Search Documents

By Fathi Habashi

OXIDE ORES can be divided into two groups: 1) Simple oxides (Table 3.1). 2) Complex oxides. Those ores containing minerals composed of two oxides; an acid oxide (Cr2O3, Nb2O5, etc.), and a basic oxide (CaO, FeO, MnO), as shown in Table 3.2.

Jan 1, 1970

By Dennis C. Drehmel

Because of their relatively low cost, carbonate rocks are desirable in abatement of air pollution by acid gases. Although many processes and types of equipment have been proposed to control or prevent the emission of acid gases, this paper considers only three: dry-limestone injection, wet-limestone scrubbing, and chemically active fluid beds. For the dry-limestone-injection process, surface area-especially from pores in the 0. 2- to 0.3-micron range-is one of the important parameters which will discriminate between less and more reactive carbonate rocks. Marls, chalks, oolitic calcites, and other fine- grained limestones show larger-than-average surface areas and better- than-average removal efficiencies. Inert chemical impurities such as silica detract from reactivity. A dolomite is not necessarily less re- active than a calcite. For the wet-limestone-scrubbing process, dissolution rate of the carbonate rock controls the differences in stone reactivity. In this process the dolomites are less reactive than the calcites. In addition, more than 90 percent of the dolomitic impurity in Fredonia white lime- stone is inert during limestone scrubbing. Dissolution rate is also a function of particle size for large-grained carbonate rocks. Fine grinding of such rocks will increase the dissolution rate to that of a fine-grained rock. Hence the requirement of high dissolution rates may be met by some grinding of fine-grained material (e. g., marl, chalk, or other limestone) or by fine grinding of coarser grained material. For chemically active fluid beds, chalks have the best capacity to absorb both SO2 and H2S. However, most chalks are probably unsuitable for fluid beds because of high attrition rates. Because dolomites are generally more reactive than calcites with both SO2 and H2S, a dolomite would be the feed material of choice for a chemically active fluid bed.

Jan 1, 1974

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By Glenn A. Gruber

The conditioning of phosphate flotation feed with anionic flotation reagents was identified as a high- priority research topic during a beneficiation work- shop sponsored by the Florida Institute of Phosphate Research (FIPR). FIPR subsequently solicited research proposals to identify the mechanisms of reagent adsorption, to determine scale-up relationships for conditioner design, and to investigate the effect of conditioning variables on reagent adsorption and flotation performance. The two-year research project was awarded to Jacobs Engineering. Somasundaran, Inc., the University of Florida Mineral Resources Research Center, and the U.S. Bureau of Mines assisted Jacobs. Two mechanisms of anionic collector adsorption were detected by spectrographic analyses and confirmed by microcalorimetric measurements. The mechanisms provided a sound technical basis for the empirical practice of conditioning phosphate flotation feed at a high percent solids. Tests performed in laboratory and pilot-scale agitated tanks indicated that power intensity may be used as a reliable scale-up parameter for anionic conditioning of phosphate slurry. Excessive agitator speed during conditioning was found to be detrimental to anionic flotation performance. Some dimensional ratios of anionic conditioners were found to be consistent with good utilization of agitation energy. Laboratory conditioning and flotation tests demonstrated that adsorption of collector onto phosphate and the subsequent recovery of phosphate in anionic flotation were significantly influenced by the quantity and quality of water used in conditioning. Conversely, the quality of water used in flotation was more influential on the recovery of quartz in the concentrate. A comprehensive survey of anionic conditioners and conditioning practice in the Florida phosphate industry was also performed during this project. The study clearly showed that flotation testing with laboratory conditions typical of scientific research gives different results than laboratory testing with simulated plant conditions. The effects of test conditions on laboratory test results should be carefully considered by investigators planning and conducting applied research.

