Search Documents

By W. B. Coker

A helicopter-mounted lake-sediment and lake-water survey was carried out over Grenville rooks in the Renfrew area (parts of Renfrew and Lanark counties) during four days of October, 1975. In the course of this survey. 1150 square kilometers were covered, with 246 lake-sediment and 276 lake -water samples collected from every body of water on which the helicopter could land. Sample sites, which averaged one per 4.6 square kilometers, included lakes, ponds, beaver ponds, swamps and marshes. Lake-sediment samples were taken using a G.S.C. sampler. Waters were collected directly into polyethylene bottles. At each sample site , surface and bottom-water pH, dissolved oxygen content, conductivity and temperature were measured using a Martel. Water Quality Analyzer. The lake sediments were air dried and then ball milled to pass a minus 80-mesh sieve. Lake sediments were analyzed for U by delayed neutron activation and for Mo, Cu, Zn, Pb, Fe, Mn, Ni and Co by atomic absorption techniques. The organic content of the sediments was determined by loss on ignition at 450 °C. Lake waters were acidified with nitric acid on the day of collection. The U content of the water s was determined by fluorometry; the Cu, Zn, Pb, Fe, Mn , Ni and Co contents of the waters were determined by solvent extraction - atomic absorption techniques. A close relationship was found between bodies of granitic, syenitic and pegmatitic bedrock and elevated U levels in the lake sediments. The Hurd Lake and White Lake granitic intrusive were encompassed by an annulus of higher U activity. Field inspection revealed that the U concentrations occur within a zone which may represent a contact metamorphic aureole. Within these complexes, anomalous concentrations of U appear to be associated with Mo. Information derived from the lake-water data reinforces the geochemical distributions outlined by the lake-sediment survey . This survey was carried out in order to develop optimum sampling and analytical procedures for geochemical reconnaissance of the Grenville Province that may be carried out under the auspices of the Uranium Reconnaissance Program.

Jan 1, 1977

By J. P. Piguet, A. Hosni, J. P. Josien, H. Baroudi, R. Hadadou

"The iron ore mines in the Lorraine region of north-eastern France cover a surface area of approximately 3,900 km2 and involve more than 150 cities. A total extraction method was usually used during exploitation, but this technique was sometimes replaced by the room and abandoned pillar technique when it was necessary to protect surface buildings and infrastructure. Rooms and abandoned pillars were initially designed to ensure long-term mine stability. However, this aim was not always reached and numerous collapses occurred in the Lorraine iron basin, either during production or several years after closure. Several subsidence events were identified during a period of one century; the most recent event occurred in 2012. Two groups of events were identified. The first group represents events characterized by sudden surface movement, and the second group includes event characterized by progressive subsidence.Numerous studies conducted during the last decade helped improve our understanding the origin mechanism of spontaneous or progressive (slow) events. These studies led to identifying long-term potentially unstable underground zones (hazard zones), particularly deep zones located under buildings and infrastructure. The latest are currently monitored by microseismic networks. A similar high requirement level is needed for unstable zones without taking into account the kinetics of the subsidence, which is very important for safety. Thus, GEODERIS initiated this study, primarily to acquire a better understanding of the kinetics of the progressive events group and identify the main parameters that could explain why some pillars zones developed a maximum amplitude subsidence on surface within a few hours or days, while it took several weeks to months for others. In practice, the results of this study will facilitate adapting the requirement level of microseismic monitoring system to the kinetics of pillar collapse.To retrieve the real kinetics for each event, historical and sparse documentation was used. Firstly, archives research was conducted, especially testimonies and newspaper articles published during the events. This work helped to gather useful information that sometimes contained a precise description of subsidence duration. The archives research helped to classify some progressive events according to the subsidence kinetics. Secondly, a diagnostic of geotechnical and geomechanical parameters of historic events was realized, combined with a cross analysis of the data. The analysis took into account dimensions of underground workings (e.g., pillar lengths, widths, heights, introduction of a “pillar shape factor”, and stress amount). An original expression was highlighted to connect the pillar geometry to the stress state. The kinetics expression was calibrated to classify the historic events taken into account according to the kinetics of movements. The kinetic criterion was applied to predict subsidence kinetics for the potential unstable zones currently monitored by a microseismic system."

