Search Documents

By Arthur McKee

As HEAT is the controlling factor in all smelting operations, it will be .most helpful to make a new set of calculations on the basis of a .unit of fuel burned at the tuyeres to carbon monoxide. This ties together the only two factors in this operation that seem to be constant with respect to each other-the fuel at the tuyere and the air or its oxygen content. If our usual smelting operations, using natural air heated to reasonably obtainable temperatures, furnish sufficient heat above this critical temperature for the purpose, it is doubtful whether additions of oxygen will be of marked benefit. A unit of fuel will not produce a single heat unit more if burned with pure oxygen than if burned with natural air and less heat will be available per unit of fuel by the amount of heat that is carried in by the preheated nitrogen in the natural air of the blast. This is more readily apparent if considered in connection with a heat balance sheet per unit of fuel at the tuyere. The heat available in the stack, as shown by the committee's report, is less by reason of the lower fuel consumption per unit of output assumed in this calculation. The balance sheet for enriched air shows a shortage of the amount of heat usually carried in with the blast; also a lack in the hearth of sufficient heat to melt the 18 per cent. additional metal and slag and in the shaft to the extent of the shaft heat required to heat the 18 per cent. additional stock to the melting point. These heat deficiencies are provided for by the largely increased conversion of carbon monoxide into carbon dioxide, which is assumed, as shown by the following figures: Calculation for natural air: Carbon dioxide 18.4 per cent. (after having eliminated the carbon dioxide from limestone) and 20.8 per cent. of carbon monoxide. Calculation for oxygen-enriched air: Carbon dioxide 28.4 per -cent. and carbon monoxide 23.2 per cent. (no carbon dioxide from stone as lime is charged instead).

Jan 11, 1924

By Francis Pyne

THE following notes are presented in an endeavour to point out the disadvantages attending the use of chrome brick in reverberatory furnaces used in the treatment of materials that are too valuable to allow any great amount of metal absorption by the brick. Several years ago one of the large Eastern copper refineries decided to utilize basic material in place of siliceous material in the walls of their reverberatory furnaces for the treatment of very foul blister copper, as the latter rapidly corroded the siliceous linings. It was also expected that there would be less slag formation, with a consequent decrease in the cost of treatment and a reduction in the metal losses. Magnesite brick were first used, but while the corrosive action of the foul material was greatly reduced, and the amount of. slag formed was very much less, the magnesite proved to be unsatisfactory in certain parts of the furnace, because of its tendency to crack and span badly when subjected to the alternate heating and cooling that takes place in a reverberatory refining furnace. This made many repairs necessary, and consequent frequent interruption in the operation of the furnace, which, together with the high price of the magnesite brick, ran up the cost of maintenance to an unreasonable amount. It was, therefore, decided to substitute chronic brick for magnesite brick in the parts of the furnace affected. The results, as far as the reverberatory furnace was concerned, were very satisfactory. The corrosion due to the action of the foul blister was small and the amount of slag formed was no greater than when using magnesite, and the tendency to crack and spill shown by the magnesite was eliminated. Gradually the use of chrome brick was extended to all furnaces; those treating blister copper as well as those melting cathodes, and the results were so satin-, factory that the siliceous roofs were replaced by roofs of chrome brick except in certain places where experience showed a more satisfactory performance on the part of the silica brick.

Jan 12, 1917

By J. Elmer Thomas

If 1929 witnessed a growing realization on the part of the oil industry that supply must be balanced against demand, 1930 proved conclusively that excessive inventories constitute a price depressant even with balanced conditions. Increased attention was certainly paid to economic considerations last year, and the achievement of holding daily crude production, with a constantly mounting potential, to levels 500,000 bbl. below the output of the summer before, deserves special mention. The ill-advised accumulation, however, of gasoline stocks, at least 10,000,000 bbl. larger than necessary, nullified the restraint exercised by the producers and finally necessitated drastic downward price revisions. An event of special significance was the appointment by the Federal Oil Conservation Board, last March, of a temporary Committee on Petroleum Economics that attempted a forecast of demand, an estimate of supply, and an allocation of the latter between the principal producing states. Thus for the first time was an economic program for an entire basic industry drafted by an independent body under the auspices of the Federal Government. The report was widely discussed and generally approved, but its schedules were not adopted by the refining division nor by oil producers in the State of Texas until too late to contribute to the industry's prosperity during 1930. If the restraint of November had been exercised in May a profitable year might have been the result: The gasoline price war in California during June, however, illustrated the point that even with a fairly sound statistical position insistent pressure to expand normal marketing outlets must result in losses to all concerned. The balanced program so painfully attained by producers must be maintained by refiners and distributors to be completely effective. Again in November the Federal Oil Conservation Board, acting on the request of the directors of the American Petroleum Institute, called its Committee on Petroleum Economics back into existence to prepare a new estimate for the next six months. An economic program adopted in advance of the winter period of accumulating inventories may aid this large and essential industry toward the profits to which it is entitled