Jan 1, 1999

By U. Paschedag

Today's modern longwalls have to produce high outputs with maximum availability and running time with the additional requirement of ever increasing panel width and length high-performance face conveyors require intelligent solutions for the integration of drive systems and chain tensioning devices into the overall longwall automation. The fully automated chain tensioning system allows the operation of an AFC with optimum chain tension at all times regardless of actual load on the conveyor. For the heavy-load start-up, the accurate load-sharing and an efficient overload protection of modern AFC's WESTFALIA and Dodge jointly developed the integrated WB/CST drive system.

Jan 1, 1995

By A. Ang-Ug, L. Gurieff

"The Phu Kham Cu-Au mine in Laos is owned and operated by Phu Bia Mining Limited. The deposit is a complex and low grade Cu-Au porphyry ore. The rougher feed has a particle size distribution of 80% passing 110 µm, and the rougher concentrate is reground for cleaning to 80% passing 25 µm. The Cu losses in the cleaning circuit are primarily in the <12 µm fraction. A randomised paired ON-OFF test of magnetic conditioning in one of the two parallel cleaner 1 circuits was undertaken. The results showed that with magnetic conditioning there was approximately a 10% reduction in the <12 µm Cu distribution in the cleaner 1 tail to a 98% level of confidence. The Cu distribution in the <12µm fraction is a less variable measure of changes in the <12µm Cu recovery, therefore, this was used to evaluate the impact of magnetic conditioning. Subsequently, magnetic conditioning was installed in both cleaner 1 circuits and the plant results monitored after this installation. Comparing the plant results immediately before and after this installation showed that there was a 20% reduction in <12µm Cu losses to the cleaner tail. INTRODUCTION The Cu-Au, Phu Kham Mine (PKM) is located within PanAust's Phu Bia Mining Contract Area in Laos, approximately 140 kilometres from the capital city, Vientiane. PKM is PanAust's flagship operation and the significant cash flow generated by PKM has supported PanAust’s growth, while contributing to a strong balance sheet. PKM comprises an open-pit mine and a conventional milling and flotation operation that produces and exports a Cu and precious metals concentrate. The concentrate contains around 23% Cu, 6 ppm Au and up to 35 ppm silver. Process Overview The PKM deposit consists of complex heterogeneous mineralogy horizons of Cu-Au stockwork and skarn mineralisation. It contains areas of soft-leached zones, overlying transition zones and supergene chalcocite dominant secondary Cu mineralisation and clay-rich gangue. Areas of high As and Zn also pose a challenge in treating the highly variable ore. In addition, hardness of the ore increases with deposit depth. The ROM is hauled to a primary gyratory crusher to produce a coarse ore stockpile with size distribution suitable for the 13 MW semi-autogenous mill. The SAG product feeds two parallel ball mills each equipped with a cyclone cluster producing a product particle size distribution of 80% passing 110 µm. The conventional flotation circuit consists of two parallel rougher banks. The rougher concentrates feed the regrind cyclone where the underflow is split and reports to two parallel, 3MW, M10000 IsaMills. The regrind mill discharge combines with the regrind cyclone overflow with a product particle size distribution 80% passing 25 µm and reports to the Jameson cell."

Jan 1, 2018

By Fathi Habashi

WHILE HYDROGEN SULFIDE precipitates metal sulfides from aqueous solutions, other gases such as sulfur dioxide, carbon monoxide, and hydrogen, under certain conditions, precipitate the metals directly. This can be achieved at high temperature and pressure. Such processes are of great technical importance, since metals of high purity are precipitated economically in a powder form. As a result of the availability of such powders on a large scale. processes for compacting metal sheet and other mill forms directly from the

Jan 1, 1970

By Lawrence Adler

[An innovative framework is proposed which most efficiently and systematically handles the large quantity of information needed for equipment failure and other non-performance analyses. It is based on the accepted engineering dimensions of mass (material), length (geometry), and time (MLT). To these are added human and machine factor. Several failure "Modes" are identified for each dimension, which are then subdivided into specific "Types". Material Failure Modes such as Separation and Slip are easily recognized, but others had to be established. Geometric Failure Modes are usually straight-forward, Obvious ones include Geometrics Design and Stability with more synthesized. Time Failure Modes are again largely self-evident such as Life and Chemical Effects, others are needed. Human and Machine Factors as failure modes are loosely assembled. The results contain strengths, but also organizational weaknesses which are noted. Lacking a better alternative its use is recommended.]