Jan 1, 2015

By J. Doucet, C. Price

In an industrial setting, operational changes are continually introduced, driven by new technologies or changing economics. Because of day-to-day variability, quantifying the impact of these changes based on metallurgical performance requires long trial periods to achieve statistically significant results. Tools and techniques developed by the mineral processing group at McGill University have allowed for direct measurement of process variables (e.g., bubble size, gas and solid holdup). Two case studies are described where direct measurement techniques were used to evaluate: a) a new rotor stator mechanism; and b ), the introduction of a new frother type. Application of these methods has accelerated the evaluation of process changes and improved confidence in results.

Jan 1, 2009

By R. D. Brown

"Finance Minister Donald Macdonald's budget of May 25, 1976 featured a restructuring of the anti-inflation profit controls and a grab bag of tax changes, some of direct interest to the mining industry. All Canadian taxpayers now will be permitted to write off immediately 100% of mineral and oil and gas exploration expenses included after• May 25, 1976 and before July 1 1979. The cost of acquitting Canadian resource property after May 6, 197.4 from a federal or provincial government will now clearly be included in Canadian development expense, and provincial drilling and exploration incentives received after May 25, 1976 will not reduce exploration and development expense for federal income tax purposes. Under tough new anti-inflation profit controls, all controlled businesses, except distributions, will essentially have one uniform set of rules for• determining allowable profit margins; this allowable margin will be determined by product line or by over-all net margin and will be 85% of the higher of the margin obtained in the five years preceding October• 13, 1975 or the one year preceding May 1, 1976. The basic capital cost allowance system is to continue, but many rates will be revised. The ability to offset losses created through claiming capital cost allowances on leased equipment, etc. against other income will be ended with respect to transactions entered into a/te1• budget night. Miscellaneous other tax changes will raise the low rate base for Canadian-controlled private corporations to $750,000 increase retitement plan contribution limits and reduce the rate of branch tax imposed on branches of corporations resident in a country with which Canada has a comprehensive tax treaty to equal the withholding tax rate on dividends under that treaty."

Jan 1, 1976

By M. E. Grimes

"The future of the uranium industry in Canada during the next twenty years will be very dependent on political and social issues on a world scale. Technology, as such, will tend to be of lesser importance. Nonetheless, some technical changes can be anticipated.This paper deals with milling of uranium ore, leaving further processing and nuclear power production to specialists in these fields. An attempt has been made to look at uranium production technology in Canada in relation to that in other countries, and to draw interference regarding future changes that seem probable in the Canadian context. In particular, recent advances in mill equipment are considered.The chemistry of uranium and its relatively low concentration in most ores has been responsible for a completely hydrometallurgical approach to mill processing, and this should continue. In spite of little commercial success to date, pre-concentration of lower grade ores will be researched further in order that these ores can compete with higher grade deposits in Canada.The discovery of the relatively high-grade ores of the Athabasksa region will undoubtedly influence choice of mill processes and equipment. The potential effect on innovations is discussed"

Jan 1, 1986

By Edgar Dernedde

Cryolitic melts at a temperature of about 960 °C are used in reduction cells to dissolve alumina and to produce primary aluminium. At these temperatures cryolitic melts with an acidic composition have a significant vapour pressure, which contributes substantially to the evolution of fluorides from these cells, The Antoine equation is commonly used for relating vapour pressure data of liquids at different temperatures, It is also applicable to cryolitic melts, Published equations have at least 20 numerical constants, in order to allow for the effects of melt composition. In the present work a simplified equation with only 12 numerical constants was developed and is applicable for multiple additions to molten cryolite up to 30 wt %, The simplified equation was compared with the published equations of Haupin & Kvande and Gustaysen & Ostvold using 472 vapour pressure data of cryolitic melts. Results showed that the simplified equation has the same accuracy as the published equations in the composition range of interest to industry.

