Search Documents

By C. Dodds, R. S. Ferrari-John, The University of Nottingham, G. Dimitrakis, J. Katrib, A. R. Batchelor

"Sorting technologies have the potential to reduce energy use in comminution by rejecting uneconomic ore before feed material enters the mill. However, a major challenge for sorting porphyry copper ores is providing a basis of discrimination between valuable and non-valuable fragments, due to their complex mineralogies and textural features. Microwave heating in combination with infra-red detection (MW-IR) has been shown to provide upgraded feedstock for certain ores at bench scale. Selective heating of copper sulphide minerals compared to the gangue leads to an increased thermal response for valuable fragments, providing the basis for sorting.Rapid scale up of MW-IR from bench scale to a 100 t/h continuous pilot plant facility has been facilitated by the design of microwave choking structures to allow continuous operation at industrially meaningful throughputs, whilst meeting health and safety and electromagnetic compliance standards, and the integration of materials handling with electromagnetic systems.Laboratory batch testing on a pilot scale microwave system has been undertaken to investigate the thermal response of copper ores under industrial conditions, at microwave energy inputs up to 1 kWh/t. These results provided the operating window and recommended test conditions for the continuous pilot plant. Sortability curves predicted in the laboratory are in good agreement with separations achieved during continuous pilot plant operations. The potential microwave sortability of a number of ores has been studied, allowing informed decisions to be made about potential ore candidates based on mineralogy. Future development of the technology will be underpinned by the creation and validation of scale up concepts for 1000 t/h operations. Understanding the value proposition for individual sites/applications will be central to unlocking the potential economic and environmental benefits of microwave sorting."

Jan 1, 2016

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement .Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By D. A. Peterson, R. Pakalnis, G. Peter Mah

"Laboratory and trial installations have been completed to determine the potential of composite cable bolt reinforcement in Canadian underground mines. Several prototypes of glass fibre cable bolts have been developed and tested, two of which are currently available to the mining industry. Their evalualtion consisted of lab testing in Canada and the United States, along with trial installations in several underground mines throughout Canada. The objective was to develop a cost competitive composite cable bolt equivalent in strength to that of a 16 mm (Ys in.) diameter steel cable bolt. In addition to achieving equal or superior load carrying characteristics in tension, the glass fibre cables generally experienced an increase in the rate of installation due to their lighter weight. Unlike conventional steel cables, composite cables may be installed within mines which utilize continuous excavation and which require cuttable support. A market analysis of cable bolt usage in Canada has been completed. Glass fibre cable bolts are an effective means of rock reinforcement in mining applications. They prove to be a viable alternative to conventional steel cable bolting. IntroductionCurrent cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to support the surrounding rock mass. Cable bolts are a form of internal support and are generally used as pre-support in open stope and cut-and fill mining methods. They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, are generally less than 20 m (65.6 ft) and are untensioned. A major advantage of cable bolts is that they are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils. This allows relatively long lengths (>20 m, [65.6 ft]) to be installed in areas with limited head room (1.8 m)."

Jan 1, 1994

By K. D. Eng, W. T. Tierney

"During the past century, the development of vehicular transportation has benefitted tremendously from the performance improvement in engines in a situation where low-cost, plentiful fuel supplies were the order of the day. Engine advances were enhanced by and also dictated fuel modification to better adapt the energy source to the power plant.In discussing the several aspects of the change in approach from ""an engine and its fuel to a fuel and its engine"", the authors touch on the following areas:1. Description of an engine concept that provides the needed flexibility in fuel appetite at good efficiency to cope with future requirement s.2. The constraints placed on liquid fuel resource energy utilization efficiency by special engine-required fuel properties and the fuel efficiency of the various engine types available.3. Future vehicle engine fuel sources. This review will put into perspective the problem associated with the net energy available from future fuel sources under extensive research and development at present.4. A brief review of test data to show that fuel-tolerant and fuel-efficient engines are viable and that, in a fuel-resource-limited future, they can be a ""light at the end of the tunnel.""The Texaco Controlled Combustion System (TCCS)The TCCS is a unique means for stratified charge operation of an internal combustion engine in such a manner as to eliminate the requirement for octane or cetane number specification for the fuel. Octane rating is an empirical engine test method that evaluates a gasoline's resistance to spontaneous ignition or ""knock."" Cetane is based on a different engine test, which determines a diesel fuel's ease of spontaneous ignition . High cetane number enhances cold starting and permits high-speed diesel engine operation. As one would expect, the fuels in current use cover a band when the two values, octane and cetane, are plotted against each other."

