Search Documents

By T. V. Lord

Minerals containing uranium have been successfully pre-concentrated by flotation at Queen's University, Kingston. In particular, uraninite, uranothorite, euxenite, and fergusonite, have responded to flotation to yield grades of 0.2 to 6.0 .per cent U .o. with recoveries of 85 to 98 per cent, from heads analysing approximately 0.10 per cent U3Os. Of the ten or so radioactive samples examined to date, two distinct groups were recognizable, firstly, those samples in which uranium was the sole constituent of economic interest, and, secondly, those in which Columbium (with minor amount of tantalum) was present in addition to uranium. For the purpose of this paper, the results of investigation on two samples of each of the above groups have been selected as typical.

Jan 1, 1945

"In developing a backfill system handling tailings feed to and from the storage silo, it is necessary to establish a slurry laboratory to develop the technology and silo design criteria. This paper presents the principles involved in such development and the importance of testing principles for optimizing the slurry system. Evaluation procedure based on experiments is applicable to a wide range of materials and allows silo design by scaling up the data gained from model tests. Silo simulation has been successful to design and operation, so becomes an effective approach to backfill applications. IntroductionThe silo is a device comprising specialized equipment and operating with related procedures for storing and handling the mill rejects as backfill slurry. It provides a steady supply of the solids slurry, prepared at desired pulp density under the continuous feed conditions. Because the silo system is designed to accomplish specific objectives when dealing with a particular mill tailings slurry, it is necessary to characterize certain slurry properties, behaviour of the solids slurry and understand the silo performance to establish design criteria. Bench-scale, pilot-scale and dewafull- scale experiments were employed in developing the load-storage-discharge system, and routine procedures are now available for pre-design testing. Silo model experiments and full-scale tests were conducted to define the design parameters and evaluate the silo performance. A silo can be designed by scaling up the silo model geometry and data obtained during tests.Since the early 1960s, silo backfill systems have been widely established. The shape and size of the silo and the operation procedure, as practised, all appear to be relevant to successful operation. Understanding the basic material properties and behaviour of solids slurry retained in the silo will help perfect the silo design, operation procedure and, consequently, improve the silo performance."

Jan 1, 1997

By J. Paquin, P. Doiron, G. Proulx, P. Champoux

After nine years on a 36 hour schedule and two programs of creeping, the Alcoa Deschambault Potroom of faced the necessity of changing its organization for many reasons: the anodes butts were too small, the anode schedule was unbalanced, the iron content in the metal trends had increased, the metal tapping volume did not convene with crucible capacity and the liquid measurement task was delayed by tapping activities. A kaizen activity inspired the Potroom department to improve the organization. A team of 15 people including the process engineer, the process technician, team supervisors and Potroom operators developed a scenario, which would permit flexibility to creep pots if energy is available and an increase of added value production.This paper will describe the systematic approach, the communication method, the trials, the changes, and our success, along with the problems experienced by the team during the adaptation of Alcoa Deschambault Potroom organization over a 20 month period. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By P. -Q. Wu

A modified electrochemical noise (EN) technique has been applied to monitor corrosion wear of TiN-coated ASP23 steel and TiN-coated AISI 316 stainless steel sliding against corundum in 0.5 M H2SO4. Experimental results show that the EN technique can sensitively detect potential and current variations during a corrosion-wear process. Corrosion-wear mechanisms of TiN coatings depend on their substrate properties. If the substrate is passive, such as AISI 316 stainless steel, the potential and current variations reflect the properties of the coating. Depassivation and repassivation alternately take place on the tribo-activated wear area during the steady-state phase. If the substrate is active, such as ASP23 tool steel, the electrochemical noise is dominated by dissolution of the substrate at the pinholes and the hydrogen evolution all over the exposed surface.

Jan 1, 2005

By Curtin University Western Australian School Mines

"Curtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc.) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The model structure, modelling approach, and some scenarios are discussed.INTRODUCTIONCurtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. The model has recently been upgraded to include an integrated liberation-leach modelling (ILLM) approach. The ILLM approach provides the means to evaluate the impact of the gravity recoverable gold (GRG) characteristics of the ore (GRG content and liberation behaviour), various process parameters (such as grind size, bleed to gravity, etc.) and circuit configurations on the gravity gold recovery, leachadsorption circuit behaviour and overall plant gold recovery.A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach. The data required for the ILLM calibration can be obtained directly from the 3 stage GRG test, leach tests and size-by-assay analysis of the 3 stage GRG test products, and leach test products.This paper describes the ore characterisation methodology, model structure, modelling approach, and the application of the ILLM."

