Search Documents

By Terry J. Close

The Anaconda Pintlar Wilderness has a significant mineral resource potential. Five deposits have resources totaling about 180,300 tons (163,600 t) containing silver, copper, lead, gold, and zinc. Another 11, not sufficiently exposed to allow resource estimates, may have additional mineral potential. No placer deposits are indicated. There is little potential for the production of sand, gravel, or stone; alternate sources are closer to markets. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

By W. E. Miller, Kennedy. R. E., G. W. Jones

"INTRODUCTION Ethyl mercaptan (CH3,CH2SH), a combustible organic liquid of the thioalcohol type, is employed at an odorant in many types of fuel gases and dangerous atmospheres, which in themselves are devoid of characteristic odors, to give warring against leakage of such gases or atmospheres into places where they might constitute health or explosion hazards.Ethyl mercaptan has a penetrating disagreeable odor resembling that of onions, garlic, hydrogen sulfide, or rotting cabbage, that exceedingly low concentrations of it can be detected. The of odorants as a beans of detecting leakage of gases and atmospheres has been investigated extensively by chemists and engineers of the Bureau of Mines, and numerous reports as to its value have been published."

Jun 1, 1942

By D. R. Mathews

The Bureau of Mines investigated the effects of tungsten and chromium, separately and combined, on improving the mechanical properties and oxidation resistance of vanadium. Binary and ternary vanadium-base alloys were prepared and tested for oxidation resistance and tensile strength. Softening occurred with less than 1 weight-percent of either tungsten or chromium, followed by strengthening with higher alloying contents. Vanadium alloys containing up to 9.8 weight-percent chromium or 14.1 weight-percent tungsten were more resistant to oxidation in air at 600° C than unalloyed vanadium. For the alloys with 12.20 weight-percent chromium or 14.56 weight-percent: tungsten, the maximum concentrations used, the lower yield strengths were about twice that of 38,600 psi for the unalloyed vanadium. Recrystallization temperatures for these alloys were 100 and 150° C higher, respectively. Alloys containing both chromium and tungsten had properties similar to those of the vanadium-tungsten alloys.

Jan 1, 1967

By Raja V. Ramani

The potential usefulness of reclaimed surface-mined land has received much attention recently. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U.S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, the Chinook Mine-West Field, located in western Indiana, has been studied. The Chinook Mine is presently operated by AMAX Coal Company and has been in continuous operation since 1928 under various ownership. The status of current reclamation and land use planning was reviewed. In addition, site planning principles were applied to the active mine area. This application included formation of a data base and development of postmining land use plan alternatives. Key factors affecting site potential realization for midwestern area mines have been identified along with suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By Richard A. Winters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 334-acre Mountain Lakes Wilderness Study Area (OR-011-001) in order to evaluate its identified mineral resources. The study area is located in Klamath County about 15 miles northwest of Klamath Falls, Oregon, and is adjacent to the Mountain Lakes Wilderness. The area is underlain by Pliocene-age basaltic andesite. No mining districts are in the study area nor were any claims recorded or found. There are no oil and gas lease applications. There are no identified mineral resources in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Mountain Lakes WSA (Wilderness Study Area), at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1988

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.5 and 3 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year product Lon period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 Indexes. Initial capital investment is $33.8 million for the 1.5-MM-tpy mine and $61 million for the 3-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $52.5 and $94.2 million, respectively. These figures translate into total capital investments of $34.87 and $31.31 per ton of annual production. Assuming a desired 15-percent discounted cash flow rate of return, with Federal income taxes at 50 percent, the required selling prices would be $12.06 and $10.94 per ton for the 1.5- and 3-MM-tpy mines.

Jan 1, 1976

By Michael S. Miller

The Carson-Iceberg RARE II study area, consisting o; 209,990 acres (134,983 ha), is on the crest of the Sierra Nevada in California, about 35 mi (56 km) south of Lake Tahoe. The area is divided into four parts: C4-986; C5-986; and B5-986, north and south portions. No mineral production has been recorded for the area. However, gold, silver, and tungsten resources and potential for additional resources have been estimated for the area and just north of area C4-986.

