Search Documents

By R. R. Bassermann

THE property of Howey Gold Mines, Limited is situated at Red Lake, Ontario, one hundred and seventy-five miles east of Winnipeg and eighty miles north of the Canadian National Railway line. The mine has been a continuous producer since April, 1930, and at present is hoisting 1,350 tons of ore per day. The shaft consists of three compartments (see Figure 1, sketch B). Hoisting is done by two skips in balance, one of which is interchangeable with a cage. Sinking had been carried out at three different periods. From the surface to the 550-foot level, the sets had been spaced at seven-foot intervals, from the 550-to the 1,060-foot level at six feet, and from the 1,060-to the 1,500-foot level at five feet. During the five years of operation, the shaft had become so badly worn, due to spill from the tipples and, to a certain extent, from the loading pockets, that re-timbering was considered necessary. It should be explained that no crushing is done underground because of the ad verse effect this would have on the efficiency of the sorting. The grizzly rail clearance above the ore pockets is fourteen inches and consequently the ore hoisted is extremely coarse. More than average spill from the loading pockets and tipples under such conditions is inevitable, and it is debatable whether underground crushing with consequent increased sorting costs would not be justified. The cost of complete re-timbering according to standard practice would have been prohibitive both directly and indirectly: A lengthy shut-down of the shaft, with the consequent disorganization of the staff and workmen, could not be considered. Accordingly, it became necessary to devise some method of repair that could be carried to completion in a very limited period of time. The shaft timber for the first 250 feet was not in need of repair. From the 250-foot to the 1,060-foot level the wall plates, posts, and blocking were in good condition. These had been protected by a one-inch plank lining put in at various periods during the past three years without interfering with hoisting operations. The end plates and dividers, however, could not be protected in this manner because of the lack of skip clearance. It was decided that, if the dividers in this section could be replaced, the shaft would be as satisfactory as if completely re-timbered. Several factors had to be taken into consideration in deciding on a suit-able method of repair. In the first place, the tipple plates had to be re-designed. To complete the job in a reasonable time, not only had work to be done on the tipple, but simultaneously from several points in the shaft itself. Since all power cables, pipe lines, etc., were in the manway compartment of the shaft, this compartment had to be left undisturbed.

Jan 1, 1935

By C. Matthews, A. Vo

"Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations.INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $30/tonne according to the Metal Bulletin Iron Ore Index. At a shipload of 180kt this would be a variation of US $5.4M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product."

Jan 1, 2019

By Tassos Grammatikopoulos, Sarah Prout, William Mercer, C. Gunning

"The Nechalacho rare metal deposit is located in NWT, Canada. Avalon Rare Metals Inc. is now evaluating processing techniques for recovery of REE to be used in the industry. QEMSCANTM analysis coupled with whole rock, REE, Zr and Nb, and electron microprobe analyses were utilized to identify and quantify the mineralogy of the deposit, and define the REE distribution among minerals. QEMSCANTM mineralogy was performed on fifty intact drill samples using EXPLOMINTM that provided textural information for the mineralization; crushed samples were used to determine the variability of the ore and define REE domains, and composite samples to determine the liberation and association of the REE minerals. The sample matrix predominantly consists of biotite, feldspars, quartz, muscovite/clays, minor chlorite and amphibole, magnetite and hematite and carbonates. REE include in decreasing order of abundance allanite (3.6%), monazite (1.5%), synchysite (0.9%), columbite (0.9%), fergusonite (0.6%), bastnaesite (0.4%), and zircon 11.0%. The majority of the HREE are carried by fergusonite and zircon, and the LREE by monazite, allanite, synchysite and bastnaesite. QEMSCANTM mineralogical data is extremely valuable in assessing the mineralogy of the ore. The data have been implemented in defining the mineralogy of the ore body, support metallurgical test work, predict recoveries and grades, and finally calculate reserves of the deposit.INTRODUCTIONAvalon is in the unique position of owning and developing one of the world’s largest rare earth deposits in the Northwest Territories of Canada.The term Rare Earth Elements (REE) is used to describe the 15 lanthanide elements or metals and, more recently, the metals yttrium and scandium, which display similar physical and chemical properties. REE are not particularly rare and have a similar abundance in the earth’s crust to nickel, tin or tungsten. Unlike these better known metals however, the rare earths have little tendency to become concentrated into commercial ore deposits. When they do become concentrated, deposits of REEs usually display enrichment in one of two groups. The most commonly occurring deposits of REEs contain a sub-group of elements referred to as the “light rare earth elements” (LREEs), which include lanthanum, cerium, praseodymium, neodymium, and samarium. Less commonly, deposits of REEs contain the much more valuable sub-group of elements referred to as the “heavy rare earth elements” (HREEs), which include europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium and lutetium. Yttrium and scandium most commonly occur in association with this second HREE sub-group. Generally, LREEs are produced from the mineral bastnaesite, and the HREEs have been produced from the minerals xenotime and monazite. LREEs continue to be produced from bastnaesite, however in the 1980s, China started production of HREEs from unique laterite clay deposits. China now produces approximately 95% of the world’s rare earths."