Jan 1, 1982

By V. K. Karra

"A simplistic algorithm jar simulating the rod or ball mill Bond grindability test applied to ores and minerals is presented. A performance comparison between the present algorithm and a previously published algorithm by Kapurot, modified in this work jar a fair evaluation, is also given. A worked example is furnished jar leading the reader through the various calculations.IntroductionThe Bond grindability test is widely used for the prediction of the power requirement of an industrial grinding mill. The procedures for conducting this test in either a ball or a rod mill are available(1). In the case of a ball mill, batch grind abilities have been correlated to Bond grindabilities to help monitor day-today variations in ore grindability for the purpose of plant control( 2,3). Of special interest is the algorithm presented by Kapur(3) for the simulation of the Bond test. In practice, the test lasts from 6 to 14 cycles (4 to 10 hours). With this algorithm, one can predict the Bond grind ability using information available from only the first two cycles.Sometimes the prepared feed for the grindability test contains too much fines compared to the total product desired at the mesh of grind under consideration. In such a case, the operator separates the fines from the test feed and adds to the remaining coarse fraction an equal amount of fresh feed. This combined feed then forms the feed to the first cycle of the test. In the present work, Kapur's algorithm is modified to include this special case. A new and relatively simpler algorithm is also presented. Statistical equations relating work index to pertinent variables are also given."

Jan 1, 1981

By R. D. Brown

"Concerns over possible additional involvement of governments in Canada's mining industry and its adverse effects on the industry 's growth were a frequent topic of conversation at the recent Annual General Meeting of the CIM.Still painfully fresh in the minds of industry leaders are the disastrous results of the federal/provincial scramble over resource revenues which followed the relatively high metal prices witnessed in 1973/1974. At current metal prices, it is not surprising, then, that a nagging fear persists that these governments may once again restructure tax and other rules to the detriment of the industry and the country.This month, Tax Notes recalls some of the progress which the industry and governments have made in 1979 in the taxation of the resource sector, and urges that higher metal prices be viewed in light of the costly exploration, development and production efforts which will be required for the industry to continue to play its important role in our economy.IntroductionAt the Annual General Meeting of The Canadian Institute of Mining and Metallurgy, held in April, 1980, it was abundantly clear that there is widespread concern in Canada's mining industry that this country's tax regime may once again be blasted by ill winds of change.A stable and more favourable tax climate, as well as higher metal prices and profits, made 1979 almost a golden year for Canadian mining. However, from the tax viewpoint at least, there are some spots on the silver lining as apprehensions grow that the well-heralded battle between federal and provincial governments over oil and gas may spread to the mining sector, with serious damage to the industry and its newfound federal-provincial cooperation."

Jan 1, 1980

By Gary Hawthorn

"Laboratory testing, by Lakefield Research determined that, in spite of the relatively high pyrite content of the Golden Rose (GR) orebody, it would respond well to gravity concentration followed by either direct cyanidation or cyanidation of a flotation concentrate.Economics favoured the former choice which became the adopted process flowsheet.During the latter stage of the feasibility study, the Dekalb 500 tpd copper flotation mill became available in the Highland Valley of British Columbia. This plant was purchased by Emerald Lake Resources, and was moved to the Golden Rose minesite.The crushing and grinding circuit were retained and the original flotation circuit was replaced with a 400 mtd gravity plus cyanidation circuit. The plant commissioning commenced in August 1987, and by early September was processing 300 tpd.HistoryThe Golden Rose Mine was operated by Cominco during the period 1935 to 1941 processing 146000 tons grading DAD oz/t Au at a rate of 110 tpd .The process flowsheet consisted of gravity plus amalgamation followed by cyanidation.Metallurgical TestingThe underground mining areas were below the level of Emerald Lake, and had flooded on abandonment in 1942.Samples for metallurgical testing were collected from exposed faces underground once the mine had been dewateredin 1984.In spite of the anticipated high pyrite content of the ore samples, it was apparent from the success of the previous operation that the pyrite did not interfere with the gold recovery.Laboratory testing, at Lakefield, determined that, from a technical perspective, two metallurgical options existed, as shown in Tables I and 2.Note that the very high pyrite content of the ore precluded the possible direct marketing of concentrate. The process flowsheet, therefore, had to contain a cyanidation circuit for the operation to succeed financially.Although the anticipated metallurgy was excellent with either option, the 2.1 % increase in gold recovery with the gravity plus cyanidation option made this the clear choice."

