Search Documents

By O. Ozcan, J. D. Miller, Z. S. Nickolov

The production of soda ash from trona (sodium sesquicarbonate, Na2CO3•NaHCO3•2H2O) resources has completely displaced the production of synthetic soda ash in the USA. Further, the utilization of other trona resources is under consideration in China, Turkey, etc. Recent research has been concerned with the development of flotation technology for the trona industry. In this regard studies on the flotation behavior of sodium carbonate salts: trona, sodium carbonate monohydrate and decahydrate, as well as the flotation behavior of sodium bicarbonate, are reported for both cationic (dodecyl ammonium hydrochloride) and anionic (sodium dodecyl sulfate) collectors. It has been found that strong flotation of sodium bicarbonate (NaHCO3) can be achieved with 100% recovery, while the other sodium carbonate salts do not float well. These results have been explained by FTIR analysis of aqueous solutions of Na2CO3and NaHCO3in a range of concentrations from very dilute to saturated conditions. The changes in the shape of the O-H stretching band of water are correlated with the flotation behavior of Na2CO3salts and NaHCO3. In addition, the absorption band of the carbonate ion at ca. 1385 cm-1is used to monitor its interactions with water and/or other ions in solution. The infrared results demonstrate thatNa2CO3acts as a water structure maker, leading to an extensively hydrated surface that accounts for the poor flotation of most sodium carbonate salts. In contrast, NaHCO3does not have this characteristic and consequently complete flotation is possible with both cationic and anionic collectors. These results support the previous water structure analysis for soluble salt flotation of alkali halides and other oxyanion salts.

Jan 1, 2003

By D. Olsen

The paper discusses the legislative and practical approach adopted to problems of management of environment in relation to coal mining in a very sensitive area of the south coast of New South Wales. The environmental problems are complicated in this area due to multiple and very often conflicting land usages. The environmental approach in relation to water quality maintenance, noise control and air quality is discussed and methods adopted meet stringent requirements. Requirements of New South Wales Regulations on Environmental Impact Statements (EIS) are described.

Jan 1, 1988

By Cheryl L. Mardock, Michael D. Strickler

The Bureau of Mines is examining mineral deposits bearing strategic elements such as cobalt, for which the United States heavily relies on imports. The Turner-Albright volcanogenic sulfide deposit in southwestern Oregon is marginally economic based on its gold content and associated silver, copper, zinc, and cobalt values. Bureau research on the Turner-Albright deposit was performed (1) to evaluate domestic cobalt recovery as a byproduct of gold production from massive sulfide ores; (2) to develop an analogue of modern sea-floor polymetallic deposits to determine the economic potential of the deep-sea resources; and (3) to compile information on the geochemistry and genesis of the deposit that can aid in future onshore exploration. Cold was introduced as near micrometer-sized disseminations by exhalative hydrothermal fluids near sea-floor vent sites and by late influxes of mineralizing fluids into lower zones of brecciated sulfides and basaltic fragments. Cobalt is a substitutional element in pyrite that occurs in outlying halos around original vent sites. Mineralogic studies conducted with a scanning-electron microscope and an electron microprobe determined that none of the ore minerals are amenable to traditional beneficiation methods such as gravity and flotation. An experimental oxygen pressure-leaching procedure developed by the Bureau has proven successful in treating such complex ores.

Jan 1, 1990

By R. Mathur

Cu isotope fractionation in low temperature aqueous environments has been well documented. Here we apply Cu isotopes to two distinct, yet related mining problems. First, an exploration geological application where we measured copper isotope fractionation in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in 4 porphyry copper deposits located in South western USA. Cu isotope patterns exist in the lateral and vertical distribution within the mines coupled with distinct relationships with Cu grade. Second, a hydrometallurgical application where we measured the leach fluids, feed and residues from a quick leach text of Cañariaco ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the power and ability of using the Cu isotope technique to understand low temperature aqueous processed involving copper.

Jan 1, 2010

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.

Jan 1, 2003

By William Petruk

Lithium bearing lepidolites from three deposits in the province of Goias in Brazil were investigated to determine whether there is a correlation between the lithium content of the mineral and the colour of lepidolite and associated tourmaline. Such a correlation can be a useful guide to field geologists for outlining high grade ore zones. It was found that mauve-pink lepidolite associated with pink tourmaline, and brownish lepidolite associated with black tourmaline have high lithium contents, but the colour of lepidolite is not due to lithium. The pink colour of lepidolite and tourmaline is likely to Mn3+, and the brownish tint of lepidolite and black colour of tourmaline to Fe3+. Lepido lites appear to be lithium-rich when the lepidolite and associated tourmaline contain relatively high amounts of Mn3+ and/or-Fe3+.

