Search Documents

By Richard H. Adams

INTRODUCTION With the discovery and depletion over the years of near surface ore bodies, exploration targets are tending to be at greater depth or overlain by various types of overburden which in some cases extends to considerable depth or is heavily water bearing. Access to these types of deposits for exploration and development often requires vertical shafts. This paper discusses the concept of small shaft engineering and construction, primarily for underground exploration but also for use as a low tonnage production facility or for mine ventilation. The option of a small shaft may be attractive in a number of cases, some of which are: The underground exploration of a deposit at depth where minimal expenditure is desirable until the potential of the deposit has been determined. The exploration shaft in many cases later serves as a ventilation way and second means of egress. Production of ore in a small tonnage/high-grade operation where decline access is impractical. For ventilation where other types of openings are impractical or would delay start-up of mine operations.

Jan 1, 1987

By J. M. Mutmansky, Y. J. Wang

The method usually used to predict the direction of flow in a connecting airway is to conduct a survey of the two existing nodes to be connected by the new pressure airway. It is then assumed that the air will flow from the node with the measured higher pressure to the node with measured lower pressure. This paper examines this direction-of-flow problem using properties of the system characteristic curve for a two-terminal network and specifies some conditions that will ensure that the air will flow in the direction anticipated. It was concluded that the only requirement is that all characteristic curves of the fans in the network should be strictly decreasing. Five numerical examples illustrate some important proper- ties of the direction-of-flow problem.

Jan 1, 2000

By J. Maiti, A. Bhattacherjee

A literature review on quantitative analysis of mine safely studies revealed that numerous investigators explored a wide- range of techniques, including the investigation of bivariate and multivariate statistical models. Although these researchers addressed various issues of accident causation and prevention, they, in general, did not investigate through the use of quantitative models the multivariate relationships of several factors affecting mine safety in a causal framework. In this paper, systems dynamics and structural equation modeling are presented to simultaneously represent and study the effect of policy variables related to accident prevention along with the factors causing accidents and injuries. The application of these models to a group of mines revealed that current training practices at these mines do not appear to alleviate accident occurrences. It is inferred that the use of these quantitative techniques can provide a new direction of research in mine-safety studies.

Jan 1, 2000

By Gerald H. Luttrell, Joe Shoniker, Jaisen N. Kohmuench, Christopher J. Barbee, Michael J. Mankosa

The HydroFloat technology was specifically developed to upgrade phosphate sands that are too coarse (>0.6 mm) to be efficiently recovered by conventional flotation methods. In this novel process, classified feed is suspended in a fluidized bed that has been aerated using an external sparging system. The air bubbles selectively attach to particles that have been made hydrophobic through the addition of a fatty acid collector. The teetering effect of the fluidized bed forces the low-density bubble-particle aggregates into the overflow, while hydrophilic particles are rejected as a high solids content underflow Since the HydroFloat is actually a density separator, the process can treat much coarser feeds than would be possible using traditional flotation processes. In addition, the high solids content of the teeter bed promotes bubble-particle attachment and reduces the cell volume required to achieve a given capacity. This paper presents test data from ongoing pilot-scale trials of the HydroFloat cell in the phosphate industry.

Jan 1, 2002

By M. J. Sanzotti, C. J. Bise

This paper examines the potential for controlling longwall-induced subsidence by pneumatically backstowing waste rock into the void created by mining. The paper also examines scheduling the process as a unit operation of the mining activity. Based on a review of background literature and interviews with representatives of various mining companies, public-interest groups and state and federal regulatory agencies, a hypothetical case-study evaluation of pneumatic stowing at a southwestern Pennsylvania mine was conducted. The study indicated that current stowing technology cannot keep pace with the production potential of longwall systems in the United States. Further, at the mine used in this case study, concomitant stowing would reduce subsidence by only 50% of what would normally be incurred during full longwall caving, and the longwall coal-production rate would decrease from 3,630 t (4,000 st) per shift in the nonstowing case to 1,360 t (1,500 st) in the stowing case. A preliminary cost analysis reveals that pneumatic stowing would add from $5.79 to $11.57 per t ($5.25 to $10.50 per st) to the operating cost of producing coal at the case-study site.

