Search Documents

By J. F. Brand, J. C. van Dyk, F. B. Waanders

"Syngas from Africary’s Theunissen underground coal gasification (UCG) project will be used for power production and synthesis of liquid fuels and commodity chemicals. However, some of the coal components, especially condensable water, oils, tars, inorganic trace elements, and a small fraction of fly ash and particulate matter, make their way to the surface via the production well and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as Rectisol®, but with the downside of low energy efficiency and waste water generation. In this paper, novel technologies for removing contaminants and species separation from the hot (T > 300°C) raw syngas are compared. Comparisons are made between supersonic gas separation (SGS), Ranque–Hilsch vortex tube (RHVT), vortex gradient separation (VGS), and inertia vacuum filtering (IVF), and a vortex-based gas separation concept is proposed for UCG applications. IntroductionImpurities in gasification feedstock (coal, biomass, waste, etc.), especially sulphur, nitrogen, chlorine, and inorganic mineral matter, often end up in the syngas and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as RectisolR, SelexolR or aMDEAR; but with the downside of low energy efficiency and waste water generation.Hot (T > 300°C) gas clean-up technologies are attractive because they avoid cooling and reheating of the syngas stream. Some available warm gas cleaning technologies include traditional particulate removal devices such as cyclones, candle filters, membranes, and molecular sieves. The warm gas desulphurization process technology developed by RTI LLC (2018) requires hot syngas to remove sulphur and has become commercially ready. Many other hot gas cleanup systems are still under development, given the technical difficulties caused by extreme environmental and operating conditions."

Jan 1, 2018

By A. E. Voigt

Iron ore samples representing the input and output of several jigging experiments were analysed to determine the effect of particle size, shape, and density on jigging performance. Traditionally, the manual measurement of the size and shape of individual particles is very tedious and prone to inaccuracies and inconsistencies. Using a novel multi-view imaging technique the 3-dimensional representations of each particle in the sample was determined. From this representation several size and shape measurements were extracted, and these were correlated with the individual particle density measurements. A rigorous investigation into the confidence associated with density and the size and shape features as a function of sample size was conducted, thus allowing the significance of correlations in the data to be determined. The jig?s performance was seen to be clearly sensitive to density and markedly so to particle size, while the results for shape indicated the need for continued work in the definition of particle shape.

Jan 1, 2012

Foamed cement packs offer a viable alternative to conventional timber or other forms of packs for permanent underground support. These packs comprise steel mesh and hoop containment with an outer bag for the grout; woven, laminated polypropylene fabric being ideal for the purpose. The grout is supplied in 25kg bags and fed into a purpose ? designed foam placer machine which delivers the foamed grout directly to the packs from 60 metre long delivery hose. Foamed cement grout as a fill material offers attractive properties for support packs, in summary these are: Variable Grout Strength Grout strength is controlled by the grout density being delivered from the placer machine. This can be changed by the machine settings. Strength Development Fast rate of strength development is possible so that support is available quickly. Pack yield The foamed grouts are compressible so that yielding of the grout pack can be achieved without loss of support. Rate of Filling Three sizes of placer machine are available, these use one, two, or three 25kg bags per minute of grout, pack filling time is therefore a matter of minutes, a typical 0.75m diameter pack x 1.2m high taking some 17 minutes to fill. Tests in a 1000 tonne press have confirmed that the above characteristics can be achieved with foamed cement packs at acceptable cost. This will be illustrated in the paper with experience to date.