Jan 1, 1931

By Jean-Jacques Prompsy, J. S. Rinehart

Some time ago a study was initiated at the Colorado School of Mines in an effort to arrive at a better understanding of the stress fields developed within drill bits under dynamic loading and the influence that these stress fields could have on the failure of the bits. Particular emphasis has been given to the influence that bit shape has on the establishment of highly localized, potentially destructive stress inhomogeneities within the bit. The study has been divided into three phases involving three velocity regimes: impacts at very low velocities, 0 to 20 ft/sec, a velocity range in which dynamic effects are just beginning to be found; impacts at velocities ranging from 20 to several hundred ft/sec, a range commonly encountered in practical drilling operations; and impulsive loading through the detonation of explosives, a region in which the dynamic effects are greatly exaggerated and made more identifiable. The ultimate objective is to provide basic data which will enable the mitigation through judicious design of the frequency and severity of these transient concentrations of intense stress, thereby prolonging and increasing drill efficiency. This paper presents results of the third phase of this study — the development of a better understanding of the dynamics and mechanics of failures caused by transient stress-wave interactions. The impulsive loading or transient waves in these experiments were generated by detonating small explosive charges placed on the ends of Plexiglas cylindrical rods terminating in truncated cones. Under such intense loading, dynamic effects are greatly exaggerated and, hence, made more identifiable. The explosion generates a high-intensity transient stress disturbance which moves through the rod, reflects from surfaces which lie in its path, and establishes momentarily narrow regions of high concentrations of stress where failure of fracture may occur. The peregrinations of these waves, their interactions and their effects have already been described in the literature (see, for example, Refs. 1 and 2). The locations and extent of the regions quite apparently are strongly dependent on specimen shape, making it possible through judicious shaping of specimens to relocate the highly stressed regions, minimize their extent, or eliminate them entirely. These experiments were designed, first, to identify more clearly the vulnerable regions in geometries relevant to drill-bit design and, then, to modify these regions in a predictable way by changing specimen shape. Through this latter process, it is anticipated that better bit design might evolve. The specimens used in the experiments were cylindrical rods, 1 1/2 and 1 1/8 in. in diameter, ended by a truncated cone, with the cone angles ranging from 45° to 130°. Upper cone face diameters were 1/2, 3/4, or 1 in. A small plastic-covered electric blasting cap detonated on the axis of the specimen produced the spherical shock wave. The detonators used were Olin Mathieson No. 6, which induced into the rod a transient saw-toothed stress disturbance of about 3-microseconds duration, corresponding to a wave length of 0.3 in. in the Plexiglas. Five distinct systems of fracture were observed: (1) along the axis of the rod, a lower system of fractures, the cracks focusing around one point for specimens having cone angles of 80° and 90° and, as the cone angle was increased, spreading downward; (2) just above these fractures, an upper system of fractures composed of horizontal cracks observable in some specimens but not of any appreciable extent; (3) a third system of axial cracks still above the latter, observable in the small cone-angle specimens; (4) in the upper part of the specimen, a system of radial fractures extending from the blasting point; and (5) circular spalling due to reflection of the wave on the boundary of the cylinder. Only the first three systems, the axial fractures, are examined here. LOWER TENSILE FRACTURE SYSTEM The first, lower system of tensile fractures, shown in the photograph of Fig. 1, was observed in almost all of the specimens. It was due to the reflected tensile wave coming in from the boundary of the cylinder as shown in Fig. 2. The reflected wave was cylindrically convergent and focused

THE slag performs two useful functions in open-hearth steel- making. First, it is the means of disposal of all the impurities, save carbon, which are removed from the charge materials in refining the steel, so it must be suited to receiving and retaining as much as possible of undesirable elements with minimum loss of iron and useful alloying elements. Second, the slag serves as a buffer between the flame and the bath and transfers oxygen to the metal at a measured pace contrasted with the violent and difficultly controlled oxidation of the bessemer process. At the same time, the slag is a thermal insulator that limits the rate at which heat can be delivered to the metal from the flame, and a heavy slag blanket thereby serves as a brake on production rates. It has been said with justification that the secret of good steel- making is to make a good slag and the steel will take care of itself. In a broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of: (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) Si02, MnO, MgO, and other oxides charged as such or introduced incidentally with ores or fluxes or by refractory erosion, and (3) lime charged or fed to the heat to neutralize the "acidic" oxides present (Si02 and P205). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined; and the control problem would be solved. Unfortunately, only a somewhat imperfect control over these factors is possible, so the operator must begin during the lime boil and continue through the refining period to discover and correct departures from the normal pattern of slag development. To do this as the heat progresses, the first helper must be able to make quick estimates of the composition and physical state of develop-