Jan 1, 1989

By Neil Schofield

"The Pine Creek gold mineralization is associated with saddle reefs and quartz and quartz sulphide veining within the Enterprise Anticline. The anticlinal structure is complex and the mineralization was considered prior to development to be dominantly strata controlled. Gold grades vary up to 160 gin 1.5 m core samples with coefficients of variation in excess of three.The estimation of ore reserves for such a deposit must account for both the geological complexity and the extreme variability of gold grade.This paper describes the structural and variogram analysis of the gold grades and demonstrates the importance of incorporating the geological model in such an analysis. Variogram interpretation is greatly improved and greater insights into the finer geological structure areprovided. Part 2ofthis work presents the application of multigaussian kriging to reserve estimation for deposits with highly variable grade and which consequently demand highly selective mining operations. IntroductionThe Enterprise Gold Mine is situated some 220 km southeast of Darwin in Australia's tropical north. Gold is believed to have been discovered there in 1869 during the construction of the overland telegraph line.From 1894to 1915, some 75 000 ounces of gold were produced from 121 000 tonnes mined mainly by Chinese leaseholders. From 1906 to 1915, government-sponsored drilling led to the sinking of the Enterprise Shaft to 79 m and several drives were developed. Mining ceased because of war.Since late 1980, Goldfields Exploration Pty. Ltd. had explored on several mining tenements near Pine Creek under joint venture with the title holders, Enterprise Mines NL. This work culminated in the development of the current mine which opened on October 29, 1985.Feasibility studies to determine the economic viability of mining were based on ore reserves generated by project geologists using a sectional polygonal approach tuned to the interpreted geological control of the mineralization.The study motivating this two-part paper covers are-estimation of the recoverable reserve s using the geostatistical approach of multigaussian kriging developed at Stanford University, (Verly, 1984)."

Jan 1, 1988

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By J. B. Sabey, V. R. Degner, D. MacGillivray

"Hydrodynamics principals are applied to the design of a natural air ingestion flotation machine for coarse solids applications. Preliminary laboratory test data and subsequent operating plant flotation kinetic performance evaluations are reviewed. INTRODUCTIONThe concentration of potash (sylvite, KCI) from halite and other salts using flotation is well understood and practice a with much success. Reagent schemes and plant circuitry for obtaining the desired product recovery and grade have been established with proven performance. These flotation circuits normally process the medium and finer size particles, less than 30 mesh (600 microns).However, often the potash market trends specifically demand a coarse product size. This emphasis, accompanied by the existing high losses of coarse (+30 mesh) potash in flotation circuits, creates the need for development of a flotation machines specifically designed for coarse potash beneficiation.This technical challenge was undertaken by the WEMCO Research and Development Group. The specific objectives of this flotation machine development program were ( l) to achieve an ""Ultra Coarse Flotation Machine"" capable of adequately suspending and transporting particles in the 4 - 30 mesh (4.75 - 0.6 mm) size range at solids concentrations of 30% or greater and (2) ascertain metallurgical performance of this machine.This paper covers the development (both theoretical and mechanical/ hydrodynamic), the field test program and results, a discussion of applicable flotation kinetics, and conclusions of this ""Coarse Potash Flotation Machine"" development project."