Jan 1, 1981

By T. T. Read

"Education is the one thing which is unanimously regarded as valuable. The growing complexity of modern life, with its intricate organization, the manifold kinds of mechanical equipment that are used, and the constantly growing, necessity for the speedy and accurate interchange of information and ideas, make education an asset that constantly increases in value. The number of things that may profitably be known has grown so large that the field of education has been divided, and attention is often directed to only those things that are most immediately valuable. Modern educational facilities are often directed to what may be called corrective, work; the, providing of people with information that they teed in the conduct of their daily lives, but which for various reasons they have not previously had facilities for acquiring. The value of special education in the industrial world has been so thoroughly demonstrated that far-seeing managers of mining enterprises are always interested in the educational facilities existing in the community where their work is carried on.The educational facilities of a modern community may be classified in several ways. They may be divided into;1. Facilities for general education, for the purpose of increasing the whole field of knowledge of the student.2. Facilities for special education, which are intended to remedy a specific defect, or to give proficiency in some special field. This may be divided as follows;a. Training for work, intended to fit an employee to adequately perform the task assigned to him, this ranges from brief instruction by a foreman or fellow-worker up to definite training courses in which the employee dose nothing but study for a period of several weeks or months, being paid during this period a wage that may range from a nominal amount up to practically full time salary. The student's educational preparation may already be fairly advanced. Some of the manufacturers of electric machinery maintain, a school similar to that just described for graduates of engineering colleges. In other cases the only pre-requisite may be a common school education, as in the schools for operators, maintained by the telephone companies."

Apr 1, 1920

By A. Z. Dimitroff

An improvised rock-dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By John H. Soule

The Royal John mine was examined in November 1942 by a mining engineer of the Bureau of Mines, who proposed development of the Royal John and other properties in the area. Geologists of the U. S. Geological Survey studied the area in 1943 and 1944 and made definite recommendations. Also, in 1943 the Peru Miring Co. mapped the Royal John and did considerable diamond drilling. The Bureau of Mines started the Royal John portion of a project pertaining to the general district in April 1944. This project was completed in Juno 1945. The work, consisting of diamond drilling, was supervised by Robert O. Hill, mining engineer, and the results were published in Report of investigations 3904, Exploration of Grey Eagle, Grandview and Royal John Claims, Grant County, N. WIC. In 1947 and 1948 the Royal John was re-examined by a Bureau engineer, and additional development to increase the reserves of low-grade lead-zinc ore was proposed. This project was started in August 1948 and completed in Juno 1949.