Jan 1, 1964

By H. W. Reid

One of the outstanding features of the year was a further marked decline in the footage drilled. This is estimated at 169,000 ft., as against 218,000 ft. for the previous year, and 372,500 ft. in 1930. Owing to repair work and improved production methods, there was an increase of about 4.25 per cent in the amount of oil won, the production being estimated at 10,160,000 bbl., or an increase of 400,000 bbl. over 1931 and nearly 750,000 bbl. more than in 1930. (See Table 1.) At the end of November there were 28 rigs in operation. During the first 11 months of the year 54 new wells were started; the average depth of those completed was 2476 feet. Owing to the continued restriction of drilling programs there has been little of outstanding interest in the way of new plant or technique. The use of the acid bottle, for testing the verticality of wells while drilling, has increased considerably, and this is now in use in practically every well except the very shallowest. During the last six months of the year fairly extensive use has been made of electrical coring. The number of wells started in the Colony up to the end of November, 1932, was 1894. The average number of producing wells during the year was 789, or 41.7 per cent of the total. Of these, 214 were flowing wells, 473 pumping, 80 bailing or swabbing, and 22 were produced by air or gas-lift. Although the last category represents less than 3 per cent of the total, there has been a marked increase in the use of air or gas-lift as compared with 1931. During the year there were 16 companies engaged in producing oil, as compared with 14 in the two previous years. In addition to one small refinery which started to operate at the beginning of the year, the five existing refineries worked continuously. At the latter very little has taken place in the way of extensions, except at one in the Parry Lands—Pitch Lake—Point Fortin area, where extensive alterations and additions are in progress, including the building of a deep-water pipe-line pier. When this is completed there will be five loading terminals, all situated in the sheltered Gulf of Paria, or west, coast, capable of accommodating ocean-going tank steamers. There

Jan 1, 1933

By Robert W. Hunt

(Cleveland meeting, October, 1912.) PERHAPS of all the scientific economic questions which have been claiming the attention of capitalists, metallurgists, manu-facturers, directors of public utilities, and the general public of America, during the last few years, none have been of more importance than the one relating to the wear and safety of steel rails. The discovery of the Bessemer process made possible modern railway development. In that growth, as has generally happened in all progressive movements, ill its department have not remained equally balanced. Iron rails permitted the construction of roadways for the passage of power-driven vehicles. In time the speed and weight of such carriages proved too much for the wearing-qualities of the rails, and the limit of railway capacity seemed to have been reached. Bessemer made his invention, which was soon perfected and developed, especially as related to steel rails, and thereby increased the limit of capacity, acid vastly greater railway progress was, made possible. The Siemens-Martin open-hearth process followed, and was later supplemented by the Thomas-Gilchrist basic improvement. For a time the Bessemer steel rails of commerce Were, more than equal to all that was asked of them, but this did not long continue, as evidenced by the records in our Transactions. Revolutionary changes occurred in the industrial world, and in no part of it more than in steel-rail manufacture. Great and powerful commercial combinations were made, whose financial resources made possible the supplanting of the then most efficient blast-furnaces, steel-works, mid mills, by others of theretofore unimagined capacity. Old traditions and practices of steel-making were wiped away, and, in too many cases, output was apparently the chief aim, with the result that much dissatisfaction with the wear and safety of rails was felt by railway officials, and the general public was concerned as to its safety when traveling. The climatic conditions of the winter