Jan 1, 1985

By Vladimir Adamek

Due to the variability of subsidence characteristics across the U.S. coalfields, it was concluded that it would be practically impossible to develop a universal predictive model for mining-induced subsidence based on theoretical assumptions. Therefore, an effort was made to find a procedure to develop an empirical subsidence predictive model based on a sufficient Mount of field data from one mining area (in this case the Northern Appalachian Coal Region). It was also thought that this procedure, if successful, could be used as the template for developing predictive capabilities for other coalfields with different subsidence characteristics given a reasonable amount of field data. It has been found, in the Northern Appalachian Coal Region, that the variability of subsidence characteristics can be expressed by a polynomial equation developed through regression analysis of the variable subsidence coefficient and derived directly from the field data. In this study, field data were obtained from 11 Bureau longwall panel studies (16 half profiles) for static subsidence and 14 panels for dynamic subsidence. The effects of lithology, expressed in the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hythetically homogeneous overburden and existing ithological conditions. For each longwall panel, the characteristic of the variable subsidence coefficient was defined along individual static profiles. The definition of mean values with acceptable deviations is the substance of the predictive method. The same procedure was used to develop a predictive model for dynamic subsidence, since it war discovered that the rate of longwall face advance is not a necessary functional parameter. This paper presents the theory, development, and application of the static and dynamic subsidence prediction models.

Jan 1, 1986

By S. Painter

The effects of forced ventilation and thermal radiation in open drifts are included in three-dimensional thermal hydrology simulations of a potential waste repository at Yucca Mountain, Nevada. A semi-analytical model is used to calculate the amount of waste heat removed by ventilation air during each time step of the multiphase thermal-hydrology simulator. The model accounts for thermal radiation and changes in air temperature and humidity along the emplacement drifts. The fraction of heat removed by ventilation is time and position dependent.

Jan 1, 2004

By Z. T. Bieniawski

Ground support requirements for safe and economical design of room and pillar coal mining layouts are reviewed. The design methods for mine roofs and mine pillars are discussed and the role of the geotechnical aspects is considered. It is shown that current support design procedures in the United States do not utilize fully the latest research findings and the need for more effective technology transfer in coal mine ground control is emphasized. Promising new developments in ground support are identified and possible research areas are suggested.

Jan 1, 1982

By J. Pang

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and AC impedance spectroscopy techniques. Analysis of the impedance spectra using equivalent circuit models has made it possible to suggest layerwise growth of surface films. From the value of equivalent circuit parameters, properties of the surface layers are inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution and give rise to changes In contact angle and flotation response. In agreement with prior investigations, the present study shows that flotation recoveries alone cannot be used to determine the effect of collector on flotation of chalcopyrite. The rate of flotation is a more sensitive parameter to determine the role of collector on floatability of chalcopyrite.

Jan 1, 1989

By S. K. Das

A detailed strata-mechanics investigation and examination was carried out in the E2 Panel (ML-II/7) of the XVI Bottom coal seam, which is located in the Moonidih Colliery of B.C.C.L., Jharia coalfield, India. Above this panel, the XVI Top coal seam was previously worked out by a longwall panel. Based on intensive field study and on experiments in a number of longwall panels located within various Indian coal mines, the actual behavior of the coal roof strata was evaluated and new strata-mechanics concepts around the longwall panels were developed. These concepts resulted in new methodologies concerning the behavior of roof rocks, caving characteristics, etc. within longwall panels and in the area of strata mechanics. Based on these new strata-mechanics concepts, a very simple, but realistic, model was developed to determine the optimum capacity of the powered supports. This model considered the combined loads resulting from the detachment of strata and composite layer blocks from the face and, also, loads due to the deflection of strata and composite layers situated above the detached roof rockmass. This formula, along with the other related formulas by the author, prompted the determination of the optimum capacity requirement for the powered supports to be used in the XVI Bottom coal seam, located under the worked out area. This new concept in strata mechanics and capacity requirements of the powered supports in a longwall face may be an aid to Mining Engineers.

