Search Documents

By J. W. Hawley, G. S. Austin, L. A. Brandvold, J. Renault

Soil next to a smelter abandoned about 100 years ago near Socorro, NM was found, by the US Environmental Protection Agency (EPA), to contain high Pb concentrations. Detailed characterization of the soil by the New Mexico Bureau of Mines and Mineral Resources (Bureau) shows that the highest Pb concentration is in the clay-size fraction, although this fraction accounts for only 1 to 3 wt % of the soil. The depth of contamination, determined in areas relatively undisturbed since the smelter was abandoned, is no more than 76 mm (3 in.). Because of the soil's alkalinity, the Pb mobility is dominated by the movement of Pb-bearing particles, as opposed to chemical transport in solution.

Jan 1, 1994

By St. E. Deák

There is a large preoccupation concerning the development of expert tools (ET) in the mining industry, in order to minimize the impact from waste dumps and processing residues on the environment. In this paper, the authors present a new approach for the development of an expert tool for each area under study, in order to minimize production and disposal of mining wastes on the environment, by taking into account the DKRControl method as well as the Ecomining principles, regarding among others hazard identification, impacts and monitoring. Due to the complexity of this topic a reliable ET requires input from a number of interested stakeholders. The design and management of a mining waste disposal site over its entire life cycle is also considered very important.

Jan 1, 2008

By A. E. Stewart

Slope design in an open pit mine includes determining bench height, bench face angle and berm width. Case histories are presented of two highwall slopes (160 and 220 m or 525 and 720 ft high) excavated in dipping strata in an op¬erating coal mine. These examples illustrate the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in approximately the same lithologic and structural environment. The main differences between the slopes were the angle at which the bench faces were excavated and the excavating methods that were used. Relevent aspects are also described of the engineering geology, slope design and excavation procedures.

Jan 1, 1998

By L. W. Saperstein, M. C. Radomsky, D. L. Passmore, J. D. Bennett

About 60 small surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the degree of safety exhibited by workplace behavior and conditions. Data were collected through the use of on-site safety instruments covering seven major occupational positions typical of small surface mines. Workplace events observed (acts and conditions) were assigned a hazard classification. Feedback was initiated to improve safety performance in areas failing to conform to appropriate safety standards. Results suggest that the variety of unsafe acts and conditions associated with the companies observed are extensive. Further, the experiences drawn from this pilot project have proven the need to pursue this behavioral approach. Future research should concentrate on subjecting the present approach to a strict experimental design involving randomly selected “poor risk” mines.

Jan 1, 1987

By Ehsan Alavi, Glen Frank, Michael DiPonio, Mike Mooney, Lisa Mori

"A study was conducted on the N125 project in Seattle to investigate the use of apparent density as an assessment tool for the effectiveness of soil conditioning. The formation of an air bubble as well as the plugging of cutterhead and excavation chamber can be a result of improper soil conditioning. Both air bubble formation at the top of the excavation chamber and developing plugging issues can be identified by analyzing the apparent densities in the excavation chamber. In this study, apparent densities less than unity were observed in the upper portion of both northbound and southbound TBMs, suggesting the presence of an air bubble. Apparent densities greater than the in-situ soil density were observed in the lower portion of the excavation chamber. Particularly high values of apparent density were coincident with clogging observed at multiple locations along the alignment. The combination of less than unity upper chamber apparent density and very high apparent density in the lower portion of the chamber are related, and indicate the inability of the TBM to effectively condition and mix the soil in the chamber.INTRODUCTIONProper soil conditioning in EPB tunneling offers many advantages to the quality and productivity of the project. There are few operational parameters that can be used to assess the soil conditioning performance such as advance rate, torque, thrust, chamber pressure signature, etc. One of the other parameters that potentially can be used is the apparent density. The apparent density of the material in the chamber was introduced by Guglielmetti et al. (2003) as the vertical chamber pressure gradient calculated from the physical relation between the horizontally measured chamber pressures and the vertical distance between the pressure sensors. Guglielmetti et al. (2003) introduced apparent density as a measure to ensure the excavation chamber is filled with material. To guarantee face stability the authors suggest to keep the apparent density over a certain limit so the material is able to transfer effective stress to the virgin soil, and thus provide support of the excavation face. They implemented this method at the Metro project in Porto, Portugal.Comparing the vertical gradient of the horizontal chamber pressures to the densities of excavation chamber samples, Bezuijen et al. (2005) discovered that the gradient is not necessarily representative of the muck density. They assumed that the yield stress of the muck as well as the adhesion between the muck and the cutterhead and bulkhead material have an influence on the vertical gradient during mining (Bezuijen et al. 2005, Bezuijen & Talmon 2014)."

Jan 1, 2016

By R. W. Bartlett

Aeration curing, over- a long duration in wet- red stockpiles, shows promise as an affordable pretreatment method for oxidizing gold encapsulating sulfide minerals, and possibly organic matter, in low grade refractory ores. Following aeration pretreatment, the ore is reclaimed, neutralized, and cyanide leached by conventional practices. Large tonnages of subeconomic material, including mine stripping waste, may he converted into ore by this new technology. The results presented show that a successful application of this technology will likely require crushing to about -2 cm (-3/4 in.), followed by aeration in a wet stockpile for long periods, up m three years. Natural convection may he inadequate, hut forced air ventilation, at modest pressures and power consumption, is affordable.

