prepared by zone-melting techniques using initial compositions of A new phase appears upon prolonged annealing of this material, but the reaction does not appear to be a simple eutectoid decomposition. A complete analysis of the phase equilibria is complicated by the slow kinetics involved. The Hall coefficient, magneto -resistance, electrical resistivity, and Seebeck coefficient are all sensitive to the presence of second phases. The low Hall mobilities measured for single-phase material indicate that the usual band theory is inadequate to explain the observed transport properties in the system. Density anomalies of up to 2.5 pet between measured and theoretical density were observed but are not conclusive evidence for a defect structure. COMPOSITIONS in the Ag-Sb-Te system have been studied previously by several investigators.1"18 The interest in this system arises from potential thermoelectric applications of alloys on the Ag2Te-Sb2Tes vertical section. Although the composition corresponding to the formula AgSbTe, has received most attention, it has been found to consist of more than one phase.7&apos;8 A thorough understanding of the properties of this heterogeneous material has been impeded by both lack of knowledge of the properties of the homogeneous phases comprising it and the problem of analysis of transport properties in an inhomogeneous system. The present work describes the preparation of the homogeneous ternary phase and the corresponding electrical properties of both homogeneous and heterogeneous material. MATERIAL PREPARATION Most specimens for this investigation were prepared by encapsulating the elements in evacuated quartz tubes after which they were melted and homogenized in the liquid state. The ambient temperature was then dropped to 500°C and the resulting ingot zone melted. The growth rate, width of zone, stoichiometry, and number of passes have an effect on the resultant microstructure. Grains several centimeters in length were easily produced by this method. Other solidification techniques were also used, including uniform slow cooling of the entire specimen and rapid freezing. The microstructures of specimens produced by these techniques frequently differed appreciably from similar compositions prepared by zoning. A variety of nonequilibrium microstructures characterized by long needlelike particles resulted from the rapid-freeze method. PHASE EQUILIBRIA The lack of information on phase equilibria is a major difficulty associated with a comprehensive study of the Ag-Sb-Te system. Considerable confusion has resulted from the use of the formula AgSbTe, to identify the cubic ternary intermediate phase even though it has been established that material of this stoichiometry normally contains AgzTe as a second phase.798 In this paper, silver antimony telluride will denote the cubic ternary intermediate phase comprising the major portion of AgSbTe,. The term "single phase" will denote material which consists of only the cubic phase (as evidenced by metallographic examination and X-ray diffraction) and the term heterogeneous will describe multiphase material containing AgzTe, SbzTe3, or other phases in addition to the cubic phase. The single-phase material may actually contain a variety of inhomogeneities—gradual changes in composition on a macroscopic scale, localized fluctuations in composition, clusters or other products of early stages of the precipitation process, and a variety of point and line defects—all of which will not be detected by the present techniques for determining homogeneity. Single-phase material has been prepared from compositions close to 59 mole pct SbzTe3 21 (this notation refers to the location on the Ag,Te-Sb2TeS vertical section). Zone widths of =2 cm and growth rates 51.2 cm per hr were used. The single-phase region at elevated temperatures extends off the vertical section to a composition which can be expressed approximately as Ag,,SbzgTes,.9 The latter two compositions as well as AgSbTe, are represented in the conventional Gibbs triangle in Fig. 1. It is not presently possible to ascribe exact values to the limits of the single-phase region on a given isotherm or vertical section due to the extremely