Jan 1, 2016

By A. Jordens, Y. Zhiyong

"IMBSRE, one of the largest rare earth element (REE) producers in China, produces a rare earth oxide (REO) concentrate as a by-product by floating the middlings stream from a low intensity magnetic separation step in the main iron ore processing stage. As the mine depth has increased, flowsheet changes in the main iron ore circuit have reduced the REO grade and increased the magnetite to REO ratio in the middling product used as flotation feed for the REO circuit. Extensive laboratory work was carried out and identified a new modified hydroxamic acid product, Florrea 8920, that could provide better metallurgical results over the standard hydroxamic acid used as the main collector. This paper briefly reviews the use of hydroxamates in the flotation of oxide minerals, provides detailed information on the different hydroxamates available from Florrea and then provides a case study of the successful implementation of the Florrea 8920 product in a commercial Chinese REE flotation plant. The case study consists of a one year program of pilot plant testing and industrial trials to confirm the results of laboratory tests. The implementation of the new collector resulted in an improvement in grade and recovery to 61% and 64% respectively. The new collector also provided significant economic and environmental benefits.INTRODUCTIONThe flotation of rare earth element (REE) bearing minerals is a topic which has been dominated in the English language literature by the work conducted on the Mountain Pass bastnäsite deposit (Pradip, 1981; Fuerstenau, Pradip, Khan, & Raghavan, 1982; Pradip & Fuerstenau, 1983, 1985, 2013; Fuerstenau & Pradip, 1991; Fuerstenau, Pradip, & Herrera-Urbina, 1992; Herrera-Urbina, Pradip, & Fuerstenau, 2013). By far the most important collector type used for the flotation of rare earth minerals (REM) is hydroxamates. These reagents were initially extensively described as REM collectors in the English literature by Pradip (1981) however they have been successfully applied to numerous other minerals such as: cassiterite (Sreenivas & Padmanabhan, 2002); pyrochlore (Gibson, Kelebek, Aghamirian, & Yu, 2015); hematite, chrysocolla, rhodonite, hubnerite and pyrolusite (Fuerstenau, 2005); and malachite (Lenormand, Salman, & Yoon, 1979) amongst others."

Jan 1, 2016

By F. Urekar, R. B. Pankhurst

"Air spaces and air gaps in an explosives column are known to allow greater distribution and cushioning of explosive energy from the rock mass. This energy distribution is enhanced if the explosives ' gases can be confined in the borehole for as long as possible by plugging and stemming above the air space.Power Plug is an inflatable plug which can seal a borehole at any point to separate the stemming from an air gap and explosive toe load.IntroductionThis paper will discussion-going work by C-I -L Inc. and operators of two open pit mines to study the results of using Power Plugs:I. Pit wall stability - the authors have found the Power Plug effective for wall control blasting in open pit mines.2. Selective mining of coal seams - the authors work shows the Power Plug allows mining selective coal seams by predrilling underseam waste wedges.Pit Wall StabilityWall stability in an open pit mine is essential for safety. Good wall stability can be achieved with wall control blasting techniques which cushion the effect s of the explosives charge by decoupling the charges from the borehole wall. The usual method of decoupling a charge in a large-diameter rotary borehole is to load the explosives in tubes (Fig .I) . We now believe the air deck system is effective in sea ling a borehole above the explosive charge to create an air deck within the borehole which will cushion the blast.In a linear decoupled charge, an air annulus surrounds the explosives charge and cushions the effects of detonation genera ted gases on the pit wall. In an air deck, i.e. with the hole plugged at the collar, the gases genera ted by an explosive toe load are sealed in the empty borehole column. After a period of time, these trapped gases produce radial cracking between holes along the entire length of the borehole.It is common practice to employ de coupled explosive charge columns in the borehole to limit blast damage to surrounding rock. The exact mechanism of energy transfer in such blasts, however, is not well understood. Interruption of the continuous explosive column in a borehole by means of stemming, or air decks, may also be viewed as another form of decoupled blast. Decoupling of the explosive charge from the borehole wall affects both explosive energy release and explosion pressure developed in the borehole."