Jan 1, 2011

By A. H. Mumin, A. Prikhodko

"This paper provides an understanding of interpreting and evaluating airborne time domain electromagnetic (TEM) surveys as applied to massive sulfide exploration. Variations in the conductive morphologies of massive sulfide ore systems are discussed, followed by forward modelling exercises examining the derived TEM response to these morphologies and discussion of the subtleties of data interpretation. Deposit morphology in the orientation at formation and the variations occurring due to later deformation are considered. Images of corresponding resistivity–depth models are provided. The combined modelling results provide a low-cost method for initial interpretation and screening of TEM anomalies. RÉSUMÉ Cet article nous permet de mieux comprendre l’interprétation et l’évaluation des levés élec-tromagnétiques aéroportés en domaine temporel (TDEM, de l’anglais time-domain electromagnetic) appliqués à l’exploration du sulfure massif. Y sont débattues les variations au niveau des morphologies conductrices des systèmes de minéralisation du sulfure massif, suivies d’exercices de modélisation prospective qui examinent la réponse dérivée des TDEM à ces morphologies et d’une discussion sur les subtilités de l’interprétation des données. L’étude envisage la morphologie de l’orientation originelle non déformée des gisements ainsi que les variations résultant d’une déformation ultérieure. Des images des modèles correspondants de résistivité-profondeur sont fournies. Les résultats combinés relatifs à la modélisation proposent une méthode peu onéreuse d’interprétation et de contrôle initiaux des anomalies dans les TDEM.INTRODUCTION Electromagnetic geophysical surveys are an indispensable foundation of many mineral exploration programs and can account for as much as half of the predrilling exploration costs. Quantitative mass interpretation of the survey results remains difficult due to the infinite variation of deposit morphologies, their complex physical properties, and the presence of barren conductive materials that can mimic or mask the response of targeted ore. Many modern geophysical investigations that focus on time domain electromagnetic (TEM) data interpretations are devoted to problems with inversion and modelling and their algorithms. Although a few of these investigations have resulted in commercial software products, these require highly qualified and experienced users and usually include geometric assumptions. Furthermore, without the input of known physical properties and geometric constraints, the inversion results are highly ambiguous. A number of case studies document the geophysical responses to known targets in well-defined and diverse geo-electrical environments, providing a high degree of correlation between field obser-vation and the results of the modelling used in this style of investigation (Hone, 1980; Schneider & Emerson, 1980; Tyne, Idnurm, & Malone, 1981; Bishop & Lewis, 1992; Hopgood & Hungerford, 1994; Meju, 2002; Yang & Oldenburg, 2016). The uniqueness of the target/environment parameters and their specific features limits the use logy is poorly understood. The responses are therefore that are devoid of complicating environmental factors (e.g., highly conductive overburden and hostrocks or nonuniform target conductivity) as a first approach to the interpretation process of such case studies as the main reference for interpreting TEM survey responses in areas where the underlying geomodelled from generalized and typical geological models"