Jan 1, 1989

By Y. H. Alghamdi, A. D. S. Gillies

"INTRODUCTION Background Diesel Particulate Matter (DPM) has been a critical issue during the last decade in underground mines. This problem is threatening the health of mine workers, as well as the mine’s productivity. It has been confirmed that the diesel engine exhaust is the main source for the diesel particulate matter (DPM), and that it has the highest impact in raising carbon monoxide, carbon dioxide, oxide of nitrogen, and hydrocarbons in the underground environment. Miners who are exposed to this kind of emission are at high risk for developing lung cancer and other lung diseases. The Mine Safety and Health Administration (MSHA) has issued standard rules to regulate diesel emissions in underground mines. The final ruling confirmed in 2008 that the total carbon should not exceed 160 µg/m3. (MISHA, 2008) Monitoring DPM in underground mines has become important to ensure compliance with the MSHA regulations. There are many different types of DPM monitoring systems that are currently being used in underground mines. Two methods are typically used for DPM sampling: the personal sampling method or the direct exhaust sampling method, which takes a direct sample from the engine’s tailpipe. Many mines do not recommend using the direct exhaust sampling method since it involves complex measuring equipment and procedures, as well as it is not regulated in the United States or Canada. Thus, the personal sampling method is the preferred method in many mines when taking DPM samples. Even this method includes many variations, such as the Respirable Combustible Dust (RCD) method and the method devolved by the National Institute for Occupational Health and Safety NIOSH 5040. The NIOSH 5040 method is the preferred method overall because it gives more accurate measurements compared to the other methods. This method does not allow organic carbon sources other than those coming from diesel engine exhausts to interfere with the measurements, which otherwise would lead to overestimating the actual amount of the DPM in the mine environment. An impactor feature in the cassette, which holds the samples in the instrument, characterizes this method. Since the diesel particles are less than 0.9 micron, this impactor does not allow particles more than 0.9 microns to be collected in the cassette filter. The cassette is then analyzed in a lab and the concentrations of organic carbon (OC), elemental carbon (EC), and total carbon (TC) are determined. Lately, the National Institute for Occupational Safety and Health (NIOSH) has developed a new instrument that can use the same concept of NIOSH 5040, but with instant measurements of elemental carbon. It utilizes laser radiation with the cassette so it can give a real time measurement. The real time measurements give instant information about the underground environment that will allow the mining engineer to take immediate action and enact plans instead of waiting for results from the laboratories where NIOSH 5040 method may take several weeks to get the measurements."

Jan 1, 2016

By Jim Salley, Mohammad Saleem, Indra Banerjee, Kevin Sapp

"On underground construction projects, effective Quality Management is essential for ensuring facility durability, life cycle performance and low maintainability. Furthermore, follow on contracts also rely on an effective quality management system for interface congruency. An effective Quality Management System (QMS) is also essential in mitigating risks and meeting schedule and budget performance objectives. For the past 15 years Central Puget Sound Regional Transit Authority’s Link Light Rail extension has successfully completed over 10 miles of twin bore tunneling and associated underground features including cross passages, deep sump structures and shafts. After the completion of each segment, lessons learned have successfully been implemented to improve the quality of delivered projects. This paper presents the Sound Transit QMS with regard to a number of project elements of tunnel construction projects, with specific focus on quality performance of slurry wall construction, TBM tunnel excavation assessment, segment production and segmental lining installation, and other associated construction features. A collaborated total QMS will be presented in this paper that will serve as a guide for successful implementation of Quality Assurance and Quality Control processes. INTRODUCTION Implementation of a robust Quality Management System reduces defects, errors and omissions, identifies and addresses nonconformance in a timely manner and increases stakeholder confidence in the project. In fact and effective QMS helps ensure that optimal project outcomes are realized both in terms of project delivery and life cycle performance. The two key components of QMS are quality control and quality assurance. Quality Control (QC) is the procedure implemented to achieve a certain level of quality and ensure that products, processes and services meet specific requirements. Quality Assurance (QA) activities are carried out to evaluate the effectiveness of the quality control measures and ensure that the QC process is working. A team obligation that recognizes that quality is built into every aspect of a project is the basic concept of a successful QMS."