Jan 1, 1986

By Robert B. Parsons

"Considering the traumatic events of Canadian mining taxation of the 1970s, one wonders at the sanity of anybody who tries to predict what the 1980s might hold for the tax structure of the mining industry. Yet, the author agreed to tackle this task when called upon to do so at the annual meeting of the Quebec Metal Mining Association in June. The text of this ""daring"" speech follows.IntroductionI have been asked to play the part of the oracle at Delphi, and to predict what the 1980s might hold for the Canadian mining industry in terms of taxation. To appreciate the challenge of this difficult assignment, try to imagine someone in my position back in 1972 attempting to forecast the balance of the 1970s. I daresay that ten years ago nobody could possibly have conceived of the devastating and casualty-ridden rollercoaster ride that mining taxation actually took in the 70s. Nevertheless, I shall examine the entrails and try to shed some light on what might happen during the balance of this decade as far as mineral taxation is concerned.If one were to retreat deep into history, one would find that taxation generally served one purpose-namely, to raise revenues for the government. More recently, an important second function has emerged: taxation is increasingly being used as a fiscal tool-a tool intended to mould and shape future events in order to accomplish certain economic, social and political objectives. It is these two main forces-the need (or desire) for revenues and the perceived convenience of using taxation as a fiscal tool-which will continue to shape the tax structure of the future.In our assessment of where taxation of the mining industry may be headed, we should be able to learn something by looking at where we have been."

Jan 1, 1982

By Michael L. Free, Zongliang Zhang, Joshua M. Werner

In the copper electrowinning process, short-circuiting between the anodes and the cathodes is a critical problem that changes the current allocation among local electrodes and reduces the current efficiency significantly. Possible reasons for the short-circuiting include the improper alignment of the electrode, bent electrode, and nodules on the cathode surface. In typical tankhouses, there is often a time between shorting and harvesting as well as between shorting and clearing. Therefore, it is inevitable to have short-circuiting affect the operation performance in practical electrowinning operations. However, one key piece of missing data is the actual measurements of the current efficiency as short-circuiting is approached and allowed to continue. Consequently, short-circuiting tests that allow tracking of electrowinning parameters before and after short-circuiting were performed in a laboratory scale Cu electrowinning cell. In the tests, the electrode spacing change, the mass of electrodeposited Cu, the deposition morphology, and the current allocation as well as the current efficiency before and after short-circuiting were studied. Results show that the short- circuiting affects the current allocation and the current efficiency significantly. Moreover, it changes the Cu deposition on the short-circuited cathode and therefore causes problems for Cu electrowinning. INTRODUCTION Electrowinning (EW) is commonly used for copper production around the world, with a rated production from 120,000 to 200,000 tons per year per operation (Wiechmann, Aqueveque, Henríquez, Muñoz, & Morales, 2014). In Cu electrowinning, Cu ions in the electrolyte are reduced on the cathode surface as metallic copper with a DC current, while on the anode, a counter anodic reaction occurs with oxygen gas generation (Werner, Zeng, Free, Zhang, & Cho, 2018; Zhang, Werner, & Free, 2018; Zhang, Werner, & Free, 2018). In copper electrowinning, an average current density of 200 to 400 A/m2 is applied to the electrowinning cell (Wiechmann et al., 2014). As the Cu deposits on the cathode, the distance between anode and cathode reduces and most of the time, short-circuiting forms between some anodes and cathodes in a large tankhouse containing thousands of electrodes, reducing the current efficiency and increasing the energy consumption significantly. The current efficiency in well-run copper EW operations is typically above 90 %. Most of the unused current is wasted through short circuits, stray currents, and by-byproduct formation (Davenport, King, Schlesinger, & Biswas, 2002; Wiechmann, Vidal, Pagliero, & Gonzalez, 2002; Wiechmann, Morales, & Aqueveque, 2010). Usually, in the tankhouse, the short-circuiting increases the current in the involved cathode by up to 1500 A (Wiechmann et al., 2010). Multiple reasons can cause the short-circuiting in the cell, and the most common reasons include the uneven current distribution among cathodes, tilted electrodes, bent electrodes, and nodules formed due to the large deposition roughness. Recognition of this challenge in the Cu electrowinning process has led researchers to perform many investigations on approaches to avoid and reduce the short-circuiting in the cell. A series of research investigations have been conducted to develop and improve a new type of intercell bar for Cu electrowinning (Wiechmann et al., 2002; Wiechmann, Morales, Aqueveque, & Burgos, 2007; Wiechmann, Morales, & Aqueveque, 2009; Wiechmann et al., 2010; Wiechmann et al., 2014). The associated test results show that this new design limits the occurrence and magnitude of short circuits and allows operation at higher current densities. Sandoval, Clayton, Dominguez, Unger, and Robinson (2010) stated several keys to control short circuits, such as maintaining the straightness of the cathode, removing “edge hair” from the cathode starter, and maintaining electrode alignment in the cell. Prengaman and Siegmund (1999) from RSR technologies developed a new Pb-Ca-Sn anode to prevent the anode deformation, thereby reducing the short-circuiting in the Cu electrowinning cell. Although the negative effects of short-circuiting on the Cu electrowinning have been recognized, and various investigations have been conducted to address this issue, the actual measurements of the electrowinning behavior and performance as short-circuiting is approached and allowed to continue are seldom reported. However, in typical tankhouses, there is a time between when shorting occurs and harvesting/clearing are performed. One key factor in determining the harvest time is the frequency of shorting. Consequently, we have performed short-circuiting tests that allow us to track electrowinning parameters before and after short-circuiting.