Jan 1, 2018

By Lawrence D. Meinert

Abstract-Most large skarn deposits are zoned in both space and time relative to associated intrusions. Zonation occurs on scales from kilometers to micrometers, and reflects infiltrative fluid flow, wallrock reaction, temperature variations, and fluid mixing. The most spectacular examples of skarn zonation usually occur at the skarn-marble contact, where transitions between monomineralic bands can be knife sharp. Other small-scale examples occur in zoned veins and individual mineral crystals. Although, visually striking and scientifically interesting, in mineral exploration these small-scale variations are less useful than deposit- or district-scale zonation. In most skarn systems there is a general zonation pattern of proximal garnet, distal pyroxene, and vesuvianite (or a pyroxenoid such as wollastonite, bustamite, or rhodonite) at the marble front. As well, individual skarn minerals may display systematic color or compositional variations within the larger zonation pattern. Such patterns are reviewed for 14 well-studied examples of Cu, W, Sn, Au, and Zn-Pb skarns. In addition, many deposits have endoskarn or other alteration of the associated intrusion, and recrystallization or other subtle changes have occurred in the surrounding wallrocks. Copper skarns, such as Mines Gaspé in Quebec and Big Gossan in Irian Jaya, have high ratios of garnet:pyroxene and are zoned outward from the intrusion, to garnet, to pyroxene, to massive-sulfide replacement and vein deposits. Garnets in Cu skarn are Fe-rich and change from dark red-brown near the intrusive contact to paler brown, green, or yellow in distal locations. Pyroxenes in Cu skarns are pale and diopsidic near the intrusion, and become darker and more Fe- and Mn-rich away from the intrusion. Tungsten skarns, such as Salau and Costabonne in France and Pine Creek and Garnet Dike in California, have intermediate ratios of garnet:pyroxene, are more extensive vertically and along strike than perpendicular to the intrusive contact, and have zonation patterns commonly complicated by overprinting of metamorphic lithologies. In W skarns, garnet is commonly subcalcic and the pyroxene is Fe-rich, reflecting particularly reducing wallrocks or great depth of formation. Tin skarns, such as Dachang in China and Moina in Australia, also can have subcalcic garnet and Fe-rich pyroxene, but this reduced mineral assemblage typically is due to an association with reduced S-type granites. Tin skarns differ from most other skarn types in having a late greisen stage that may replace earlier Sn-bearing calc-silicate minerals, thus liberating Sn to form cassiterite. Many high-grade Au skarns, such as Hedley in British Columbia and Fortitude in Nevada, have low ratios of garnet:pyroxene and are associated both with reduced plutons and reduced wallrocks. Goldrich zones occur in Fe-rich, pyroxene-dominant, distal skarn. Zn-Pb skarns, such as the Yeonhwa- Ulchin district in Korea and Groundhog in New Mexico, have low ratios of garnet:pyroxene and generally form distal to associated intrusions. These skarns also are zoned from proximal garnet to distal pyroxene and pyroxenoid (bustamite-rhodonite), with significant zones of massive sulfides within and beyond skarn. Manganese enrichment of most mineral phases, particularly pyroxene, is characteristic of distal zones. Fundamental controls on skarn zonation include temperature, depth of formation, composition and oxidation state of associated plutons and wallrocks, and tectonic setting. Most W skarns form at relatively great depth, 5 km to 20 km, with extensive high-temperature metamorphic and metasomatic mineral assemblages. In contrast, most other skarn types are relatively shallow, <10 km and mostly <5 km, with limited, lower temperature metamorphic aureoles. Differences in oxidation state correlate well with different skarn zonation patterns, particularly garnet:pyroxene ratios and compositions, and can be used in both classification of and exploration for s

Jan 1, 1997

By M. Rylatt, E. Legault-Seguin, C. Mohns

"With energy costs increasing and ore grades diminishing, the role of preconcentration in hard-rock mining operations has gained greater interest. Dense medium separation is a process that can be conducted at particle sizes from 250 to 0.50 mm with high separation efficiency, depending on liberation characteristics of the valuable minerals. Pilot-plant case studies conducted at the SGS Lakefield site are presented, including mineral systems such as spodumene, sulfide-bearing gold ores, and complex sulfide ores. These case studies demonstrate that, for amenable ores, mass rejection of 20–60% is possible while maintaining recoveries of greater than 90%.RÉSUMÉ Au vu de la hausse des coûts liés à l’énergie et du déclin de la teneur des minerais, le rôle de la préconcentration dans les exploitations minières en roche dure présente un intérêt croissant. La séparation (ou concentration) en milieu dense est un processus pouvant être mené sur des calibres de grains de 250 à 0.50 mm avec un rendement élevé de séparation, en fonction des caractéristiques de libération des constituants des minéraux métallifères. Sont présentées dans cet article des études de cas menées dans des usines pilotes du site de Lakefield de SGS, lesquelles incluent des systèmes de minéraux tels que le spodumène, les minerais aurifères sulfurés et les minerais sulfurés complexes. Ces études de cas montrent que pour les minerais présentant les caractéristiques de libération appropriées, il est possible d’atteindre un rejet en masse de 20 à 60 %, tout en maintenant des récupérations supérieures à 90 %.INTRODUCTIONPreconcentration is the process of rejecting gangue minerals while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Preconcentration has been practiced in the industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, which typically require finer grind sizes and incur higher energy costs.The benefits of preconcentration are:• lower mining costs, which allows for nonselective mining;• lower process capital and operating costs (e.g., resulting from reduced grinding, flotation, and fines disposal stages);• increased ore reserves, which provides the potential to treat lower grade ore;• increased mine production without expansion of the existing plant or concentrator;• reduced overall tailings impoundment by converting the reject into a byproduct (e.g., underground backfill or aggregate);• improved efficiency of downstream processes (e.g., silica removal in electric arc furnace feed, removal of softer sliming minerals prior to grinding);• potential application to brownfield operations and greenfield projects; and• a “green” process option, which reduces processing energy consumption;– reduces mill feed;– increases stage metal recovery (higher grade feed);– increases mill metal output per tonne processed;– reduces surface plant, tailings dump, and tailings pond requirements because the plant has a small footprint and can be installed underground; and– can be applied to retreatment of old tailings dumps to recover metal values and reduce environmental impacts (e.g., dissolved metal runoff, acid drainage)."