Jan 1, 2016

By R. O. Burt

Gravity concentration - the separation of minerals according to their relative density - is one of the oldest forms of mineral processing. Even though modern technology has developed a range of other processes, gravity concentration remains as one of the most important methods employed for mineral separation. The range of minerals recovered covers a wide spectrum, from andelusite to zircon, from coal to diamond, from gold to industrial mineral. The long history of gravity concen¬tration, along with a still imperfect understanding of the various mechanisms involved has resulted in a series of ingenious engineers developing, some¬times perfecting and sometimes rejecting, a wide range of equipment, suited for a variety of different duties. &apos;Selection&apos; in the context of gravity separation, is primarily the choice of the right type of equipment for the separation in hand; &apos;sizing&apos; of the correctly chosen unit is, more often than not, determining the appropriate number of units required to suit the throughput. The accent of this chapter will, therefore be &apos;selection&apos;. A brief description of the major types of gravity concentration equipment will follow a discussion of the factors which determine the selection of the correct unit. CLASSIFICATION OF GRAVITY CONCENTRATION EQUIPMENT All concentration equipment has a primary function and a secondary function. The primary function is the efficient separation of the constituent minerals into two or more discrete phases; the secondary function is to effectively cause the discharge of these discrete phases into separate compartments (Aplan 1975). For maximum efficiency of operation, the forces which effect the primary function should not also result in the secondary function occurring; in such cases optimum operating conditions required for the primary function, separation, may have to be compromised to ensure reasonably efficient operation of the secondary function, product discharge. With gravity concentration, the primary function is effected by the relative movement of minerals of different density in response to gravity and one or more other forces, the latter often including the

Jan 1, 1986

By David Hurth

JOHN HAMRIC: Our next topic leader is David Huth, superintendent of sulfuric power generation, DAP, and shipping for IMC-Agrico, Nichols Plant, Mulberry, Florida. With a title like that it&apos;s no wonder he believes in empowerment. His topic today is "The Triumphs and Pitfalls of Using Empowerment Techniques." DAVID HUTH: Empowerment and its benefits are a desirable alternative to the traditional management structure. The difference between the two is the amount of decision- making authority and responsibility given to individuals by a supervisor. Just what is empowerment and how does it work? Empowerment is relinquishing to individuals the authority and responsibility to make daily decisions. Can everyone be empowered? What if they make a wrong decision? Will I empower myself out of a job? These are questions that all managers have when they hear the word empowerment. In today&apos;s fast-paced and high-pressure business environment, the old way of managing people must be replaced with a new approach. No longer can we, as managers, make all the decisions. The increased work loads due to downsizing, consolidation, and synergies have stretched us too thin. What about our employees? How can we motivate them into the high-performance teams that our companies are demanding? What possibly could satisfy both these issues? The solution to these problems can be solved with the power of employee empowerment. Employee empowerment will not only lessen the load on managers but will build teamwork, motivation, and pride into the employees who work for the managers who use it. American business was rudely awakened in the early 1980s when the Japanese companies not only caught up to American companies but literally flew by them. America was fat, dumb, and happy after World War II. Why wouldn&apos;t they be? They had all the factories. Everyone else had to rebuild. So for 40 years American business lounged in the limelight of very little true competition. But times change. Unfortunately, American business did not. Now the cry to perform in the new global economy has come down from the corporate boardrooms. Down through the ranks it has been felt. Guess who is supposed to make it work? But where are all those people who are going to make this rejuvenation and corporate renaissance possible? Many of them are gone-lost in downsizing, synergies, and rightsizings

Jan 1, 1998

By Robert M. Belesky, H. R. Hardy

A methodology to detect the presence and monitor the stability of shallow cavities is presented in this paper. The approach incorporates surface-wave seismic and acoustic emission/microseismic (AEIMS) techniques. Application of tomography to the seismic data is made to enhance the ability to locate cavities. Zonal and hit-sequence location techniques are introduced into AE/MS monitoring schemes. These source location techniques simplify the analytical procedure yet still provide sufficient information regarding the region of AE/MS activity. The concept of unique velocity data for conventional, least-squares, source location routines is discussed. A hypothetical case utilizing the algorithm is presented. The method described has been successful based on preliminary studies. Areas of current and future research are identified.