Dec 1, 1912

By E. F. Kern, W. W. Loo

A review of the literature on the reduction of cassiterite showed that scarcely any progressive changes were made in the methods of reducing cassiterite until within the last two decades, and that during that period many improvements in the metallurgy of tin have taken place. Since 1914 the world's consumption of tin has increased considerably, resulting in the exploitation of primary tin deposits such as the Bolivian lode, which has become an important source of tin. On account of the low tin content of Bolivian ore, and the presence of objectionable impurities of the reduced tin, the smelting of this ore and the refining of the tin has changed considerably from the methods formerly used. A comparative study of the methods of smelting cassiterite concentrates suggested that an investigation be planned so as to determine what factors effect the extraction of tin from its ores by reduction with carbon. The first part of the experimental work was the determination of whether roasted cassiterite concentrates can be reduced by carbon without the use of flux, and the reduced pellets of tin be collected into a single mass separate from the dry gangue residue. The second part of the experimental work was a comparison of the effect of variations of the different factors on the smelting of roasted cassiterite concentrates: first, the effect of varying the composition of the slag; second, the effect of varying the amount of reducing agent; third, the effect of varying the relative amount of the resulting slag; and fourth, the effect of different kinds of reducing agents. Review of Literature Experiments on the smelting of Bolivian tin concentrates were made by James P. Gill in 1920 in the metallurgical laboratory of the School of Mines, and submitted as a graduate thesis. The results of these tests are fully reported as they are preliminary to the experimental part of this paper, and also because they have not been published. The variables investigated by Mr. Gill were: (a) the effect of temperature on the rate of reduction of cassiterite concentrates; (b) the time required for

Jan 1, 1928

By H. W. Camp

In attempting to summarize and pick out the outstanding development,s in refinery engineering during the past 12 or 13 months, one is immediately impressed by the great strides that have taken place. It is, of course, difficult to obtain the proper perspective with the old year so fresh in our minds, and if relatively minor improvements seem to be given equal recognition with those of magnitude, it will be because the nature of the human mind causes us to place the trivial incidents of today with the important things of yesterday. For instance, the Twenly-Second Semiannual Motor Gasoline Survey (December, 1930) of the U. S. Bureau of Mines shows that the total gasoline yield per barrel of crude increased from 39.6 per cent.. in 1929 to 41.99 per cent. in 1930. This latter fact may appear rather confusing since the production of high-gravity crudes has been steadily increasing. However, during the past yew there has been a reduction in gasoline end point of approximately 8" F. which roughly corresponds to about 1.0 per cent. yield from the crude oil. It appears, therefore, that, if the gasoline mere based on a corresponding distillation basis 1930 would show better yields from the crude than 1929. Cracked gasoline increased from 14.83 per cent. in 1929 to 17.46 per cent. in 1930. Percentage of total gasoline from cracking stills has doubled since 192.5, thus indicating the extent to which this phase of refining has advanced over past years. Replacement of the old shell still batteries by a pipe still and single flash system, with an efficient fractionating tower, has proved advantageous both in fuel consumption and in decreasing space required for the installation. Considerable activity has been shown in the field of vapor-phase cracking, with the development of several new types of units. The production of a product with a high antiknock value makes the vapor-phase processes particularly attractive. Cracking equipment has shown a marked advance with the development of corrosion-resisting alloys. Nickel, chromium and vanadium have shown interesting possibilities, but as yet are fairly expensive. Ceramic material for lining reaction

Jan 1, 1931

By Jerry H. Service, F. L. Partlo

The following investigation was undertaken to develop a method for determining with reasonable accuracy the depth of overburdens of 100 ft. or less. Seismic methods seemed to offer good possibilities. The problem differed from that of the familiar salt-dome location in that the depth of overburden to be determined is much less than is encountered in oil prospecting. This means that a much shorter time interval must be measured with accuracy. Refraction methods seem at present to offer greater possibilities than reflection. The air sound persists for from 0.1 to 0.5 sec., because of echoes, and seismic reflections coming during this time are difficult to detect. A seismometer sensitive to vertical vibrations only offers possibilities and has been used here with some success. It is hoped that the application of this type of seismometer to reflection shooting in this region may be investigated still further. The apparatus used consisted of a carbon-button seismometer followed by a three-stage, transformer-coupled, vacuum-tube amplifier and a General Radio string oscillograph. Time marks are provided by a 1000-cycle, 600-r.p.m., synchronous motor provided with five spokes which intercept the light to the camera at 1/50 sec. intervals. This motor is driven by a two-stage vacuum-tube amplifier of 3 watt output, actuated by a tuning fork. The power supply for the seismometer amplifier is one 2-volt storage and one 45-volt B battery. The motor amplifier is powered by a 6-volt storage battery and 6 to 225-volt, 15-watt motor generator. The temperature-frequency characteristics of the tuning fork have been determined and for ordinary working temperatures the error in time that would be introduced is less than M millisecond for time intervals up to 100 milliseconds. The impact is produced by a sledge blow for surface distances less than 100 ft. and dynamite for greater distances. Two steel balls with wires attached form an electric circuit through a 1-ft. piece of railroad rail upon which they rest. When the rail is struck by the sledge the balls rebound, opening the circuit and indicating the time of impact by a break in the oscillograph record line as at A, Fig. 3. When dynamite