Jan 1, 1997

By Munson R. McKinney, Bryan A. Slim

To date some 1,000 exploration targets (by way of adits, mine dumps, shafts, outcrops and unstoped mine areas) have so far been identified using an interactive data base system to query a digital data base comprising topographic, cadastral geological and mine components developed as a compilation of old plans, records, surveys and recently flown aerial photography. The exploration targets are intended for early follow-up as part of a 1987 exploration programme to investigate the reserve potential of the former producing property located in southern Utah. Of further interest is the unscrambling of old mine plans to provide drill targets for investigation of unstoped reserves with one target being a possible 800,000 tons in part of the lower workings. The project site encompasses about 3,200 acres of mainly patented lode claims covering most of the claims and mines of the Gold Mountain mining district formed in 1889. Turn of the century mining saw several mines operating whose total production was at least 143,000 oz. gold and 460,000 oz. silver from steeply dipping veins up to 20 ft. or more in thickness.

Jan 1, 1987

By J. T. Sitarski, R. C. Emmett, L. W. Luinstra, R. P. Klepper

A mining operation in Zimbabwe produces a pyritic gold concentrate that requires oxidative pretreatment prior to cyanidation in order to liberate 80 percent of the gold values. Bio- oxidation offered the potential of increased gold recovery and was considered to be an economically advantageous alternative to the existing practice of roasting the concentrate. Based on bench- scale test work, a small bio-oxidation plant, capable of processing approximately 50 percent of the concentrator production, was installed at the mine to evaluate this approach. The plant included two 57 m3 bioreactors in series and the ancillary equipment needed to prepare the feed concentrate, to wash the leached residue prior to cyanidation, and to neutralize the waste liquor. The plant was operated for a year-and-a-half, and the conditions needed to achieve a 90 percent liberation of gold values were determined. A number of critical technical problems were encountered, and many were resolved on-site. Others have been addressed since the pilot plant was moth-balled in June 1988. Valuable insight was gained from the operation of the pilot plant, which has provided useful guidance for continued process and equipment improvement.

Jan 1, 1990

By J. F. Stenebråten, W. P. Johnson, D. R. Brosnahan

Carbonaceous materials (CM) from ores of varying preg¬robbing activity from Barrick Goldstrike Mines Inc. (BGMI), Nevada, were characterized in terms of their functional group contents, hydrocarbon contents, elemental composi¬tions and humic acid contents. Fourier transform infrared (FT-IR) analyses did not show the presence of hydrocarbons or carboxylic, phenolic or sulfhydrolfunctionalities. The FT¬IR bands present included C=C stretching in aromatic rings and C-O-C stretching, indicating the presence of oxygen as ether linkages or thiocarbonyl functionality in the carbon matrix. Calculated atomic oxygen to carbon (O/C) ratios did not reveal a trend between the maturity of the CM and the preg-robbing behavior, possibly due to the low resolution inherent in electron microprobe analyses. However, the atomic O/C ratios agree with other chemical analyses, indi¬cating that the organic carbon is very mature, similar to or higher than anthracite grade coal. Gas chromatography¬mass spectrometry and nuclear magnetic resonance analy¬ses corroborated the relatively featureless character of the carbon, indicating that the carbon structure is virtually completely aromatic (graphitic).