Jan 1, 1997

By Gemei Yang, Yihui Zhao

In caved goaf, the friction loss of fluid head is: [h = (R'+ R/Q/ )] Q (for one-dimensional transition flow). The R' and R, which are the functions of two dimensional spaces, are calculated through an empirical formula. Then, the bulking factor and permeability are determined. It is supposed that the airflow in porous media are similar to those in tiny tubes crossing each other. Therefore, the network calculation technique can be used to tackle the field transition flow problem. A lot of case studies showed that the emission of methane in mines mainly depends on the air velocity and has little relation to air pressure. Summing up our experience and experiments, we provide an empirical formula to calculate the gas emission rate per unit area. By means of mass conservation and network calculation, the methane content distribution in steady-state is worked out. Then the dynamic change in airflows and gas content can be analyzed by the characteristic-difference method.

Jan 1, 1987

By Ping Xia, Yaoxin Lu

With productivty increment. it becomes very important to monitor the underground production environment. This paper presents a multi-level computer monitoring and managing system, which was specially developed for the mine. In this system, TF-200, Industrial Standard Buses (STD) and 32 bytes Super micro-computer were integrated into one body as hardware; Data Base was designed by means of software engineering method in the software development; on maitenance of the system, the parameters are managed concentratedly and data are classified to process; therefore, the ystem gets to the advanced level in China. The system is composed of four sub-stations: Signal Transmission. Data Collection, Data Processing and Image Display Sub-system. Signal Transmission Sub-system(STSS) A frequency-division transmission method is used. Data Collect ion Sub-system (DCSS) Industrial Standard Buses (STD) is used. It can change data from STSS into suitable form for DCSS, Calculate average value every minute, decide alarm and transmit data to DPSS. Data Processing Sub-system (DPSS) The host is a S/120. With UNIX Operation System. the data from DCSS can be classified. stored, displayed. printed, by means of real-time and time-division processing. Additionally the functions of the historic data search and data analysis are provide. Image Display Sub-system (IDSS) The real-time and historic data was displayed for curves and diageams on screens. This system has been in operation.

Jan 1, 1991

By J. A. Nelen, R. B. Cook

Panned stream-sediment, geochemistry-based gold exploration in those parts of the southeastern Piedmont proximal to the Fall Line must take into account potential contamination from basal fluvial sediments of the Coastal Plain. Anomalies attributable to the incorporation of placer gold of Coastal Plain origin into modern Piedmont drainages have been identified in portions of Lee, Macon, and Tallapoosa Counties, AL, and Baldwin and Hancock Counties, GA. Identification and interpretation of such multicyclic anomalies must be based on knowledge of the local maximum Cretaceous transgression, paleotopography, modern and paleofluvial system dynamics, and fineness trends and Au-Ag zoning in gold grains.

Jan 1, 1990

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991

By K. V. Raj, A. T. Weakley, A. L. Miller, D. A. Parks

Diesel particulate matter (DPM) is a common and well-known health hazard in the mining environment. The current approved method for monitoring both the organic and elemental carbon (OC, EC) portions of DPM is a laboratory method with a turnaround time of approximately one week. In order to evaluate exposure levels and take corrective action before overexposures occur, a portable real-time device capable of quantifying both OC and EC is needed. To that end, researchers from the National Institute for Occupational Safety and Health (NIOSH) designed and tested a device based on narrow bandpass optical filters that is capable of targeting infrared absorbance bands associated with DPM. Five optical bandpass filters were chosen based on previous work quantifying DPM using Fourier-transform infrared (FT-IR) spectrometry. The resulting device, referred to as a filtometer, is optimized to exclusively determine DPM and could serve as a cost-effective, field-portable alternative to laboratory-grade FT-IR analysis and instrumentation. The performance of the filtometer was investigated by calibrating FT-IR data from DPM (dependent variable) to the filtometer spectra (predictor variables) using a partial leastsquares (PLS) and ordinary least squares (OLS) approach. The square of the correlation coefficient and root-mean-square error of cross validation m

