Search Documents

By A. J. Barry

To determine the torque-load relationship for SIB-inch (nominal)-diameter roof bolts, the Bureau of Mines tested 5 makes of expansion shells and 2 types of bolts (regular and high-strength) in 2 sandstone and 2 shale mine roofs. Unused flat-steel bearing plates in as-received condition were used in these tests. The relationship between torque and load was found to be approximately 50 pounds of load per foot-pound of torque for both the regular and high-strength bolts. This relationship is valid up to 130 foot-pounds for the regular bolts and up to 175 foot-pounds for the high-strength bolts. A torque of 130 foot-pounds on a regular bolt will produce a load of 6,150 ± 1,910 pounds 90 percent of the time, and a torque of 175 foot-pounds on a high-strength bolt will produce 8,050 ± 2,750 pounds 90 percent of the time. Above these values, the torque-load relationship tends to be erratic due to binding between the bolt and plug threads. Binding causes excessive torque to be expended in producing torsion in the bolt rather than tension. This torsion adversely affects the yield load of the bolt. Therefore, the installed torques should not exceed the 130-and l75-foot-pound values. A statistical analysis of the data showed that the torque-load relationship was not significantly affected by the type of bolt or expansion shell unit but might have been affected by the type of rock.

Jan 1, 1956

By D. B. Dow

The transportation of any commodity which is actually or potentially a source of fire or explosion, has been made safe, insofar as humanly possible, by rigid requirements as to inspection mechanical safety devices, and by printed labels. For the most part these precautions have been sufficient. This is evident when it is considered that in the thousands of instances in which commodities with a great fire risk have been transported, few disasters have occurred. This paper deals with the recent gasoline explosion which occurred at Memphis, Tennessee. At 7:50 a.m. January 24, 1921, vapors from a tan: car of gasoline became ignited and resulted in a blast that killed eleven people and badly injured nineteen others. Probably forty or fifty men, women, and children received slight injuries from falling debris or from burns. The explosion wrecked an oil plant, leveled a block of frame buildings, and broke window panes within a radius of five blocks.

Feb 1, 1921

By J. R. Bartels

Operation of underground coal mine mobile equipment is usually done in a restricted workspace with reduced visibility. This work environment puts machine operators in awkward postures for tasks that require awareness of their surroundings and fast reactions to avoid hazardous situations. Using experienced equipment operators as a source, researchers conducted an investigation that developed a method to gather data on the needs and practices of machine operators while controlling the machine and the reasons for needing particular operational cues. The method used was an interview technique including a survey questionnaire and visual aids. The data gathered defined operator cues and work positions for the cutting and tramming phases of remote controlled continuous mining machines used in underground coal mines. Analysis techniques to determine which cues an operator sees from a variety of positions utilizing a computer simulation is shown to be potentially useful to the mining industry for design of work practices and workplace layout and could impact equipment design and selection for improved worker safety. Conclusions indicate that the survey was a good research tool to collect data and helped investigators understand important visual cues. Using this information, researchers were able to analyze the visual cues an operator can see from a given work position and posture.

Jan 1, 2009

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station have shown that the satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but upon the kind of fuel used, and that much of the trouble experienced with permissible flame safety lamps at mines is due to the common use of motor gasolines, none of which is suitable in the present types of permissible flame safety lamps. This report gives the results of a limited study to determine what satisfactory fuels are available, the specification limits of such fuels, and to suggest modifications of assembly and care of the lamps to improve performance with any satisfactory fuel.

Jan 1, 1938

By Daryl E. Radcliffe

This report describes an instrument system developed by the Bureau of Mines to continuously monitor and record changes in roof displacement during underground mining activity. The instrument consists of a single-wire extensometer coupled to a mechanical-drive chart recorder mounted in an aluminum frame installed in the roof. The unit is small and simple to install and meets safety requirements for use in underground coal mines.

Jan 1, 1977

By D. Caruso

The health and financial costs of cumulative injuries are plaguing the mining industry. Industry leaders are concentrating on reducing the risk of injury to their workers through design and redesign of work environments. While ergonomics is not a currently regulated field, many mines are realizing that the only way to tackle their most costly injuries, cumulative injuries, is to make the proactive choice to understand those injuries, their root causes and to make workplace changes to prevent them from occurring. Reduction of these injuries not only improves the health and morale of the workers but increases productivity and profit for the companies. Knowledge and reporting of ergonomic risk factors by employees and ergonomics committees is key to these changes and to the reduction of cumulative injuries. NIOSH is developing strong relationships with industry associations and equipment manufacturers to leverage their communication abilities to transfer knowledge to their customers and make a difference in the health and safety of U.S. miners. The benefits of a formalized approach to reducing these injuries along with examples will be presented.

By John W. Frey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions, which is being prepared in advance of a general re- port relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws governing the Portuguese overseas possessions, prepared from the best avail- able information in Washington, has been slightly amplified in accordance with suggestions transmitted through the courtesy of the Department of State by Fred Morris Dearing, American Minister at Lisbon.