Jan 1, 2004

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By Charles Amoah

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By A. B. Walker

The effects of the injection of dry limestone additives into boilers for the sorption of sulphur dioxide have been studied in pilot and full-scale systems. The effects of such injections on boiler mass particulate emissions as well as collectability characteristics of the fly ash and reaction products are presented. Implications of the effects on the design and economics of particulate collectors, in particular electrostatic precipitators, are discussed.

Jan 1, 1971

By G. Morin, F. Chiesa, B. Duchesne

The Quality index is a useful tool allowing to assess the metallurgical quality of aluminium AlSiMg foundry alloys (A356/357). Its value is calculated from the ultimate tensile strength and elongation; it increases with the metallurgical quality of the casting, i.e. with finer dendrites, lower microporosity and inclusion count and lower iron content. This Quality index does not depend on the degree of temper applied during the heat treatment (aging time and temperature). After defining the Quality index, it will be explained how it can be predicted from the knowledge of the local solidification conditions obtained from modelling. The paper will then present four case studies of castings for which the prediction of the Quality index by modelling was made. These case studies from different authors will involve the three most common casting processes used for producing high integrity aluminium castings, namely: sand casting, permanent mould casting and investment casting (lost wax). In all cases, the accuracy of the prediction will be assessed by comparing the predicted Quality index distributions to the experimental values based on the published measured values of the local tensile properties.

Jan 1, 2006

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By M MacMillan

THE following is a brief description of the method of hoisting ore automatically at the No. 14 shaft of Mcintyre Porcupine Mines, Limited, Schumacher, Ontario. All ore and waste below the 3875-ft. level is hoisted up No. 14 shaft from the 7000-ft. level to the 3000-ft. level. Seventy to seventy-five per cent of the mining is done in this area. The shaft consists of four compartments: a man way, a ventilation compartment and two skip compartments. The hoist, located on the 3500-ft. level (see Figure l), is an 80-in.-diameter, 4-rope friction winder, utilizing two 6-ton front-dump skips in balance. The hoist is powered by a 1,100-h.p. A.C. motor, the maxi-mum speed being 2,400 ft. per minute. The operation can be either manual, push-button automatic from the pocket, or fully automatic. Men can be raised or lowered in the skips, using a collapsible aluminum platform placed inside the skip box.

Jan 1, 1963

By Nav Dhadli

Tailings from Oil Sands MiningWhat are they? Challenges Solutions Regulatory Environment Definition of the AFD Tailings Treatment Process 2010 AFD Pilot/Demonstration ProgramTechnical challenges Performance and Results Next steps Oil Sands Industry Collaboration on Tailings Technology TAILINGS ?WHAT ARE THEY? Mixture of remaining water and solids following bitumen extraction process Composed of water, sand, silt, clay, small amounts of hydrocarbon (bitumen, solvent, and asphaltenes) A necessary part of production in excavation of oil sands and removal of bitumen

May 1, 2011

By Michael W. Hinds

X-ray Fluorescence Spectrometry (XRF) is used at various stages of gold refining. Initially, incoming impure gold is analysed for deleterious elements such as As, Cd, Hg, Se, and Te. Based on the levels of these impurities the material can be returned to the client or accepted for refining. XRF is also used to determine the metal concentrations after the impure gold has been melted and sampled. This information is used to assist the final Fire Assay determination of gold and silver. An energy dispersive XRF is used to determine the end point of chlorination refining step.

Jan 1, 2011

By G. G. W. Thom, A. A. F. Schuldt

At The Steel Company of Canada, Limited, iron oxide dust from the basic oxygen open hearths is being collected by means of electrostatic precipitators. The utilization of this dust, which has been hampered by the presence of zinc and lead oxides and sulphur compounds, is made possible by direct reduction in a rotary kiln. The description of the dust collection system and the results of kiln tests are presented.

Jan 1, 1966

By R. ZapataN.