Jan 1, 2019

By R. B. Stein

"Countercurrent decantation circuits(CCD) are often employed in hydrometallurgy to effect solids-liquid separation in combination with a barren solution wash to reduce losses of valuable solution component(s) from the tails. Bechtel Corporation uses its BEMSIM flowsheet-modelling PC computer program to simulate a CCD circuit where the ""dirty"" wash solution contains significant amounts of soluble components. An algorithm successfully models this condition and is simplified to a single expression when the wash solution is a ""clean"" solution containing no solubles. The CCD calculation module is compared to operating data from uranium and nickel-cobalt CCD circuits.IntroductionHydrometallurgical process schemes have often relied on countercurrent washing methods to reduce soluble losses of valuable product in the tails. Commonly used equipment to effect this operation is a CCD circuit of N thickeners in series, where a slurry is fed to thickener I and a wash solution to thickener N; clear pregnant solution overflows thickener I and washed tails exit as underflow from thickener N. CCD circuits of this type are typically employed when the solids tend to slime heavily and where a filter is not economic.A typical CCD circuit usually employs from two to five thickeners and can employ either a ""clean"" washing solution of, say, pure water or else the hydrometallurgical circuit may generate a ""dirty"" barren solution containing an appreciable amount of soluble component which may be advantageously returned to the process as CCD wash solution. Various authors have treated the case for clean washing solutions (Svarkovsky 1977, Merritt 1970). For the case of dirty wash solutions, an algorithm has been developed to enable efficient modelling by the BEMSIM computer program, because the need for an accurate method to calculate soluble losses is required when performing an economic trade-off analysis of the value of product lost in the tails as a function of the number of thickeners."

Jan 1, 1990

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By T. W. Sullivan

"This paper explores the history of AC static variable frequency control drive systems on open cast mining machinery, in particular electric mining shovels and electric walking draglines, over the past ten years. It critiques the peformance of these drive systems from a productivity and operating cost standpoint and evaluates the over-all success of the original design concepts as they were envisaged in the 1970s. The paper details the state-of-the-art as it exists today as well as design improvements contemplated for the immediate future.IntroductionConsidering the fact that the very first successful application of an alternating current electrical distribution system occurred at the Gold King gold mine near Ames, Colorado, U.S.A., in the year 1891, it seems somewhat ironic that almost 100 years later, AC excavator drive systems are just now becoming commonplace in the mining industry.If one were to read the biography of Lucien L. Nunn, the first person to successfully install a commercially viable alternating current power distribution system, one would quickly visualize a parallelism between his fight to achieve acceptance of his new lower cost technology and that of those commissioned with the belief that AC static variable frequency control drive systems are not only a better performing, lower cost drive system for mining excavators today, but moreover, the drive systems of the future in our industry.This paper will deal with the evolution and incorporation of AC static drive systems on open cast mining excavators. It will trace the history of the development of these drive systems in the mining industry, the current state-of-the-art concerning these systems, and what the future holds for these excavators in our industry."