Jan 1, 1986

By Roderick G. Eggert, John E. Tilton

During much of the 1970s and 1980s, world metal consumption grew more slowly than during the 19505 and 1960s. The slowdown contributed to surplus capacity and low real prices because actual consumption was consistently less than expected as new mining and mineral processing capacity came on stream. Over the last year or so, however, world metal consumption has picked up noticeably, raising the question, Has metal demand returned to the long-run growth rates more typical of the 1950s and 1960s than of the 1970s and 1980s? This paper examines this possibility and, more generally, assesses the factors that will shape demand for the major metals over the longer term. TRENDS IN METAL CONSUMPTION The extent to which metal consumption has recaptured the brisk growth rates typical of the 1950s, 1960s, and early 1970s is shown in Figure 1. This figure traces the consumption of crude steel, primary aluminum, refined copper, refined lead, and refined zinc between 1960 and 1987 for the western world, consisting of the OECD countries (including the United States), and the developing countries. Consumption increased in 1987 for all five metals, and preliminary data for the first six months of 1988 suggest even more substantial increases, at least for the United States (U.S. Bureau of Mines, 1988). However, Figure 1 also shows that the recent increases in consumption are not untypical of similar surges during earlier periods of economic expansion and thus may reflect only cyclical or temporary factors. In short, the available data are unable to provide a clear indication of whether recent increases in metal consumption reflect the beginning of a new era of faster growth or simply a cyclical and temporary upturn associated with the expansionary phase of the business cycle. Consequently, to pursue this issue, we are forced to examine the underlying forces that will shape metal demand trends over the next decade. The approach we have taken involves two steps. The first examines the prospects for overall economic growth. The expectation is, the faster the economy expands, the faster the production of metal-containing goods grows.2

Jan 1, 1989

By Edward D. Elkins

CalMat Co. is one of the largest producers of construction aggregates in the United States. The CalMat Reliance plant is located in Irwindale, California, and is situated on an alluvial fan formed by the San Gabriel River. The fan deposits are of Quaternary age and were derived from granitic and metamorphic bedrock exposed in the San Gabriel Mountains to the north. The sediments are poorly sorted and range in size from large boulders to clay size particles. The coarse material is hard and durable and consists of quartz diorite, granodiorite, granitic gneiss, schist and minor amounts of volcanic rock. The matrix is comprised of silty sand with varying amounts of clay. Thin silt and clay lenses occur sporadically throughout the deposit. The clay content of the matrix and the degree of weathering of the coarse material increases with depth. Based on seismic data, the alluvial fan varies from 200 to 400 feet thick and overlies crystalline bedrock. The Reliance plant was constructed in 1971 and 1972. It has a nominal capacity of 1200 to 1400 tons per hour, and typically produces more than three million tons of aggregate products per year. Alluvial fan sediments are mined from a gravel pit situated adjacent to the plant. The material is fed through a mobile, 48- by 60-inch, in-pit jaw crusher, then transported by conveyor to the main plant to be processed. The plant is modern and highly efficient. It has a typical wet and dry circuit and is capable of producing a wide range of aggregate products. To extend the life of the plant, a 9,000 foot conveyor system is being constructed to connect it to a granite quarry operated by Azusa Rock Inc. The quarry is located north of Irwindale, and is 50 percent owned by CalMat Co. The conveyor will be used to export crushed rock from the quarry to Reliance. The existing plant will be modified to process the crushed rock.