Jan 1, 2008

By K. Woodward, Y. Potvin, B. McFadyen, M. Grenon

Open stoping has become a popular mining method in hard rock mines, not only due to the safety of the method as a non-entry approach, but also because of the high extraction rate and low costs. At mine sites, stope performance is evaluated by calculating stope overbreak using the stability chart. However, limitations of the stability chart regarding the precision of the predictions, nonconsideration of factors such as the influence of blasting, and the exclusion of underbreak have led to non-optimal designs. The capabilities of today's computers have increased the amount of data being collected and the power of models being built. This article presents a step towards a new stope design approach where stope overbreak and underbreak are measured and georeferenced using octrees at an approximately cubic metre resolution and predicted using multivariate statistical models (partial least square, linear discriminant analysis, and random forest). Results show that overbreak and underbreak location along the design surface and their magnitude are predicted with good precision using a random forest model. These predictions are used to build the expected geometry of the open stope. The resolution of the data and the use of multivariate analysis has enabled the prediction of variation in stope performance along the design surface, going well beyond the simple qualitative per stope face prediction provided by a traditional stability chart approach.

Jun 5, 2023

By M. Royle, A. Bloem, R. Uken

Rock mass damage induced by mining increases the fracture frequency and joint aperture width in the pit walls and rock mass behind open pit mine slopes. The depth and intensity of this mechanical damage relative to the pre-mining state is not well understood and yet is a major factor in the development of slope stability models and operational guidelines. The induced damage can be partitioned into domains or zones. The blast damage zone is essentially a ‘free flow’ rock mass volume, which transitions quite rapidly into the excavation damage zone, which extends beyond that. In both zones, transient high in situ water pressures are often linked to unstable slope conditions. Whereas rock damage can enhance passive depressurisation in the rock mass, high infiltration rates on the other hand, as one could expect during rainstorm events, will decrease slope stability within the dilated pit rock mass, especially in the blast damage zone-excavation damage zone, by increasing pore pressures for short periods of time. Ice jacking and freshet are additional factors to consider in (sub) arctic environments and can be exacerbated by unfavorable rock fabric orientation. On a local scale, brittle deformation damage zones, in the form of faults, can contribute to slope instability, or enhanced stability because of slope depressurisation, depending on their location and orientation relative to the pit shape and the water sources. In this study, the shapes of the damage zones and their anticipated impact on infiltration and/or passive depressurisation are considered for different pit morphologies, rock mass conditions, in situ stress, and hydrogeological settings. Some unusual hydrological situations, like mining towards rivers and lakes and the potential effects on pore pressures, are also considered. This investigation has resulted in the development of a method to adjust initial hydraulic conductivity values used to estimate transient pore pressure conditions found in rock masses exposed in different pit morphologies and stress regimes as well as discontinuities’ orientation relative to open faces within the open pit mine. The changes in K values and pore pressures can then be used to determine hydrogeological influence more accurately on future pit slope stability.

Sep 1, 2025

By A. McQuillan, N. Bar

Geotechnical models developed during the planning stages of open pit mines are three-dimensional so as to capture the spatial variation in lithological, structural, hydrogeological, and geomechanical conditions. Geological models that describe the lithological and structural (faulting and folding) characteristics of a deposit are always 3D. Likewise, boreholes and piezometers used to develop geomechanical properties and groundwater models are drilled at spatial offsets across the deposit to understand the lateral and vertical characteristics. Yet when geotechnical analysis is completed, often the three-dimensional geological, hydrogeological, and structural models as well as geometrically complex 3D mine designs for optimizing economic mineral recovery and overburden removal are simplified to two-dimensional sections. In this paper we demonstrate that this simplification can lead to the wrong failure mechanism being identified, analysed, and/or a conservative factor of safety being calculated and hence an over-estimation of slope stability. Through case studies we show how three-dimensional analysis methods are more suited to rock slopes, particularly those with anisotropic material strength, when singularities such as geological faults are present, and nonlinear slope geometry. When the same slopes are analysed in two dimensions, the failure mechanism calculated is often fundamentally incorrect. The case studies further reveal that the factor of safety calculated in three dimensions is not always higher than the two-dimensional factor of safety.