Mar 2, 2022

By Christopher J. Pritchard

Federal mine safety regulations prohibit the recirculation of face air In a gassy Class III metal-non metal mine. Tg Soda Ash, Inc, operates a 2.0M ton/yr (2.2 million st/yr) underground gassy Class III trona mine In southwest Wyoming, currently liberating approximately 5,700 m3/day (200,000 ft3/day) of methane. Because of the low methane emissions and the incombustibllity of trona, it was decided that Tg would be an excellent environment to test recirculation at a U. S. gassy mine, for possible future use by Industry. A research program was begun with the cooperation of MSHA, the U.S. Bureau of Mines, the University of Utah, and Tg. Initial testing centered around re-using shop air under¬ground. Next, conduct a continuous miner section recirculation test to see how the face contamination was affected by 305m (1,000 ft) and 610m (2,000 ft) recirculation distances. A district test followed to examine the effects of the critical parameter - respirable dust. Finally, a long-term program to study respirable trona dust transportation and deposition in mine airways to plan for district fan siting and effects on face air dust levels.

Jan 1, 1995

By Randal J. Barnes

The January 1988 issue of Engineering and Mining Journal includes two short articles on blasting practices in surface gold mines (Anon., 1988 ; Carr , 1988). A reader of these articles learns, among other things, that a "12 x 13 ft" blasting pattern is used at the Carson Hill Mine, and a "17-ft burden and 18-ft spacing" is used at Echo Bay Mineral's Borealis operation, while at Mascot's Nickel Plate Gold Mine "ore shots are on a 10 x 10 ft" pattern. Like a new edition of the World Book Almanac, these articles are overflowing with useful tidbits of technical data; but, they never mention why the particular blasting patterns were selected. A survey carried out during the Winter of 1988 at six surface gold mines in the western United States also failed to produce a satisfactory answer. The responses from mine planning engineers to the question "why is your blasting pattern X by Y", reduced to "we use X by Y here because we used X by Y at our last operation, and it worked ok." Certainly, with the available decades of experience and professional practice in blast holes design, rock fragmentation in surface mines has been thoroughly investigated. However, and this is the central issue, fragmentation of the rock is not the primary purpose of most rotary drill holes in surface gold mines. Quoting senior mine engineers from companies operating, three of the richest surface gold mines in the world (AMAX Gold, Homestake Mining, and Gold Fields Mining)

Jan 1, 1989

By A. M. Elmherig, M. R. Sunu, R. N. Singh

The presence and orientations of fractures and discontinuities in rock masses exposed in a surface mining excavation are likely to have a great influence on both slope stability and blasting efficiencies. The classification of rock materials requires detailed investigations which are of interest to the design engineer. In designing a safe mining excavation, an engineer must take a number of decisions regarding face support and orientation based on the evalu¬ation of local strength and structural conditions encountered. The description of rock masses requires information additional to the properties of the rock material, discontinuities and other characteristics of engineering importance. Such information involves the acquisition of the following data: The description of the rock mass with reference to major geological structures. The orientation, nature, spacing and persistence of discontinuities. Degree of weathering. A critical review of rock mass classification systems and their application to surface mine excavation design and stability analysis is presented. The field investigation techniques for collecting rock mass data are described together with the techniques of analysis and presentation of data. Laboratory tests are carried out to determine intact rock strengths and deformation parameters of rock. The paper presents two case studies from the British hard rock surface mining industry to illustrate the application of the rock mass classification systems to stability analysis and excavation design.

Jan 1, 1986

By L. Barry Phelps

The complexity of surface mining operations is increasing as attention is directed towards mining larger tracts of lower grade, higher cost deposits. Large tonnage requirements from these mines necessitate utilization of many large pieces of equipment. This equipment must be utilized efficiently, with production maintained at or near designed capacities. Basically, the problem is to select, size, and schedule equipment to maximize profits and minimize adverse environmental impacts (Anon., 1977). The time, manpower, and cost limitations required to analyze a wide variety of situations and alternatives in planning surface mines have been sidestepped with the application of simulation methods using a digital computer. Since a simulator can be programmed to represent the situations which are to be analyzed, many alternatives can be evaluated in a relatively short time. Input variables are easily changed and the resulting changes which take place in the system can be analyzed. When standard methods of analyses are applied, weeks and many man-hours are involved in analyzing large-scale mining operations. At the same time many simplifying assumptions must be made since these operations are dynamic and transient. Hence, it becomes difficult to make sound engineering decisions and take proper and timely corrective action in the absence of simulation methods. This chapter is concerned with the application of one such method, namely, the open-pit materials handling simulator (OPMHS) developed by the Mining Engineering Section, The Pennsylvania State University (Manula, Albert, and Ramani, 1977).

Jan 1, 1979