"In the following report, Altonorte Smelter owned by Xstrata will explain its experience with its denominated furnace called ""Continuous Altonorte Reactor"" since started up in March 2002. The Reactor is the main and only smelting furnace since the operation of Reverb Furnace was stopped (15 days after the start up of the Reactor) and it can be operate with dry concentrate for injection by tuyere and wet concentrated via Garr Gun when the injection system fails. From the started up of the Reactor, three operational campaigns have been carried out where in each one they have been increased their smelting throughput and availability. The flexibility reached by the technology bath smelting has allowed a high level of smelting of concentrate and revert materials. The high availability of the Reactor and overcoming problems that were considered of high complexity like the extraction of white metal and slag, refractory campaign, etc. has allowed the Altonorte smelter to project to smelting 1,200,000 tonnes per year with its only Reactor in next year."

Jan 1, 2007

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

By B. R. Bowerman, W. J. Thoburn, M. J. Humphris

"Nickel granules are produced for carbonylation by pouring a molten stream into a path of high pressure water. Granules and water are separated in dewatering bins. The overflow, which contains up to 0.1 weight percent solids, was initially cooled and recycled to the granulating step. However, the rate of buildup of these solids in the handling system was intolerable. A lamella thickener was installed to solve the problem by removing solids from the dewatering bin overflow. Its description, application and performance to date are discussed.The lamella thickener treats a slurry containing about 0.1% solids of which about 30 weight percent is less than 325 mesh. It recovers 80 to 90 percent of the input solids in an underflow slurry containing 90 weight percent solids. Since its installation the frequency of cleanout of the recycle water handling system has dropped from about once per month to about once or twice per-year."

Jan 1, 1977

By P. Clinton Milne

Uranium mines in Washington State include the producing Midnite and Sherwood mines and several mined-out deposits, the most productive of which was the Daybreak mine. The Midnite mine is generally classified as a hydrothermal deposit consisting of tabular orebodies in Precambrian pelitic and calcareous metasedimentary host rocks. The host rocks occur as roof pendants in a Cretaceous porphyritic quartz monzonite intrusive; the quartz monzonite averages 12 ppm U308 The uranium deposit appears to have undergone a complex genesis, involving a series of depositional and enrichment stages. The Sherwood uranium deposit, approximately 4 miles south of the Midnite mine, occurs near the bottom of a basal Late Cretaceous to Paleocene arkosic conglomerate. The conglomerate lies nonconformably on the porphyritic quartz monzonite that is associated with the Midnite deposit. The Sherwood and Midnite uranium deposits may have had a similar genetic history linked by a common uraniferous pluton source, ground-water action, and/or leaching of uranium-rich ash flows from now-eroded, overlying, Eocene volcanics. The Daybreak deposit, in northeastern Spokane County, consists entirely of secondary uranium mineralization (metaautunite) in a quartz monzonite pluton. Mineralization is confined to a low-angle fault zone and is most highly concentrated at the intersection of primary and secondary shears. Both hydrothermal and ground-water origins are feasible. Besides the Midnite-Sherwood area, 14 other areas in the western Okanogan Highlands physiographic province and Cascades region have favourable characteristics for uranium potential. Criteria include the existence of uranium occurrences, Tertiary basin sediments with intercalated volcanic and volcaniclastic rocks, favourable geochemical data, alkaline plutons associated with uranium occurrences or borders of Tertiary basins, and structural controls.

Jan 1, 1979

By S. Kaiman

This paper describes flotation test work conducted over the past several years at the Mines Branch, Ottawa, on the radioactive quartz-pebble conglomerate ores of the Elliot Lake area of Ontario. The purpose of this work has been to produce a uranium flotation concentrate for sub-sequent leaching operations. The results of earlier investigations are summarized and correlated with the results of mineralogical studies of the ores and flotation products. The results of recent pilot-plant investigations by flotation, as well as by gravity concentration followed by flotation of the gravity tailings, are given. The principal collector used for uranium flotation was a tall oil fatty acid, and the indicated total cost of all reagents ranged from 21 to 31 cents per ton of ore treated.

Jan 1, 1966