Feb 6, 2023

By S. W. Jacobsz, Y. Narainsamy

Several high-impact tailings dam failures around the world in recent years have placed a renewed focus on the stability of tailings dams and pointed to potential shortcomings in traditional drained design and safety evaluation procedures. A need to consider undrained shear strength in the design of tailings facilities has become apparent. However, there are specific requirements that need to be met before undrained shearing occurs. In South Africa, the last major failure was likely the Merriespruit disaster in 1994, which leads to the question of whether the conditions required for undrained shearing are readily applicable to South African tailings dams. This paper describes research at the University of Pretoria that has recently commenced to further investigate the conditions required for undrained failure to occur. The research includes laboratory and field testing to replicate these conditions in the laboratory and relate them to those found in an active tailings dam.

Jun 2, 2022

By L. Kühnel, H. Lieberwirth

Confined bed comminution in High Pressure Grinding Rollers (HPGR) and Vertical Roller Mills (VRM) is gaining substantial attention in many applications. Previously used mainly for milling coal or construction materials, HPGR and VRM have started to complement or even replace tumbling mills in ore beneficiation. Materials like coal or clinker are relatively homogenous, however, in comparison to metal ores and wall rocks. This characteristic poses a new challenge to the confined bed comminution but also an opportunity. Fuerstenau and Abouzeid have investigated the selectivity in comminution of a mixture of particles of different strength in a particle bed. The median particle size and particle size distribution (PSD) of the two constituents used were kept constant. Only the proportion of the two constituents was modified. The competence of a material is, however, also a function of particle size. Smaller particles tend to be more competent than larger ones of the same material. If selective comminution is applied on ores, this size influence has to be understood. The paper presents research results on this topic based on experimental investigations with model materials as well as with natural particles, which were stressed in a piston-die press. It appeared that the comminution result depends substantially on the material characteristics and the composition of the mixture. Conclusions will be drawn for the application in future applications of selective comminution in mineral processing. Keywords: Confined bed comminution, HPGR, VRM, piston die press, particle size

Jan 1, 2020

By J. J. Botha

As a Demand Side Management (DSM) Project, money was granted for the procurement and installation of a 3-Chamber Pipe Feeder System (3-CPFS) at AngloGold Ashanti?s Moab Khotsong Mine in the Vaal River Area, Orkney. The first submission was done to ESKOM in December 2002 and the contract was signed in September 2006 at a cost of R 57-million with an envisaged reduction in power of 7 Megawatt per month based on a 90% utilization factor. The project was finally commissioned in December 2008. The technology is not new, but the intent of the paper is to share with others the experience gained by using the technology in a deep-level mine in order to reduce overall power consumption.

Jan 1, 2009

By Y. Chen, D. He, J. H. Potgieter

The demand for rare earth elements (REE) is increasing rapidly owing to the emergence of new cleanenergy and defense-related technologies. China’s dominates the world production of REE. In this paper, we review the ore characteristics of four typical REE deposits in China and discuss the conventional beneficiation techniques, including gravity and magnetic separation, flotation, and hydrometallurgical processing of these ores. Some of the latest laboratory findings and industrial applications, as well as the development of novel reagents for REE processing in China are presented. The REE beneficiation technologies developed and employed in China could constitute a good case study for many other emerging projects being explored around the world.

Mar 2, 2022

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

By X. Yang, G. D. Zhai

The prop is the most important part to ensure the proper functioning of hydraulic support. When the hydraulic support is impacted by the roof, the prop is prone to extrusion deformation, expansion, and even bursting. In order to study the stress on a doubly-telescopic hydraulic support prop under impact load, an impact simulation was carried out based on the drop weight method. First, the impact model of the hydraulic system of the prop was established in AMESim software and the dynamic response curves of the bottom and middle cylinder of the prop obtained. Then, according to the conservation of energy, the pressure formulaes in the hydraulic cylinder of the prop under impact load were derived and verified by the AMESim simulation results, and the maximum pressure on the inner surface of the hydraulic cylinder of the prop obtained. Lastly, the transient dynamic simulation of a hydraulic support prop was carried out in ANSYS Workbench software, and cloud diagrams of stress and deformation of the prop obtained using Workbench simulation. The AMESim simulation process describes the change in fluid pressure in the prop, and the pressure formulae can be used to estimate the internal pressure of the prop under impact load. The finite element analysis results show that the stress of the middle hydraulic cylinder is much greater than that on the bottom hydraulic cylinder under impact load, which can provide a reference for prop design.