Jan 1, 1934

By David Donoghue

The efforts towards curtailment in Texas have been successful, despite the great area covered and the wide variety of oils offered. There are, of course, examples of noncooperation, perhaps of absolute indifference, but of such it can at least be said that they have benefited from the restrictions imposed elsewhere. The prevention of waste is the legal background for proration in Texas. The legislature in 1899 passed the first laws to prevent waste of oil and gas. Subsequent legislatures, especially those of 1905, 1913 and 1917, undertook to regulate the development and transportation of oil and gas to the end that waste would not occur. In 1917 a constitutional amendment was submitted to the people, providing that natural resources of the state should be conserved and requiring that the legislature pass appropriate laws. This amendment was adopted, and the Acts of 1919 and 1929 have been passed, and these have had the effect of making a rather elaborate plan for the conservation of oil and gas and their protection against waste. In 1930 the new pipe line act, designed to provide for ratable purchases, was passed. The administration of these laws has been placed under the Oil and Gas Division of the Railroad Commission of Texas. The Commission can only consider actual waste, not economic waste. The various proration plans in use in the state, while differing in efficiency, are based on engineering principles. In the proration of flush fields, the limiting of drilling and the steady production of oil under restriction are the principal points involved, and these methods are entirely different from those which prevailed until recently in the Oklahoma City Pool, where apparently nothing beyond the restriction of production on a time basis was attempted. There is little to say in defense of proration in the older and smaller producing areas in Texas, except that, inasmuch as the market outlet has been reduced, proration distributes the market ratably among the producers. Work of Central ProRation Committee In the early part of 1930 the overproduction situation became acute, and, at the request of the Railroad Commission, a committee was formed composed of representatives of the Texas Division of the Mid-Continent

Jan 1, 1931

By A. Long, A. Silverman, J. L. Kulp

Garth Crosby has written an excellent geologic description of the deposits surrounding the Gem stocks in the Coeur d'Alene district. The ore deposits in the area of the Gem stocks may hold the key to the age and mineralization history of the entire Coeur d'Alene district. A recent isotopic study10 of the Coeur d'Alene district in this laboratory illustrates that a classical geologic interpretation of these deposits, with its implications for the whole district, may lead to erroneous conclusions. For this reason it seems pertinent to submit a summary of these results and an interpretation of the mineralizing history of the Coeur d'Alene districts. Pitchblende from the Sunshine mine has been dated as 1100-1200 million years (m.y.) by Kerr and Kulp,11 and Eckelmann and Kulp.12 This pitchblende is known to predate the major sulphide introduction in the Sunshine mine, but it clearly follows the metamorphism and folding of the Belt Series. Recently, Goldich (personal communication) dated sericite from the Belt rocks as 1200 m.y. by the potassium-argon method. This date establishes a minimum Belt age if the sericite is of metamorphic origin and a maximum age if detrital. The Belt Series, therefore, is not latest Precambrian. Lead isotope ratios of galenas have been measured and model ages calculated by Bate, et all3 for the Sunshine mine, Farquhar and Cummingl4 or the Bunker Hill and Sullivan mine, and Cannonl6,18 for a few other deposits in the district. Galenas from similar deposits in Southern British Columbia have been measured by Bate, et al,23 Farquhar and Gumming,11 and Wanless and Leech." The new work in this laboratory includes leads from ten widely scattered mines north and south of the Osburn fault, and through a vertical distance of over 5000 ft (Star mine). Included in this group are the Hercules, Sunset, and Mountain Goat mines, which are adjacent to the Gem stocks. In addition, galenas from stringers which cut the Gem stocks in the Success and Sunrise mines and the Hercules hanging wall dike in the lower western portion of the Hercules mine, were included in the study. All of the above leads, except one, give model ages of 1300-1400 m.y. for the time of segregation from the parent material. The concordance of the common lead and U-Pb ages, the great horizontal and vertical uniformity of the lead ratios, the sulphur ratios of two Sunshine mine galenas and three galenas from the Edith, Page, and Hercules mines indicating average crustal sulphur, and the U23/Pb204 ratio inferred for the original lead environment, indicate that the entire mineralization of the Coeur d'Alene-British Columbia base metal belt was derived from a deep source and emplaced in the Precambrian. One sample of galena from sulphide stringers cutting the North Gem stock at the Sunrise Prospect mine gave a modern (i.e., Tertiary) lead ratio. This mine is located at the northern tip of the stock. The presence of modern lead suggests mobilization of some rock lead during the intrusion of the Gem stocks and their outliers. Larsen et al.l8 have dated the Gem stocks as Tertiary by the lead alpha method. If Coeur d'Alene mineralization was genetically related to Tertiary magma formation and intrusion