Jan 1, 1990

"In the first half of 1990, Cambior earned $1104 million, or $0.37 per share, on revenues of$66.4 million. The company's strong cash position, attained late in 1989 and in the beginning of1990 through the exercise of warrants, put working capital at $83.8 million as of June 30, 1990. Long-term debt was reduced by over $10 million during the weak gold market, leaving the company with a debt to equity ratio of only 0.03. Production for the six first months of 1990 was 107 720 oz. Au, an increaseof24% over the corresponding period in 1989.Financial Profile/Results and Corporate Financial StrategiesTotal revenue for the 1989 fiscal year was $116,883,000 compared to $109,848,000 for 1988. The 1989 results achieved despite a lower average gold price, resulted from a higher level of commercial gold production and a 115% increase in investment income over 1988. Investment income rose to $3,568,000 in 1989 due to higher levels of cash assets.Cambior's mine operating costs increased 19% to $68,561,000 in 1989 from $57,472,000 in 1988. This increase resulted from rising operating costs at the Doyon Mine ($250/oz to $274/oz) due to the shift from open pit to underground operations, as well as from the start -up of three new mines with relatively higher costs. These costs have reached a stable level that should be maintained for the next few years.In 1989, net exploration expenses were $6,838,000, down 31070 from 1988, partially due to the Canadian tax reforms introduced since 1987. Depreciation and depletion grew by $1,432,000 in 1989, reflecting a higher volume of commercial production from the Pierre Beauchemin, Lucien C. Beliveau and Chimo mines.Net earnings for 1989 amounted to $17,661,000 or $0.73 per share compared to $17,438,000 or $0.74 per share in 1988.Cambior has an exceptionally liquid and strong balance sheet. As at December 31, 1989, net working capital stood at $85.6 million, with a total assets base of $338.6 million. With a long-term debt (including gold loans) of $21.5 million and shareholders' equity of $277.2 million, Cambior has a debt to equity ratio of 8%. All but about $100,000 of long-term debt is in the form of gold loans.The total market value for Cambior's stock as at September 10, 1990, stands at $420million, based on recent stock market prices. Cambior's stock and warrants are traded on the Montreal and Toronto Stock Exchange."

Jan 1, 1990

By D. Assmus, S. Daly

"Poor fragmentation, high toe areas, excessive shovel wear and tear and frequent re-drilling and blasting of certain tough waste rock zones in the Lomex pit in the early 1980snecessitateda better understanding of these zones.A combination of geotechnical mapping, penetration rate data, toe elevation contouring and observations on shovel and drill performance were used to determine the character and extent of these zones. This complementary information was brought together by the geotechnical mapper and the explosives supervisor.Distinct zones with particular geological characteristics were determined. A classification system with three types of blast and dig-ability was developed for the Lomex pit and later applied to the Valley pit, with considerable success. The three blast zone types are called ""poor"", ""f air"", and ""good"". This system will be described in detail.The explosives supervisor adjusted the blasting parameters to each zone, in particular, pattern spacing and burden. The resulting powder factors showed considerable variation between the poor, fair and good zones within each pit as well as between the two pits. Pattern geometry and length of collar were also adjusted to improve fragmentation. Cost savings resulted from less re-drilling and less wear and tear on drills and shovels in the poor zones and more efficient use of explosives in all the zones. An annual estimated cost savings of well in excess of $1,000,000 is realized at Highland Valley Copper. A by-product of the mapping was the determination of unstable structures and water flowing zones. Blasting was then adapted to this information for enhanced slope stability."

Jan 1, 1992

By Christopher Andreae

"Years before the present iron and steel works were established at Sydney, several thriving although short-lived iron work s operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron work s. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principle fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel work s dominated production for Nova Scotia and the rest of Canada.Two sites achieved prominence in the nineteenth-century Nova Scotia iron industry: Londonderry and Ferrona. Londonderry, the larger and longer-lasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2,600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace, but once the furnace was blown out in 1904, the population gradually drifted away.Early HistoryThe history of Nova Scotia's iron industry began in 1604 when Samuel Champlain became the first European to identify iron ore in the future province. Despite this early acknowledgment, iron was not smelted commercially in Nova Scotia for another two hundred years. Although primitive smelters of the period produced more iron than could be used locally, early settlers depended on imports of iron from Britain and the United States."