Jul 2, 2022

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

By R. B. Ngenda

The ?Kolwezi Zinc Plant?, in French ?Usines à Zinc de Kolwezi? (UZK), has produced about 910 000 dry metric tons of residues during the hydrometallurgical treatment of calcines from sulphide zinc concentrates. The zinc hydro plant residues contain on average 19.47% Zn, 2.7% Cu, 2.1% Pb, 26.6% Fe, 0.12% Cd, 0.39% As, 157ppm Ag, 447.8 ppm Ga, 475.4 ppm Ge, etc. This material was dumped in five ponds in the vicinity of the plant. The high Fe content in the ore concentrates induced important conversion of some of zinc and copper into ferrites during the roasting process. Those ferrites are very stable compounds, which are difficult to leach with dilute sulphuric acid solution. Therefore, they mainly report to the leaching residues. Hot leaching has been successfully applied to the treatment of zinc hydro plant residues. The method, however, presents the disadvantage of simultaneously dissolving iron(Fe). It is then necessary to remove an important iron quantity from solution prior to zinc and other metals recovery.

Jan 1, 2009

By S. Kauchali

"Underground coal gasification (UCG) is recognized as an efficient mining technique capable of chemically converting the coal from deep coal seams into synthesis gas. Depending on the main constituents of the synthesis gas, chemicals, electricity, or heat can be produced at the surface. This paper provides a high-level graphical method to assist practitioners in developing preliminary gasification processes and experimental programmes prior to detailed designs or field trials. The graphical method identifies theoretical limits of operation for sensible gasification within a thermally balanced region, based primarily on the basic coal chemistry. The analyses of the theoretical outputs are compared to actual field trials from sites in the USA and Australia, with very favourable results. A South African coal is studied to determine the possible synthesis gas outputs achievable using various UCG techniques: controlled retractable injection point (CRIP) and linked vertical wells (LVW). For CRIP techniques, an important result suggests that pyrolysis, and subsequent char production, are important intermediate phenomena allowing for increased thermal efficiencies of UCG. The conclusion is that South African coals need to be studied for pyrolysis-char behaviour as part of any future UCG programme. The results also suggest that UCG with CRIP would be a preferred technology choice for Bosjesspruit coal where pyrolysis dynamics are important. Lastly, the use of CO2 as oxidant in the gasification process is shown to produce syngas with significant higher heating value. Introduction and literature surveyCoal is a commonly utilized fossil fuel, providing over 40% of global electricity demand and about 90% of South Africa’s primary energy needs. However, less than 20% of the known world resources are suitable for possible extraction using conventional surface and underground mining techniques (Andrianopolous,, Korre, and Durucan, 2015). Underground coal gasification (UCG) has the potential to recover the energy stored in coal in an environmentally responsible manner by exploiting seams that are deemed unmineable by traditional methods. The UCG process, if successfully developed, can increase coal reserves substantially. For example, in the Limpopo region of South Africa alone, the estimated potential for UCG gas, based on existing geological records, is over 400 trillion cubic feet (TCF) natural gas equivalent – this is about a hundred times more gas than the existing 4-TCF Pande-Temane natural gas field reserve in Mozambique (de Pontes, Mocumbi, and Sangweni, 2014)."