Jan 1, 2017

By D. Bois, P. Poirier, B. Bussière

Environmental desulphurization is an attractive alternative for the management of acid generating tailings. Bulk sulphide flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works. This process can reduce the volume of problematic tailings to manage by making a sulphide fraction concentrate. The desulphurized tailings can then be used as construction material for an engineered cover to prevent acid mine drainage. In this paper, the results from different laboratory and pilot scale flotation tests are presented. These results confirm that low sulphide non-acid generating tailings can be produced by froth flotation. It is also demonstrated that sulphide concentrates obtained from desulphurization mixed with the appropriate binders can be used as feed material for paste backfill. From previous work on the evaluation of operating and capital costs of the desulphurization process for different ore types, the use of desulphurization as a tailings management approach was studied for several scenarios. The desulphurization process was then compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation. Results show that partial or total desulphurization are technically and economically viable options to manage tailings during mine operation. Mine waste managers should consider desulphurization as an efficient technology.

Jan 1, 2005

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015

By P. T. O'Kane

The PLATSOL® process, initially developed for the treatment of the NorthMet Cu/Ni/PGM concentrate, has seen over the recent years its applicability extended to include numerous other Cu/Ni concentrates of the same type, as well as other precious metals-containing feedstocks. However, several concentrates were found refractory to the typical PLATSOL® conditions, more particularly so the platinum. Attempts to extend those conditions, such as higher temperatures (250°C), longer retention time, increased oxidation conditions, higher chloride additions, were not successful. Detailed mineralogical investigation of those PLATSOL® leach residues indicated the main refractory mineral to be cooperite (PtS). Further metallurgical investigations showed that a thermal pre-treatment of the concentrate effectively unlocked the refractory platinum minerals for the subsequent leach. Temperatures between 400 and 750°C were tested, with the optimum being found around 650°C. The kinetics of the pre-treatment process were fast, and one hour at temperature proved sufficient. Under those conditions, PLATSOL® extractions were re-established around 95% for both platinum and palladium. From a mineralogical examination of the calcine, it was shown that the effect of the pre-treatment was to transform the cooperite and other refractory sulphides into metallic platinum and alloys, amenable to the PLATSOL®. The implications of the pre¬treatment step for the processing of PGM concentrates arc briefly discussed.

Jan 1, 2004

By W. J. Langford

"Conventional design criteria assume that the fracture strength of a structural material exceeds its yield strength. Fracture below the design load is not expected, y et many structures have failed in this way. The causes of the fractures are almost always discontinuities such as cracks and welding defects. Linear Elastic Fracture Mechanics (LEFM or simply 'fracture mechanics') provides an analytical framework for assessing the influence of sharp defects on the load-bearing capability of a structure. Fracture mechanics techniques have reached the point of acceptance by ASME Design Codes for nuclear components, and ASTM Standards now include well-defined rules for measuring fracture toughness. Starting with a simple equation which relates applied stress and crack size, the influence of the material's thickness and yield strength can be calculated. Thus, the size of defect which will cause failure under the applied stress may be determined. Armed with this information, the metallurgist can assess the safety of a structure from the viewpoints of non-destructive testing standards, construction standards and conditions of operation throughout its service life."