Jan 1, 1961

MONTANA SECTION W. C. SIDERFIN, Chairman, OSCAR ROHN, Vice-Chairman, E. B. YOUNG, Secretary-Treasurer, 526, Hennesey Building, Butte, Mont. F. W. BACORN, C. D. DEMOND. The semi-annual meeting of the Montana Section was held at the Silver Bow Club, Butte, Montana, on Friday, Nov. 16, at 8 p. m.; this was a postponement of the regular October meeting because of conflict in date with the St. Louis meeting of the Institute. An informal dinner was served to 68 members and guests. After dinner, Chairman W. C. Siderfin called the meeting to order. The minutes of the annual meeting, of Feb. 2, 1917, and the special meeting of May 21, 1917, were read and approved. C. W. Goodale led the discussion with "Notes on the St. Louis Meeting." He was followed by J. H. Warner who spoke on " The Joplin and Miami Districts," and by J. L: Bruce, Alexander Leggatt, N. B. Braly, and E. B. Young, the latter speaking on the work of the War Minerals Committee; and on the Cosden Oil Refinery at West Tuba, Okla. R. H. Sales reviewed briefly the manganese situation. E. N. Norris presented a paper on "Fire Proofing of Mine Shafts by the Anaconda Copper Mining Co." This resulted in interesting discussion by C. L. Berrien, C. E. Nighman, N. B. Braly, W. B. Daly, B. H. Dunshee, and J. J. Carrigan. C. L. Berrien and C. E. Nighman presented their papers on "Fire Extinction by Hydraulic Filling." In view of the late hour, discussion was waived. The executive committee, by unanimous consent, decided to request written discussion of the above papers to be presented at the next meeting, in February. B. B. Thayer spoke interestingly on the work of the Naval Consulting Board, and referred to the arsenic situation. Spencer Miller, also a, member of the Naval Consulting Board, entertained the-meeting with a vivid description of the method of "Coaling Battleships at Sea." Robert Sticht of Tasmania, in a short talk, spoke feelingly of his relations with the United States. At a late hour adjournment ended a most successful and interesting meeting. E. B. YOUNG, Secretary.

Jan 1, 1918

By George C. Stone

The stack gases from regenerative furnaces lare very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300" C. (572" F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450". The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 1, 1914

By A. B. Hildebrandt

P. B. Baxendell is to be complimented for an exccllent piece of work. To our knowledge there has been no previous publication of field data on the flow of oil and gas through the annulus of a well. It is certainly gratifying to see this work on annular flow confirm the previous published correlation procedure on tubing flow. It extends considerably the range under which reliable gas-lift calculations can be made. Baxendell discussed this work with us about a year ago and was kind enough to send a large scale plot of his correlation. We had been designing gas-lift installations on flow through the annulus, assuming that the original correlation of the f factor based on tubing flow' was valid as long as we stayed within the same mass velocity range on which the correlation was based. Doing this work necessitated the use of an equivalent diameter for the annular flow. The equivalent diameter is defined as area' of stream cross section wetted perimeter and for the case of an annulus is D, — D,. Substituting this in the basic equation correlating energy loss along with the area to flow required to convert the velocity, to volumetric flow rate, D (Baxendell's Eq. 7) becomes dell's expression, D,). Similarly, the D in 1.4737 X 10 (M&/D) becomes (D, + D;) for annular flow. On receipt of Baxendell's data, we. of course, recalculated it to put it into the form we were using, and to see how well it agreed with the correlation based on tubing flow. Fig. 1 shows the results, which were certainly gratifying. For low values of (D, - D,) pv, the data coincide with the data on flow through tubing, whereas at high values the data on flow through the annuli appear to be leveling off to a constant value. For very high rates of flow where the turbulence is very high, one might expect the value f to level out and become constant. A bulletin published in 1914 by the U. of Wisconsin presented results of a large number of laboratory teats in air lifting water through short lengths of 1.25-in. tubing. It was possible to correlate a random sampling of