Oct 1, 2018

By A. Drumond, J. F. C. L. Costa, M. G. Lemos, A. L. Rodrigues, F. G. Niquini

The past decade has seen a renewed possibility of using machine learning algorithms to solve a large collection of problems in several fields. Data acquisition for mining operations has increased with the growth in sensor-based technologies, and therefore the amount of information available for mining applications has dramatically increased. Ore sorting equipment is available for separating ore from waste based on differences in physical properties detected by a real-time analyser. The separation efficiency depends on the contrast in these properties. In this study we investigate the application of machine learning models trained using data from the output of a dual-energy X-ray ore sorting apparatus at a gold mine. The particles were first hand-sorted into ore and gangue classes based on their mineralogical composition. Classification models were then used to help decide the balance between the number of true and false positives for ore in the concentrate, with a view to economic parameters, using their receiver operator characteristic (ROC) curves. The results showed AUC (area under the ROC curve) scores of up to 0.85 for the classification models and a maximum reward condition Fpr/Tpr around 0.5/0.9 for a simplified economic model.

Aug 8, 2024

By S. J. van Wyk, A. S. H. Haagner, A. Abraha

Opencast coal mining is responsible for the greatest area of land disturbance across all of the commodity types in South Africa. Many thousands of hectares have been rehabilitated to date and, although rehabilitation performance is not always measured or reported, a significant database, spanning 24 years, has now been analysed to identify the main shortcomings holding back rehabilitation sustainability across the industry. Data from 48 different collieries with rehabilitation performance scores measured from 2000-2024 were analysed. A standardised assessment framework was implemented at all 48 collieries, focusing on aspects of land capability, soil fertility, landscape form and drainage, vegetation species composition and basal cover, implementation of maintenance programmes, and prevalence of invasive alien plants. The findings show that, although invasive species management, plant species composition, and plant basal cover are often adequate, the implementation of aftercare and maintenance programmes (influencing soil fertility) and deficiencies in overall landform design and drainage systems are most significant in preventing overall rehabilitation progression and self-sustainability. Integrating these during design and rehabilitation execution, followed by intensive maintenance (especially in the first five years post-topsoiling and seeding) will be key for the overall industry performance to improve to acceptable levels. The database is biased towards collieries that actually do undertake rehabilitation and that do measure it, hence the actual industry performance is likely worse than what is presented. Due to the substantial hectarages involved and the main post-mining land uses being grazing and crop production, the industry cannot afford to keep perpetuating deficiencies in achieving the foundational aspects of rehabilitation that would pave the way for sustained economic future use.

Apr 25, 2025

By R. Simon, P. Pagé, L. Li, P. Yang

The Mathews-Potvin stability method is widely used in the Canadian mining industry as a starting point to determine the maximum dimensions of mine stopes. However, it cannot be applied to inclined (more frequently encountered) mine stopes without conducting numerical modelling to obtain the stress factor A, defined as a function of the ratio of unconfined compressive strength of intact rock to the induced principal stress on the exposed stope walls. The need to conduct numerical modelling significantly limits the application of the Mathews-Potvin method. In addition, given its empirical nature and main application for preliminary design, it is deemed undesirable to conduct numerical modelling, especially elaborate modelling. Alternatively, theoretical methods can provide a much simpler and quicker way to estimate stresses around stopes and the corresponding stress factors. Over the years, a large number of studies have been conducted to estimate stresses around openings excavated with various crosssections. However, theoretical or graphical solutions remain unavailable for mine stopes that typically consist of horizontal floor and roof, and two parallel inclined walls (hangingwall and footwall). To remedy this situation, a series of numerical simulations is first performed for openings with vertical and inclined walls, including typical stopes commonly encountered in underground mines. A group of empirical solutions is then formulated to estimate the induced principal stresses at the roof centre and mid-height of the stope walls. The validity and predictability of the proposed solution have been verified using additional numerical simulations. The proposed solution can thus be used to calculate stresses and the resultant stress factors A around typical mine stopes with any inclination angle and height to width ratio, under any in-situ stress state, without conducting numerical modelling.