Jan 1, 1976

By H. Bouzahzah

The field of quantitative mineralogy has evolved significantly through the development of image analysis techniques and information technology. Quantitative mineralogical characterization can now be routinely conducted for determining ore compositions and understanding the behaviour of minerals within mineral separation processes. The characterization of mine tailings is another important application of quantitative mineralogy. The estimation of acid and neutralization potential as well as the interpretation of kinetic leaching test results are often based on quantitative mineralogical knowledge (mineral abundance, texture, metal distribution amongst minerals, etc.). The objective of this paper is to determine and compare the accuracy of four mineralogical characterization techniques that are often used for environmental sample analysis: (1) X-ray diffraction, (2) normal analysis from chemistry analyses, (3) normal analysis from specific gravity measurements and (4) SEM-EDS image analysis. For this purpose, three artificial samples were assembled by mixing pure minerals in proportions often observed in mineral processing plant tailings. BILMAT, a statistical data reconciliation software, was applied to reconcile the chemical analyses with the results of other mineralogical analysis techniques and to estimate the acid and neutralization potential of actual mine tailings samples. The acid mine drainage was qualified from the acid potential and neutralization potential equilibrium as determined through quantitative mineralogical analysis. The statistically reconciled data made it possible to predict the metal deportment as a function of their bearing minerals and therefore, in the case of neutral contaminated drainage, to assess metal leaching potential.

Jan 1, 2016

By J. C. Roy, S. Couture, C. Barbeau

The chemical composition of the asbestos tailings from different mines in the Eastern Townships of Quebec are fairly uniform in composition. The serpentine minerals antigorite and chrysotile form about 85 to 90 per cent of the total. Iron oxides add another 7 to 10 per cent; magnetite represents about 70 per cent of the oxides. Chromite is present in amounts of about 0.5 per cent. The average contents of elemental magnesium, iron and nickel are 23, 6 and 0.25 per cent respectively.

Jan 1, 1972

By D. H. Stonehouse

Of the f ive Canadian cement producing regions- Atlantic, Quebec, Ontario, Prairie and Pacific-Ontario has the greatest capacity and normally produces the most cement. However, during the last 5 years the greatest activity within the industry in Canada has been in the Prairie and Pacific regions where major capacity increases have taken place. Most Canadian cement companies produce normal Portland, high-earlystrength Portland and sulphate resisting Portland cements. Some companies also manufacture moderate Portland cement, and low-heat-of-hydration Portland cement. Escalating energy costs highlight the need for technology research into more energy-efficient equipment for the energy-intensive cement industry. The industry is well integrated and plants are well situated to support construction in Canada. Expansion into the United States has become common during the past decade.

Jan 1, 1984

By A. O. Dufresne

WITHOUT transportation, mining would be quite impossible. Any person familiar with the operation of a mine knows full well that from the minute ore is blasted, it is kept moving until it reaches the treatment plant. In the mill, by means of conveyors and elevators, the ore is brought from receiving bins to one machine after another until finally its valuable mineral is separated from the gangue. The finished product must then be shipped -either by boat, rail, or motor trucks to industrial centres, where it undergoes further treatment and transformation into finished commercial goods. Everybody appreciates that the winning of an or-e includes, amongst various operations, the moving of large quantities of material of generally low value. Transportation, therefore, must be considered One of the most important factors in the economics of mining. My assignment, this afternoon, is not to treat of that phase of transportation as it directly affects mining operations, but rather to consider some of the aspects of overland transportation and its influence in bringing about the development of mining camps in Canada. I shall take the liberty of rapidly surveying conditions facing prospectors, mine developers and operators from the time a region is still in a pre-pioneering stage until such time as a mine starts shipping its concentrates.

Jan 1, 1956

By P. J. Lunder, R. C. Pakalnis

This paper presents the results of research that has been undertaken in order to develop an improved method of determining the strength of hard-rock mine pillars. Pillars are found in various shapes and sizes in all underground mining operations. Prudent engineering design requires that if pillars are to perform as desired, both the pillar strength and the pillar stress must be determined. A detailed pillar stability study has been combined with an extensive database of published pillar case histories (178)resulting in a new “hybrid” pillar strength formula, “The Confinement Formula”, that utilizes classic strength of rock methods combined with empirical methods. “The Confinement Formula” utilizes a “mine pillar friction term” calculated from the average minor/major stress ratio with-in the pillar core. Statistically, the new formula provides better results at predicting pillar strength for the combined database than the best empirically ft pillar methods that currently exist. “The Confinement Formula” allows for the determination of the strength of mine pillars with an increased level of confidence over previously applied methods.