Jan 1, 1950

Objective The Roof Monitoring Safety System (RMSS) introduced in late 1997 has been modified to improve durability and simplify the measurement of roof or rib movement. Greater knowledge about the stability of roof and rib rock is expected to result in safer conditions for the mine worker. Developing safety tools and methods is part of NIOSH’s mission to prevent work-related injuries and deaths. A mining operation with a proactive approach to control ground conditions is in a better position to make essential decisions related to mine development and take remedial actions in the event of roof or rib falls. Background Falls of roof and rib rock are responsible for a high number of mining injuries and fatalities. Visual inspections and the sound of breaking or cracking rock are often relied upon to indicate unstable roof conditions. In some mines, roof bolt holes are checked for separations or gaps with a scratch tool; this provides further information about the stability of the roof. Monitors such as the RMSS can confirm roof movement that was surmised only by eye or ear, or potentially detect movement that was missed by these means. An added safety feature of the RMSS is the capability of locating the measurement station at a distance from where the monitor is placed in the roof. Stone and other industrial minerals are the basic raw materials used in construction. Continuing economic growth and highway building in particular have resulted in record demand for stone. This high demand, coupled with increasing constraints on surface mining, have caused many new .stone mines to be developed underground. These new mines in many cases will be employing new and inexperienced miners who may not have the ability to recognize unstable ground conditions using just sight and sound. From the initial introduction of the RMSS, it was anticipated that improvements and modifications would occur. We correctly assumed that, once miners and operators were exposed to the monitor. suggestions would evolve. In one case, the RMSS was used to determine if an impact hammer used on a mechanical scaler was causing or increasing instability of roof rock. The test showed little or no movement resulted from this method of scaling under the particular conditions at this mine. In another instance, an operator needed to monitor the stability of a haulageway in a benched area that had very high ceilings. The RMSS requires a 2-in-diam hole for installation; however, only roof bolt holes of a smaller diameter were available, and it was impossible to drill new holes at that height. The operator attached a 2-in collar at the roof line and was able to install the RMSS. These examples illustrate the potential for further enhancements of this tool. NIOSH continues to seek additional candidate sites for use of the RMSS. As usage increases, we anticipate further refinements and additional applications. How It Works The new RMSS, cable, and read-out box are shown in figure l. The read-out box has a green light that stays lit until battery replacement is needed. The red light is set to conic on to indicate movement. The red light can he adjusted for increments of movement as low as .010 inches. The RMSS red light should not be considered as a primary or only means of determining the stability of roof or rib. It is intended to serve as a supplement to existing methods or procedures for determining stability. An overview of the RMSS components is shown in figure 2. Movement of rock layers within the mine roof is measured relative to a fixed-point calibration at the monitor housing. The housing contains a potentiometer, roller switch, plastic rack, and spur gear. Movements are detected by the transfer of electromotive forces

Jun 1, 2000

By Wing G. Agnew

The drilling and bit-sharpening practice in the southwest Wisconsin zinc district generally conforms to the procedure described herein, except at very small properties, where drill steel is sharpened by hand. Though hot milling of rock-drill bits is practiced in South Africa on some of the large-scale operations, it is seldom seen at American minus in any form. Because of the simplicity and low cost of the equipment, it was thought that a brief description might prove interesting to same of the operators in ether districts who do not have enough steel to sharpen to warrant equipping an elaborate sharpening shop.

Jan 1, 1936

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By B. J. Scheiner

Extraction of silver from silver mill tailings by an electrolytic oxidation procedure was investigated by the Bureau of Mines. Various parameters affecting silver extraction, such as electrolysis time, particle size, and dissolution of the silver as the tetrachloro or cyanide complex, were studied at 30° C with an electrolyte concentration of 20 weight-percent sodium chloride. Resulting silver extractions ranged from 77 to 90 percent, depending on the tailings being treated. Concomitant extraction of mercury ranged between 90 and 95 percent. Power consumption was 52 to 90 kilowatt-hours per ton for the tailings investigated. Comparative experiments using direct cyanidation resulted in extraction of 46 to 82 percent of the silver and 20 percent of the mercury. Cyanide consumption ranged from 3.3 to 9.4 pounds per ton of tailings, depending on the tailings being treated. Silver and mercury were recovered from leach solutions by precipitation on iron powder, followed by conventional distillation and fire refining steps.

Jan 1, 1972

By H. R. Babitzke

The purpose of this Bureau of Mine- investigation was to develop columbium and tantalum alloys suitable or u at elevated temperatures. Columbium and tantalum were combined with tungsten, hafnium, zirconium, molybdenum, vanadium, and titanium, and the resulting alloys were evaluated with respect to workability, hardness, electrical resistivity, strength at elevated temperatures, oxidation resistance, and weldability. Cb-33Hf-10W-10Ti, Cb-20111-5Mo, and Cb-30Hf-5Mo exhibited superior high temperature properties. Cb-33Hf-10W-10Ti had tensile strength values of 44,300 psi at 1,200° C and 16,500 psi at 1,400° C, Cb-20Hf-5Mo had values of 35,700 and 20,700 psi, respectively. The corresponding values for Cb-30Hf-5Mo were 38,900 and 17,800 psi. These alloys are fabricable by conventional methods with excellent strength at temperatures up to and including 1,400° C. An oxidation rate of 7 to 21 mg/cm2/hr was observed up to 1,000° C.