Jan 1, 1991

By Dave Willis

In ME'S 1994 Powder River Basin (PRB) coal transportation article, the lead author described some destinations pursued by the railroads. As with many destinations, though, they turned out to be merely stops on the way to places that have yet to be reached. Along the way, the railroads discovered that making it better is a continuous process, not just something done in several phases. This was always known but not at the awareness level that exists in 1998 railroad environments. This update of the 1994 article includes railroad companies' plans for the future of rail transportation in the PRB.

Jan 1, 1998

By Steven Brown, Richard Stephenson, Richard Partch, Hongyu Wang

Filler technology has enjoyed a revolution in attention and achievement in the past half century. The genesis of the advancements is greater find a mental understanding of the synthetic chemistries for and physical properties of colloidal matter and instrumentation capable of characterizing particle size, shape and surface features. Several advanced chemical methods for processing powders are now employed in ceramic, electronic, imaging, medicinal and plastic technology. This presentation will highlight solution phase synthetic methods for in situ coating of fillers such as SiC, Al2O3, AlN and SiO2 and some properties of the product solids.

Jan 1, 2003

By Michael J. Mankosa

Carpco has recently evaluated the use of various mineral processing techniques for secondary materials recovery. These applications include recycled foundry sands, plastics and secondary metals. This paper describes different recycling applications and the associated separation solutions. Results from extensive laboratory-and pilot-scale test work in each area are discussed. Industrial installations resulting from this test work will be presented. A detailed description of an industrial installation patented by Carpco for the recovery of plastic and metallics from current waste by-products is presented.

Jan 1, 1997

By Anthony Delvescovo, Gregory F. Aluce, Joseph A. Sopko, Lyle C. Smith

Construction of a 13m shaft through approximately 100m of water bearing soils and another 100m of bedrock was attempted using the Slurry Diaphragm Wall Method with a combination of deep dewatering wells. During excavation within the slurry wall, unexpected groundwater inflows occurred in a structure of loose silty sands. Artificial ground freezing was selected as a remedial method to seal the leaking slurry wall, and as a primary excavation support and groundwater control method for the 30m of overburden material below the base of the wall. Design of the ground freezing system required analysis of both the structural requirements of the unsupported soil, the frost effects against the existing slurry wall and the groundwater control in the area of the breech in the wall. These design procedures are summarized, and construction and excavation techniques and corresponding schedules compared in this paper. Advanced drilling techniques, ground freezing quality control and general contractor procedures for efficient shaft construction are discussed.

Jan 1, 1993

By J. D. Miller, Z. S. Nickolov

Sum Frequency Spectroscopy (SFS) is a powerful nonlinear optical technique to study interfaces at the molecular level. SFS has one major advantage over conventional vibrational spectroscopic methods, such as infrared (IR) absorption and Raman scattering, in that the method is inherently interface specific. As a result, the spectroscopy of molecules residing in the interfacial region can be probed selectively without any contributions from the molecules present in the more pervasive bulk phases. Analysis of SF spectra can yield information on population, structure, and orientation of interfacial species with several nanometers in-depth resolution. The recently acquired SF spectrometer at the University of Utah opens new possibilities for investigation of interfacial phenomena of great importance for separation technology, materials research, nanotechnology, bioengineering. Its application to studies of liquid/gas, solid/liquid, and solid/gas interfaces will be discussed.

Jan 1, 2004

By N. Oswald

As coal mines age and become more developed, ventilation modeling becomes more important for the planning and continued operation of the system. Numerous studies have been performed and presented that address the collection of data and measurement of airway friction factor and resistance per unit length values. However, a quantitative analysis of the resistance for stoppings in coal mines for different construction materials and methodologies has not been adequately addressed. In order to develop an accurate/realistic ventilation model both airway resistances and stopping resistance values need to be determined. Over the course of the past two decades Mine Ventilation Services, Inc (MVS) has measured the resistance of stoppings of various construction types in mines throughout the world. An analysis of this data is presented in this paper along with a discussion of measurement methodology.

Jan 1, 2009

By K. A. Natarajan

This paper deals with the various electro- and biochemical mechanisms involved in the bioleaching of multisulfide minerals such as those containing copper-lead-zinc and copper-nickel-iron. Galvanic series for sulfide minerals consisting of pyrite, chalcopyrite, galena, sphalerite, pentlundite, and pyrrhotite in an acid bacterial leaching system is illustrated, and the role of relative electrochemical activity on selective dissolution is discussed. Typical leaching results are shown to illustrate the practical applicability of galvanic effects in bioleaching of multisulfides. Attachment of Thiobacillus fewooxidans onto chalcopyrite and sphalerite mineral substrates is illustrated through scanning electron micrographs. The role of high-metal-tolerant, specially adapted strains in the leaching of multimetal concentrates is also outlined.