Jan 1, 1964

By P. Ramachandrarao, T. R. Anantharaman

EVER since the technique of quenching metals and alloys from the melt (splat cooling) was perfected a decade ago, it has been recognized that the grain size of products solidified by this technique may be extremely small.&apos; The further observation that fcc metals quenched from the liquid state contain very few dislocations has led to the inference2 that metals are subjected to negligible or no stresses during the rapid solidification characteristic of the "gun" or "piston-and-anvil" technique. Evidence for the incidence of appreciable densities of stacking faults has, however, been obtained in case of some splat-cooled fcc and hcp alloys,3 although not for pure metals. In the light of these earlier observations it was considered desirable to study X-ray line-broadening effects, if any, in fcc metals rapidly cooled from the melt. In the present work pure silver (>99.99 pct), aluminum (>99.99 pct) and lead (>99.9 pct) were quenched from the liquid state from temperatures about 50°C above the melting point by the "gun technique" and the resulting foils were subjected to X-ray examination in a Philips Diffractometer. The quenched foils (up to -10 u thick) did not generally stick to the substrate surface and could be easily transferred to the Diffractometer without introducing any plastic deformation. The profiles of the first five reflections from the foils were recorded in each case with Cu Ka, radiation at the slowest available scanning speed of 1/8 deg per min. To correct for instrumental broadening, profiles were also recorded from the metals annealed in vacuo at suitable temperatures. The integral breadths of the X-ray reflections were arrived at by a procedure described earlier.&apos; There was a distinct suggestion of preferred orientation in the recorded intensities of reflections from aluminum and lead foils. Such an effect was not observed in case of silver. In addition, the integral breadths of X-ray reflections from splat-cooled aluminum and lead were not significantly different from those recorded for the annealed metals. The analysis was therefore continued only for silver where the X-ray line broadening was appreciable. The pure diffraction broadening, B, was evaluated for each X-ray reflection (hkl) from silver from the observed, B, and instrumental, b, breadths with the aid of each of the three equations due to Scherrer,5 Anantharaman and Christian,6 and Warren and Biscoe,7 respectively: Bs= B-b BAC=B- b2/B Table I gives the values of particle size, 71, the lattice strain, E, arrived at by the use of the following well-known relations and on the assumption that all observed diffraction broadening could be attributed to lattice strain or particle size, respectively: E = 1/4 cos ? n= B cos ? where A is the wavelength of X-radiation and 0 is the Bragg angle. As no significant peak shifts or asymmetry could be detected in the profiles from the foils, the possibility of any significant contribution due to twins or stacking faults was ruled out. The absence of faults is by no means surprising since pure silver is known to develop stacking faults only on severe deformation and the stacking fault densities recorded so far for even silver filings have been extremely low.&apos; The very low values for percentage mean deviation from the mean value for the particle size in Table I strongly suggest that all observed broadening in splat-cooled silver can be attributed only to small particle size. This conclusion receives further support from the lowest mean deviation recorded for data computed from the Scherrer equation based on Cauchy profiles that are considered characteristic of particle size broadening. Further analysis for separation of particle size and lattice strain effects was considered unnecessary in view of the very large mean deviations obtained for strain values and also the earlier results suggesting absence of even detectable strain in metals and alloys quenched from the melt. It is to be stressed in this connection that the particles are actually grains and not cells formed by walls of high dislocation density usually encountered in deformed samples. As such, the absence of strains is not surprising. The present results are probably the first to record X-ray line broadening due only to small particle