Jan 1, 1988

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard:soft (silicate:chromite) and coarse:fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG milling. Preliminary modelling and simulation for the multi-component AG mill model are also included.

Jan 1, 2012

By H. Miki, S. Wheatley

The addition of precipitated silica greatly enhances chalcopyrite leaching in the presence of sodium chloride at moderate temperatures (65-90°C) in acid media with ferric ions as the oxidant. The beneficial effect increases with the increase in chloride concentration and temperature. The addition of sodium silicate and silica sand has no significant influence. The analysis of solubility data in acid/salt solutions indicates that the solubility of silica as Si(OH)4 as the dissolved species is controlled by the activity of water, as expected from the hydration theory. Kinetic analysis shows the trends that copper dissolution from chalcopyrite in the presence of precipitated silica with sodium chloride follows a shrinking sphere model indicating a chemically controlled surface reaction. The effect of temperature on copper dissolution in the presence of both precipitated silica and sodium chloride was also larger compared to the results in sodium chloride alone. The SEM analysis shows that chloride and silica facilitates the precipitation of sulfur on the surface of the silica particles rather than the chalcopyrite particles which avoids the blockage of the mineral surface and thus improves the leaching kinetics.

Jan 1, 2014

By C. A. Morais, L. V. Resende

"The technological development observed in recent years has stimulated the application of rare earth (RE) elements. Amongst their various applications it is well worth mentioning their use in electronics, superconductors, nuclear medicine, as well as in special inks - as those used in radar invisible airplanes. TV and computer monitor screens present as coating a powder containing some rare earth elements, mainly Europium and Yttrium. The recovery of the RE elements from electronic scrap is extremely important as the economic and environmental issues are concerned. This paper describes the study of the Eu and Y recovery from e-scraps. The first step of the process was the leaching of the powder obtained by manually scraping the inside surface of the screen. After the optimization of the leaching, the dissolution of Eu and Y was higher than 98 w/t% and a pregnant sulfuric liquor containing 11.9 g L-1 Y and 0.72 g L-1 Eu was obtained. The second step was the separation of the metals found in the liquor by the solvent extraction technique. The separation of Eu and Y was carried out in a counter current circuit compound of 3 extraction stages, 7 scrubbing stages and 15 stripping stages. DEHPA was used as the extractant, whereas a diluted sulfuric acid solution was applied as scrubbing agent and a hydrochloric acid solution at high concentration was used as the stripping agent.INTRODUCTIONThe rare earths (RE) are a moderately abundant group of 17 elements composed of lanthanides, scandium and yttrium. Amongst the RE, promethium (Pm) is extremely rare, however several of the RE elements are not very rare and occur dispersed in a variety of forms (Greenwood & Earnshaw, 1984; Tyler, 2004).The innumerable applications of the RE elements are based on their particular properties, mainly their spectroscopic and magnetic properties (Martins & Isolani, 2005). The technological development observed in recent years has stimulated the application of rare earth (RE) elements. They have been used in agriculture, electronics, superconductors, nuclear medicine, automobile industry, special inks – as those used in radar invisible airplanes, X-ray screens, high intensity mercury vapour light bulbs, neutron scintilators, charged-particle detectors and optical memory reading systems (Maestro & Huguenin, 1995; Nagaosa & Binghua, 1997; Sánchez et al., 1999)."

Jan 1, 2012

By Rashid Bashir

Shaft sinking through solid rock, which contains little or no water, poses little difficulty. However, when loose, water-bearing strata have to be contended with, water control measures, and pumping facilities are needed. Shaft sinking in Athabasca Basin requires sinking through water bearing sandstone which can be highly fractured. Intersection of local zones of extensive fracturing results in the potential for high water inflows with pressures up to 5 Mpa. Grouting is carried out ahead of each shaft sinking interval as water control strategy. In the grouting method, liquid cement is forced into the water-bearing earth under very high pressure. Shaft sinking performance which can be quantified in terms of rate of advance is highly dependent on the days spent at each interval grouting before sinking can advance to the next interval. This paper presents the shaft sinking experience in Athabasca basin and how some of this is translated into Geoscientific Investigations for Future Shafts. A comparison of Geoscientific data collected from future shafts at McArthur River and Millennium Mines is compared to historical data collected from pilot holes, where shafts have already been sunk. The paper concludes with the strategies for better integration of hydrogeological, geotechnical and geophysical data.