Jan 1, 1987

By Zhen-lu Zhao

The manipulators possibly used in underground mining must deal with unpredictable obstacle while keeping certain positions and orientations of end effector, and in some cases, are required to possess redundant joints in order to be more flexible. This kind of manipulators might be fitted with jumbo drill or platform as auxiliary to potentially deal with some utility works in versatile way, such as installing rock bolts, guniting, blasting, charging, surveys and measuring work, etc.. This paper describes numerical procedures of performing inverse kinematic problems for redundant manipulators .The procedures, based on the generalized pseudoinverse of Jacobian matrix, are developed to lead to kinematic solution at both singularity and ill conditioning, and to guarantee continuous sequence of positions of the end effect or. Furthermore, the solution to optimization and obstacle avoidance is investigated. A numerical example is shown to illustrate the approach.

Jan 1, 1989

By V. Srajer

Operations research includes the application of systems analysis to mining operations, the acquisition of field data and the creation and verification of computer models of these operations. These activities result in the generation of computerized mine planning tools which have a firm base-in observational facts. The Surface Mining Laboratory of the Canada Centre for Mineral and Energy Technology (CANMET), in Devon, Alberta has been engaged in operations research activities since 1982. The work includes computer simulation of truck/shovel, continuous mining equipment and dragline operations. Other examples include cooperative programs with industry (such as the demonstration and evaluation of an integrated truck management system), the development of a device to measure off-highway truck rolling resistance, and an automated remote data transmission network. The presentation outlines existing and proposed research projects of the Operations Research group.

Jan 1, 1989

By Y. J. Wang

In the, mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs. -quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1997

By Kevork Chouzadjian, Gary Davis, Nicholas Katsikaros, Bruce Kelley, Mellie Mavatoi

A process has been developed to recover gold and copper from two waste materials at the Bougainville Copper Limited mine in Papua New Guinea. It involves the bioleaching, in reactors, of a pyrite concentrate to liberate refractory gold and generate sulphuric acid, ferric sulphate and biomass for bacterial leaching of a chalcopyritic waste rock dump. Gold is to be recovered by cyanide leaching and copper by solvent extraction/electrowinning. The reactor bioleaching was developed in continuously operated reactors of 1 m3 capacity by CRA Advanced Technical Development at Cockle Creek, while the dump leaching was developed in 750 kg columns on site at Bougainville Copper Limited. The process was to be piloted on site.

Jan 1, 1990

By James L. Crowe

Electric-power-generating plants fired by fossil fuels are faced with increasingly stringent requirements for control of sulfur emissions. Several approaches for limiting these emissions, or for operating such facilities in an environmentally acceptable manner, are being pursued. Some of the approaches are based on the use of naturally occurring carbonate rocks or of materials derived from them. This paper discusses primarily the carbonate-rock-based processes being developed for control of sulfur dioxide emissions from fossil-fueled electric-power-generating plants. It includes a discussion of the role of carbonate rock materials in removal of sulfur dioxide from stack gases after combustion, capture of gaseous SO2 during the combustion process, and removal of sulfur from fuel prior to complete combustion. Materials derived from carbon- ate rocks are generally used in processes which convert the sulfur to a throwaway product, but there are also proposed processes in which the sulfur is converted to a useful product and the absorbent is regenerated for reuse.

Jan 1, 1974

By John A. Ames

Limestone for portland cement must be beneficiated to produce uniform raw material for the kiln. Careful quarrying and selective recovery are factors in this process, but the chief aspects of beneficiation are "in plant" processes, such as crushing and screening, washing, grinding, flotation, and heavy-media separation. Numerous technical and economic problems exist. Detailed studies of the limestone deposit and the stone itself are required for intelligent beneficiation. As used in this paper, beneficiation is defined as the improving of limestone composition so as to produce an economically usable raw material A limestone deposit is defined as a mass of limestone which can be recovered, by quarrying or mining, for sale or for use in a commercially profitable operation. The stone may require elaborate processing, or it may qualify with little or none. Obviously, the "commercially profitable" qualification may change as the economy changes. Potentially commercial deposits may be of much better quality than actually developed deposits, and yet may be denied development for various economic reasons.

Jan 1, 1966

By James R. Tompkins

This paper details the successful progression of a promising exploration property into a producing gold mine in only 35 weeks on schedule and on budget. While under construction, an extensive exploration program continued to add to the mine life through the increase in reserves, resulting in a decision to increase the mill capacity from 500 tonnes per day to 1000 tons per day while maintaining the original construction schedule. Details are provided on the unique geology at the Puffy Lake Gold Mine, development from the exploration stage through construction and ultimately to production, with a detailed flow sheet. In addition, of note is the successful change over from contract mining to the hiring of Pioneer personnel who are successfully carrying on both stope mining and development. Operating costs per ounce of gold production are projected at $185 U.S. and alternate methods of mining are currently being examined which could further reduce operating costs.

Jan 1, 1988