Jan 1, 1967

By J. W. Paul

This paper deals with the second phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the results public as rapidly as possible. Part 1 dealt with the resistance of unobstructed entries and was issued as Serial 2621 of the Bureau of Mines, in July 1924. Description of tests. After the resistance of an unobstructed entry to flow of air had been determined by tests in the Experiment mine, mine cars were; run into the test section in various arrangements and the increase in resistance was determined. The cars used were of the wooden type with loose end gate, and would hold about one ton of coal, level full. They were 7 feet long. 4 feet 2 inches wide above the wheels, 3 feet high, and had a cross-sectional area of approximately 10 square feet. The average area of the entry was about 57 square feet, the ratio of unobstructed to total area being about 17.6 per cent. The track gage was 42 inches and the wheel-base 20 inches.

Jan 1, 1924

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and Other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By T. Christos

The explosive oils, nitroglycerin (NG) and ethylene glycol dinitrate (EGDN), were extracted from dynamites by a halocarbon solvent and were then determined by high-pressure liquid chromatography. Separation was achieved by liquid-liquid chromatography on a column packed with Durapak-Carbowax 400/Corasil II and the eluted NG and EGDN were detected with a double-beam ultraviolet detector.

Jan 1, 1973

By Walter K. Utt

The vibration levels of the heavy machines used in surface mining are much greater than for vehicles used on highways. In order to assure the proper functioning of electronic equipment placed on the surface mining vehicles, the U.S. Bureau of Mines has conducted a program of field measurements to define their vibration environment. The information in this report is for a class of vehicle that has a blade for scraping and wheels with rubber tires. The statistical information derived from these measurements can be used as a basis for laboratory testing to qualify equipment for a surface mining vehicle of this class. The envelope that would encompass 99 pct of the vibrations encountered in normal operations is presented for each location on the vehicle. The five locations for which data were recorded are the floor of the cab, the engine, the frame, the drive train (gear, differential, and torque converter), and the axle. Tabulated data are provided for those who wish to use a different probability level. The appropriate test profile for the laboratory testing can be determined from the information presented in this report.

Jan 1, 1993

By William E. Wallace, S. J. Page, B. L. Razzaboni, C. A. Hill, Pamela Mike, P. Bolsaitis, M. J. Keane, Val Vallyathan

"Respirable quartz cytotoxicity, as measured by erythrocyte hemolysis and pulmonary macrophage release of lactate dehydrogenase in vitro, is neutralized by boiling in water in glass test tubes for 10 to 40 minutes. The cytotoxicity is reduced to near zero by boiling l to IO mg quartz per milliliter water. For greater concentrations of quartz in water the hemolytic potential after 40 minutes of boiling approaches that of native quartz. Replacing the medium with fresh water midway through boiling results in full detoxification through 20 mg quartz per milliliter water. Pre-boiling the medium with silica reduces the detoxification effect. Detoxification persists after mild drying at l 10°C for 8 hours, and persists after three days of resuspension in water at room temperature.INTRODCJCTIONResearch underway to determine interactions of quartz and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages were suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosmal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121°C with no liquid water but with steam present. 1.2 However detoxification under boiling conditions has been reported in other research. 3 It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity simplicity and cost.RESCULTS AND DISCCISSIONRespirable quartz dust used in this study was taken from a stock of crystalline silica, Min-U-Sil; obtained from Pennsylvania Sand Glass Corporation, fractionated in air with a particle classifier. The small size fraction retained for use was 80% less than S micrometer particle diameter, with an area equivalent median diameter of 1.24 micrometers as estimated by automated image analysis. The silica was at least 98.S mass percent silica as determined by X-ray energy spectrometric analysis; and the crystalline form was alpha-quartz as determined by X-ray diffraction. It's specific surface area was 3.97 square meters per gram as determined by nitrogen adsorption isotherm methods. I"

Jan 1, 1990