Jan 1, 1995

By J. D. Miller, J. Hupka

Environmental applications of the air-sparged hydrocyclone (ASH) technology are presented. The original ASH design used porous sintered steel or porous polyethylene tubes as spargers. To diminish/prevent plugging and to reduce pressure head loss in the gas path a wire screen sparger and new hydrocyclone design have been developed, which allows for wide application of the technology to solve environmental problems and to be used as a chemical reactor. Field and laboratory trials have shown that the ASH technology might be preferred for the stripping of volatile organic compounds WOC) from contaminated water. The ASH has also been developed for absorption of SO2, toluene vapors, and for the recovery of cyanide.

Jan 1, 2005

The successful exploration for Austin Taylor and Gen. McRae from 1931 to 1940 obscured the fact that I was reaching a period of transition. This was true both in personal and business life. It was probably fortunate that I did not realize how great a change must come after I passed the age of 50. In the personal life of our family the change came when both our children left home to go to school or college. This made home a different place and, because of the absence of the children, Dorothy could devote much of her time and attention to the art she loved so well. She could spend long periods in New York, the center of the nation&apos;s art life. Vacations at Tahoe and long pleasure trips made the separation from the children less disturbing but it could never again be the same as it had been in the first 20 years of our marriage. The change In my business life was just as complete, though a little more gradual. While work for Bralorne and General McRae made the "bite" of the Great Depression less painful for us than it was for most consultants and their families, the fact that I was getting older made a new sort of work inevitable. I was 50 years old and the total grew rapidly. Planes and automobiles that made travel easier even in the wilds of Alaska and northern Canada still made it possible for me to look at new prospects, but increasingly often I was exhausted at the end of a day&apos;s climb and, if the nature of my work did not change there would soon be no more work. Fortunately work of a new sort came a little at a time. As I became a director of Bralorne and president of its American subsidiaries I had to take on more administrative work, and success of these operations made others want to employ me to help direct policy and value mines. I was also asked to arbitrate contests between mines when technical disagreements were so great that judges or juries could obviously not understand them My consulting for government agencies helped to

Jan 1, 1976

By Raymond E. Langen

Uranium exploration in the Powder River Basin of northeastern Wyoming has been intensive since 1966 and in 1968 produced significant discoveries of reduced uranium ore by Humble Oil & Refining Company and others. Substantial reserves have been established in the area. High-grade carnotite ore was discovered in 1951 near Pumpkin Buttes in the central part of the basin (Fig. 1). Other mineralized areas were soon established from Pumpkin Buttes south to Monument Hill and Box Creek. Total production from these shallow oxidized deposits in the lower Eocene Wasatch formation was small. The AEC reports total production of 520,000 tons of ore averaging 0.19% U3O8. The authors are indebted to many people within Humble Oil & Refining Company and Esso Production Research Company for their assistance and guidance. SUMMARY AND CONCLUSIONS The Highland ore deposit, discovered in 1968, is a large uranium occurrence located in the southern part of the Powder River Basin. Uranium mineralization consists of sooty, black uraninite and coffinite coating sand grains and is concentrated along the margins of Tertiary fluvial sandstones. Uranium was transported by oxidizing solutions roving through the buried sandstones and spreading into less permeable channel-edge sandstones to form typical rolls and tabular deposits. Unaltered sandstones are light gray to gray-buff where the sandstones have been oxidized, the colors are various shades of red, yellow, and yellowish brown. An Oligocene tuffaceous source for the uranium is proposed; however, leaching of the arkosic and tuffaceous host sediments may also have provided a source.