Jan 1, 1983

By E. Rosseland

Glencore Nikkelverk is operating its Chlorine Leach Process in Kristiansand, Norway, producing nickel, copper and cobalt metals by electrowinning. The copper tankhouse, with an annual capacity of 40 000 tons, is based on traditional technology with copper starting sheets and cast lead anodes. Due to the integration of this copper sulphate process in a nickel chloride refinery, operating conditions are unique. In recent years, operating costs have escalated, and health, safety and environment are top priorities. Test work on a new copper process involving permanent cathodes was therefore initiated in 2007, and a pilot plant was started up in 2012. The objective was to introduce innovative technologies and tailor these to be robust in the Nikkelverk process, to form a basis for a new sustainable copper tankhouse with a high degree of automation. Key learnings from more than 10 years of R&D work is presented, focusing on cathode materials and copper metal deposition including product quality, robotic stripping, coated titanium anodes, electrode contacts and alignment, electrode current monitoring with Hatch HELM tracker technology and acid mist capture using cell hoods with off-gas scrubbing. The new copper tankhouse project was approved in December 2018, and commissioning is planned in 2022. INTRODUCTION The Kristiansand nickel refinery was started up in 1910, processing nickel-copper matte originating from Norwegian mines. It was the first industrial plant in the world to produce nickel by electrolysis using the Hybinette electrorefining process. After roasting to burn off sulphur in the matte, copper was leached and recovered as cathodes by electrowinning with lead anodes. In the first years, the copper cathodes were fire- refined and cast into ingots for sale (Thonstad Sandvik, 2004). The Nikkelverk refinery was acquired by Falconbridge Ltd. in 1929, and since then matte from Sudbury, Canada has been the main feed source. The Hybinette process was in operation until 1975 when conversion to the newly developed Chlorine Leach Process was started (Stensholt, Zachariasen, & Lund, 1986). In this process still used today, nickel and part of the copper in the matte is leached using chlorine gas generated on dimensionally stable anodes in the nickel and cobalt electrowinning tankhouses, as illustrated in Figure 1. The presence of dissolved copper ions in the strong chloride leach solution is essential for effective chlorine absorption and nickel dissolution. To improve copper-nickel separation, slurry from the atmospheric leach is pumped to autoclaves and then to cementation tanks for precipitation of copper as copper sulphide, which is collected in filter presses. The leach residue, also containing the precious metals, goes through a 3-stage wash to remove chlorides before being introduced as a slurry to fluid-bed roasters for sulphur removal. The resulting calcine is then leached in spent electrolyte from the copper electrowinning tankhouse, to dissolve most of the copper and also some nickel, cobalt and other elements. After separation of the leach residue, elements like Bi, Te, As and Ag are removed from the strong copper sulphate solution by reaction with metallic copper in three columns in series filled with cut copper cathodes. The purified solution then passes polishing filters before being mixed with spent electrolyte and returned to the electrowinning cells.

Jan 1, 2019

By G. K. Livingstone

"This paper describes mining conditions in the Kaiser surface and underground coal mines in the Sparwood area of southeastern British Columbia. Mining methods are explained, major mining equipment is listed and production rates are given. Reclamation methods and results are described. Data are given on safety organization, safety practices, accident statistics, safety inspections and absenteeism. IntroductionThe coal mines of Kaiser Resources Ltd. are located in the southeast corner of British Columbia. All present mining is in the Sparwood area, where operations began in 1900 with the opening of the Michel underground mines. Production increased rapidly at first, then went through successive periods of depression and prosperity. Following are the highlights. Quantities are in clean, short tons. 1900 1910-Rapid rise in production to a peak of 512,000 tons in 1910.1911-1924-Reduced rate of production, averaging 238,000 tons per year, due to strikes, manpower shortage during World War 1 and post-war depression.1925-1929-Second prosperous era, with production climbing to 383,000 in 1929.1930-1933-Second depression-production falling to 231,000 in 1933.1934-1942-Third era of prosperity-production recovered and new production peak of 908,000 tons reached in 1942 during World War II.1943-1956-Corttinued prosperity, with production averaging 720,000 tons per year.1957-1959-Loss of markets to oil and gas; production dropping to 517,000 tons in 1959.1959-1969-Recovery due to new coal market in Japan; production climbing back to the 900,000-ton level.197D-Present-Jump in production reaching 6.6 million tons in 1975. This was the result of the purchase of the property by Kaiser Steel, who negotiated a large-volume, long-term contract with Japan, built the coal port of Westshore, reduced shipping costs by instituting unit trains, and reduced production costs by investing in large-scale mining machinery and a new preparation plant."

Jan 1, 1980