Aug 1, 2010

By S. Akhlaghi

In many electronic/optoelectronic devices, interaction between the metal stack and solder is undesirable. If a reaction happens, a nonuniform joint containing spikes and voids is likely to form and as a result the heat dissipation deteriorates significantly, which in turn, leads to the degradation of the bond. In the present work the interaction between Ti/Mo/ Au metallization system, which was sputter deposited on AlN substrates, and Pb-Sn solder was studied by using scanning electron microscopy (SEM). Also, an EDX system was used to trace the changes in chemical composition of the layers after solder tests. The microstructural examinations show that the Ti and Mo layer from the Ti/Mo/ Au metallization system are not impermeable enough and thus Ca from the surface of the substrate moves all the way up to the interface of Au/Mo and forms an intermetallic at the interface, which grows over time.

Jan 1, 2006

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations for the smelting and refining of non-ferrous metals, and it is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate. It is also the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y zinc. Since then, production capacity has increased, and at present, it stands at 240,000 t/y zinc. In this paper, the leaching process and particularly the operation of the jarosite circuit is reviewed, specifying process improvements to treat high iron calcines.INTRODUCTIONTwenty years ago the Electrolytic Zinc Plant in Peñoles was treating high quality zinc concentrates with low concentrations of iron (~7.5 wt.%) and silica (1.8 wt.%). Nowadays the quality of zinc concentrates is poor with a typical iron content of around 11 wt.% and silica at 2.0 wt.%. This has created numerous processing problems in our roast-leach-purification- electrolysis sections. In order to meet customer requirements it is necessary to find processing solutions to assure the operational continuity of the plant. These processing solutions are the focal point of this paper.REVIEW OF THE LEACHING PROCESSThe purpose of the leaching process is to recover the metals, mainly zinc, through a series of extraction stages with sulphuric acid solutions, which progressively increases the zinc dissolution. After the series of acidification stages, the solution, which is rich in iron, is sent to the jarosite circuit to separate zinc from iron (Garcia & Valdez, 1996). The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper. Then this solution is sent to the tank house to feed the electrolytic cells."

Jan 1, 2016

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher productivity rates and a resultant reduction in activity costs. Increased advance rates, by examination of the key components (face preparation and drilling, hole loading and blasting, scaling, mucking and support installation) in the development cycle, and optimizing these processes is a high priority for research in the Canadian mining industry. Support installation time alone is typically 36 to 46% of the total development cycle time. A reduction in support installation time or techniques and alternative scaling strategies could result in significant gains in drift development advance rates. Support Staging and hydroscaling within the drift cycle could offer alternative drift development sequences that could reduce the overall cycle time. MIRARCO?s research into the support and hydroscaling processes for rapid drift development also suggests that there are many other factors (e.g. mine ventilation services) that have a significant impact on the rate of advance. These factors should be considered to promote and manage safe and rapid drift development. Constraints to the rapid drift development processes can only be overcome by sound construction management practices. In other words, the goals of rapid drifting can be achieved by the implementation of contractor-type construction management. This paper examines various constraints and processes affecting rapid drift development and draws attention to other factors affecting safe rapid drift development.

Apr 1, 2005

By S. A. Sadough vanini

In this paper the influence of temperature on the flow behavior and rheological characteristics of an A356 alloy in the semi-solid state using backward extrusion process are studied experimentally and numerically. Simulation process is done by dynamic explicit in ABAQUS software for each forming condition. A cooling slope treatment was employed in order to obtain a non-dendritic microstructure. Experiments were performed in 5 temperatures and 4 different wall thicknesses. In the low forming speeds, liquid fraction had time to escape from solid phase forward the samples? wall. This condition was the main reason for the segregation phenomenon seen in the base and walls. Viscosities were determined using the force-displacement graphs obtained form back-extrusion tests. As observed experimentally, in a constant temperature, increase of shear rate resulted in decrease of alloy viscosity exponentially. Raising the temperature increases the liquid fraction hence reduces the semi-solid alloy viscosity. The results of experimental and simulation are compared and there is a good adaptation.