Aug 1, 2021

By U. Atici, R. Comakli

"Understanding rock properties is of vital importance in mining and civil engineering. Rock properties are generally determined through laboratory tests, which require a large number of uniformly shaped samples and technicians who use indirect methods to determine rock properties. The texture coefficient (TC), which represents various textural parameters including the size, shape, orientation, and relative proportions of grains and the matrix, is an efficient means for indirectly evaluating the mechanical behaviour of rocks. In this study, 12 different rocks (ten granites, one diorite, and one gabbro) were collected and their engineering properties. including specific gravity, porosity, P- and S-wave velocities, Schmidt rebound hardness, uniaxial compressive strength, and elasticity modulus, were investigated. Relationships between TC and these measured properties were assessed. Statistically significant (at the 95% confidence level) correlations were found between the TC and compressive strength, elasticity modulus, sound velocity (both compression and shear waves for dry and saturated samples), but no significant correlation was found with Schmidt rebound hardness. The results suggest that it is possible to use the relationships between TC and the mechanical properties of rocks in rock classification. IntroductionIn every aspect of rock engineering, knowing rock properties is essential for determining and predicting the behaviour of rocks and rock masses. Mechanical properties of rocks are important parameters in mining, geology, and engineering, and they are affected by textural characteristics such as grain size, grain shape, cement type, degree of cementation, mineral content, and the ratio of the grain area to the matrix area. The effects of textural properties on the physical and mechanical properties of rocks have been investigated for a long time, and previous studies revealed close relationships between single parameters related to rock texture and mechanical properties of rocks (Akesson et al. 2001; Gunsallus and Kulhawy 1984; Merriam, Rieke, and Kim, 1970: Onodera and Kumara 1980; Prikryl 2006; Ulusay, Tureli, and Bider, 1994; Tugrul and Zarif 1998). Rock properties are usually determined using mechanical tests, which require uniformly shaped and relatively large samples. However, it is not always possible to obtain such samples. Furthermore, rocks with similar textural and structural properties may exhibit different mechanical behaviour. Howarth and Rowlands (1987) developed a texture coefficient (TC) that expresses all the main textural parameters of a rock in a single dimensionless quantity based primarily on statistical assessment. The TC makes it possible to understand the effects of a rock’s textural properties on its mechanical properties using thin sections instead of large, uniform samples. Ersoy and Waller (1995) investigated the relationship between strength and TC for limestone, sandstone, and siltstone; they also examined the effect of rock properties and TC on drilling performance. Ozturk, Nasuf, and Bilgin (2004) explored the relationship between rock quality and TC by evaluating the uniaxial compressive strength (UCS) values of limestone, basaltic andesite, and tuff. Gupta and Sharma (2012) evaluated TCs as well as the petrophysical and mechanical properties of quartzite from the lower and higher Himalayas and found a strong relationship between TC and UCS. Similarly, Ozcelik, Bayram, and Yasitli (2013) investigated the relationship between TC and various parameters in marble by applying the statistical analyses developed by Ozturk, Nasuf, and Kahraman (2014)."

Jan 1, 2019

By T. Moodleya, I. Govender

Despite the widespread use of DEM to simulate particle processes, comparatively little work has been done to evaluate its accuracy. One of the reasons is a lack of available measurement techniques that can capture dynamic information at the momentum transfer timescale which is lower than 10-6 s - typical of the kinetics occurring within the drum. This work makes use of Positron Emission Particle Tracking (PEPT), an in-situ method capable of measuring 3D kinematic data at 1000 frames per second. PEPT measurements are performed using 3 mm and 5 mm mono-size glass beads in a 300 mm diameter rotating drum at critical speeds that are relevant to industry. We undertake systematic ‘tuning’ of DEM with a view to optimising the agreement between experiment and simulation. To ensure an equitable comparison scale, both the DEM and PEPT data are coarse grained within representative volume elements. This work seeks to validate DEM predictions against experimentally derived PEPT kinematic measurements. Keywords: PEPT, nuclear imaging, DEM, Tumbling Mills

Jan 1, 2020