Jan 1, 1970

By J. W. Snavely

THE high tension belt conveyor is introducing a new and tremendously expanded era of low cost bulk material handling. High tension belt conveyors are generally those installations involving very long centers, high lifts, or drops, in which the belts are stressed up to their maximum tension values, and further, where the belt construction provides tension capacity far beyond what is possible with conventional belt constructions. With these high tension installations, the magnitude of the forces involved demands careful refinement of accepted design practice in order to achieve optimum balance of all factors. No attempt will be made to evaluate the relative merits of belt conveyor haulage with other means of transportation. For present purposes, it is assumed this has already been done in favor of belt conveyor. Neither will any attempt be made to evaluate the various conveyor belt constructions now available or to balance the advantages of various types of mechanical equipment. It is also assumed that the basic haulage information on which the conveyor design is based is accurate and complete. A sustained maximum, uniform load on the belt at all times must be achieved through proper feed control and the use of adequate surge storage to level the peaks and valleys of any varying demand for the material being handled. General Belt Capacity Considerations The belt conveyor capacity tables published by various belting and conveyor equipment manufacturers vary to a considerable degree, and the ratings given are quite conservative. Of necessity, these published ratings are based on the handling of average materials under average conditions. In applying a high tension belt, all possible capacity from the belt must be obtained in order to hold its width to a minimum and thereby limit the initial cost. Two factors are involved, loading to maximum cross section area and traveling at a maximum practical speed. Belt Loading: Proper treatment of the loading of the belt will result in maximum cross section to the load, and published capacity ratings can be exceeded, sometimes by appreciable margins. On the 10-mile conveyor haul used in the construction of Shasta Dam, California, although the rated capacity of the belt line was 1100 tons per hr, at times the system handled peak loads of 1400 tons per hr, almost 25 pct better than the rated capacity. One of the large coal companies has been able to exceed rated capacity by as much as 50 pct. Loading conditions which must be controlled are: 1. Large lumps must be scalped off and rejected or the load must be primary crushed before being placed on the belt. 2. The material weight per cubic foot must be accurate, must be known for all the materials being handled, and must be known for the complete range of conditions of the individual material being handled. Long centers and high lifts magnify small differences into serious proportions. 3. Uniform feeding to the belt is most important. Various types of feeders are available, which can be used to place a constant predetermined volume of material on the belt, or, where an appreciable range of material weight exists, through electrical control actuated by current demand, to place a predetermined uniform tonnage on the belt. One long slope belt in a coal mine in Pennsylvania is being fed at three separate stations with the controls so arranged that whenever the maximum load is going onto the belt from the first station, the other two stations automatically cut out. Whenever the load from the first station drops back, the other two stations again automatically cut in. 4. Careful design of the chutes and skirts is necessary to get the load centered on the belt with a minimum of free margin along each edge. Some free margin at the edge of the belt is necessary to prevent spillage, but if the load can be kept accurately centered, this free margin area can be reduced, and more material can be carried on the belt. What can be accomplished in this respect will vary widely, depending on the nature of the material being hauled. The chute and skirt design must also protect the belt. 5. The design of chutes and skirts should also get the load traveling in the same direction and close to belt speed, so that the load comes to rest on the belt as quickly as possible. The design of the chutes and skirts is worthy of careful study, and after a system is put into operation it should be experimented with to get the best results. Belt Speed: High belt speeds should be used in high tension work. Obviously, high belt speeds enable haulage on a narrower belt, reducing initial cost. The major portion of belt wear takes place at the loading point and around the terminal pulleys. The

Jan 1, 1952

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials; it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted.

Jan 3, 1918

By W. Hodge, A. F. Haskins, R. M. Evans

Refractory boron compounds are shown to resist corrosion by molten zinc. Coatings were made from ferroboron and manganese boron by several methods: welding, hard facing, and pack diffusion; and techniques of coatings are very important. Mechanical failure of the diffusion coatings can be partially eliminated by applying them to type 416 chromium steels rather than carbon steels. Welded coatings made with a tungsten arc are better than those made by other welding methods. Sintered compacts of mixtures of iron and chromium borides developed strengths of about 30,000 psi. They resisted corrosion of zinc at 600°C and oxidation at higher temperatures. MOLTEN zinc rapidly attacks common metals of construction. The rate of attack is greatly amplified at temperatures over 500°C. However, there are many applications where it is necessary, or at least advantageous, to use metal construction, such as for galvanizing pots and zinc smelter equipment. Condensers and agitator linings used in continuous zinc smelting processes are eroded and corroded by violently agitated molten zinc. Pumps, tubing, and other parts to permit transfer of molten zinc would be desirable in many zinc handling operations. The development of metallic materials which are resistant to molten zinc also might permit its use as a heat-transfer medium in modern high efficiency power plants. In reviewing previous work on zinc-resistant metals, it was evident that most of the available data refer to corrosion at temperatures just above the melting point. Tungsten and high Mo-Fe alloys containing more than 80 pct Mo resist corrosion by molten zinc.&apos;, &apos; Imhoff states that because chromium is not attacked by zinc, chromium plating improves galvanizing pot life." Nitrided cast iron has been used in die-casting machines&apos; where the molten alloy is 96 pct Zn and 4 pct Al. Other metals that have been suggested as of possible value for zinc resistance are columbium, tantalum, and titanium.V he corrosion of steel by zinc has been discussed by many authors,z, "2 None of these materials resisted corrosion by molten zinc at the temperatures used in this investigation, i.e., 600" to 700°C. I. Exploratory and Resistant-Coating Tests To make a study of zinc-resistant metals, exploratory tests were conducted to sort out roughly those materials which seemed most worthy of further development. This preliminary study included both solid metals and surface coatings. Exploratory Corrosion Tests in Molten Zinc—In initiating a study of this problem, numerous samples of metals and alloys were evaluated by dynamic corrosion tests made at 440 °C. Each metal was tested in its most readily available form, which, because of shape and size, was often unsuited for standard corrosion testing. The equipment used for dynamic corrosion testing of all materials, except in a few initial experiments, is shown in Fig. 1. Samples were tied to tungsten rods with tungsten wire, immersed in the zinc, and revolved at 12 rpm about the circumference of a 4 in. diam circle. Speed of travel was about 12.5 fpm. The molten zinc was protected from oxidation by an atmosphere of carbon monoxide, or, at a later period in the program, by a 9:1 mixture of nitrogen and hydrogen. When the effect of both molten metal and atmosphere was desired, the zinc level was lowered. Special high grade zinc was used in all of the corrosion tests. Corrosion losses for materials tested are shown in Tables I and 11. Whenever the materials were available in suitable form, the losses are reported in mils per year. It was recognized that weight losses on irregularly shaped specimens did not show the corrosion rate but the important consideration—poor resistance to corrosion—could be determined readily.