Jan 1, 1997

By L. X. Li

Coking coal producers often encounter variations in clean coal quality when mining multiseam deposits containing coals with different washability and coking properties. This paper describes how, for a single coal property, an initial clean coal specification with an ash content of 8.5% on an air-dried basis (ADB) and a free swelling index (FSI) of 5.5 can be improved to a specification with 7.5% ash content ADB and an FSI of 6. This is accomplished by sorting coal seams into two groups for processing and blending. A preliminary economic model demonstrates how this improvement enhances economic returns through a beneficial factor.

Jan 1, 2014

By J. J. Laffin

In the pursuit of comfort and safety, the wonders of science have given us controlled heating and cooling, thus enabling us to enjoy all the aspects of present-day living to an extreme never previously •envisaged. Man's attempt to conquer the elements largely involves con-trolling the temperature around him. Without having conquered this aspect, his body energy would be consumed in trying to maintain physical comfort, rather than being invested in the explorations which have resulted in man's control over the forces of nature. The indirect methods used to obtain the most agreeable temperature environment were developed because of the natural tendency to strive for increased safety, convenience and comfort. Until the twentieth century, when heat generated by atomic fission became a reality, man's only source of heat, except for that of the sun, came from his discovery of fire.

Jan 1, 1962

By V. Gangrade

Recirculation is the major concern associated with the utilization of booster fans. In controlled recirculation, a portion of the return air is purposely mixed with the intake air and the mixture is directed towards a working district, while the air quantity and gas concentrations in the air are closely monitored and managed. The objectives of this study were to determine the gas concentration in intake and return airways during controlled recirculation, and to determine the recirculation fraction for multiple headings. Experiments were conducted in a laboratory model to determine the effect of controlled recirculation on the quality of air circulated through the working faces. Preliminary results showed that recirculation is beneficial to ventilation planning because it reduces the build-up of air contaminants at the working faces and reduces the overall power consumptions. The experimental results were used to quantify the recirculation fraction and to calibrate ventilation models of the laboratory model. These models are used to simulate the controlled recirculation and to predict the gas concentrations in multiple headings.

Aug 1, 2013

By A G. Rogers

This paper discusses the lubrication of surface and underground mining machinery and equipment from the standpoint of machine components. The machine components considered are bearings, cylinders, gears, chains, couplings, fluid drives, hydraulic systems, screws and wire ropes. The best selection of lubricants for these machine components, and for sub-divisions of the components, are outlined. They form general recommendations, for average operating conditions in both surface and under-ground mining operations. The American Petroleum Institute&apos;s service classification of both engine crankcase oils and gear oils is de-scribed and used in recommending products for these applications. The practical aspect of lubrication is kept foremost in the recommendations, which are designed to meet the requirements of a wide variety of equipment with the minimum number of lubricants. THE lubrication of mining machinery and equipment presents a variety of problems peculiar to the industry. The type of mine, the ambient temperature, water, dust, and operating and maintenance practices, as well as the age and condition of the equipment, are variables which have to be considered in making lubricant recommendations.

Jan 1, 1963

By Herbert D. Drechsler, James B. Stephenson

"AbstractThe paper identifies the major components of price change which affect the determination of the internal rate of return of a mining project. It illustrates several price indexes which may be used to measure general price increases, identifying techniques which might incorporate them into mine valuation procedures. The ""hurdle rate"" for new investment is discussed.IntroductionDECISIONS regarding the value of an orebody and whether or when to mine an orebody are based on an estimate of the cash flows which would be associated with its exploitation. These pro-forma cash flows represent cash in or out of a possible mineable deposit and include exploration and construction costs, sales revenues, operating expenses, taxes, debt borrowings, interest and debt repayment. It has long been recognized that when combining the cash flows occurring over the life of the mine, dollars received or paid out early have greater value than those received or paid out later. This time value of money has been incorporated into mine evaluation calculations through the use of present-value or discounting techniques. Another factor affecting mine valuation, inflation, is not accounted for by valuation techniques now in use. In recent years, price changes have become more volatile. In the past, price change could easily be ignored when evaluating potential mines. Today, the combination of larger investments and greater price volatility leads to great concern about the effects of price change on mine valuation."

Jan 1, 1977