Nov 1, 1929

By W. P. Yant

The hazard to health from contamination of air by a noxious gas depends not only on the potential harmful response attending exposure, but also on the warning properties, which in effect may be termed the "accompanying warning response," This warning may be manifested as an odor, taste, irritation of the eyes, nose, or throat, or perhaps headache, vertigo, or nausea. These manifestations may be painful and even slightly harmful, but to a much lesser degree than the primary injury of exposure. The warning response mitigates hazards directly in proportion to the degree of Intolerability which accompanies injurious exposure, and accordingly its absence augments hazards. This accounts for the fact that the actual health hazards from a non-odorous or non-irritating gas or vapor of comparatively low toxicity sometimes equal or exceed the hazard from a considerably more toxic substance, but one which possesses a marked odor or produces eye, nose, or throat irritation in advance of harmful exposure. When a substance lacks the properties for giving warning, it is often possible to impart them by the addition of a small amount of another substance which has an exceedingly high warning intensity. The vapors of this substance, commonly termed a "warning agent" or "tracer gas," escape and mingle with the gas or vapor which lacks warning properties and thereby apprises persons of the latter's presence. The amount of the warning agent added is that which will give adequate warning in advance of serious physiological harm from the dangerous gas or vapor.

Jan 1, 1930

It is suggested in chapter 1 that emergency activities (including escape) are not individualistic. They tend to be group responses. If escapes from mine fires are group activities, then preparation for such events must take group behavior into account. This chapter explores the hypothesis that the miners who escaped from the three mines under study did so as members of groups. For development of this chapter, the database was examined for evidence of the existence of escape groups and for instances when individualistic behavior was paramount. Illustrations of group and/or individualistic behavior were analyzed and representative examples are provided in the following discussion. The nature of groups was discussed in chapter 3 and the following working definition was offered: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at second-hand, through other people, but face-to-face" [Homans 1950]. To determine whether or not groups existed during the fire evacuations, it is important that the concept of group be clearly defined. Therefore, the discussion started in chapter 3 will be elaborated here. The defining characteristics of group given in chapter 3 were taken from Homans [1950]. They include size, person-to-person com¬munication, feelings that members have for each other, explicit and implicit rules for behavior, and common activities. An additional characteristic that is sometimes used to define groups is cohesiveness. Kiesler and Kiesler [1970] state, "Cohesiveness would include not only the attraction that the group holds for its members but also any other force operating on the individual to stay in the group." Variables said to contribute to cohesiveness include "(1) the attractiveness of a group for its members," and "(2) the coordination of the efforts of the members" [Keisler 1970]. One source of the attraction to a group occurs when "the goals or exterior tasks confronting the group are consistent with those of the individual person, and can best be handled by group action" [Cartwright and Zander 1968, in Davis 1969]. In other words, a common goal and a coordinated effort mounted to achieve that goal contributes toward the creation of a cohesive group. As discussed in the earlier review of research (chapter 1), groups have frequently been studied in laboratory or simulation settings. These methods allowed control over variables of interest. Kiesler and Kiesler [1970] state, however, that they "find group variables conceptually imprecise and experimentally difficult to work with." Experimental control, in other words, is difficult to achieve in the study of groups. The richness of the naturalistic mine fire data may provide an opportunity for an examination of groups that cannot be found in laboratories or simulations because this environment was not

Jan 1, 2000

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By Russell E. Griffin

Dielectric constants and dissipation factors were measured for six rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Results for both dry and moist specimens are presented and compared with data reported by others. Loss factors calculated from the data presented are important to the Bureau's study of rock fragmentation by means of dielectric heating.

Jan 1, 1967

By Paul T. Allsman

THE THREE words, research, mechanization, and automation are keynote words for mining technology during 1962. Basically interrelated, they not only express the major technologic developments in mining but are the signposts pointing out the road ahead. The process represented by each of these words is evolutionary rather than revolutionary, but developments during the past year indicate a climactical stage has been reached in the process of evolution. Mining research has progressed beyond the stage of academic discussion and is a programed activity within the Federal Government,3 the mining colleges,4 and many of the large mining companies.5 Research was a major agenda item at various national and international mining meetings in 1962. A list of these meetings would include such diverse locales as the Workshop and Symposium on Computers and Computer Applications in Mining and Exploration at the University of Arizona in March; and the 5th Rock Mechanics Symposium at the University of Minnesota, in May; the Rock Mechanics Symposium at McGill University, Montreal, Canada, in September; and the Colloquium XIII, International Society for Rock Mechanics, at Salzburg, Austria, in November.

Jan 1, 1963

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By T. J. Ballard

The Tallapoosa Copper mine in Haralson County, Ga., has been operated, or under development at various times since before the Civil War. The geology of the deposit is similar to that of many of the pyrite deposits occurring in the belt of ancient crystalline and metamorphic rocks that extends diagonally northeast-southwest across the State. The Bureau of Mines, in its program of investigation of, strategic mineral deposits, diamond-drilled four holes totaling 1,570.3 feet at the deposit during the period June to September 1947 to verify the old drill records and the continuation of the deposit at depth.