Jan 1, 2000

By Peter H. Grimley

It is important to realize that lending institutions have a very different risk-profile from that of an equity investor. For bank financing, a feasibility study must address the concerns of the lender and these can be summarized under the four 'PI Is: Project, Performance, Product and People. Generally, feasibility studies focus on the measurable project risks associated with a new venture, but frequently insufficient emphasis is placed on key risk areas such as ore grade and metallurgical recovery. Before accepting full or even partial non-recourse risk, financial institutions will demand evidence that the project was constructed according to specifications and within budget and that its Performance within agreed limits has been demonstrated. Product risk should be discussed in detail in any feasibility study. For industrial minerals, penetration of the market can be critical to success and for commodities with volatile prices, the sensitivity of the cash flow to a range of prices should be carried out. Methods of reducing price risk such as long term contracts or, in the case of gold, forward selling should be carefully evaluated. The People risk is rarely discussed in feasibility studies, but can be a key element. Few projects turn out to be faithful copies of the study and the ability of the operator to identify

Jan 1, 1988

By Raymond J. P. Brouzes

INTRODUCTION [A Decade After the 1972 Stockholm Conference] The UN-sponsored Stockholm Environmental Conference held just over 10 years ago was the first successful attempt to achieve global recognition of environmental issues. Indicative of the lack of concrete involvement in environmental protection to that time was the fact that only 15 nations had a department or ministry responsible for environmental affairs compared to today's 143. Many governments were uncertain of what were the most serious or pressing problems in their country. There was obviously a need to both identify those issues and to determine how to manage them once identified. At the same time, the public at large was becoming more critically aware that environmental protection had been neglected by government and often ignored by industry. It soon became evident that large amounts of money would have to be spent to redress some of the more evident problems. However, many developing nations were reluctant to slow down the much-needed industrial growth by imposing costly environmental controls on industry. In fact, some waived environmental control altogether as an incentive to attract industry. In some sectors, it was often stated that industrial development and environmental protection were mutually exclusive activities. The need of an awareness, commitment and dedication by all sectors of society to protect their environment was just beginning to develop, replacing the rather simplistic view that all environmental problems were caused by greedy industry.

Jan 1, 1984

By Kadri Dagdelen

Production scheduling of an open pit mine is one of the most important steps in open pit mine planning. The production schedule of a mine defines the distribution of cash flows and as a result directly influences the net present value and overall economic feasibility of a project. It is becoming more and more critical to obtain an exploitation schedule of a deposit such that highest possible returns are achieved from a project. As the mining industry mines lower and lower grade ores, production scheduling is becoming a key item which can make or break a project. Although the need to plan and operate a mine with an optimum production schedule has been obvious for some time, the methods used to obtain such a schedule have not been. There is not a single, mathematically proven, optimum mine production scheduling algorithm which is widely accepted and used today. In an attempt to determine a production schedule which is optimum, a new algorithm was developed. This algorithm, in theory, is based on the lagrangian concepts of mathematics and in practice is based on the parameterization concept of mining. This paper describes the fundamentals of this newly developed algorithm.

Jan 1, 1986

By John M. Wootten

The development of new coal markets is -t upon the ability to utilize coal in an environmentally acceptable and economically viable fashion. Foremost in the concerns about coal utilization is the impact its combustion has on air pollution. Concerns over environmental issues, such as acid rain, are currently one of the major impediments to the development of new coal markets. The Department of Energy and the Synthetic Fuels Corporation are addressing certain aspects of the development of new technologies for the utilization of coal. However, at the present time, there is a void in the new technology development process. That void is the step from proof- of-concept to commercial demonstration. Congress has established the Clean Coal Technology Fund at a level of $750 million to fill this void. The Department of Energy, in a solicitation of interest, received over 175 proposals for commercial demonstrations of clean coal technologies. A review of these solicitations indicates that $1.2 billion worth of research could be accomplished with a federal cost sharing of $425 million or 35 percent of the total. Industry has indicated, through this response, its willingness to invest its limited funds on projects it feels have the greatest potential for the clean use of coal. What must now occur is that Congress must appropriate the monies from the fund to initiate the commercialization of these clean coal techno1ogies.