Jan 1, 1956

By Ralph Arnold

WHILE much geological work and drilling have been done in Venezuela, the incompleteness of geological evidence obtainable and the restricted areas in which drilling has been done make any estimates of oil resources extremely speculative. Nevertheless, it is felt that the data given are justified, in the belief that the ideas of a geologist familiar with the region are better than those of a promoter. The oldest beds of interest to oil men are those of the Cretaceous, which are well developed in eastern Venezuela and about parts of Lake Maracaibo. In both cases, a hard massive limestone is overlain by a great thickness, most of which is shale. In the west, in places this shale is more than 2000 ft. (610 m.) thick, while in the east it may attain 3500 ft., (1067 m.). The limestone and parts of the shale are oil producing. In the east, the Tertiary where present is almost entirely covered by the Quarternary, but in the west it is well developed. In probable unconformity over the Cretaceous shales is found a series of sandstones and shales, which may beg called the lower coal series. It is well developed southwest of the lake, where it is the oil container, and is probably the lowest series exposed east of the lake. Above this is the Pauji shale, which is probably the point of origin of all the oil east of Lake Maracaibo and in the State of Falcon. It has a thickness of about 3000 ft. (914 m.) in the Mene Grande region. The upper coal series is developed as a great thickness of sands, shales, and clays, with some partly consolidated limestone. Its thickness may be as great as 10,000 ft. It is the oil container of the Falcon-El Mene region and a probable location for oil in some of the area about the lake. It may or may not include the so-called Maracaibo series in which the oil is found at Mene Grande. Over much of Venenzuela, the Quarternary is present in unknown thickness, which probably is not great. It obscures oil structure in all cases and presents the greatest hazard of oil exploration for the fields which probably exist below.

Jan 7, 1922

By S. J. McCarroll

J. Bruce Clemmer, J. B. Rosenbaum, and C. H. Schack (U.S. Bureau of Mines, Salt Lake City)—We have watched with considerable interest Three Kids development of Manganese Inc. and have been impressed by the ingenuity with which management and staff have solved their many obstinate handling problems. Mr. McCarroll has been lenient in describing the difficulties faced by the company in developing a process for beneficiating Three Kids ore. The operation, equivalent in size to a 20,000-ton sulphide ore plant, is treating a unique ore by a flotation process pioneered by Manganese Inc. Perhaps the magnitude of the conditioning and flotation problems peculiar to Three Kids ore can be better appraised when it is pointed out that two-thirds to three-fourths of the ore is floated in the rougher step and that the four stages of cleaning which follow are equivalent to floating the whole plant feed two to three times. Our experience in both laboratory and pilot plant flotation of Three Kids and other manganese ores leads us to agree with Mr. McCarroll that suitable conditioning is a prime requisite for successful oil-emulsion flotation. The difficulties of proper conditioning were demonstrated in pilot plant processing of Artillery Peak manganese ore at our Boulder City, Nev., experiment station. Over three months of experiments and extensive plant revision were required before satisfactory conditioning was obtained in the 25-ton-per-day plant. Such factors as time, type and intensity of mixing, aeration, surface to volume relationship, and power input are still being studied by the Bureau of Mines in hopes of learning how best to condition manganese pulps for oil-emulsion flotation. Other factors affecting flotation of manganese with oil emulsion also deserve attention. A few of these are the influence of stability and proportion of ingredients in the collector emulsion, the feasibility of grinding

Jan 1, 1955