Jan 1, 1948

By E. D. Gardner

Humphreys Gold Corporation of Denver, Colo., was conducting a successful placer operation in 1936 on North Clear Creek about 6 miles below Blackhawk in Gilpin County, Colo. About 3,000 cubic yards of gold-bearing gravel are dug daily (September. 1936) by two draglines and a power shovel. The gravel is screened in a portable washing plant; the trommel oversize is discarded, and the undersize is pumped to a gold-saving plant. The gold is caught in riffles in sluice boxes. The total cost of mining is about 20 cents per cubic yard. The mine is in a narrow canyon at an altitude of 7,200 feet. The Blackhawk-Central City branch of the Colorado & Southern RR. runs over the property. Freight platforms for receiving supplies were moved as the workings advanced. The workmen reached the mine on a speeder that ran on the railroad tracks from a point on the automobile highway (U. S. 40) on Clear Creek near the bottom of Floyd Hill, about 5 miles distant. The mine is 36 miles by road and speeder, or 30 miles by rail, from Denver.

Jan 1, 1937

By Raymond B. Ladoo

The uses of talc are many but are not, in general well known or fully developed within the last decade several companies have realized the possibilities of greatly increased use and have intelligently proceeded to develop some of the fields which seemed most promising. This has had a tendency to lift talc from the obscurity in which it had existed for years, but the work is only started and much remains to be done. Considerably more attention has been paid to the technology and utilization of talc in Germany and Austria than in this country, despite the fact that the United States produces 65 of the world's talc and Germany and Austria combined but 5.4%. In the "Bericht,uber die tatigkeit des verbends der talcum-interessenten in Oesterreich-Ungarn" (Proceedings of the Austro-Hungarian Talc Association), for the years 1912 and 1913, many notes upon new uses appeared, together with suggestions as to further development of old uses. Aside from a few notes on the use of tar in paper, little has been published in the English language upon this subject. By recent action of the Talc and Soapstone Producers Association (U.S.A.) funds for research into the properties and uses of talc have been made Available and it is hoped that markets will be materially broadened a a result of this work.

May 1, 1920

By Roger L. King

The Bureau of Mines has developed probes to be used in emergency mine rescue operations by being lowered through a borehole drilled into an underground mine. Various probes can provide two-way voice communication with trapped miners, continuous mine atmosphere monitoring, temperature indication, and television searching capability. At present, an infrared imaging probe is being developed for "seeing" through coal smoke.

Jan 1, 1976

By R. S. Conti, C. D. Litton

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide(CO) sensors, and a point type heat sensor (PTHS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s. The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS. A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and CO sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity. Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners’ escape.

Jan 1, 1995

By R. L. Handy

The goal of this research was to adapt the highly successful rock borehole shear test for use in deep, small-diameter boreholes. Operating somewhat on the principle of a rock bolt, the borehole shear test measures both the expansion pressure and pulling force to give discrete measures of rock shearing strength as a function of the applied normal pressure. A new instrument was designed and built to fit into a 2-3/8 inch diameter hole. Unfortunately the design became so complicated, the operation is nut reliable. This is attributed to constraints of the small hole, and added requirements of an in-hole anchor to push against, and a rotating shear plate cleaner for repeated tests down-hole. A clue to the d: vice complexity is its length, which is over 10 feet. Furthermore it employs concentric cylinders and one hydraulic cylinder bored into the piston of another, or it would be even longer. Meanwhile drilling technology has advanced to greatly reduce costs of drilling 5- or 6-inch diameter holes. The downhole tester therefore should be redesigned and simplified for use in a larger diameter drill hole.

Jan 1, 1982

By Edward Thomas

In 1947 the Bureau of Mines, as an accident-prevention measure, decided to advocate the adoption of roof bolting (suspension roof supports) in coal mines where it appeared to be applicable. Subsequent experience has disclosed that the applicability of this support is more general than was first suspected; moreover, comparison of the accident records of mines before and after adoption of the roof-bolting method shows results that more than justify the effort and funds expended. The industry has responded enthusiastically, because roof bolting proved to be not only an accident-prevention measure but also one to increase productive efficiency. In some instances this increase in the productivity of men and machines has been almost incredible and has led many mining men to conclude that through some hocus-pocus they can now cast aside many or all of the time-proven rule of good mining practice. If this tendency is not counteracted, it could easily result in an increase of roof-fall accidents, which may outweigh the benefits of roof bolting and discredit an innovation in roof control that shows great promise of materially reducing our mining accidents. From an economic standpoint it may represent the margin between profit and loss in many mining operations. The purpose of this manuscript is not to propose an inflexible code or set of rules but to summarize the experience to date as a guide for those who have the responsibility for the installation and inspection of roof bolts. This experience consists of approximately 250 investigations of roof failure in which roof bolting was involved either directly or indirectly. It should be pointed out that many of these failures were controlled, occurring during experimental periods, and comparatively few of the accidental failures actually resulted in personal injury, yet a significant number represented potential hazards.

Jan 1, 1951