Jan 1, 1986

By Joseph W. Kupfner

It is a recognized fact that a good maintenance program is a pre-requisite for minimum delay costs and maximum availability of equipment. To develop such a program and to make it effective, one must establish detailed instructions pertaining to inspections, lubrication, servicing, and/or replacing of various parts. A schedule must also be established for these maintenance checks, whether they be weekly, monthly, or whatever period is essential for the equipment. The number of tasks to be performed becomes monumental, and the administration is beyond error-free human capacity. It is for this reason that the computer must be an essential element in any efficient and economical preventive maintenance program. The evolution of a computerized maintenance program began some 18 years ago in the Mining Division of USSteel. It started with a manual system of preparing cards containing preventive maintenance instructions that had to be performed on some regular basis. We were very quickly overtaken by the massive task of administration and distribution of instruction cards to the users. The task became insurmountable as more mines were added to the system, mines that were spread over a large geographic area. It also became evident that the ability to make changes in equipment assignments and in the "what to do" instructions would require more time than had been anticipated.

Jan 1, 1986

By Jerry M. Whiting, Samuel Frimpong

Superior ventures selection and the subsequent management of their development and production are crucial in the competitive environment of the upstream minerals and energy industry. An important element of this chain is the management of uncertainty and risk dynamics. In the world of faster and more complicated technological and environmental changes, international competition and commodity market dynamics, thorough and sophisticated valuation must be carried out to establish a venture's value and return on investment. Thus, managers and investors must use methods that respond to market dynamics, investment and feasibility study options and provide relevant information for strategic investment decisions. Conventional methods have no built-in procedures to help investors analyse these options. Modern financial methods based on the dynamic arbitrage theory overcome these and other limitations of conventional methods. In this study, dynamic arbitrage theory has been used to formulate 3D parabolic differential equations that govern the stochastic processes of a copper mining venture with ongoing feasibility studies. The alternate direction implicit algorithm is used to solve the numerical approximations of the differential equations and their boundary conditions. Phase dynamics of the venture have been analysed to provide investors the appropriate timing for strategic investment decisions. The study also shows the amount and value of appropriate feasibility studies required to maximize the value of the mining venture.

Jan 1, 1996

By E. J. Beckman, R. M. Enick, C. Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic platinum group metal complexes from an aqueous phase. However, because conventional extractant-metal complexes are not soluble in liquid carbon dioxide, this can be achieved only if highly carbon dioxide-soluble extractants are developed. For example, trioctylamine-gold chloride is not soluble in liquid carbon dioxide, although trioctylamine is CO2 soluble. The novel CO2-soluble extractants presented in this paper have a CO2-philic fluorinated tail to enhance solubility and a conventional amine head group for extraction of metals. Both the extractant and the extractant-metal complex are soluble at ambient temperature at pressures from 7 to 35 MPa. Efficiency factors as high as 2.23 have been measured using 1,1,2-trichlorotrifluoroethane (TCTFE), a low pressure screening liquid for carbon dioxide, indicating that these compounds will strongly bind the metal chloride. For example, 84% of Pt-chloride was extracted into TCTFE using a 3.5:1 ratio of a double¬tailed fluoroalkyl amine extractant: metal chloride. An 88% recovery of Pt-chloride into high-pressure liquid carbon dioxide was achieved using the same extractant at a 3.5:1 ratio. Therefore, it appears possible to replace organic solvents with liquid carbon dioxide during the extraction of platinum chlorides if highly carbon dioxide-soluble extractants agents are employed.