Jan 1, 1971

By John Rushton

Surface mining, from ore extraction to processing, requires many types of equipment to obtain the final product. Mine equipment often includes shovels, drills and haul trucks. Ore processing equipment, including plants, mills and concentrators, are also part of surface mining operations. Surface mining operations emphasize production. Production is where the bills are paid and fortunes are made. However, there must be support to keep the equipment operational. To most production people, equipment maintenance is a necessary evil. Maintenance is not glamorous work. It is often neglected when praise is being passed around. It is easy to recognize higher production, greater capacities, faster cycle times or more loads hauled. But who cares if an engine is replaced in 12 hours instead of 48? The answer is, everyone should - from the hourly miner to the mine manager. Surface mining equipment needs constant maintenance work. It must be lubricated, components replaced, electrical problems repaired and other problems addressed. Repair work for any surface equipment takes time away from production. It costs money. Maintenance costs cannot be avoided. However, they can be minimized. Minewide communication should include operations cooperating with maintenance. Traditionally, operations resist surrendering equipment to maintenance if it can continue to produce. The rationale is, every load that can be hauled today is money in the bank. If the unit is taken down, the money is lost. This thinking is prevalent in many surface mining areas, including the mill. "Not on my shift," the operator thinks. "Let the next crew worry about it. The problem with this thinking is in probability and statistics. The longer equipment goes without maintenance work, the higher the probability of equipment failure. When the failure does occur, it is certain to cause the equipment to remain down longer than if the maintenance department had been allowed to take it down. Many mining operations have closed early in their lives because of poor maintenance practices. This has become the industry standard because substandard levels of performance are acceptable. Management believes it gets five to six hours of work from maintenance people during an eight-hour shift. Actually, the industry average is less than two hours of work per shift. Real productivity levels of less than one hour are not unusual. There are few exceptions. However, a daily work schedule (DWS) will increase productivity at many properties by 50% to 100%. A 200% improvement is not unusual. The DWS will work. Maintenance people are among the most intelligent and motivated people on the property. They deserve the chance to be productive. [ ] In preparing a DWS, management needs to understand two productivity principles - the productivity spread and the real maintenance workday.

Jan 1, 1997

Drainage and erosion control often become problems at mine reclamation projects. An example of this was an abandoned surface uranium mine on the south Texas plains. Engineers with the Texas Railroad Commission solved these and other problems with a three-dimensional geomatrix erosion-control matting at the 69-hm2 (170-acre) site, about 70 km (45 miles) southeast of San Antonio. Enkamat, manufactured by Akzo Nobel Geosynthetics, was installed to reinforce the grass waterways that handle runoff from the reclaimed mine. Reclamation was completed in the spring of 1992. Bill Walker is regional manager for Erosion Control Systems. He worked with the contractor to identify an erosion control product that complied with the project&apos;s design and installation parameters. "Use of erosion control matting enabled us to reduce erosion control costs," said Mark Rhodes, with the Texas Railroad Commission. "Also, the erosion control material was more aesthetically compatible with the reclaimed landscape." The commission&apos;s design called for a terrace ditch to be constructed midway up the reclaimed spoil slope to catch and collect water. Commission engineers selected spoil slopes, ranging from 5% to 8%, to build reinforced grassed waterways to drain the collected water from the terrace ditches. This was done instead of dropping the water at steeper slope location in rip rap- or concrete-lined channels. Enkamat&apos;s three-dimensional geomatrix of heavy nylon monofilaments is 95% open space that aids root growth. Its root-reinforcement system resists the hydraulic lift-and-shear forces created by high-volume discharges of water. In addition, fine eddy turbulences are prevented from isolating and uprooting individual roots and clumps of vegetation. Enkamat is flexible and lightweight. This makes it easy to install. And, because grass grows into it over time, it "disappears" after installation. Between 12,540 and 14,200 m2 (15,000 and 17,000 sq yds) were installed in the waterway using 150-mm (6-in.) staples to fasten the matting, said contractor Dale Blackstock. "It was easy to use; no problem at all to put down." Blackstock selected Enkamat from a list of eight different channel lining materials described as acceptable in the commission&apos;s design specifications. The design specifications were based on the results of channel-lining performance tests conducted by the Texas Department of Transportation. Rhodes said that the commission&apos;s Abandoned Mine Land Reclamation program had installed Enkamat on other abandoned uranium mines and on an abandoned surface lignite mine near Austin. "Pretty much all of our installations of Enkamat have worked out well," he said. "There have been no failures. The reinforced grass waterways have performed as designed."

Jan 1, 1998