By Rustum Roy, E. F. Osborn

THE investigation discussed in this paper concerns phase equilibria in the alumina-silica-water system. Studies in this system are part of a re¬search project sponsored by the Geophysics Branch of the Office of Naval Research2 directed toward increasing knowledge of the stability relations of metamorphic mineral assemblages. Inasmuch as metamorphic rocks consist largely of aluminosilicate struc¬tures, many of them hydrated, the system alumina-silica-water is a logical starting point for the systematic laboratory study of metamorphic mineral systems. Although logical, this is not, however, an easy approach to the problem because of the very great difficulty of obtaining transformations among structures in response to changes in temperature, pressure, and con¬centration. Commonly equilibrium among the phases in this system is exceed¬ingly difficult to attain. New laboratory techniques are required to produce certain structural rearrangements, such as inversion of diaspore to boehmite or the transformation of alumina-silica mixtures to andalusite or kyanite. Phase equilibrium data for the alumina-silica-water system are consequently only partly complete, and only a summary progress report is presented here. Crystalline phases in the alumina-silica-water system are numerous and many are common minerals. The oxide components exist as: quartz, tridymite, cristobalite, corundum, water, and ice. Binary compounds occurring naturally are: sillimanite, andalusite, kyanite, and mullite in the alumina-silica system and gibbsite, boehmite, and diaspore in the alumina-water system. The most abundant among the ternary compounds is the composition A12O3.2SiO2.¬2H2O, existing in the four structural modifications, kaolinite, nacrite, dickite, and halloysite. The hydrated form of halloysite, A12O3.2SiO2.4H2O, is here called endellite. Pyrophyllite, A12O3.4SiO2.H2O, is the third ternary compound of natural occurrence. In addition to these minerals, two other ternary crystalline phases have been encountered in this study. The first is a structure resembling montmorillonite and corresponding perhaps to the pure aluminian end member of the beidellite series. The other has a composition approximating A12O3.2SiO2.H2O but its composition and structure are still in doubt. LABORATORY PROCEDURE In these laboratory studies, a starting material such as an alumina-silica gel or one or more of the crystalline phases is wrapped in platinum foil,

Jan 1, 1952

By Bradley Stoughton

PROMINENCE has been given lately in engineering circles to the question whether an organisation with manifold interests can be as effective as one with a single aim, especially if that single aim be the furtherance of affairs of moment and the welfare of engineers in general. In its earlier days, the A. I. M. E. was forbidden by its constitution to engage in non-technical public affairs, but the members altered the constitution in this respect, in the year 1912, in response to the growing demand that engineers be more human in their interests and that the engineering societies represent them in this respect. Since that time, the activity of mining engineers in public affairs has been growing rapidly, and we are happy that the Institute has been able to render very valuable economic services. Doubtless the greatest public service rendered by engineers in a recent great emergency was the work of the Naval Consulting Board, without which the U. S. Navy would never have been able to enter promptly into service upon our entrance into the war, ,and both Navy and Army would have been a long time without the munitions that came at an early date. We can never forget that this Board was established through the direct activity of the then President of the A. I. M. E., with the hearty cooperation of other national organizations.