Jan 1, 2002

By T. Chandler, R. Buchan, J. H. Blowes, E. G. Haldeman

The regional geological setting and nature of the serpentinized ultramafic rocks are described. It is postulated that lateritization started in Miocene time. Repeated uplifts led to at least four physiographic cycles and to the development of a mature lateritic soil profile. Complete profiles are subdivided from top to bottom as follows: Zone A - chocolate-brown limonite; Zone B - ochre-brown limonite; Zone C - soft serpentine; Zone D - hard serpentine; Zone E - serpentinized peridotite; Zone F - ultramafic rock. Zones A and F rarely attain ore grade. Canga is conspicuously absent. Rocky ore of Zones D and E amounts to 40%, limonite ore of Zone B to 25% of total ore reserves. Nickeliferous serpentine is the major crystalline phase in Zone C. In this zone and deeper, crystalline quartz occurs, particularly in fracture zones where nickeliferous cryptocrystalline quartz is of ten accompanied by garnierite.

Jan 1, 1979

By M. Alnot, J. A. Mielczarski, J. J. Ehrhardt, J. M. Cases

The flotation behavior of minerals depends on the balance between hydrophobic and hydrophilic species present at the surface of the minerals. The direct characterization of the interfacial products formed by the interaction of water and an aqueous solution of amyl xanthate with chalcopyrite, tetrahedrite and tennantite (the two former contain antimony and arsenic) were carried out by X-ray Photoelectron Spectroscopy (XPS) and infrared (IR) reflection spectroscopy. The experimental data collected from in-situ (IR ATR) and ex-situ (XPS, IR External Reflection) measurements have let us determine the types of the adsorption products and to propose mechanisms of interaction between the aqueous solution of surfactant and surface of the investigated minerals. It is shown that two major processes take place at the mineral interfaces: (i) the interaction with water and oxygen resulting in the formation of the oxidation products which are mainly hydrophilic (but also a hydrophobic product was found), and (ii) the adsorption of xanthate producing different types of hydrophobic surface products. The results obtained show differences in the composition of the outermost atomic layers of the investigated minerals which obviously will produce differences in the flotation behavior of these minerals. This work forms a good fundamental basis for a better separation between copper minerals containing arsenic and antimony, and chalcopyrite.

Jan 1, 1995

By Barry Silverman

As a significant mineral supplier, consumer of primary fuels, and producer of wastes and emissions to air, water, and land, the domestic copper industry through its investment and operating decisions influences the nation's economy and the environment. In turn, the copper industries' decisions are influenced by various factors: government energy and environmental policies, economic conditions, and technological considerations. The authors have developed a framework for assessing in an integrated manner the impact of these factors on the future investment and operating decisions made by copper firms. Specifically, this model is designed to capture the technology forcing nature of regulatory constraints, the differential situation of individual copper deposits and plant locations, and the price of factor inputs and conditions in the nation's economy. The capability to do this has only become real because of the decision of the U.S. Bureau of Mines to create Mineral Availability system1 or MAS. This system contains detailed but confidential information about each mine and mill in each of 35 mineral industries." Without MAS or a similar information system, the utilization of the methodology we offer would be impractical, but with. MAS it offers a unique technique of dealing with environmental-resources policy questions.

Jan 1, 1979

By J. Harrison Daniel

Increasing mechanization of underground mining operations throughout the years has reduced the dependency on large, concentrated working forces. Fewer workers in scattered locations, coupled with the versatility of diesel equipment to load and haul personnel, supplies, and mineral ore, has made diesel equipment attractive in mine feasibility and design studies. The use of the mobile equipment along with higher production or "bulk" mining methods provides for more efficient mineral extraction systems. These systems are expected to become more widespread until long-term research provides a further evolution to more complete automation of underground mining. The U.S. Department of the Interior, Bureau of Mines, has been conducting research to reduce the health and safety hazards posed by increasing use of diesel equipment and the higher power ratings being proposed. The goal is to provide for safe and efficient use of the equipment. The National Institute for Occupational Safety and Health has recommended that diesel exhaust be regarded as a potential occupational carcinogen adding importance to the Bureau's research program. The paper describes advances in engine design, the use of diesels in mining operations, and significant health and safety research accomplishments of the Bureau of Mines. These accomplishments will help assure that diesel equipment remains an option for determining the most efficient system to mine an ore body.

Jan 1, 1989

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008