Oct 1, 2011

By Graeme G. Strathdee

"IntroductionThis paper presents an overview of the industry status, describes current potash industry practices at three mills, and summarizes developments that have taken place since the previous review by Banks (1985).The commodity potash is produced in both New Brunswick and Saskatchewan from the evaporite ore sylvinite. This ore is a mixture of co-crystallized halite, NaCl, and sylvite, KCl, and a minor assortment of silica, carbonate, sulphate, and clay minerals. Carnallite, KMgCl3.6H20, is also dispersed throughout the bedded deposits and can affect the recovery of sylvite for fertilizer and industrial uses.Canada continues to be a principal source of supply of agricultural and industrial potash products. Figure 1 shows the sector performance between 1989 and 1997 in the context of the world supply and demand situation as reported by Prud'homme (1997) of Natural Resources Canada.Potash industry output is traditionally measured as the quantity of potassium nutrient and reported as tonnes ofK20. Mineralogically, the principal form of potash produced in Canada is sylvite, KCl, and 1 nutrient tonne K20 corresponds to approximately 1.64 tonnes of sylvite of agricultural grade, about 95% KCI. In 1997, the Canadian industry milling capacity was 13.4 million metric tons (Mt) ofK20 (22 Mt KCl) while the actual production was 9.0 Mt K20 (14.8 Mt KCl). Worldwide milling capacity in 1997 was 35.9 Mt K20 (58.8 Mt KCl) and global consumption was 25.3 Mt K20 (41.6 Mt KCl). Canadian producers can deliver about 35% of the global demand for potash commodities"

Jan 1, 2000

By J. A. Reid

THE views and observations expressed herein on this old but constantly recurring question are our own, no effort having been made to align them with standard texts. Therefore, while they may find general acceptance amongst fellow engineers, they must stand as personal opinions and as such are open to debate and discussion. In order properly to consider the subject, it should first be 'set in proper perspective. Why are Prospects Examined? Prospects are examined to determine whether they may contain economic concentrations of metals or minerals, the legitimate mining business being run, pretty largely, to make money. Next to food and clothing, modern civilization is based on metals, with which are included in this discussion minerals, oils, and fuels. A constant and increasing demand for the common metals requires the location of replacements for depleted orebodies, while the use and appreciation of new metals brings increasing demand for them. Aluminium is a good example of a metal which has, within recent years, made great progress. Today, we are becoming increasingly aware of magnesium, chromium, tungsten, thallium, and other lesser known, metals.

Jan 1, 1945

By Szilvia Szabo, Jozsef Paulovics, Ljudmilla Bokanyi

"Waste recycling is one of the most important challenges of the XXI century. The recycling of wastes is closely related to and bases on the mineral processing. Many mineral processing techniques and equipment are applied in this field. The principles of the characterisation of wastes and design of technologies is rather similar to the classic mineral processing. Nevertheless, the diversity of the wastes and their complex composition and properties, as well as their environmental impact requires a special approach.Solar elements have sandwich structure of glass substrate and cover, as well as a very thin semiconductor layer. CdTe semi-conductor can be recycled by flotation. Within the RESOLVED (LIFE European Framework) R&D project on the recycling of solar elements the surface properties of pure CdTe semiconductor and pure glass were investigated by the measurements of zeta-potential using Zeta PALS Brookhaven instrument at University of Miskolc. Applied surfactants were: potassium ethyl xanthate; the anionic oxhydryl Aero Promoter 825 or Flotinor SM 35; the cationic Armoflote 43 or Armoflote 64, as well as Hostaflot LET (dithiophosphoric acid diethyl ester) and Hostaflot M91 (mercaptobenothiazole). The tested electrolyte was sodium-silicate. Zeta-measurements were carried out in full pH-range. Interfacial interactions were detected and interpreted. The basic results were verified by the flotation kinetic tests.Finally, the flotation technological experiments were carried out at a semi-technical scale using the real obsolete solar elements. The particle size at the liberation degree of 98% was as fine as below 5 µm. A special flotation cell providing the generation and distribution of very fine air bubbles was built. The pre-concentrate for the manufacturing of the test solar module was performed and transported to the BAM Institute (Berlin), the principal co-ordinator of the Project, and then further to the First Solar (USA) where a new panel was manufactured using recycled semi-conductor."

Jan 1, 2016