Jan 1, 1920

By Terkel Rosenqvist

THE desulphurization of molten iron and steel is a very complicated process. One way to arrive at a better understanding of this process is to break it down into several simpler chemical processes that can be studied individually in the laboratory. For a study of the different factors that influence the equilibrium distribution of sulphur between liquid metals and slags, several simpler equilibria may be investigated. One very important subject is the determination of the escaping tendency of sulphur in the liquid metal and its dependency on temperature and composition of the melt. Several papers in this field have recently been published.', ' Another subject is the study of the sulphur capacity of the slag. A molten slag is indeed complex, and even if sulphur distribution data for a large variety of molten slags may give empirical data about their desulphurizing power, the importance of the individual components is still not quite clear. It is accepted generally that lime is the most important desulphurizing component in the slag. The present investigation has as its purpose to study the desulphurizing power of lime in its standard state, and to provide a basis for thermodynamic calculations of the desulphurizing power of various lime-containing slags. The standard state of lime at steelmaking temperatures is solid calcium oxide, CaO. It can react with sulphur to form solid calcium sulphide, CaS. The relative stability of calcium oxide and calcium sulphide is expressed by the free energy of the reaction: 2Ca0 (s) + S1 (g) = 2CaS (s) + O2 (g) The existing free energy data for this reaction, listed by Kelley5 nd Osborn,' are uncertain to about 10 kcal and are of limited value for a calculation of equilibrium constants. Under the conditions prevailing in a melting furnace, the sulphur pressure may be expressed conveniently by the ratio H,S/H2 and the oxygen pressure by the ratio H,O/H, (or CO,/CO). The desulphurizing power of calcium oxide may, therefore, be studied by the reaction CaO + HIS = CaS + H2O. A study of this reaction may be complicated by certain side reactions: Water vapor and hydrogen sulphide may react. to form sulphur dioxide, and calcium sulphide may be oxidized to calcium sulphate. A thermodynamic calculation shows that these side reactions will be suppressed to insignificance if the equilibrium is studied in the presence of an excess of hydrogen. The apparatus used is shown in Fig. 1. About 10 g calcium oxide and 20 g calcium sulphide (laboratory qualities) were intimately mixed, and some water was added to make a thick paste. The paste was put into a thimble of zirconium silicate, which was placed within the constant temperature zone of a furnace, and capillary refractory tubes were attached in both ends. After the mixture had been heated in dry hydrogen at 1000°C for several hours all Ca(OH), and CaCO, had decomposed and CaSO, was reduced, so only CaO and CaS remained in the thimble forming a porous plug. The mixture was examined by X-ray diffraction after the initial reduction in dry hydrogen as well as after the subsequent experimental runs up to 1425 °C. It was shown that crystalline calcium oxide and calcium sulphide were always present together in about equal amounts. The unit cell edges were found to be 4.80A for CaO and 5.68A for CaS in good agreement with existing literature values." This shows that the mutual solid solubility is very small, and that the compounds are present in their standard states. Purified hydrogen was passed through water sat-urators kept at constant temperature in a thermostat bath. The amount of water vapor saturation was checked by means of a dew point method, not shown on Fig. 1. The gas mixture was passed through the capillary inlet into the furnace, where it was sifted through the porous plug of calcium oxide and calcium sulphide. The hydrogen sulphide present in the outgoing gas was absorbed in a zinc acetate solution and the hydrogen was collected over water. When one liter of hydrogen had been collected, the amount of hydrogen sulphide was determined by iodometric titration. As one molecule of H,O is used for the formation of each molecule of H,S, the equilibrium ratio H,S/H,O would be , where (H,O) is the molar concentration in the ingoing gas, and (H,S) the molar concentration in the outgoing gas. In the present work (H,S) was always very small compared to (H20). In order for the observed H,S/H20 ratio to represent the true equilibrium ratio the gas flow has to be: 1—Sufficiently slow to give a complete establishment of equilibrium, and 2—sufficiently fast to counteract thermal diffusion. Incomplete reaction would give a value decreasing with increasing flow rate, and thermal diffusion would give a value increasing with decreasing flow rate. When inlet and outlet tubes of about 2 sq mm cross-section were used, the observed gas ratio was independent of the flow rate between 15 and 125 cc per min, Fig. 2. In this range, therefore, the observed gas ratio represents true equilibrium.* For the rest of the in-

Jan 1, 1952

By A. D. Smigelskas, E. O. Kirkendall

THIS is the third paper in a series on the diffusion of zinc in alpha brass.1 At the time of the first-paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; however, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. PROCEDURE A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about ¾ in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 ± .0002 in. (1.0625 ± 0.0005 cm.) thick. Six 0.005-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in copper and alpha brass, were stretched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every ½ in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1946

By H. E. Williams

In view of the frequent occurrence of petroleum in other parts of the world, it seems odd that so large an area as is contained within the borders of Brazil should be without this product. This apparent deficiency may be due, however, to our ignorance of the regions in which it may exist. In some places, indications point to the probable existence of petroleum in ages gone by; and while the presence of petroleum pools may be problematic, in several regions conditions not unfavorable to their occurrence exist. Yet, Brazil has enormous oil resources in the rich oil-shales in different parts of the country. Many of these shales are very rich and only suitable processes for the extraction of the oil are lacking. At the present time, only a few small experimental plants are producing oil by distillation from these shales. These plants have been the subject of recent investigations by the Geological and Mineralogical Survey, a preliminary report of which is in the hands of the printer. The only regions where studies have not been made are the upper Amazon, the Acre, the Rio Negro, and the Peruvian frontier, which really seems to be the most promising field for explorations of any in the country. In the vast plateau region of the interior north of the 20th parallel of latitude, granites, gneiss, mica schists, and very old metamorphosed sedimentaries predominate. Later, sedimentaries occupy a minor position and, where found in the interior, represent a thin veneering resting on the older rocks. At several places near the coast they have a greater development and contain considerable beds of oil-shale and may, .in some cases, offer conditions favorable for the occurrence of oil. Such deposits are found in the Permian rocks of central and southern Maran-hao; in the Tertiary and Cretaceous beds along the coast of Alagsas Sergipe, Bahia, and perhaps farther south in Espirito Santo; and in the Parahyba embayment north of Cape Frio and in the interior Tertiary basin of eastern Sao Paulo.

Jan 1, 1921